|
| 1 | Item Rate BoQ BoQ_Ver3.0 Item Rate Normal INR Only INR Select, Excess (+), Less (-) Less (-) Tender Inviting Authority: GE Utilities Udhampur Name of Work: Repair/Maint of automation system and allied works for water supply systemunder GE (Utilities) Udhampur. Contract No: GE/U-76/2026-27 Bidder Name : PRICE SCHEDULE(This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only ) NUMBER # TEXT # TEXT # NUMBER # TEXT # NUMBER NUMBER TEXT TEXT # NUMBER # TEXT# TEXT # NUMBER # NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER # NUMBER # TEXT TEXT NUMBER # NUMBER # DATE NUMBER # NUMBER # TEXT # Ser.No. Item Description Item Code / Make Quantity Units Estimated Rate Addition / Deduction Addition / Deduction Values Currency Convertion against each Item Quoted Currency in INR / Other Currency BASIC RATE In Figures To be entered by the Bidder Rs. P Excise Duty VAT Freight Charges ( Unloading & Stacking) Any Other Taxes/Duties/Levies Other Taxes 2 IIIrd Party i.e DGS&D / RITES etc Inspection Charges @0.34%+Service Tax Less for Cenvat Credit,if any respect of Supplies Under full Excise Duty Category TOTAL AMOUNT Without Taxes TOTAL AMOUNT TOTAL AMOUNT In Words |
| 2 | Reinstallation, testing and commissioning and reprogramming of Master Control Station(SCADA Software). The services includes programming & installation of SCADA Software for B- Reservoir Pump House. The scope includes:-Services for programming, configuration and customisation of the Smart Station Platform with respect to the Water supply Module as per actual site conditions and requirement of the engineer. (a). Landing Page to depict criritcal paramters viz. - Level of water in all tanks, Pump status ON/OFF/FAIL, Motorized butterfly valve status START/STOP/FAIL, Solenoid valve status ON/OFF/FAIL, Pressure transmitter status.(b). Creation of drop down tabs to monitor the all Pump houses and Remote PLC Panel systems individually.(c). Creation of individual PLC Panel wise schematics and layouts for the Water Supply system as per the actual site including display of all relevant parameters viz. Level of water in all tanks, Pump status ON/OFF/FAIL, Motorized butterfly valve status START/STOP/FAIL, Solenoid valve status ON/OFF/FAIL, Pressure transmitter status.(d). Soft keys for remote manual operation of all pumps and motorised valves from the Master Control station. |
| 3 | (e). Creation of Day wise Reports for :-(i) Run hours of pumps(ii) Pump / valve operation failures(iii) Active/Return status of each equipment with date and time.(iv). Configuring notifications, alerts and alarms as per preset logic. (v) Consumption Patterns - Daily, Weekly, Monthly and Annually. Note: - 1). Any changes to the SCADA software, e.g. Changes in report format, changes in operational screens, creation of soft keys etc. shall be carried out by authorized representative of M/s Universal Switch Gear Control. The technician shall submit a letter from the manufacturer as proof of his being a authorized representative of the manufacturer. 2). The contractor has to submit the MOU from OEM in the technical bid itself, failing of the same will lead to rejection of bid in Technical Evaluation of Tender Bid. The successful bidder has to submit a Memorandum of Understanding (MoU) from OEM (i.e. M/s Universal Switch Gear Control) in a non-judicial stamp paper of Rs 10.00 duly notorised with an undertaking stating that execution of all SCADA related items of work shall be carried out under technical support and guidance of OEM. |
| 4 | Supply, Installation, Programming,Testing and Commissioning of wireless communication modem that’s suitable for existing PLC Panel. Network type 5G/4G, Supports all types of M2M SIMs, Two Serial Ports for RS232 and RS485 for external device interface, LED indicators provide network information, Supports MODBUS/RTU, Data transfer protocol to remote server via TCP/IP, Cellular Interface Standards: GSM/GPRS/EDGE/UMTS/ HSPA/FDD LTE, GPRS/EDGE: 850/900/1800/1900 MHz, Power supply : 24 V DC, Operating temperature: -20 deg to 60 deg, complete all as specified and directed by Engr-in-Charge. Make : Ascom, Maestro, MCom, Niseva, Nomus and Data Bridge |
| 5 | Supply, Installation, Reprogramming,Testing and Commissioning of HMI that’s suitable for existing PLC Panel - Touch screen, TFT 7” Colour Liquid crystal display, Display character 16-dot standard font: 50 characters x 30 rows (two-byte characters), Display colour more then 10k, 32-level brightness, Built in interface with RS 232, RS485/422, Ethernet, USB, SD card, Internal Flash memory 15MB, Input power supply voltage 24VDC(+10% -15%) Ripple voltage 200mV or less, operating temperature :0 deg to 50 deg / storage temperature : -20 deg to 60 deg, complete all as specified and directed by Engr-in-Charge. Make :Unitronics / Mitsubishi /Renu |
| 6 | Reprogramming of PLC base Panel and Integrate, Modification of the program & Creation of soft keys to facilitate remote monitoring and operation of the Automaton PLC base Panel incorporated at Filteration and Jackwell Pump House.The scope of work includes modification of the SCADA (Water Supply) system and its formats so as to include the status of the said Automation Slave Panels in the SCADA software, complete all as specified and directed by Engr-in-Charge. |
| 7 | Supply, Installation, Testing, Commissioning and Programming of Omni or Bi Directional Parabolic antenna with control station to generate strong directional effect with WLAN network support having mast mounting arrangment. Control station should operate on license free frequency with necessary hardware at a suitable location to be connected to the central scada server so as to establish connectivity with every station of the network after conducting a frequency survey of the entire area of interest and identify suitable locations to mount the station hardware and the height of the antennas to establish clear line of sight either directly or by multi hop so as to be able to send data.Antenna type:- Omni or Bi Directional Parabolic antennaFrequency Range - 2402-2472MHz 0r 5150-5970MHz as per site requirement. Peak Gain:- 17dBi or 25 dBi as per site requirement. Degree of protection:- IP55, complete all as specified and directed by Engr-in-Charge.Note:-Rate quoted is deemed to be included for making arrangemets of accessories such as mounting bracket and mast clips.Make of Item - Siemens / Schneider Electric / Cambium Networks/ Phoenix Contact |
| 8 | Supply, Installation, Testing, Commissioning 2 KVA UPS / INVERTER with smart battery management system with maintenance free Batteries for powering the panel for a minimum of 30 minutes in case of supply failure.UPS should have following features, complete all as specified and directed by Engr-in-Charge.:-Charger:- Build in solid state three stage recharge.Display:- LED DisplayOutput: - Pure Sine WaveProtection:- EMI, RFI, Surge, Spike & Overload.Communication: - RS232 Audible Alarm:- Main Failure Alarm, Battery Low Alarm, UPS Warning, Fault.(Make: APC / TATA LIEBERT / NUMERIC / CYBERPOWER) |
| 9 | Supply, Installation, Testing and Commissioning SMPS unit suitable for out put 24 volt of rating 3 Amp as per exiting sample/ size, complete all as specified and directed by Engr-in-Charge. Make: Schneider/NHP or equivalent make |
| 10 | Supply, Installation, Testing and Commissioning of buzzer system with base electrical connector as per existing size/type, complete all as specified and directed by Engr-in-Charge. Make - Mimic or equivalent make |
| 11 | Supply, Installation, Testing and Commissioning of relay pin type 4C/O , 220 -240Volt AC or as per exiting sample/ model no RU4S-A220, complete all as specified and directed by Engr-in-Charge. Make : LEONE / IDEC/L&T/Schneider |
| 12 | Supply, Installation, Testing and Commissioning of relay pin type 4C/O , 24 Volt DC or as per exiting sample/ model no RU4S-D24, complete all as specified and directed by Engr-in-Charge. Make : LEONE / IDEC/L&T/Schneider |
| 13 | Supply, Installation, Testing and Commissioning of indicator lamps of colour red / green as per exiting sample/ size, complete all as specified and directed by Engr-in-Charge. Make : ESBEE / Schneider /L&T or equivalent make |
| 14 | Supply, installation, testing, and commissioning of float type Point Level Sensor for PVC tank with the following specification:- Type:- Magnetic Magnet:- Ring Type Switch:- Reed Switch Connecting cable:- 2 core Teflon Make : Siemens / Nohken / USGC |
| 15 | Supply, Installation, Testing and Commissioning of 3 way selector switch for operation of Auto/ Manual system complete as per existing size/type and suitable for operation of scada automation slave panel, complete all as specified and directed by Engr-in-charge Make - Mimic or equivalent make |
| 16 | Supply, Installation, Testing and Commissioning of push button lamps of colour red / green as per exiting sample/ siz, complete all as specified and directed by Engr-in-Charge. Make : ESBEE / Schneider /L&T or equivalent make |
| 17 | Supply and fixing in replacement of rust proof, maintenance free magnetic float switch / water level sensor as per exiting sample/ size, complete all as specified and directed by Engr-in-Charge. Make :RDS/ATS or equivalent make |
| 18 | Supply, installation, testing, and commissioning of Pressure Transmitter with proper wiring including necessary power pack for supply of DC :-Power supply : 9-34 V DCEnclosure : IP 65Temperature : -40 to 80 CelsiusAccuracy : Maximum 1 %Pressure Range : 0 - 40 barOutput Signal : 4-20 mAResponse Time : 4 ms Make of Item - Danfoss/Endress+Hauser/Indfoss/Honeywell |
| 19 | Supply, Installation, Testing and commissioning of Air releasing solenoid valve having 10 mm dia, 230 V AC operated coil , complete all as specified and directed by Engineer in charge. {Cost of Fixing Accessories of Solenoid Valve (GI Pipe, Bend, etc) included}Make: ROTEX / AVCON / ASCO / Uflow |
| 20 | Supply, installation, testing, and commissioning of Solenoid Valve 12 mm dia 230 V AC, stainless steel body, direct acting / diaphragm type, pilot operated Solenoid Valve for Air Release with manual bypass arrangement along with all necessary installation accessories like gate valve, barrel piece, double nipple, elbows/bends etc with following specification:- (a) Size:- 12mm(b) Designed line pressure:- 0.5 to 10 bar (c) Body Material:- Stainless Steel(d) Coil Power:- 6WMake : Samson SED / Avcon / Rotex |
| 21 | Supply and fixed in replacement of defected/ burn out /unsafe internal control wiring and connection for automation main master panel or automation slave panel as per existing system and including using by FR PVC insulated electric wire with copper conductor wiring having of single core of size 0.5 sqmm to 1.0 sqmm sub wiring as properly electrical connection for smooth controlling panel of scada system including resetting of system, complete and testing all as specifed and directed by Engr-in-charge |
| 22 | Supply and fixing in replacement of water level controller relay card 5 Levels type as per exiting sample/ size, complete all as specified and directed by Engr-in-Charge. |
| 23 | Supply, Installation Testing & Commissioning of Indoor type PLC ( Programmable Logic Controller) based Pump and Valve Automation, Protection Panel with Wirelesss Radio Frequency based Communication suitable for control and monitoring of 04 Nos. Centrifugal Pumps (100HP), 15 Nos. Motorized Butterfly Valve, 04 Nos. Pressure Transmitter, 01 Nos. Ultrasonic Sensor, 04 Nos. Solenoid Priming Valve, 04 Nos. Solenoid Air Release Valve, 02 Nos. Float Sensor. The panel should be of minimum size 1500(H) X 1100(W) X 300(D) mm fabricated from 2 mm CRCA Sheet. (Location :- B-Reservoir Pump House) The Panel should comprise the following items:- (a) Water Level Sensing & Display(b) Automatic Pump On/Off (c) Automatic Operation of Motor Actuated Butterfly Valves (d) Single Phasing Prevention (e) Manual Mode Operation (all connected sub systems including all valves in pump houses and pumps) from the PLC based Control Panel.(ii) 01 No. PLC with follwing specifications:- (MAKE:- SCHNEIDER/L&T/GE AUTOMATION/PHOENIX CONTACT)(a). 1 Nos. Ethernet communication port.(b). Suitable No. of digital / analog input and outputs. |
| 24 | (c). Programming Software based on IEC to facilitate building of custom build function blocks.(d). Industrial Grade Processor, Web Server, SMTP E-mail service.(e). Protocol : Master/Slave Modbus, Expandable upto 248 I/O’s and 7 expansion module. (iii) 01 No. HMI - 7\\" Graphical Touch screen display (MAKE:- ROCKWELL AUTOMATION/L&T/GE AUTOMATION/SCHNEIDER) (a). 01 No. RS 485 and 01 No. USB port (b). Serial multilink, USB downloading port (c). Support external data storage on a USB memory stick for storing production data and backing up applications(iv) 01 No. SMPS of 5A rating suitable according to panel design. (Make: SCHNEIDER / TTPL/ PHOENIX CONTACT / DELTA)(v) Suitable No. of interposing relays of 220VAC & 24 VDC coil rating and 6 A contact rating. (Make: OEN / OMRON / SALZER /PHOENIX CONTACT) (vi) Suitable No. of relay cards with operating voltage 24VDC, with continuous current of 5A. Card must be of 8 channel & having 8 relays.( UL / ELMAX/ TTPL /PHOENIX CONTACT) (vii) MCB rating 32A & 6A as suitable according to panel design. (Make:- L&T/ Schneider/ABB/LS) |
| 25 | (viii) Illuminiated push button, Indicator lamp, Selector switches as suitable according to panel design. (Make:- Schneider/ESBEE/ABB) (ix) Audio visual alarm indicator as suitable according to panel design. (Make:- Schneider/ L&T /Autonics/Jigo) CRCA Enclosure:- Make (UNIVERSAL SWITCH GEAR CONTROL / HOFFMAN / ADLEC / TRICOLITE ) Make of the PLC based panel:- (Universal Switch Gear Control / Adlec / Tricolite / GE Automation / Rockwell Automation )Note: - Note: - The Programming, Testing, Commissioning & Integration of PLC Panel shall be carried out by authorized system integrator of the OEM of PLC (i.e. Schneider/GE Automation/Phoenix Contact/Lauritz Knudsen) . The programmer shall submit a letter from the OEM of PLC i.e. Ecostructure Expert Certificate / Integrated Solution Provider Certificate as proof of his being an authorized system integrator of the OEM. |
| 26 | Supply, Installation Testing & Commissioning of Indoor type PLC ( Programmable Logic Controller) based Pump and Valve Automation, Protection Panel with Wirelesss Radio Frequency based Communication suitable for control and monitoring of 03 Nos. Centrifugal Pumps (75HP & 50HP), 04 Nos. Motorized Butterfly Valve, 03 Nos. Pressure Transmitter, 02 Nos. Ultrasonic Sensor, 03 Nos. Solenoid Priming Valve, 03 Nos. Solenoid Air Release Valve, 02 Nos. Float Sensor. The panel should be of minimum size 1200(H) X 800(W) X 300(D) mm fabricated from 2 mm CRCA Sheet. (Location :- B-Reservoir Pump House) The Panel should comprise the following items:- (a) Water Level Sensing & Display(b) Automatic Pump On/Off (c) Automatic Operation of Motor Actuated Butterfly Valves (d) Single Phasing Prevention (e) Manual Mode Operation (all connected sub systems including all valves in pump houses and pumps) from the PLC based Control Panel.(ii) 01 No. PLC with follwing specifications:- (MAKE:- SCHNEIDER/L&T/GE AUTOMATION/PHOENIX CONTACT)(a). 1 Nos. Ethernet communication port.(b). Suitable No. of digital / analog input and outputs. |
| 27 | (c). Programming Software based on IEC to facilitate building of custom build function blocks.(d). Industrial Grade Processor, Web Server, SMTP E-mail service.(e). Protocol : Master/Slave Modbus, Expandable upto 248 I/O’s and 7 expansion module. (iii) 01 No. HMI - 7\\" Graphical Touch screen display (MAKE:- ROCKWELL AUTOMATION/L&T/GE AUTOMATION/SCHNEIDER) (a). 01 No. RS 485 and 01 No. USB port (b). Serial multilink, USB downloading port (c). Support external data storage on a USB memory stick for storing production data and backing up applications(iv) 01 No. SMPS of 5A rating suitable according to panel design. (Make: SCHNEIDER / TTPL/ PHOENIX CONTACT / DELTA)(v) Suitable No. of interposing relays of 220VAC & 24 VDC coil rating and 6 A contact rating. (Make: OEN / OMRON / SALZER /PHOENIX CONTACT) (vi) Suitable No. of relay cards with operating voltage 24VDC, with continuous current of 5A. Card must be of 8 channel & having 8 relays.( UL / ELMAX/ TTPL /PHOENIX CONTACT) (vii) MCB rating 32A & 6A as suitable according to panel design. (Make:- L&T/ Schneider/ABB/LS) |
| 28 | (viii) Illuminiated push button, Indicator lamp, Selector switches as suitable according to panel design. (Make:- Schneider/ESBEE/ABB) (ix) Audio visual alarm indicator as suitable according to panel design. (Make:- Schneider/ L&T /Autonics/Jigo) CRCA Enclosure:- Make (UNIVERSAL SWITCH GEAR CONTROL / HOFFMAN / ADLEC / TRICOLITE ) Make of the PLC based panel:- (Universal Switch Gear Control / Adlec / Tricolite / GE Automation / Rockwell Automation )Note: - Note: - The Programming, Testing, Commissioning & Integration of PLC Panel shall be carried out by authorized system integrator of the OEM of PLC (i.e. Schneider/GE Automation/Phoenix Contact/Lauritz Knudsen) . The programmer shall submit a letter from the OEM of PLC i.e. Ecostructure Expert Certificate / Integrated Solution Provider Certificate as proof of his being an authorized system integrator of the OEM. |
| 29 | Supply, Installation, Testing and Commissioning of Ultrasonic Level sensor with following specifications: Supply Voltage and Current:10 to 30 V dc (10% maximum ripple),100 mA max at 10 V, 40 mA max at 30 V (exclusive of load), Sensing Range:200 mm to 5 m,Ultrasonic Frequency:75 kHz burst, rep. rate 96 ms, Delay at Power-up:1.5 seconds,Analog Output (Voltage Sourcing: 0 to 10 V dc),Minimum Load Resistance = 500 ohms,Minimum Required Supply Voltage for Full 0-10 V Output Span = (1000/RLoad + 13) V dc, Analog Output: (Current Sourcing: 4 to 20 mA),Maximum Load Resistance = 1 kΩ or ( Vsupply/0.02 - 5) ohms, whichever is lower, Minimum required supply voltage for full 4-20 mA output span = 10 V dc or [(RLoad × 0.02) + 5] V dc, whichever is greater.4 to 20 mA output calibrated at 25 °C with a 250 Ω load, Temperature: Uncompensated: 0.2% of distance/°C,Compensated: 0.02% of distance/°C, complete all as specified and directed by Engr-in-Charge. Make:Banner / Endress+Hauser / Siemens Note: - 1). The Ultrasonic Sensor need to be covered in a polycarbonate box of size 130X130X75 mm before installation on OHT or Sump.2). The Programming of Ultrasonic Sensor, e.g. Changes in range of sensor, changes in operational features etc. shall be carried out by authorized system integrator of the provided makes. |
| 30 | Supply, Installation, Testing and Commissioning of Ultrasonic Level sensor with following specifications: Supply Voltage and Current:10 to 30 V dc (10% maximum ripple),100 mA max at 10 V, 40 mA max at 30 V (exclusive of load), Sensing Range:200 mm to 5 m,Ultrasonic Frequency:75 kHz burst, rep. rate 96 ms, Delay at Power-up:1.5 seconds,Analog Output (Voltage Sourcing: 0 to 10 V dc),Minimum Load Resistance = 500 ohms,Minimum Required Supply Voltage for Full 0-10 V Output Span = (1000/RLoad + 13) V dc, Analog Output: (Current Sourcing: 4 to 20 mA),Maximum Load Resistance = 1 kΩ or ( Vsupply/0.02 - 5) ohms, whichever is lower, Minimum required supply voltage for full 4-20 mA output span = 10 V dc or [(RLoad × 0.02) + 5] V dc, whichever is greater.4 to 20 mA output calibrated at 25 °C with a 250 Ω load, Temperature: Uncompensated: 0.2% of distance/°C,Compensated: 0.02% of distance/°C, complete all as specified and directed by Engr-in-Charge. Make:Banner / Endress+Hauser / Siemens Note: - 1). The Ultrasonic Sensor need to be covered in a polycarbonate box of size 130X130X75 mm before installation on OHT or Sump.2). The Programming of Ultrasonic Sensor, e.g. Changes in range of sensor, changes in operational features etc. shall be carried out by authorized system integrator of the provided makes. |
| 31 | Supply, installation, testing, and commissioning of Solenoid Valve 25 mm dia 230 V AC, stainless steel body, direct acting / diaphragm type, pilot operated Solenoid Valve for Priming of pump with manual bypass arrangement along with all necessary installation accessories like gate valve, barrel piece, double nipple, elbows/bends etc with following specification:- (a) Size:- 25mm(b) Designed line pressure:- 0.5 to 10 bar (c) Body Material:- Stainless Steel (d) Coil Power:- 6WMake : Samson SED / Avcon / Rotex |
| 32 | Supply, Installation, testing and Commissioning of 80 mm dia, single phase, Motor Actuated Butterfly valve with disc material SS - 304, Stem Material SS - 410, Seat EPDM, hand wheel for manual operation and having 05 nos. limit switches for Open / Close condition, valve position indicator and over ride trip. The housing of actuator should be of Aluminium Dicast. The actuator must have planetary gear set to transfer the largest torque in the most compact form. The mounting shall be direct on valve type.Input Voltage : 230V AC Designed Line Pressure : 16 kg/sq cm.Gear Set Type : Planetary Gear SetIn built CPU:- Quad-core 64-bit ARM Cortex A53 clocked at 1.2 GHzInbuilt 4 USB 2 portsIn built Base Ethernet PortIn built Micro SD port for loading your operating system and storing data In built wireless LAN and Bluetooth Low EnergyThe mounting shall be direct type using specialized arrangement of GI pipe of suitable size/thickness, complete all as specified and directed by Engr-in-Charge. |
| 33 | Note - 1). Wiring & Testing of Mototrized Butterfly Valve shall be carried out by authorized system integrator of the provided makes. Make of Actuator - SAMSON / UNIVERSAL SWITCH GEAR CONTROL / EMERSON / ROTORK / AUMAMake of Butterfly - L&T / AUDCO |
| 34 | Supply, Installation, testing and Commissioning of 100 mm dia, single phase, Motor Actuated Butterfly valve with disc material SS - 304, Stem Material SS - 410, Seat EPDM, hand wheel for manual operation and having 05 nos. limit switches for Open / Close condition, valve position indicator and over ride trip. The housing of actuator should be of Aluminium Dicast. The actuator must have planetary gear set to transfer the largest torque in the most compact form. The mounting shall be direct on valve type.Input Voltage : 230V AC Designed Line Pressure : 16 kg/sq cm.Gear Set Type : Planetary Gear SetIn built CPU:- Quad-core 64-bit ARM Cortex A53 clocked at 1.2 GHzInbuilt 4 USB 2 portsIn built Base Ethernet PortIn built Micro SD port for loading your operating system and storing data In built wireless LAN and Bluetooth Low EnergyThe mounting shall be direct type using specialized arrangement of GI pipe of suitable size/thickness, complete all as specified and directed by Engr-in-Charge. |
| 35 | Note - 1). Wiring & Testing of Mototrized Butterfly Valve shall be carried out by authorized system integrator of the provided makes. Make of Actuator - SAMSON / UNIVERSAL SWITCH GEAR CONTROL / EMERSON / ROTORK / AUMAMake of Butterfly - L&T / AUDCO |
| 36 | Supply, Installation, testing and Commissioning of 150 mm dia, single phase, Motor Actuated Butterfly valve with disc material SS - 304, Stem Material SS - 410, Seat EPDM, hand wheel for manual operation and having 05 nos. limit switches for Open / Close condition, valve position indicator and over ride trip. The housing of actuator should be of Aluminium Dicast. The actuator must have planetary gear set to transfer the largest torque in the most compact form. The mounting shall be direct on valve type.Input Voltage : 230V AC Designed Line Pressure : 16 kg/sq cm.Gear Set Type : Planetary Gear SetIn built CPU:- Quad-core 64-bit ARM Cortex A53 clocked at 1.2 GHzInbuilt 4 USB 2 portsIn built Base Ethernet PortIn built Micro SD port for loading your operating system and storing data In built wireless LAN and Bluetooth Low EnergyThe mounting shall be direct type using specialized arrangement of GI pipe of suitable size/thickness, complete all as specified and directed by Engr-in-Charge. |
| 37 | Note - 1). Wiring & Testing of Mototrized Butterfly Valve shall be carried out by authorized system integrator of the provided makes. Make of Actuator - SAMSON / UNIVERSAL SWITCH GEAR CONTROL / EMERSON / ROTORK / AUMAMake of Butterfly - L&T / AUDCO |
| 38 | Supply, Installation, testing and Commissioning of 150 mm dia, single phase, Motor Actuated Butterfly valve with disc material SS - 304, Stem Material SS - 410, Seat EPDM, hand wheel for manual operation and having 05 nos. limit switches for Open / Close condition, valve position indicator and over ride trip. The housing of actuator should be of Aluminium Dicast. The actuator must have planetary gear set to transfer the largest torque in the most compact form. The mounting shall be direct on valve type.Input Voltage : 230V AC Designed Line Pressure : 16 kg/sq cm.Gear Set Type : Planetary Gear SetIn built CPU:- Quad-core 64-bit ARM Cortex A53 clocked at 1.2 GHzInbuilt 4 USB 2 portsIn built Base Ethernet PortIn built Micro SD port for loading your operating system and storing data In built wireless LAN and Bluetooth Low EnergyThe mounting shall be direct type using specialized arrangement of GI pipe of suitable size/thickness, complete all as specified and directed by Engr-in-Charge. |
| 39 | Note - 1). Wiring & Testing of Mototrized Butterfly Valve shall be carried out by authorized system integrator of the provided makes. Make of Actuator - SAMSON / UNIVERSAL SWITCH GEAR CONTROL / EMERSON / ROTORK / AUMAMake of Butterfly - L&T / AUDCO |
| 40 | Supply, Installation, testing and Commissioning of 250 mm dia, single phase, Motor Actuated Butterfly valve with disc material SS - 304, Stem Material SS - 410, Seat EPDM, hand wheel for manual operation and having 05 nos. limit switches for Open / Close condition, valve position indicator and over ride trip. The housing of actuator should be of Aluminium Dicast. The actuator must have planetary gear set to transfer the largest torque in the most compact form. The mounting shall be direct on valve type.Input Voltage : 230V AC Designed Line Pressure : 16 kg/sq cm.Gear Set Type : Planetary Gear SetIn built CPU:- Quad-core 64-bit ARM Cortex A53 clocked at 1.2 GHzInbuilt 4 USB 2 portsIn built Base Ethernet PortIn built Micro SD port for loading your operating system and storing data In built wireless LAN and Bluetooth Low EnergyThe mounting shall be direct type using specialized arrangement of GI pipe of suitable size/thickness, complete all as specified and directed. |
| 41 | Note - 1). Wiring & Testing of Mototrized Butterfly Valve shall be carried out by authorized system integrator of the provided makes. Make of Actuator - SAMSON / UNIVERSAL SWITCH GEAR CONTROL / EMERSON / ROTORK / AUMAMake of Butterfly - L&T / AUDCO |
| 42 | Supply, Installation, testing and Commissioning of 300 mm dia, single phase, Motor Actuated Butterfly valve with disc material SS - 304, Stem Material SS - 410, Seat EPDM, hand wheel for manual operation and having 05 nos. limit switches for Open / Close condition, valve position indicator and over ride trip. The housing of actuator should be of Aluminium Dicast. The actuator must have planetary gear set to transfer the largest torque in the most compact form. The mounting shall be direct on valve type.Input Voltage : 230V AC Designed Line Pressure : 16 kg/sq cm.Gear Set Type : Planetary Gear SetIn built CPU:- Quad-core 64-bit ARM Cortex A53 clocked at 1.2 GHzInbuilt 4 USB 2 portsIn built Base Ethernet PortIn built Micro SD port for loading your operating system and storing data In built wireless LAN and Bluetooth Low EnergyThe mounting shall be direct type using specialized arrangement of GI pipe of suitable size/thickness, complete all as specified and directed by Engr-in-Charge. |
| 43 | Note - 1). Wiring & Testing of Mototrized Butterfly Valve shall be carried out by authorized system integrator of the provided makes. Make of Actuator - SAMSON / UNIVERSAL SWITCH GEAR CONTROL / EMERSON / ROTORK / AUMAMake of Butterfly - L&T / AUDCO |
| 44 | Supply, Installation, testing and Commissioning of Pole structure for installation and protection of RF Antennas having galvanised iron light grade pipe ( ISI marked ) with all fittings such as elbow, tee, reducer , coupling etc mounted on metal plate grouted in earth or on the roof top. The pole should be tied with steel wire rope from both the sides. The minimum height of the structure should be not less than 15 meter. The structure should be self supportive type with proper earthing, complete all as specified and directed by Engr-in-Charge. |
| 45 | Supply, Installation, Testing and Commissioning of 4 pair CAT 6 UTP Armoured cable for Communication.Make : D Link/ Finolex/ Polycab/ Havells/ Digisol |
| 46 | Supply, Laying/ Fixing on wall 6 core, 1.5 sqmm cross sectional area armoured copper conductor cables, 1100 volts grade heavy duty cable PVC insulated and PVc sheathed, laid in trenches/ laid under floor or fixed maked with walls / on poles/in ducts/in GI pipes etc, complete all as specified and directed by Engineer in charge. Make: Polycab/FSC/Torrent/Finolex . |
| 47 | Supply, Laying/ Fixing on wall 4 core, 1.5 sqmm cross sectional area armoured copper conductor cables, 1100 volts grade heavy duty cable PVC insulated and PVc sheathed, laid in trenches/ laid under floor or fixed maked with walls / on poles/in ducts/in GI pipes etc, complete all as specified and directed by Engineer- in- charge. Make: Polycab/FSC/Torrent/Finolex |
| 48 | Supply, Laying/ Fixing on wall 2 core, 1.5 sqmm cross sectional area armoured copper conductor cables, 1100 volts grade heavy duty cable PVC insulated and PVc sheathed, laid in trenches/ laid under floor or fixed maked with walls / on poles/in ducts/in GI pipes etc, complete all as specified and directed by Engineer- in- charge. Make: Polycab/FSC/Torrent/Finolex |
| 49 | Supply and fixing in replacement of 5 pair of 0.5 mm dia armoured copper cable suitable for sensoring with suitable size of PVC conduit pipe as per exiting sample/ size duly fixed on wall of over head tank, complete all as specified and directed by Engineer-in-charge. Make: Havells/Nicco/Plaza/Polycab or equivalent make |
| 50 | Supply and installed pre galvanised G.I. (GP Sheet) cable protection tray 400x50x50mm insize including all installation acessories used as per site, complete all as specified and directed by Engr-in-Charge. |
| 51 | Add : Supply, installation, testing, and commissioning of 32 Digital Input module card for Programmable Logic Controller with Transmission speed 500 kbps having Spring-cage connection, modular type and Process data operation with 2 words, Operating Voltage: - 24VDC, complete all as specified and directed by Engr-in-Charge.Make : ABB / Siemens / Phoenix Contact / Lauritz Knudsen |
| 52 | Supply, installation, testing, and commissioning of 04 Analog Input module card for Programmable Logic Controller with Transmission speed 500 kbps having Inline data jumper, modular type and 2-Conductor connection technology, Input Voltage Signal: - 0 V ... 10 V, -10 V ... 10 V, complete all as specified and directed by Engr-in-Charge.Make : ABB / Siemens / Phoenix Contact / Lauritz Knudsen |
| 53 | Supply, Installation, testing and Commissioning of 200 mm dia, single phase, Motor Actuated Butterfly valve with disc material SS - 304, Stem Material SS - 410, Seat EPDM, hand wheel for manual operation and having 05 nos. limit switches for Open / Close condition, valve position indicator and over ride trip. The housing of actuator should be of Aluminium Dicast. The actuator must have planetary gear set to transfer the largest torque in the most compact form. The mounting shall be direct on valve type.Input Voltage : 230V AC Designed Line Pressure : 16 kg/sq cm.Gear Set Type : Planetary Gear SetIn built CPU:- Quad-core 64-bit ARM Cortex A53 clocked at 1.2 GHzInbuilt 4 USB 2 portsIn built Base Ethernet PortIn built Micro SD port for loading your operating system and storing data In built wireless LAN and Bluetooth Low EnergyThe mounting shall be indirect type using specialized extended type arrangement of GI pipe of suitable size/thickness, so that actuator mounting is at least 12 inches above pipe level, complete all as specified and directed by Engr-in-Charge. |
| 54 | Note - 1). Wiring & Testing of Mototrized Butterfly Valve shall be carried out by authorized system integrator of the provided makes. Make of Actuator - SAMSON / UNIVERSAL SWITCH GEAR CONTROL / EMERSON / ROTORK / AUMAMake of Butterfly - L&T / AUDCO Make of Actuator - Astech/ Emtork/ Samson / Universal Switch Gear Control / Emerson / Rotork / AumaNote : Motor Actuated valve should be compatible with existing SCADA (All the functions of Motor Actuated Butterfly valve should be control remotely from existing SCADA) |
| 55 | Supply, Installation, testing and Commissioning of 250 mm dia, single phase, Motor Actuated Butterfly valve with disc material SS - 304, Stem Material SS - 410, Seat EPDM, hand wheel for manual operation and having 05 nos. limit switches for Open / Close condition, valve position indicator and over ride trip. The housing of actuator should be of Aluminium Dicast. The actuator must have planetary gear set to transfer the largest torque in the most compact form. The mounting shall be direct on valve type.Input Voltage : 230V AC Designed Line Pressure : 16 kg/sq cm.Gear Set Type : Planetary Gear SetIn built CPU:- Quad-core 64-bit ARM Cortex A53 clocked at 1.2 GHzInbuilt 4 USB 2 portsIn built Base Ethernet PortIn built Micro SD port for loading your operating system and storing data In built wireless LAN and Bluetooth Low EnergyThe mounting shall be indirect type using specialized extended type arrangement of GI pipe of suitable size/thickness, so that actuator mounting is at least 12 inches above pipe level, complete all as specified and directed by Engr-in-Charge. |
| 56 | Note - 1). Wiring & Testing of Mototrized Butterfly Valve shall be carried out by authorized system integrator of the provided makes. Make of Actuator - SAMSON / UNIVERSAL SWITCH GEAR CONTROL / EMERSON / ROTORK / AUMAMake of Butterfly - L&T / AUDCO Make of Actuator - Astech/ Emtork/ Samson / Universal Switch Gear Control / Emerson / Rotork / AumaNote : Motor Actuated valve should be compatible with existing SCADA (All the functions of Motor Actuated Butterfly valve should be control remotely from existing SCADA) |
| 57 | Supply and fixing water filter for raw water used for agriculture purpose made out of durable plastic or high density polyethelene for longevity,incorporates with features like disc filteration and antimcloging technoloigics,helix system for easy cleaning of dia 100mm pip, etc complete all as specified and directed by Engr-in-charge. Make:-Azud,Kent, Renuka or equivalent |
| 58 | Supply, installation, testing, and commissioning of PLC CPU Unit, complete all as specified and directed by Engr-in-Charge.(i) 01 No. PLC CPU Unit with Clock frequency 64 MHz, Program memory 512 kByte. (ii) 02 Nos. of Ethernet communication port.(iii) 08 Nos. Digital Input and 04 Nos. Digital Outputs.(iv) Programming software based on IEC 61131-3 to facilitate building of custom build function blocks.(v) It shall support integrated web server. (vi). Protocol : Modbus TCPIPMake : ABB / Siemens / Phoenix Contact / Lauritz Knudsen Total in Figures 0.0 0.0 INR Zero Only 4.0 Construction of chamber for 100mm sluice plates item5 10.0 Nos Quoted Rate in Figures Select 0.0 0.0 Zero Only Quoted Rate in Words INR Zero Only Please Enable Macros to View BoQ information |
