|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 2 | All kinds of soil. |
| 3 | Providing and laying in position excluding cement concrete of level: specified grade the cost of centering and shuttering - All work up to plinth |
| 4 | 1:2:4 (1 cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 5 | 1:5:10 (1 cement : 5 coarse sand (zone-Ill) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 6 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: |
| 7 | 1:1.5:3 (1 cement : 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 8 | Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement: 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 9 | Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-Ill) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 10 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : |
| 11 | 1:1.5:3(1 cement: 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 12 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement: |
| 13 | 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 14 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 15 | Foundations, footings, bases of columns, etc. for mass concrete |
| 16 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 17 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 18 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. |
| 19 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 20 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: |
| 21 | Cement mortar 1:6(1 cement :6 coarse sand) |
| 22 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : |
| 23 | Cement mortar 1:6(1 cement : 6 coarse sand) |
| 24 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. |
| 25 | Cement mortar 1:4(1 cement :4 coarse sand) |
| 26 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3(1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 27 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. |
| 28 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 29 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 30 | 300x16 mm |
| 31 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 32 | 150x10 mm |
| 33 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 34 | 100 mm |
| 35 | Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. |
| 36 | Providing and fixing to existing door frames. |
| 37 | 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/ Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table 3 of IS: 14856, complete as per direction of Engineer-in-charge. |
| 38 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 39 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 40 | Hot finished welded type tubes |
| 41 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with: |
| 42 | 4.0 mm thick glass panes |
| 43 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. |
| 44 | Providing and laying Vitrified tiles in floor in diferent sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. |
| 45 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 46 | Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : |
| 47 | Ridges plain (500- 600mm) |
| 48 | 12 mm cement plaster of mix: |
| 49 | 1:6 (1 cement: 6 coarse sand) |
| 50 | 15 mm cement plaster on rough side of single or half brick wall of mix: |
| 51 | 1:6(1 cement: 6 coarse sand) |
| 52 | 12 mm cement plaster finished with a floating coat of neat cement of mix: |
| 53 | 1:4(1 cement: 4 fine sand) |
| 54 | Finishing walls with Acrylic Smooth exterior paint of required shade: |
| 55 | New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 56 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 57 | Two or more coats on new work |
| 58 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: |
| 59 | One or more coats on old work |
| 60 | Finishing walls with Acrylic Smooth exterior paint of required shade: |
| 61 | Old work (Two or more coat applied @ 1.67 Itr/ 10 sqm) on existing cement paint surface |
| 62 | Old work (One or more coat applied @0.90 Itr/10 sqm). |
| 63 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. |
| 64 | In cement mortar |
| 65 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: |
| 66 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 67 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: |
| 68 | White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps |
| 69 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 70 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. |
| 71 | 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. |
| 72 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall |
| 73 | 20 mm nominal dia Pipes |
| 74 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. |
| 75 | 20 mm nominal dia Pipes |
| 76 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work - Exposed on wall |
| 77 | 15 mm dia nominal bore |
| 78 | 25 mm dia nominal bore |
| 79 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, including making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : |
| 80 | 15 mm dia nominal bore |
| 81 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work |
| 82 | 25 mm dia nominal bore |
| 83 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 84 | 25 mm nominal bore |
| 85 | 32 mm nominal bore. |
| 86 | 40 mm nominal bore |
| 87 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : |
| 88 | 20 mm nominal bore |
| 89 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 90 | 45 cm length |
| 91 | 15 mm nominal bore |
| 92 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : |
| 93 | 15 mm nominal bore |
| 94 | 20 mm nominal bore |
| 95 | 25 mm nominal bore |
| 96 | 32 mm nominal bore |
| 97 | 50 mm nominal bore |
| 98 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 99 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : |
| 100 | 15 mm nominal bore |
| 101 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. |
| 102 | 15 mm nominal bore |
| 103 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. |
| 104 | 15 mm nominal bore |
| 105 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 |
| 106 | 15 mm nominal bore |
| 107 | Providing and fixing PTMT, push cock of approved quality and colour. |
| 108 | 15 mm nominal bore, 98 mm long, weighing not less than 75 gms |
| 109 | Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm precast R.C.C. horizontal grating with frame and vertical grating complete as per standard design : |
| 110 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 111 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 112 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 113 | Constructing soak pit 1.20x1.20x1.20 m filled with brick bats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. |
| 114 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : |
| 115 | For fixed portion |
| 116 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 117 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) |
| 118 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 119 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): |
| 120 | With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 121 | Supplying and filling in plinth with sand under floors, including dressing all complete. |
| 122 | Deduct GST Factor on DSR-2023 Items @ total of DSR rates - 0.973 of DSR rates) i.e 1329091.54 x 0.973 = Rs. 1293206.06 - 1329091.54 = (-)35885.47 (Variation Amt) |
| 123 | Add for Cost index on DSR 2023 @ 4.03% on 1293206.06 =52116.20 |
| 124 | Electrical |
| 125 | Providing and installation of highbay luminaires with pressure die cast housing , integrated PC optics 100 watt capacity and 150 Lm/W efficacy , 4 KV in built and 10 KV external surge protection , IP 66 ingress protection with additional chain etc including connection , installtion testion commissioning complete etc. as required (with 5 Year manufacturer Warranty) category BIHNK 100 watt WH NB PC SD make Bajaj or equivalent make of Philips / Havells / Wipro etc . |
| 126 | SITC of integrated pressure die-cast alluminium (all-in-one i.e. Light, Battery & Panel source along with MPPT charge controller, sensor in single aluminium die-cast casing) Off-grid solar light on existing pole complete with lumen output from 3000-3500 Lumen, Battery(LiFePO4) capacity 20 Ah , 12.8 V & panel capacity min- 35 Watt, Mono crystalline, LED Lifespan 50000 Hrs, CRI> 70, Luminious Efficacy >(100-140) Lm/W, CCT- 5700K, Panel Efficeiency > 90, Open, Short Circuit protection, andReverse polarity protection, IK for Lens IK08, IP65 fitting, complete etc. as required(with 5 Year manufacturer Warranty for complete solar light sysytem) |
| 127 | SITC of hybrid integrated pressure die-cast alluminium (all-in-one i.e. Light, Battery & Panel source along with MPPT charge controller, sensor in single aluminium die-cast casing) Off-grid and On-grid solar ligh on existing pole sytem complete with lumen output from 3000-3500 Lumen, Battery(LiFePO4) capacity 20 Ah , 12.8 V & panel capacity min- 35 Watt, Mono crystalline, LED Lifespan 50000 Hrs, CRI> 70, Luminious Eficacy > (100-140) Lm/W, CCT- 5700K, Panel Efficeiency > 90, Open, Short Circuit protection, andReverse polarity protection, IK for Lens IK08, IP65 fitting, complete etc. as required(with 5 Year manufacturer Warranty for complete solar light system) |
| 128 | Providing and making steel pole collar with cement concrete (1 cement : 3 coarse sand : 6 stone aggregate 20mm) of specified size and shape including form work, plastering if required, curingetc as required. (volume of pole/ pipe not to be deducted). |
| 129 | Providing, fixing and making suitable arrangement on existing pole for fixing of solar LED light with GI accessories such as Reducer,GI Nipple of suitable length etc as required including dismentling of existing arrangement.( All Material should be ISI Marked) |
| 130 | Supply and drawing of 3 x 1.5 sq mm PVC insulated, FRLS PVC sheathed copper conductor multi core flexible cable into the existing street light pole, making connections at one end with the street light fitting fixed to the top of the pole and the other end with the control gearbox, including drawing out the burnt-out wires from the pole if required, etc. as required. |
| 131 | Providingand installation of GI pipes class B marked with IS: 1239 in 6 m length, complete in all respects to the satisfaction of Engineer-in- Charge. (Make : ISI marked B class Jindal Hisar / Tata / Prakash Surya / Swastik / Zenith maked G.I. pipe) |
| 132 | 65mm Dia |
| 133 | Dismantling of pole/street light standard/ strut embedded in cement concrete foundation etc. as required. |
| 134 | Less credit for the unserviciable items dismantled items during execution of the work. |
| 135 | Battery |
| 136 | Polycrystalline Panel |
| 137 | Mono Crystalline Panel |
| 138 | GI Pipe Please Enable Macros to View BoQ information |
