Tender For Addition/Alteration Of Md Qtrs Of Zone-A At Sector -9 At Icgs Gandhinagar Under Ge (I) (Cg) Gandhinagar
Tender Value
41.54 Lakhs
Estimated cost
Bid Submission
15 Jul 2026
6 days left
EMD
83100
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Gandhinagar → Gujarat
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition/Alteration Of Md Qtrs Of Zone-A At Sector -9 At Icgs Gandhinagar Under Ge (I) (Cg) Gandhinagar
BOQ
| Sl. No. | Item Description |
| 1 | Taking down cement or cement lime plaster wall and ceiling including in patches, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 2 | M&L for Dubbing out average 20 mm thick CM 1:4 on irregular face of old wall/ceiling fin facias chajjas etc complete all as specified and directed. |
| 3 | M&L Rendering including in patches, 10 mm thick in cement mortar 1:3 on concrete surfaces,Chajjas in ceiling finished even and smooth without using extra cement complete all as specified and directed. |
| 4 | M & L Preparation of newly plastered ceiling surfaces and applying three coat of white wash. (above item shall be applied by the brush not by spray gun) complete all as specified and directed. |
| 5 | M & L rendering 10mm thick on fair faces or other than fair faces of brick work,concrete or stone masonry surfaces in CM 1:6 finished even & smooth without using extra complete all as specified and directed. |
| 6 | M & L Preparation of newly plastered wall surfaces and applying two coat of white wash complete all as specified and directed. Note: Above item shall be applied by the brush not by spray gun. |
| 7 | M & L Preparation of newly plastered wall surfaces and applying two coats oil bound distemper over a coat of primer complete all as specified and directed. Note: Above item shall be applied by the brush not by spray gun. |
| 8 | M & L rendering 15mm thick on fair faces of brick work,concrete or stone masonry surfaces in CM 1:4 with using water proofing compound and finished even & smooth without using extra complete all as specified and directed. |
| 9 | M&L Preparing new plastered or unplastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and directed.Note: Above item shall be applied by the brush not by spray gun. |
| 10 | M&L Preparing new plastered or unplastered surfaces of walls and applying two coats of all weather coat exterior emulsion paint over a coat of primer complete all as specified and directed.Note: Above item shall be applied by the brush not by spray gun. |
| 11 | Supply only water proofing compound complete all as specified and directed. |
| 12 | Wire netting of galvanized steel wire 0.91 mm dia fixed with tinned tacks of wire staples size of mesh 20 mm as in chhajas / ceiling plaster repair works complete all as specified and directed. |
| 13 | M&L for 3mm thick (1.5mm thick each in two layer application) wall care putty of old surface of wall incl rubbing down with sand paper to have even and smooth surface complete all as specified and directed. |
| 14 | Demolition of PCC block/stone masonery built in cement mortar of any specification and in any position complete all as specified and directed. |
| 15 | M & L brick work with flyash bricks straight or curved onplan exc 6 m mean raidus built in cm 1:6 complete all as specified and directed. |
| 16 | Providing cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in coping, kerbs,benching and the like, including weathering slighthy rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed. |
| 17 | Demolition of cement concrete (un-reinforced) in floors / pavings, (Below or above GL) and of any description and in any posting not otherwise specifically provided complete all as specified and directed. |
| 18 | M&L PCC 25 mm thick 1:2:4 type B1using aggregate as in leveling course complete all as specified and directed. |
| 19 | Materials and labour 15mm thick screed bed or bedding layer in CM 1:6 for laying flooring etc complete all as specified and directed. |
| 20 | Materials and labour for 10mm thick screed bed in CM 1:4 for laying of wall tiles/kota stone. complete all as specified and directed. |
| 21 | M&L for 20 & 25mm thick machine cut kota stone slabs of suitable size of kota stone as in floors bedded in grey jointed, pointed in coloured cement incl cutting and polishing complete all as specified and directed. |
| 22 | M&L for 20 & 25mm thick machine cut kota stone slabs of suitable size of kota stone bedded in grey jointed, pointed in coloured cement incl cutting and polishing all as spd but vertical surfaces as in skirting /dado complete all as specified and directed. |
| 23 | Dismentling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to stores and and rubbish off the permises.complete all as specified and directed. |
| 24 | M&L Vetrified ceramic tiles 10mm thick (Square/rectangular) polished light shade area of each tiles n exc 0.36 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles all as specified and as directed (Asian, Orient, Somany & Johnson 1st Grade) complete all as specified and directed. |
| 25 | M&L Vetrified ceramic tiles 10mm thick (Square/rectangular) polished light shade area of each tiles n exc 0.36 Sqm in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles all as specified and as directed (Asian, Orient, Somany & Johnson 1st Grade) complete all as specified and directed. |
| 26 | M & L for glazed ceramic coloured tiles 7mm thick 300 x 450mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the complete all as specified and directed. |
| 27 | M & L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or oloured cement to match complete all as specified and directed. |
| 28 | M & L 20 mm thick Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed. |
| 29 | M & L 12 mm thick wall lining Granite (of any type) tiles 12mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed. |
| 30 | Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc, laid bedded and pointed in any mortar complete all as specified and directed. |
| 31 | M&L for hard core of broken stone of guage n.exc 63mm deposited spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface.complete all as specified and directed. |
| 32 | M&L for PCC 1:4:8 type D-2 using 40mm graded stone agg in sub base flooring thickness 75mm complete all as specified and directed. |
| 33 | M&L for Parking tiles heavy duty vitrified ceramic tiles 30 cm x 30 cm x 10 mm thick , set , jointed and pointed in neat cement slurry over and including 15 mm thick screed bed or bedding layers in CM 1:6 for laying floor finishes in floors , path / hard standing etc with white cement and pigment (Dark shade) complete all as specified and directed. |
| 34 | M&L, for 60mm thick machine pressed precast concrete interlocking paver block, coloured with glossy finish, any shape and size, M- 35 Grade, with gray cement and pigment. complete all as specified and directed. |
| 35 | Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed. |
| 36 | M&L for sand cusioning layer for laying PCC interlocking paver block complete all as specified and directed. |
| 37 | M&L 100 mm thick cement concrete type B-2 (1:2:4) using 40 mm graded stone aggregates including spike rolling to surface or making in pression of expanded metal, while the concrete is green including forming joints. complete all as specified and directed. |
| 38 | Forming construction joint 30mmdeepx10mm wide filled with sealing compound(grade 'A'). complete all as specified and directed. |
| 39 | Precast cement concrete Kerb stone 7.5cm thick with PCC 1:2:4, using 20mm graded stone aggregate set in CM (1:6) complete all as specified and directed. |
| 40 | M& L for 75mm thick PCC 1:3:6 type C-2 (Using 40mm graded crushed stone aggregate) as in plinth protection finished even and fair without using extra cement complete all as specified and directed. |
| 41 | Taking down roof treatment any type any description on top of roof not exc 10cm thick incl removal of rubbish out side MD and complete all as specified and directed. |
| 42 | M&L for PCC 1:2:4 type B0 using 12.5 mm stone aggregate as on top of roof and roof padding benching kerbs of mud stops, rounded or chamfered on edges incl form work complete all as specified and directed. |
| 43 | M&L screed 15mm thick on RCC roof concrete surfaces in CM 1 : 4 mixed with WPC @ 3 % by the weight of cement used and finishing even and smooth without using extra cement. complete all as specified and directed. |
| 44 | M&L for applying roof treatment on top of roof with APP based polymeric membrane minimum weighing 3 Kg/sqm and minimum 3 mm thick reinforced with polyster non woven fabrick incl a coat of bituminous oil based primer (IS: 3884) @ 250gm/sqm laid on primed surface by torch application including priming complete all as specified and directed. |
| 45 | Material & Labour for applying one coat of aluminium paint on app membrane complete all as specified and directed. |
| 46 | Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings as in roof covering complete all as specified and directed. |
| 47 | Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to all, th self tapping screws.tapping screws complete all as specified and directed. |
| 48 | Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to all, th self tapping screws.tapping screws complete all as specified and directed. |
| 49 | S&F 2mm thick Fibre glass reinforced translucent corrugated with two corrugations side lap fixed with coach screw and washer in roof and / plain sheeting in wall cladding / fencing on iron frame etc complete all as specified and directed. |
| 50 | Dismantling wrought iron or mild steel work of any description complete all as specified and directed. |
| 51 | S & F framed work such as grills, cooler stand ,grating, etc., with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work or water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed. |
| 52 | M&L for preparation of new steel surface of any description not otherwise described etc 10 cm width or girth and applying two coats of applying two coats of synthetic enamel paint over a coat of a red oxide zinc primer complete all as specified and directed. |
| 53 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed. |
| 54 | M&L, Anodised aluminium snap grid with size of grid 605x605mm frame work for false ceiling complete all as specified and directed.Note: The supporting hanger comprising of mild steel rod, J bolts with necessary bolts, nuts and washers shall be measured and paid for separately. |
| 55 | M&L, Hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long (1 x 1 M) complete all as specified and directed. |
| 56 | S&F, 4 mm thick HPSC pre-primer non asbestos fiber cement building board (E-classic) decorative finish, laminated type fixed to aluminium/ CGI frame work (size 605x605 mm) with hold down clips in false ceiling complete all as specified and directed. |
| 57 | S&F 12 mm thick perforated particle boards/ tiles fixed in ceiling for insulation/ accoustic purposes with water proof topping of size 600x600mm of (armstrong/ gyprocks) , fixed to snap grid or aluminium frame work complete all as specified and directed. |
| 58 | S&F 5mm thick lnsulated PVC Wall Lining consisting of PVC Insulated Panels having expanded polystyrene (EPS) stuck to 2mm thick with wood grain printed PVC sheet duly fitted into the wall as per specifications and drawing complete all as specified and directed. |
| 59 | Taking down steel tubing 15mm bore and connections fixed/laid in any situation complete all as specified and directed. |
| 60 | S & F 16mm dia CPVC pipes with all fittings and fixed complete concealed including groove cutting for concealing to walls & ceiling or laid in floor complete all as specified and directed. |
| 61 | Taking down steel tubing 20mm bore and connections fixed/laid in any situation complete all as specified and directed. |
| 62 | S & F 20mm dia CPVC pipes with all fittings and fixed complete to walls & ceiling or laid in floor complete all as specified and directed. |
| 63 | Taking down steel tubing 25mm bore and connections fixed/laid in any situation complete all as specified and directed. |
| 64 | S & F 25mm dia CPVC pipes with all fittings and fixed complete to walls & ceiling or laid in floor complete all as specified and directed. |
| 65 | Dismantling water tanks 500 ltrs capacity complete all as specified and directed. |
| 66 | S & F in repair rotational moulded polyetlene water storage tanks (Culendrical vertical with closed top) 500 ltrs cap hoisted and fixed in position complete all as specified and directed. |
| 67 | S&F 20mm Ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe of following description complete all as specified and directed. |
| 68 | S&F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed in repair complete all as specified and directed. |
| 69 | S&F 25mm Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed in repair complete all as specified and directed. |
| 70 | M&L for 70mm thick PCC 1:2:4 type B-1 using 20 mm graded stone aggregae as in water tank platform incl nacessary form work to side of concrete complete all as specified and directed. |
| 71 | Taking down chowkats or frames with shutters without taking off shutters from the frames, area n.exc 1.50 sqm each and removal to store including cutting holes for removal of hold fast complete all as specified and directed. |
| 72 | Taking down chowkats or frames with shutters without taking off shutters from the frames, area exc 1.50 sqm but n.exc 4 Sqm each and removal to store including cutting holes for removal of hold fast complete all as specified and directed. |
| 73 | Taking down shutter area exceeding 1.00 Sqm and not exceeding 2.0 Sqm complete all as specified and directed. |
| 74 | S & F Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with M S square tubes , S&F in opening as per specification & drawing given in SSR-2004. complete all as specified and directed. |
| 75 | Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M S tubes for top & bottom rails M S frame shall be covered with heat moulded Single Side Prelam PVC sheet used instead of Plain colour PVC sheet and stile & rails having one side feathered edge and on other side 10mm 90 bent edge having a PVC sheet strip of 20 mm width struck in side with solvent cement for stiles and plain colour PVC sheets 5 mm thick for top rail, lock rail & bottom rail on either side & as gap insert for tap rail & bottom rail, paneling of plain colour PVC sheets to be fitted in the MS frame walded/sealed to the stiles & rails with suitable PVC sheet beading and joined to getger with solvent cement supplying & filling in the frame at site as per specification & drawing given in SSR-2004. complete all as specified and directed. |
| 76 | S & F aluminium anodised barrel tower bolts of extruded section size 150 mm. complete all as specified and directed. |
| 77 | S & F butt hinges, medium weight, cold rolled mild steel size of hinges 100mm. complete all as specified and directed. |
| 78 | S & F Aluminium handle cast type anodized 150 mm size. complete all as specified and directed. |
| 79 | S & F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides as per SSR (part-I) complete all as specified and directed. |
| 80 | Supply and fixing 100mm long butt hinges mild steel medium weight cold rolled ISI marked. complete all as specified and directed. |
| 81 | Supply and fixing 150mm long extruded aluminum handles fabricated type anodized, ISI marked. complete all as specified and directed. |
| 82 | Supply and fixing 200mm long aluminum anodized barrel tower bolt of extrude section ISI marked.complete all as specified and directed. |
| 83 | S&F 300mm long mild steel sliding bolts, stove enameled black, with bright bolt not less than 12mm dia complete all as specified and directed. |
| 84 | Supply and fixing as in repair Floor door stopper of aluminum allow body and tongue, 150mm overall length, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 85 | Materials and labour for preparation of new wooden surfaces of any description not otherwise described exc 10cm width or girth and applying two coats of synthetic enamels paints over a coat of pink primer complete all as specified and directed. |
| 86 | S&F 105 x 60mm size Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed. |
| 87 | Material and Labour for PCC 1:3:6 type C1 using 20mm graded mechanically crushed complete all as specified and directed. |
| 88 | Materials and labour for preparation of new steel surface of any description not otherwise described exc 10cm width or girth and applying two coats of synthetic enamels paints over a coat of red oxide primer complete all as specified and directed. |
| 89 | M&L for Powder coated aluminium section in door frame ,swing door, sliding window and partition walls complete including connecting accessories like allu grill for guard,fittings, glazing clips, handles, pivots etc fixed complete all as specified and directed. |
| 90 | M&L for Powder coated Anodised aluminium door shutters,aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, handle 2 Nos in each door ,anodised alumnium snap beading, screws etc. complete all as specified and directed. |
| 91 | M&L for Powder coated Anodised aluminium window and ventilator shutters, fixed type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws complete all as specified and directed. |
| 92 | M&L for Powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinge type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed. |
| 93 | S&F for 5.5 mm thick dark coloured glass in aluminium door windows partitions including ped/gasket complete all as specified and directed. |
| 94 | M&L 9mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed to aluminium door frame.complete all as specified and directed. |
| 95 | S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 96 | M&L Door closer hydraulically regulated,designation No. 1 universal type,suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed complete all as specified and directed. |
| 97 | S&F for Aluminium Motrice lock two lever , vertical type 75mm size for aluminium doors complete all as specified and directed. |
| 98 | Supply and fixing 100mm long butt hinges extruded aluminum medium weight cold rolled ISI marked complete all as specified and directed. |
| 99 | Supply and fixing 150mm long extruded aluminum handles fabricated type anodized, ISI marked complete all as specified and directed. |
| 100 | S&F aluminium anodised barrel tower bolt of extruded section 150mm long complete all as specified and directed. |
| 101 | S&F for floor door stopper of aluminum allow body and tongue, 150mm overall length, anodised, with hard drawn steel spring, fixed in floor. complete all as specified and directed. |
| 102 | S&F in repair for mild steel powder coated coloured drapery curtain rods 32mm dia complete all as specified and directed. |
| 103 | S&F Fancy type brackets for fixing of curtain rod complete all as specified and directed. |
| 104 | S&F Fancy type gloves for end caps of curtain rod complete all as specified and directed. |
| 105 | Taking down eaves gutter or RWP of any description complete all as specified and directed. |
| 106 | PVC (SWR) 110 mm bore pipes single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and directed. |
| 107 | All as per item here-in-above but 75mm bore complete all as specified and directed. |
| 108 | PVC (SWR) 110 mm bore bends any radius complete all as specified and directed. |
| 109 | All as per item here-in-above but 75 mm bore complete all as specified and directed. |
| 110 | S&F cast iron Nahani trap 75mm dia incl jointing to waste pipe fixed in cement concrete type B-1 1:2:4) 75mm dia fixed in repair. complete all as specified and directed. |
| 111 | S&F in repairs PVC(SWR) floor trap of 75 mm bore, plain with grating including jointing with solvent cement complete all as specified and directed. |
| 112 | S&F in repair 15mm bore dia, bib taps, fancy type, chromium plated , caste copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule pressure 15mm bore fixed to pipe complete all as specified and directed. |
| 113 | S&F in repair 15mm bore chromium plated cast copper alloy bib taps fancy type with , screwed down for iron pipe or for brass ferrule and fixed complete all as specified and directed.Make : prayag Cat No-7706 or equivelent |
| 114 | S&F in repair fancy type chromium plated stop valves / angle valve, cast copper alloy with crutch or butterfly handles screwed down high pressure, screwed both ends for 15mm bore iron pipe or brass ferrule complete all as specified and directed. |
| 115 | S&F in repair 15mm bore chromium plated cast copper alloy stop valves / angle valve fancy type with , screwed down for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make : prayag Cat No-7710 or equivelent. |
| 116 | S & F in repairs 15mm bore stop valve, cast copper alloy fancy type chromium plated with long shank and cup ( concealed type ) screwed down, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed .complete all as specified and directed. Make : prayag Cat No-7818 or equivelent. |
| 117 | S&F in repair Pillar tap, cast copper alloy,fancy type with capstan head, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ wih long screwed shanks and fly nuts, screwed for iron pipe and fixed in repairs, 15 mm bore dia of pipe. complete all as specified and directed. |
| 118 | S & F in repairs 20mm bore stop valve, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed complete all as specified and directed. |
| 119 | S&F towel ring round complete all as specified and directed. Make - prayag Cat No-BA-02 or equivelent |
| 120 | S&F Corner shelf of glass, Make- prayag Cat No-BEA-42 or equivelent complete all as specified and directed. |
| 121 | S&F glass shelf 60mm complete complete all as specified and directed.Make : prayag Cat No-BEA-45 or equivelent |
| 122 | S&F cardiff health faucet with SS hose and hook complete all as specified and directed.Make : prayag Cat No-BEA-40 or equivelent. |
| 123 | S&F in repair toilet paper holder of brass chromium plated including screw and chromiun plate brass wooden / plastic cleats complete all as specified and directed.Make : Prayag Cat No-BA-38 or equivelent. |
| 124 | S&F in repair brass chromium plated shower rose 75mm size (dia) with swivel joints including 195mm long brass chromium plated arm with bend 45 degree etc complete all as specified and directed. |
| 125 | S & F in repair PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed. |
| 126 | S & F in repair Grating 125 mm dia with waste hole of PTMT ( Min wt 40 gm ) complete all as specified and directed. |
| 127 | S & F in repair 600 x 450 mm size beveled edge mirror of selected quality glass mounted on 6mm thick AC building board or commercial plywood and fixed with wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 128 | S&F in repair high density polyethylene (HDPE) pipes 40mm of presure rating 6kgf/sqq. cm complete all as specified and directed. |
| 129 | S & F brass chromium plated tubular towel rail 20mm dia 600 mm long in repair complete all as specified and directed. |
| 130 | S & F vitreous china wash basin, white, flat back, size 550 x 400mm with waste fitting of PTMT32mm size,and PVC waste pipe and fixing with new brackets including cutting and pinning in ends of brackets complete FIXED IN REPAIR complete all as specified and directed. |
| 131 | S & F repair vitreous china squatting pan Orrisa pattern size 580mm x 440mm white with integral foot rest with CI ‘100mm P’ or ‘S’ trap and fixing in lime concrete (1 lime, 2 sand and 5 aggregate), 150mm thick all round and finished just below level of rim of pan to receive the floor finishing complete all as specified and directed. |
| 132 | S&F in repairVitreous China wash down water closet pan (pedestal pattern), white (excludin fixing bolts, flushing cistern and flush pipe) with PVC sheet cover & '100mm P' OR 'S' trap. complete all as specified and directed. |
| 133 | S & F in repairs PVC 10 ltrs syphonic action type flushing cistern, low level with inlet, ball valve, float and handle including brackets, flush pipe of PVC 32mm bore and connection 15mm size 450mm long to WC pan complete all as specified and directed. |
| 134 | Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in soft/loose soil complete all as specified and directed. |
| 135 | Demolition and breaking up drain pipes (SGSW, AC or RCC) of internal dia 150mm, set in cement mortar complete all as specified and directed. |
| 136 | Concrete bed to drain pipes 150mm bore including packing under and haunching against the sides of pipes after they are laid and tested; in cement concrete 1:4:8 type D2 using 40mm graded stone aggregate complete all as specified and directed. |
| 137 | Reinforced concrete pipes, class NP2, 150mm bore, laid and jointed complete with collars. complete all as specified and directed. |
| 138 | M & L pre-cast RCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in man hole cover slabs, of any thickness, size or shape including necessary from work, finished concrete surfaces fair and even in cement mortar complete all as specified and directed. |
| 139 | M&L for mild steel deforming bar 10 mm dia and over cut to shape required including cranking bending spirally for hooking end and binding with mild steel wire (annealed) not less than 0.9 mm dia. complete all as specified and directed. |
| 140 | Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed. |
| 141 | Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed. |
| 142 | Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed. |
| 143 | Pre laminated particle board, 19/20mm thick, interior grade, pre laminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work as in pelmet boxes. complete all as specified and directed. |
| 144 | S & F tower bolt 100 mm of PTMT complete all as specified and directed. |
| 145 | S & F door handl D type 100 mm of PTMT complete all as specified and directed. |
| 146 | S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed. |
| 147 | S&F 'Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed. |
| 148 | M&L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed. |
| 149 | M&L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed. |
| 150 | M&L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment of voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed. |
| 151 | M&L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 15, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysJul 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender