Tender For Special Repair Of Offrs Mess Bldg No P-06 At Nagtalao Under Ge Banar
Tender Value
48.55 Lakhs
Estimated cost
Bid Submission
13 Jul 2026
4 days left
EMD
97116
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jodhpur → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair Of Offrs Mess Bldg No P-06 At Nagtalao Under Ge Banar- 1 Demolition Of Cement Concrete In Ground Floors And Pavings N.Exc 15 Cm Thickness Below Or Above Ground Level) And Removing Debris Out Of Mod Land Complete All As Specified. 2 Demolition Of Cement Concrete In Any Description And Any Position Not Otherwise Specifically Provided For And Removing Debris Out Of Mod Land Complete All As Specified. 3 M&L For 25 Mm Thick Cement Concrete Type B-1 1:2:4 (Using 20Mm Graded Crushed Stone Aggregate) To Receive Floor Finishes Etc Complete All As Specified. 4 M&L For 18-20Mm Thick Granite (Of Any Type) Work (Table Rubbed And Polished) In Steps, Jambs, Pillars, Window-Cills, Cooking Platforms And Like In Cement Mortar (1:4) Including Pointing In White Cement (1:2) Using Marble Dust With Admixture Of Pigment To Match With Shade Of Granite Complete All As Specified. 5 M&L Of 20-25Mm Thick Machine Cut Kota Stone Slab As In Shelves (Single Piece) Fixed In Walls Machine Cut, Laid Over Cement And Jointed With Grey Cement Slurry With Pigment To Match The Shade Of The Slab, Incl Rubbing And Mirror Polishing Complete All As Specified. 6 Provide And Lay Machine Cut Sand Stone Slabs Of Thickness 7.5 Cm In Sun Shades, Chajjas, Shelves, Cills, Landing, Coverstones, Templets,Etc. N Exc 2M In Length Punched Dressed On Face And Along Exposed Edges, Self Faced On Other Side And Set And Pointed In Lime Mortar 1:2 Or Cement Mortar 1:4 Complete All As Specified. 7 Dismantling Floor, Hearth Or Wall Tiling Including Cement Mortar Bedding, Removing Serviceable Tiles To Store And Rubbish Off The Premises Complete All As Specified.
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of Cement concrete in ground floors and pavings n.exc 15 cm thickness below or above ground level) and removing debris out of MOD land complete all as specified. |
| 2 | Demolition of Cement concrete in any description and any position not otherwise specifically provided for and removing debris out of MOD land complete all as specified. |
| 3 | M&L for 25 mm thick cement concrete type B-1 1:2:4 (using 20mm graded crushed stone aggregate) to receive floor finishes etc complete all as specified. |
| 4 | M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified. |
| 5 | M&L of 20-25mm thick machine cut KOTA stone slab as in shelves (Single piece) fixed in walls machine cut, laid over cement and jointed with grey cement slurry with pigment to match the shade of the slab, incl rubbing and Mirror polishing complete all as specified. |
| 6 | Provide and lay Machine cut sand stone slabs of thickness 7.5 cm in sun shades, chajjas, shelves, cills, landing, coverstones, templets,etc. n exc 2m in length punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4 complete all as specified. |
| 7 | Dismantling floor, hearth or wall tiling including cement mortar bedding, removing serviceable tiles to store and rubbish off the premises complete all as specified. |
| 8 | Dismantling of Stone slabs and tiles of any description or thickness laid ,bedded and pointed in any mortar in floors, aprons etc complete all as specified. |
| 9 | M&L for kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and including 15mm thick screed bed in CM (1:6 complete all as specified. |
| 10 | M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed 15 mm thick CM (1:6) and jointed with pigment to match the shade of the slab including rubbing and polishing complete all as specified. |
| 11 | M&L for coloured glazed ceramic tiles 350x 250x 7 mm/ 450X 350X 7mm thick as per IS 13712 Grade II(a) over 15mm thick rendering in CM (1:6) set and jointed in neat cement slurry and pointed with colour cement to match on vertical surfaces as in dado (colour and pattern as approved by GE) complete all as specified. |
| 12 | M&L for Light shade Virified Ceramic double charge tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. over 15mm thick rendering in CM (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified. |
| 13 | All as item as per Ser No 12.00 above but as in skirting including 10mm thick backing coat in CM 1:4 complete all as specified. |
| 14 | M&L for Non skid Ceramic tiles 7 to 8 mm thick (white), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15mm thick screed bed in CM (1:6) complete all as specified. |
| 15 | Taking down cement or cement lime plaster,any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified. |
| 16 | M&L for 10 mm thick rendering in CM 1:6 on stone masonry finished even and smooth without using extra cement complete all as specified. |
| 17 | M&L Rendering 5 mm thick in CM (1:3) on concrete surfaces on ceiling / facia /RCC Chhaja etc all as directed & finished even & smooth complete all as specified. |
| 18 | M&L for 15 mm thick rendering in CM 1:4 on stone masonry finished even and smooth without using extra cement complete all as specified. |
| 19 | Preparing old surfaces plastered or unplastered by Complete removal of existing treatment on walls complete all as specified. |
| 20 | M&L for three coats of white wash of new surfaces on walls complete all as specified. |
| 21 | M&L preparation of plastered or unplastered surface and applying three coats of white wash of new surfaces as on ceilings complete all as specified. |
| 22 | M&L Preparing old surfaces plastered or unplastered by Washing, rubbing down and stopping of distempered and painted surfaces as on ceilings and applying two coat of white wash complete all as specified. |
| 23 | M&L for two coat of oil bound distemper on plastered or unplastered on wall over 2 mm of wall care putty to prepare surface even and smooth complete all as specified. |
| 24 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm incl preparation over new surface/old surface complete all as specified. |
| 25 | M&L for two coat of oil bound distemper on plastered on wall over 2 mm of wall care putty over new plastered surface to prepare surface even and smooth complete all as specified. |
| 26 | Taking down chowkat with shutters (without taking off shutter from frame) size area n.exc 1.50 sqm each complete all as specified. |
| 27 | Taking down chowkat with shutters (without taking off shutter from frame) size area exc 1.5sqm but n.exc 4.0 sqm each complete all as specified. |
| 28 | Taking down steel windows / ventilator with frame of any description and any size complete all as specified. |
| 29 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 30 | S&F powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified. Note-Glass shall be measured and paid for separately. |
| 31 | S&F powder coated Anodised aluminium window and ventilator shutters(Thickness of powder coating not less than 50 micron), side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as per drg No CEJZ/TD/62/2015 Sh 1/1 & CEJZ/TD/63 Sh 1/3 to Sh 3/3. Note-Glass shall be measured and paid for separately. |
| 32 | S&F Anodised aluminium powder coated decogrill for doors, windows ventilators with one or more rebates including joining cleat for fixing etc complete all as specified. |
| 33 | S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, decorative face veneer with lipping/frame to match on both sides complete all as specified. |
| 34 | S&F 35 mm thick Glazed and skeleton shutters, made of 1 st class hardwood , open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed. |
| 35 | Pressed steel frames of size 125x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified. |
| 36 | S&F 5.5mm thick Sheet glass ordinary quality with solar control film of 25 micron reflective type sticked with glass as per manufacturer instruction and glazing in square n exc 0.50 Sqm size in each pane complete all as specified. |
| 37 | S&F 5.5mm thick Sheet glass ordinary quality with solar control film of 25 micron reflective type sticked with glass as per manufacturer instruction and glazing in square exc 0.50 Sqm size in each pane complete all as specified. |
| 38 | S&F in repair Mild steel wire cloth. but 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples complete all as specified. |
| 39 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified.(Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 40 | S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified. |
| 41 | S &F of Stainless steel butt hinges medium weight, cold rolled of size 100 mm size complete all as specified. |
| 42 | S&F in repair 200 mm long aluminium anodised tower bolt complete all as specified. |
| 43 | S&F in repair 150mm long aluminium anodised handle extruded section complete all as specified. |
| 44 | S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified. |
| 45 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified. |
| 46 | M&L for Cement Concrete type D-2 (1:4:8)( using 40mm graded aggregate) in fdn, filling and mass concrete complete all as specified. |
| 47 | S&F Fe-410-W (Gde E-250) quality-A rolled steel sections/hollow sections as in main and cross beams, purlins, where connected to common rafters and running rails fixed with angle cleats or other connecting plates complete all as specified. |
| 48 | Dismanteling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified. |
| 49 | Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified. |
| 50 | S&F Hard drawn steel wire fabric (weight per Sqm N.exc 4 Kg/sqm)cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcemnt complete all as specified. |
| 51 | M&L for preparing new steel surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red-oxide primer complete all as specified. |
| 52 | Taking up or down GI steel water tubing 15 mm bore and connection, including cleaning for refixing or remove to site complete all as specified. |
| 53 | Taking up or down GI tubing 20 mm bore and connection, including cleaning for refixing or remove to site complete all as specified. |
| 54 | Supply & Fixing 15mm bore GI Tubes, 'medium grade' galvanised,with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified. |
| 55 | Supply & Fixing 20mm bore GI Tubes, 'medium grade' galvanised,with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified. |
| 56 | Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting n exc 10 cm girth complete all as specified. |
| 57 | S&F in repair of bib cock 15mm dia, cast copper alloy fancy type chromium plated, screwed for iron pipe or for brass ferrule complete all as specified. Make-CERA/JAQUAR or Equivalent |
| 58 | S&F in repair Pillar taps 15mm bore , cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe .Make-CERA/JAQUAR or Equivalent |
| 59 | S&F in repair 15 mm dia bore Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified. Make-CERA/JAQUAR or Equivalent |
| 60 | S&F in repair Fancy type Chromium plated shower roses 125mm size with arm, with or without swivel joints, 15mm bore, including fixing to steel pipe or union complete all as specified. |
| 61 | S&F in repairs angular stop valves cast copper alloy chromium plated(ISI marked) screwed down high pressure fancy type screwed both ends for 15mm bore of iron pipe or union complete all as specified. Make-CERA/JAQUAR or Equivalent |
| 62 | S&F 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair complete all as specified. |
| 63 | S&F 15mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair complete all as specified. |
| 64 | S&F looking mirror (borderless) (Brand-I) fancy type fixed with suitable number of stainless steel cup screws (Minimum 4 Nos) complete all as specified. |
| 65 | M&L for 75mm outlet diameter UPVC nahani trap, with CP Mild steel grating (with or without hole) including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) using 20mm graded stone aggregate complete all as specified. |
| 66 | S&F in repair tubular towel rail 20mm dia brass chromium plated `D' type 60cm long with bracket and fixed complete all as specified. |
| 67 | S&F in repairs decorative type curtain rod stainless steel finish of pipe 22 to 25 mm dia with best quality knob metal with double fitting type including stainless steel brackets fixed to walls complete with two nos decorative stainless steel knobs at each end (As approved by Engr -in-charge). |
| 68 | S&F in repair vitreous china wash down water closet (Pedestal pattern EWC) one piece, coloured, floor mounted coupled closet, including connection to drain (or outgoing pipe), anti-sypohonage pipe etc, with & including WC seat cover coloured closed pattern with flat bottom and cover, vitreous china symphonic action type twin flush flushing cistern of 10 litre capacity with lid, necessary fittings complete all as specified and directed.Make-CERA/JAQUAR or Equivalent |
| 69 | Dismantling of cast iron/pvc soil waste & vent pipes 100/110 mm dia incl all fittings etc complete. |
| 70 | Dismantling of cast iron/pvc soil waste & vent pipes 75 mm dia incl all fittings etc complete. |
| 71 | Supplying and laying of 75 mm dia PVC pipes SWR & Plain PVC SDR 11 fittings in trenches complete all as specified. |
| 72 | Supplying and laying of 110 mm dia PVC pipes SWR & Plain PVC SDR 11 fittings in trenches complete all as specified. |
| 73 | Supplying and laying of 75 mm dia PVC pipes SWR fittings on walls / ceiling or laying in floors complete all as specified. |
| 74 | Supplying and laying of 110 mm dia PVC pipes SWR fittings on walls / ceiling or laying in floors complete all as specified. |
| 75 | S&F 75 mm bore PVC bends any radius with oval acess door complete all as specified. |
| 76 | S&F 110 mm bore PVC bends any radius with oval acess door complete all as specified. |
| 77 | S&F for 100mm dia PVC cowls, diminishing pieces or tapers (larger bore measured) |
| 78 | Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified. |
| 79 | S&F powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified (min thickness of powder coating 50 micron) complete all as specified. |
| 80 | S&F 32mm bore low or high density polyethylene waste pipes (LDPE) of pressure rating 6Kg/Sqm fixed complete to walls, ceiling or floors etc complete all as specified. |
| 81 | S&F in repair 15mm bore PVC connection 600mm long best quality with PTMT nuts complete all as specified. |
| 82 | S&F in repair Kitchen sink without drainage board made of stainless steel 1mm thick with plug, washers and waste Including bedding in cement mortar or Including fixing cantilever brackets and connecting union to pipe overall size 495mmx420mm & bowl size 410mm x 330mm x 160mm including brass waste coupling, PVC waste pipe complete all as specified. |
| 83 | S&F in repair Kitchen sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including brass waste coupling, PVC waste pipe complete all as specified. |
| 84 | S & F in repair Vitreous China wash basin, white, flat back, size 550x450mm but including brackets and PTMT waste coupling 32 mm size complete all as specified. |
| 85 | S & F in repair Vitreous China Half stall urinal white (minimum), with waste coupling 32 mm size and union for discharge pipe complete all as specified. |
| 86 | M&L 70 mm thick PCC (1:2:4) type B1 using 20mm graded stone aggregate as in floor , hard standing flooring finished even and smooth without using extra cement complete all as specified. |
| 87 | M&L 50 mm thick PCC (1:3:6) type C1 using 20mm graded stone aggregate as in plinth protection finished complete including forming joints in 2 mtr interval and filled with bitumen mastic all as specified. |
| 88 | M&L for roof treatement in the following stages :-(a) Applying evenly a coat of bituminous primer conforming to IS-3384 @ 0.40 ltr per sqm over and including 10 mm thick cement mortoar (1:4) and surfaces finished even and smooth without using extra cement all as specified . (b) Second coat of blown type bitumen confirming to IS 702-1988 grade 85/25 @ 1.2 Kg/Sqm . (c) Third layer of APP modified polmeric membrane centre core of 20 micron HMHDPE outer film 20 micron both sides, thickness 3.00 mm having weight 2.25 Kg/Sqm. (d) Fourth coat of blown type bitumen confirming to IS 702-1988 grade 85/25 @ 1.2 Kg per Sqm. (e) 40 mm thick PCC padding in cement concrete 1:2:4 (12.5 mm graded aggregate ) finishing even or smooth or applying PCC tile 20cmx20 cm over 15 mm thick CM(1:6) screed bed. Incl Taking down existing roof treatment in any postion and any thickness on RCC roof slab and debries to be disposed out of MOD land |
| 89 | Dismantling water tanks of capacity exc 500 litre but n exc 1000 litre and removing to store complete all as specified. |
| 90 | S&F in replacement rotational moulded polyethylene water storage tank ISI Marked (cylindrical vertical with closed top) white, hoisted and fixed in position all as directed of capacity 1000 ltrs a Including 20mm bore brass ball valve high pressure with polythene float complete all as specified. |
| 91 | Supply only integral water proofing compound (ISI marked). |
| 92 | Demolition of stone masonry /block walling built in cement mortar |
| 93 | M&L for squarred rubble walling Jodhpur type regular coursed well bonded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified. |
| 94 | Extra over squared rubble stone walling Jodhpur type regular course for hammer dressing to face of stone with max depression on face from a straight edge not exc 20mm and dressing complete all as specified. |
| 95 | M&L for precast cement concrete solid building blocks type B1 1:2:4 (20mm graded stone aggregate) or slabs 10cm thick (with plain or interlocking joints as directed) setting in 1:4 cement mortar, complete, in walls complete all as specified. |
| 96 | M&L for taking down and removal of loose / disintegrated old concrete / plaster and applying 10mm thick bonding coat of modified styrene butadiene emulsion (SBR Bonding agent i.e. Nitobond SBR 45) in proportion 1 (Nitobond SBR 45) : 1(water) : 3 (OPC) by volume with the brushes etc to bind New Cement plaster/ polymer Modified plaster/ concrete/ screed concrete with old surface etc complete. |
| 97 | M&L applying 15mm thick plaster with polymer modified mortar fortified with SBR (Nitobond SBR 45 ) in proportion 1:3 by weight 5 litres Nit bond SBR 45 to added to 50 KG Cement with 13 litre water addition, finished surface to match with existing adjoining surface of ceiling, beams and alike complete all as specified. |
| 98 | M&L and applying two or more coats of 2 component zinc based epoxy rust preventer (Nitozinc Primer-M) on corroded reinforcement after cleaning and removing the rust from corroded reinforcement with the help of wire brush and treating it with rust remover (Reebaklens RR) including thoroughly cleaning washing air blowing brushing etc complete all as specified. Make : Dr. Fixit or equivalent.Note : Qty of Zinc based epoxy rust prevent or only shall be taken into account for payment purpose on the basis of actual consumption. |
| 99 | M&L for MS Props erecting for temporary supports to structural members like beams, slabs,etc to relieve the load on the members during breaking of damaged concrete, removal guniting,excavation or any dismantling work as per instruction of Engineer-in-charge. These supports shall be provided either in the form of props or trestles fabricated using structural steel as per site requirements. |
| 100 | M&L for chipping of exposed surface of reinforced cement concrete slab/columns/beams/chajjas/parapet/roof projection/balcony/staircase and removing loose concrete particles with chisel hammer without impact on concrete surface , clean the surface by sand blasting using river sand with minimum of 6 kg pressure at the nozzle or air blower by mechanical compressor ,cleaning the exposed reinforecement with wire brushes etc and disposal of debris including all scaffolding , machinery ,tools etc all complete all as specified |
| 101 | M&L for cleaning &applying rust remover (CICO Clean-o rust) in two coats over rusted reinforcement surface including providing anti corrosive coating with two component epoxy based zinc rich primer/Rust passivation Inhibitor coat at the rate of 6-8 sq. mtr/ltr not less than 50 microns thickness with CICO ZINCILATE-500 or equivalent to reinforcement surface as per manufacturer's instructions including all scaffolding , machinery, tools tackles complete all as specified. Make: CICO clean-dust- or equivalent. |
| 102 | M& L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, inciuding cranking, bending spiraly for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.Note: Additional Reinforcement wil be provided, if the diameter of corroded steel bar is less than 30% of the original diameter,12mm dia bars shal be provided as main reinforcement to the required length with proper development length and tie them to theprefixed shear connectors so that the additional rebar acts monolithically with the existing ones and core concrete. |
| 103 | M&L for Mild steel TMT bars 5 mm dia and over upto and Including 10mm da in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dla or securing with clips complete all as specified. Note : Additional Relinforcement: In the case of the shear relnforcement also, If the diameter of the rebars are reduced, provide 8mm dla stirups in the form of 2 \\"U\\" shaped bars, Tle them properly so that it has a tight contact with the main bars. |
| 104 | M&L for Shear Connectors by drilling 12mm dia holes up to a maximum depth of 75mm and fixing 8mm dia L shaped anchor may rods be. as shear connectors at every 300mm c/c on the surfaces of the columns/beams or any other structural member as the case may be.Clean the same using air or blower and make sure that there are no fine particles present in the hole and filled the holes and anchoring two component styrene & cement free epoxy- acrylate fixing and anchoring compound. At this stage push the shear connector gently in to the hole and finish the excess resin which comes equivalent the shear connectors not to be disturbed for Minimum 20 minutes Make: CICO RESIFIX-G or equivalent in Fosroc lokfix/Hilti and Master bullder (BASF) Note: Reinforcement shall be paid separately under item ser no above |
| 105 | M&L for new steel or rebars by drilling holes with 10 mm to 20mm dia and 100 to 200mm deep as per lS code of 10D formula and filling the holes after inserting of reinforcement dia 8 to 16mm for anchioring at ends/shear connector and filled the holes with one or two component styrene free vinylester resin anchor or two components, styrene & cement free epoxy- acrylate fixing and anchoring compound ( having the technical parameters mentioned in material specifications) using standard sealant applicator gun after drilling holes of required diameter at required locations, for holding /fixing/ placing in position the steel mesh reinforcement at desired level /stretching complete all as specified. (Note: Steel reinforcement shall be paid and measured separately). Make: CICO RESIFIX-G or equivalent. |
| 106 | M&L for use of waste providing leak proof steel shuttering in any position cut to length and providing runners supports as per manufacturer's instructions, including all necessary scaffolding, machinery, tools tackles etc complete al as specified. |
| 107 | M&L for providing Micro concrete with CICO MICROCRETE at the rate of 25kg per 0.0125 m3 with 20% properly graded 5mm to 10mm silt free aggregate as per manufacturer instructions and mixing concrete with mechanically electrically operated mixer machine etc all as specified.Make: CICO MICROCRETE of CICO Technalogies Itd or equivalent. |
| 108 | S&F SS Soap Dish complete all as specified. |
| 109 | S&F as in repairs stainless steel plate rack of size 30\\"x24\\"x10\\" size as per trade pattern fabricated with 0.50mm thick stainless steel sheet suitable for stacking 15 plates with hooks /fittings complete all as per sample kept in GE's office . |
| 110 | Writing letters or figures (Black Roman, Italic or Indian n. exc 30cm high with thick paint complete all as specified |
| 111 | Excavation in trenches not exc 1.50m wide and not exc 1.50m depth and getting out in soft/loose soil ext complete all as specified. |
| 112 | S&F for 75mm thick steel fibre reinforced (SFRC) man hole/ drain cover with iron frames (medium) complying to the standard specifications as mentioned in the IS 12592 BIS Standard, minimum load bearing capacity 5 ton/sqm, in square, rectangular or circular shape complete all as specified. |
| 113 | Demolition and breaking up drain pipes 150 mm dia (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified. |
| 114 | S&F 150mm Reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified. |
| 115 | M&L for cement concrete (1:3:6) type C-2, using 40mm graded stone aggregate bed to drain pipe 150 mm dia including packing under and hunching against the pipe after they are laid including necessary formwork complete all as specified. |
| 116 | Returning, filing in including, lelveling,watering and well ramming in layers not exc 25cm thick each complete all as specified. |
| 117 | Removing excavated material (soil) to a distance not exc 50m depositing where directed at a level not exc 1.5m above the starting point complete all as specified. |
| 118 | Taking out from position framed woodwork as in cupboards/cabinets etc with all fittings ,shutters, shelves, drawers etc in any position fixed in walls or floors & removal of the rubbish outside MD land all as directed by Engg-in-charge for overall sizes exc 0.50 sqm but nexc 1.50 sqm & depth nexc 60 cm complete all as specified. |
| 119 | Supplying and fixing in repair factory made PVC shutter of 18 mm thickness consisting of panel of 18 mm thick celluca ply of density 600 Kg.cbm density with prelaminated sheet on one side cut in desired size of shutter and fixed with frame as in cabinet boxes with shelf and shutter full size fitted above the kitchen cooking platform and/or other platform including all necessary fittings and fixtures like nickle plated clip hinges, knobs, channels etc including dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.Note : Items like cupboard knobs, stainless steel channel, CP plate clip hinges are included in the mentioned rates and as per manufacturesrs specification and drawing.The measured area shall be front elevation. |
| 120 | Supplying and fixing in repair factory made PVC shutter of 18 mm thickness consisting of panel of 18 mm thick celluca ply of density 600 Kg.cbm density manufactured by an ISO 9000 certified company using for shutter celluca ply 18 mm thick cut in desired size of shutter and fixed with frame of kitchen accesory/cubboard at all four edges of shutter using 13/6 size self tapping steel screws. below cooking platform The thickness of the shutter is edfe painted by matching colour of PVC ink of plain colour of PVC sheet using complete all as specified and directed by Engineer-in-Charge and manufacturers specification. Note : Items like cupboard knobs, stainless steel channel, CP plate clip hinges are included in the mentioned rates and as per manufacturesrs specification and drawing.The measured area shall be front elevation. |
| 121 | Providing and fixing polyvinyl chloride (PVC) sheet frame of width 150 mm & 18 mm thickness made out of extruded 18mm PVC sheet and joined with suitable Cement Solvent adhesive and screw.The frame shall be fixed to the wall using 75mm long M.S. Screws through the frame by using PVC fasteners. A minimum of 3nos. of screws to be provided for each vertical member & minimum 2nos. for horizontal member etc. complete as per manufacturers specification and direction of Engineer-in-Charge. |
| 122 | M&L for stainless steel tray incl suitable length slider both side( Grade 304) of required size , on the top of floor or the side of waist slab with suitable arrangement complete all as specified . |
| 123 | S&F Readymade Jodhpur stone Chatri (2m height and 1.1m dia) complete all as specified. Please Enable Macros to View BoQ information |
| 124 | S&F Readymade Jodhpur stone Chatri (2m height and 1.1m dia) complete all as specified. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 23, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysJul 15, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender