Tender For special Repair To Staff Living Accn And Store Rooms At Dsomi And Provn Of Hard Standing Parking With Covered Shed For Patients Visitor And Staff At Mh Mhow Under Ge (Mis) Mhow
Tender Value
33.83 Lakhs
Estimated cost
Bid Submission
15 Jul 2026
6 days left
EMD
68000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Indore → Madhya Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Staff Living Accn And Store Rooms At Dsomi And Provn Of Hard Standing Parking With Covered Shed For Patients Visitor And Staff At Mh Mhow Under Ge (Mis) Mhow
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling of AC sheets of corrugated or semicorrugated etc. sheets in roof coverings complete all as specified and directed. |
| 2 | S&F Pre-painted galvalume aluminium zinc coating GI based profile steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa, hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) as in roof covering/ cladding to wall,including flashings , ridges, valley etc fixed with self tapping screws complete all as specified and directed. |
| 3 | S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa, hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 4 | S&F mild steel framed structural work comprising roof trusses, trussed frames, purlins, crane gantries, heavy bracket framing, beams, tees, angles, channels, flats, cleats, distance pieces and all necessary fastenings, manufactured from Grade Fe 410-W (Grade E-160) Quality-A structural steel, including cutting, drilling, welding, hoisting, erecting and fixing complete all as specified and directed. |
| 5 | Demolition of un-reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed. |
| 6 | Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish of the premises complete all as specified and directed by Engr-in-Charge. |
| 7 | M&L for 25 mm thick PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) including finishing surface of concrete topping even and rough complete as in levelling work etc complete all as specified and directed. |
| 8 | M&L for scratch free, double charged, vitrified ceramic tiles 7 to 8mm thick (square or rectangular) area of each tile not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed.tiles clours as approved by GE |
| 9 | M&L for coloured Non Skid ceramic joint free tiles 7 to 8 mm thick (Square/ Rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.18 Sqm, in floors etc,including 15 thick screed bed set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile complete all as specified and as directed. |
| 10 | M&L for glazed ceramic tiles 300X450mmX7mm thick coloured on vertical surfaces set and jointed in neat cement slurry and pointed in white or cloured cement to match over and including 10mm thick rendering of CM 1:4 complete all as specified and directed.Note: The rate includes cutting, offset work, and other related operations. |
| 11 | Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillet complete all as specified and directed. |
| 12 | M&L for providing and fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) False ceiling tiles of size 595 x 595 mm of approved texture, design and patterns having moisture contents less than 2% humidity resistance of 99% NRCO.50 to .75 as pe IS8225:1987, Noncombustible as per BS 476 (Part 4)-1970 and light reflectance of 85% (Minimum) to be laid in true horizontal level suspended on interlocking metal T Grid of hot dipped galvanized iron section of 0.33 mm thick ( galvanised @ 120 gms per sqm including both sides ) comprising of main T runners of size 15 x 32 mm of length 3000mm, cross -T of size 15 x 32 mm of length 600mm to form grid module of size 600 x 600mm, suspened from ceiling using galvaized mild steel items ( galvanizing @ 80 grams per sqm) i..e 50mm long, 8mm outer diameter M-6 dash fastener 6mm dia fully threaded hanger rod upto 1000mm length and L-swhape level adjuster of size 85x25 x 2mm galvanised iron permieter wall angle of size 24 x 24 x 0.40mm of length 3000mm to be fixed on periphery wall/ partition with the help of plastic rawl plugs at 450 mm ceneter to centre and 50mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-charge. |
| 13 | Surface dressing n.exc 30 cm deep in soft/loose soil complete all as specified and directed by Engr-in-Charge |
| 14 | M&L for moorum filling/redbajri filling under floors or in foundationds including watering & consoldation laid in layers n.exc 15 cm thick spread levelled and well rammed complete all as specified and directed by Engr-in-Charge |
| 15 | M&L for 75mm thick PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as in plinth protection and paving finishing concrete surfaces even and smooth without using extra cement including filling the expansion joints with bitumen filler / filler boards and necessary form work etc complete all as specified and as directed. |
| 16 | M&L for 100 mm thick cement concrete type D-2, 1:4:8 (using 40mm graded crushed stone aggregate) as in Sub-base to floor finishes complete all as specified and directed by Engr-in-Charge |
| 17 | M&L for providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed by Engr-in-Charge. |
| 18 | M&L for precast cement concrete 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as in Kitchen platform and Cover slab for manholes etc set in cement mortor 1:4 including use and waste necessary form work complete all as specified and directed by Engr-in-Charge.Note: Reinforced shall be measured and paid seprately. |
| 19 | S&F mild steel TMT bars 10mm dia and over, cut to length bent to shap required including cranking, bending spirally for hooping for columnshooking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engr-in-Charge. |
| 20 | All as per item No. 19.00 above but 5mm dia and over upto and including 10 mm dia in spacers, stirrups and binders complete all as specified and directed by Engr-in-Charge. |
| 21 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed by Engr-in-Charge. |
| 22 | M&L for brick work with using flyash bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 23 | M&L for brickwork with using flyash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1: 4 complete all as specified and directed. |
| 24 | Taking down cement plaster on wall of any description incl racking out joints for key, scrubbing with water etc. complete all as specified and directed. |
| 25 | M&L for rendering 15mm thick in cement mortor 1:4 on concrete or brick wall surfaces, finished even and smooth without using extra cement, mixed with WPC @ at 3% by weight of cement complete all as specified and directed.Note: WPC will be measured and paid separately. |
| 26 | Supply only integral water proofing compound complete all as specified and directed. |
| 27 | M&L for rendering 10mm thick in cement mortor 1:6 on brick wall surfaces, finished even and smooth without using extra cement complete all as specified and directed. |
| 28 | M&L for 15 mm thick cement plaster in cement mortar 1:6 on brick or concrete surface etc. on wall finished even and smooth without using extra cement complete all as specified and directed. |
| 29 | Taking down chowkats with shutters (without taking off shutters from the frame exc 1.50 Sqm and n.exc 4 Sqm each complete all as specified and directed. |
| 30 | Taking down chowkats with shutters (without taking off shutters from the frame n. exc 1.50 Sqm each complete all as specified and directed. |
| 31 | S&F Pressed steel door frames 125x60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed. |
| 32 | S&F factory Made 35 mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Flush Door Shutter of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm manufactured by \\"RAJSHRI\\" an ISO 9001 - 2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 50 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet/Kitchen/Balcony Doors.Make: RAJSHRI / make as per Particular Specification (list of Make) as approved by GE. |
| 33 | S&F 30 mm thick FACTORY MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 500 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company , Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. M.S powder coated butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube.Other hardwares should be fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in -Charge, manufacturer's specification & drawings.Make: RAJSHRI / make as per Particular Specification (list of Make) as approved by GE. |
| 34 | S&F Solid PVC DoorfFrame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening complete all as specified and directed. |
| 35 | S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. M S frame shall be covered with heat moulded prelam PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and single side prelam PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail & bottom rail; stile &rails having one side feathered edge and on other side 10mm 90^0 bent edge,Paneling of 2mm thick prelam PVC sheet on bothfaces i.e front face & back face with particle board core to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement,and including all hardware necessary for a door supplying & fixing in the frame at site as per specification & drawing.given SSR 2020 complete all as specified and as directed. |
| 36 | S&F powder coated aluminium ventilator cross section conforming to IS 63.5x38.10x1.5mm consisting of two partions upper portion shall have louvers with 3mm thick pin headed glass and aluminium wire cloth 0.30mm nominal dia of wire and average width of aperture 1.56m fixed with aluminium beads and securing on outer face of frame and lower portion of ventilation shall be fixed with 3mm thick pin headed glass with IDPE rubber gasket including aluminium beads, including preparation of jombs all around in CM 1:3 finishing even and smooth complete all as specified and directed. |
| 37 | S&F powder coated aluminium sliding glazed windows with three track shutter sliding (two shutters glazed and one shutter wire mesh) shall be following specification complete all as specified and as directed by Engr-in-Charge:-(i) Windows frame of cross section 101mm x 44mm x 1.5mm thick.(ii) Three way track for sliding shutters of cross section 91.8mm x 31.75mm x1.1mm thick.(iii) Sliding shutter frame of cross section 40 x 18 x 1mm thick.(iv) 4 mm thick tinted glass superior quality.(v) IDPE Rubber guasket for fixing of glass.(vi) Locking cleats per shutter -01 Nos.(vii) Sliding rollers per shutter - 02 Nos.including satety steel grill(viii) Aluminium wire cloth 0.30mm nominal dia of wire and average width of aperture 1.56mm for shutters 01 Nos. |
| 38 | S&F 300mm length, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed. |
| 39 | S&F 250 mm length, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed. |
| 40 | S&F 100 mm size of Butt hinges, medium weight stainless steel complete door etc. complete all as specified and as directed. |
| 41 | S&F aluminium anodised barrel tower bolts of extruded section with 100 mm long bolt complete all as specified and as directed. |
| 42 | S&F aluminium anodised barrel tower bolts of extruded section with 150 mm long bolt complete all as specified and as directed. |
| 43 | S&F Extruded aluminium alloy handles fabricated type anodised 150mm size complete all as specified and as directed. |
| 44 | S&F Extruded aluminium alloy handles fabricated type anodised 100mm size complete all as specified and as directed. |
| 45 | S&F floor door stopper of stainless steel body and tongue, anodised, with hard drawn steel spring, 140mm long, fixed in floor complete all as specified and as directed. |
| 46 | Taking down 15mm bore steel tubing and connections in any position complete all as specified and as directed. |
| 47 | Taking down 20mm bore steel tubing and connections in any position complete all as specified and as directed. |
| 48 | S&F 16mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including provision of special fittings ( Unions, elbow, Tee, Male threaded brass adaptor, Female threaded brass adaptor, Tank adaptor etc) complete all as specified and as directed. |
| 49 | S&F 20mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including provision of special fittings ( Unions, elbow, Tee, Male threaded brass adaptor, Female threaded brass adaptor, Tank adaptor etc) complete all as specified and as directed. |
| 50 | S&F 20 mm bore GI Tubing medium grade with all fittings fixed to wall/ ceiling or in floor complete as specified and directed. |
| 51 | S&F in repairs rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 500 ltrs capacity hoisted and fixed in position all as specified complete all as specified and directed. |
| 52 | S&F in repairs 20 mm dia brass ball valve, high pressure with polythene float and fly-nut complete, screwed for iron pipe or brass ferrule fixedcomplete all as specified and directed. |
| 53 | S&F in repairs 20 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 54 | S&F in repairs 15mm bore Bib taps, chromium plated cast copper alloy but fancy type, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 55 | S&F in repairs 15 mm dia fancy type stop valves/ angle cock chromium plated screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 56 | S&F in repairs angular stop valves, cast copper alloy, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. |
| 57 | S&F in repairs Bib taps, cast copper alloy with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed. |
| 58 | S&F in repairs Brass CP Tubular towel rail, 20mm dia, D type, 60cm long between flanges fixed complete all as specified and as directed. |
| 59 | S&F in repairs chromium plated shower rose 125mm sizes with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed. |
| 60 | S&F in repairs Vitreous China squatting pan , \\"Orissa\\" pattern size 580 X 440 mm white with intgrel footrest (excluding flushing cistern & flush pipe) with 110mm dia PVC SWR 'P' or 'S' trap, fixing of cistern, complete including provision of cement concrete all as specified and directed by Engr-in-Charge. |
| 61 | S&F in repairs vitreous china wash basin complete with CP pillar tap, waste coupling, MS brackets, cutting/chasing, pinning of bracket ends, making good disturbed surfaces, connection to existing water supply and waste pipe complete as specified and directed directed by Engr-in-Charge. |
| 62 | S&F in repairs PVC valveless syphonic action type flushing cistern 10 lit capacity low level white with inlet, ball valve, float and handle including brackets and 32mm PVC flush pipe complete all as specified and directed. |
| 63 | S&F in repairs PVC connection 15mm dia, 450mm long with brass ferrules on both ends fixed complete all as specified and directed. |
| 64 | S&F in repairs PTMT Shelf of weight not less than 300 gms with soap dish (tray) fixed with and including Chromium plated brass screws and wooden / plastic cleats etc., complete all as specified and as directed. |
| 65 | S&F in repairs 600mmx450mm belvelled edge looking mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood with PVC / alluminium frame and fixed to wooden plugs with chromum plated brass screws, cup washers, complete all specified and directed. |
| 66 | S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed. |
| 67 | S&F in repairs PVC (SWR ) pipes 110mm dia single socketed , in any length with rubber ring joints as rainwater, soil waste and vent pipe (with all fittings) fixed to wall or laid in trenches complete all as specified and directed. |
| 68 | S&F in repairs PVC (SWR ) pipes 75mm dia single socketed , in any length with rubber ring joints as rainwater, soil waste and vent pipe (with all fittings) fixed to wall or laid in trenches complete all as specified and directed. |
| 69 | S&F in repairs PVC (SWR) bends with access door any radius 110mm bore complete all specified and directed. |
| 70 | S&F PVC (SWR) junction single (single T) equal or unequal with access door of bore 110mm complete all specified and directed. |
| 71 | S&F PVC (SWR) vent cowl 110mm bore complete all specified and directed. |
| 72 | S&F in repairs PVC (SWR) Floor trap/Nahani trap plain or multi with stainless steel grating incl joinig to waste pipe with solvent cement joint dia of outlet 75 mm bore complete all as specified and directed. |
| 73 | S&F in repairs PVC (SWR) floor trap 75mm dia outlet, plain with grating including jointing with solvent cement complete all specified and directed. |
| 74 | M&L for preparation of newly untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed. |
| 75 | M&L for preparation of newly plastered surfaces and applying minimum 1.0 mm thick white wall care putty to achieve an even, smooth and uniform surface, including rubbing, cleaning and all necessary surface preparation and applying one coat of approved acrylic wall primer and two coats of premium quality Acrylic Emulsion Distemper of approved shade and make, applied through airless spray machine (mechanical means) and finished with roller as required to obtain a smooth, uniform and durable finish, concrete all as specified and directed by Engr-in-Charge.Note: Application of primer and acrylic emulsion Distemper shall be carried out through airless spray machine (mechanical means) only. |
| 76 | M&L for preparation of old plastered/decorated surfaces and applying minimum 1.0 mm thick white wall care putty to achieve an even, smooth and uniform surface, including rubbing, cleaning and all necessary surface preparation and applying one coat of approved acrylic wall primer and two coats of premium quality Acrylic Emulsion Distemper of approved shade and make, applied through airless spray machine (mechanical means) and finished with roller as required to obtain a smooth, uniform and durable finish, concrete all as specified and directed by Engr-in-Charge.Note: Application of primer and acrylic emulsion Distemper shall be carried out through airless spray machine (mechanical means) only. Please Enable Macros to View BoQ information |
| 77 | M&L for preparation of old plastered/decorated surfaces and applying minimum 1.0 mm thick white wall care putty to achieve an even, smooth and uniform surface, including rubbing, cleaning and all necessary surface preparation and applying one coat of approved acrylic wall primer and two coats of premium quality Acrylic Emulsion Distemper of approved shade and make, applied through airless spray machine (mechanical means) and finished with roller as required to obtain a smooth, uniform and durable finish, concrete all as specified and directed by Engr-in-Charge.Note: Application of primer and acrylic emulsion Distemper shall be carried out through airless spray machine (mechanical means) only. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 15, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysJul 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender