|
| 1 | BI PAINTS Thermoplastic Road Marking Paint White 251. Running Track Marking2. Football Ground Marking |
| 2 | Football Goal Post |
| 3 | PUTEX Nylon Stadium Box NetFootball Goal Post Net, Size 100millimeter |
| 4 | Earthwork in excavation Trenches in hard soil (vide classification of soil item -B) all complete as per approved design, building specification and direction of E/I |
| 5 | Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and |
| 6 | Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and |
| 7 | Granular sub-base/base/surface course with local materials (Table 400.13) by mix in place method normal Construction of granular sub-base by providing local material spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at once and compacting with smooth wheel roller to achieve the desired density complete as per Clause 401.4 as per Technical Specification Clause 408. |
| 8 | Providing coarse clean SAND FILLING in foundation trenches or plinth including ramming & watering in layers not exceeding |
| 9 | Providing designation 75B one BRICK FLAT SOILING joint filled with local sand including cost of watering taxes royalty all complete as per |
| 10 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size) |
| 11 | P.C.C- Providing and lying in position cement concrete of specified grade excluding the cost of centering and shutturing - All work up to Plinth Level 1:3:6 ( 1 Cement : 3 coarse sand ( zone-III) : 6 graded stone aggregate 20 mm nominal size ) |
| 12 | providing P.C.C M-150 WITH NOMINAL MIX (1:2:4)IN Foundation& Plinth with approved Quality of Ston metal grade-lll …do…E/I |
| 13 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2.4(1 Cement: 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)P.C.C in FOUNDATION |
| 14 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)R.C.C in foundation |
| 15 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete |
| 16 | Providing designation 75 Abrick work in C.M (1:6)in foundation and plinth with approved quality of clean coarse sand of F.M2 to 2.5 including providing 10mm thick morter joints , cost of screening materials , raking of joints to 15mm depth , curing taxes and royality all complete as per building specification and direction of E/l |
| 17 | Providing designation 75 B BRICK in C.M (1:6) in Superstructure-------do------- |
| 18 | Providing designation 100 A brick work with fly ash lime brick (FLAG)Confirming IS 12894-1990 (9\\"X4.5X3\\")in C.M (1:6)in superstructure with approve quality of clean coarse sand of F.M 2 to 2.5 including providing 10mm thick morter joints , cost of screening materials , raking out joints to 15mm depth , curing , taxes and royalty all complete as per building specification and direction of E/I |
| 19 | Providing designation 112 mm thick reinforced designation 100 a brick work with fly ash lime brick (FLAG)Confirming IS 12894-1990 (9\\"X4.5X3\\")in C.M (1:4)insuperstructure with approve quality of clean coarse sand of F.M 2 to 2.5 including the cost of screening carriage of , materials scaffolding , raking out joints to 15mm depth , curing , taxes and royalty(but excluding the cost of reinforcement ) all complete as per building specification and direction of E/I |
| 20 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 21 | Reinforced cement concrete works in beams, suspended floors, roofs having slope up to 15\\" landings, balconies, shelves, chajjas , Lintel, bands, plain window sills, staircase and spiral stair case above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcemewnt:1:1.5:3: 3 graded stone aggregate 20mm nominal size. |
| 22 | Providing R.C.C. M-200 with nominal mix of (1:1½:3) in columns with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position vibrating, skirting, curing, (but excluding the cost of reinforcement, taxes and royalty all complete job as per building specification and direction of E/I. |
| 23 | Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts |
| 24 | Centering and shuttering including strutting, propiping etc. and removal of form forRoof slab, etc. for mass concrete |
| 25 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 26 | Centering and shuttering including strutting, propping etc. and removal of form for Chajjas including edges |
| 27 | Reinforcement Bar in R.C.C. 20% Steel of 8 & mm |
| 28 | 50 % Steel of 10 mm |
| 29 | 30% Steel of 12&16 mm |
| 30 | Providing and fixing fan hook of 16 mm dia M.S bar 1 metre long bent to requried size and shape placed in position and fixed in R.C.C slab / beem at the time of casting all complete as per building specification and direction of E.I(where materials is not supplied by the deptt.) |
| 31 | Supplying fitting and fixing M.S grill made of 20 x 6 mm M.S flat as per approved design and drawing properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E.I(where materials is not supplied by the deptt.) |
| 32 | supplying , fitting and fixing M.S gril / RECTANGULAR PIPE made of 20x6cmm M.S. FLA asper approved design and drawing , and properly fabricated with joints continous fillet welded and finished smooth , carriage of grill to work site , hoisting as per building specification and direction of E / WHERE A MATERAIL is not supplied in by the deptt |
| 33 | Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centers and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification and direction of E/I. |
| 34 | Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface |
| 35 | Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly cost of scaffolding and taxes all complete as per building specification and direction of E/I. |
| 36 | Providing two coats of Synthetic ENAMEL PAINT of approved shade and mack and one coat of red oxide primer over NEW STEEL surface including cleaning the surface after removing dirt, scales, grease sand papering, including cost of scaffolding etc. all complete as per specification direction of E/I. |
| 37 | Supplying, fitting & fixing 35mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with aluminum fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I. |
| 38 | Supplying, fitting & fixing 35mm thick solid core type decorative Double leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with aluminum fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I. |
| 39 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 40 | Providing and fixing pressed steel door frames confirmig to IS: 4351 manufactured form commercial mild steel sheet of 1.25 mm thickness including hinges jomb, lock jamb, bead and if required angle threshold of mild |
| 41 | Supplying fitting and fixing 35mm thick solid core type non-decorative single leaf flush shutters In doors and window with black board core blended with high quality phenol format dehyde |
| 42 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm,made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm longbrackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mmM.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame.The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as permanufacturer’s specification and direction of Engineer- in-Charge.30mm thick factory made solid both side prelaminated panel PVC Chaukhat consisting of frame made out of M.S. tube 19 gauge |
| 43 | Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S.frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shallbe flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mmwide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the innerside to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mmshall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side ofthe panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail &bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed tothe styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, andjoined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to bestuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction ofEngineer-in-charge, manufacturer's specification & drawing. |
| 44 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS:733 and Is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top....Anodised aluminium |
| 45 | Providing and fixing glazaing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/neoprene gasket …..With float glass panes of 4.0mm thickness |
| 46 | Providing and fixing stainless steel ( Grade 304) railing made of Hollowtubes, channels, plates etc., including welding, grinding, buffing, polishingand making curvature (wherever required) and fitting the same withnecessary stainless steel nuts and bolts complete, i/c fixing the railingwith necessary accessories & stainless steel dash fasteners , stainlesssteel bolts etc., of required size, on the top of the floor or the side ofwaist slab with suitable arrangement as per approval of Engineer-incharge,(for payment purpose only weight of stainless steel membersshallbe considered excluding fixing accessories such as nuts, bolts,fastenersetc.). |
| 47 | Providing 6 mm thick cement plaster (1:4) in Celling with clean coarse sand of..do.. all complete as per building specification and direction of E/I . |
| 48 | Providing 12mm thick cement plaster (1:6) in WALL with materials--do-- complete job as per specification and direction of E/I. |
| 49 | Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I. |
| 50 | Providing and applying plaster of paris putty of 2 mm thickness overplastered surface to prepare the surface even and smooth complete. |
| 51 | Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by the rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I. |
| 52 | Providing two coats of snowcem of approved shade and make over a coat of cement primer over new surface including prepairing the plastered surface by rubbing smooth with sand paper scaffolding curing,taxes all complete as per building specification and direction of E.I |
| 53 | Providing two coats of Plastic emulsion paint of approved shade and make over a coat of cement primer over new surface wooden including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I. (OUTSIDE & INSIDE WALL) |
| 54 | Applying priming coat with ready mixed paint over a coat of primer of approved shade and mike over new wooden surface including preparing the surface after cleaning, removing dirt-do |
| 55 | Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm . |
| 56 | Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: '(a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design.(b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. '(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing. The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items. |
| 57 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified bythe manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such asWhite, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints withwhite cement and matching pigment etc., complete. |
| 58 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to bespecified by the manufacturer), of approved make, in all colours, shades except burgundy, bottlegreen, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados,over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with greycement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment ofmatching shade complete. |
| 59 | Providing and laying 20 mm , thick while kota stone slab flooring of approved quality over 19mm . thick base of lime mortar (1:1:1) (Lime putty: surkhi coarse sand) laid and joined with white cement slurry including rubbing and polishing ----do---- |
| 60 | Providing and laying 6 mm . precast white Glazed Tiles in walls over 12 mm . cement mortar (1:3) and jointed with grey cement slurry flush pointed with white cement including rubbing, polishing and cost of curing taxes , and royalty all complete as per building specification and direction and of E/I . |
| 61 | 30mm thick factory made soiled both side Prelaminated Panel PVC door shutter consisting of frame made out MS tube of 19 guage thickness as per your size . |
| 62 | Casement window double panels with French (False) Mullion with S.S. 304 fricction hinges as per size and wieght of sash,multi-point locking system,zinc alloy (zamak) power Coated handal Using R3 series with frame (55mm& above)x (45mm& above) & sash (55mm& above) x(65mm&above) & French (Flase) mullion (55mm& above) x(65mm&above). (Height upto 1.8m) |
| 63 | Providing 1.5 mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E.I |
| 64 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with sea; ring conforming to IS:5382, leaving 10mm gap for thermal expansion, Single socketed pipes |
| 65 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler - 110mm |
| 66 | Bend - 110mm |
| 67 | Shoe - 110mm |
| 68 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete 110 mm |
| 69 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honeycomb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m longcomplete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 70 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means overareas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including gettingout and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-incharge. |
| 71 | Extra for each subsequent lead upto 25M beyond the intial lead of 50M (Maximum upto 150M lead by head load) as per specification and direction of E/I.) |
| 72 | Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment). |
| 73 | Supply at Site Well Decayed Farm Yard Manure (Supply at site of work well decayed farm yard manure, from any available source, approved by the engineer in charge including screening and stacking) |
| 74 | Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge |
| 75 | Spreading of Sludge Farm Yard Manure or/and good Earth (Spreading of sludge farm yard manure or/ and good earth in required thickness (cost of sludge, farm- yard manure or/and good earth to be paid for separately)) |
| 76 | Grassing with ' Doobs' Grass (Grassing with 'Doobs' grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for moving including supplying good earth if needed) |
| 77 | Making Lawns including Ploughing and Dragging with 'Swagha' Breaking of Clod (Making lawns including ploughing and breaking of clod, removal of rubbish, dressing and supplying doobs grass roots and planting at 15 cm apart, including supplying and spreading of farm yard manure at rate of 0.18 cum per 100 sqm) |
| 78 | Maintenance of Lawns or Turfing of Slopes (Maintenance of lawns or Turfing of slopes (rough grassing) for a period of one year including watering etc) |
| 79 | Turfing Lawns with Fine Grassing including Ploughing, Dressing (Turfing lawns with fine grassing including ploughing, dressing including breaking of clods, removal of rubbish, dressing and supplying doobs grass roots at 10 cm apart, including supplying and spreading of farm yard manure at rate of0.6 cum per 100 sqm) |
| 80 | Compacting original ground supporting subgrade (Loosening of the ground upto a level of 500 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of table 300-2 for subgrade construction.) |
| 81 | Supplying and stacking of good eaeth at site including royalty and carriage up to 1 kg |
| 82 | Supplying and stacking of well decayed cow dung manure at site including loading unloading and carriage for 1km lead. |
| 83 | Fine dressing the trenched ground including breaking clods (40.0% area of total) |
| 84 | Spreding of sludge dump manure or / and good earth in required thickness including carriage thickness including carriage of materials for lead upto 500m and loading unloading and stacking as per direction of Engineer in charge (cost of sludge dump manure or/and good earth to be paid separately) (qty 5+7) |
| 85 | providing and fixing neelgiri /mexocan grass turgf with earth 50mmto 60mmthickness of existing ground prepared wirh propal level and ramming with required tools wooden (dhurmos )and than rolling the surface with light roller make the surface smooth and even ,watering with sprinkler . |
| 86 | Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days ar till the grass froms a thick lawn free from weeds and fit for mowing including supplying good earth if needed (the good earth shall be paid for separately). |
| 87 | Digging holes in ordidinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1by valume(2parts of stacked volume of earth after reduction by 20%:1part of stacked volume of manure after reduction by 8%)flooding with water ,dressing including removal of rubbish and surplus earth ,if any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separatly ) |
| 88 | Providing and disply of Araucaria cookie plant of 3 ' -3 1/2 ht . Straight. Fresh and healthy lush green leaves from bottom to top ,well development , in 12\\" E/ pots &as per direction of the officer - in charge. |
| 89 | Providing and displying of Areca Palm plant of ht 3 to 4' with 3-4 branch full of fresh and heathy leave well development in 10\\" E pots &as per direction of the officer - in charge. |
| 90 | Providing and disply of Croton Petra Bangalore plant of ht 3 to 4' with 3-4 branch full of fresh and heathy leave well development in 10\\" E pots &as per direction of the officer - in charge. |
| 91 | Providing and disply of Livistoa Palm plant having on3' ht moss 60 cm to 75cm distance, full of fresh and healthy leaves well development ,10\\" Earthen POTS & as per direction of the offocers -in charge. |
| 92 | Providing and disply of Raphis Palm plant having ht 75 cm to 90cm distance, full of fresh and healthy leaves well development ,10\\" E POTS & as per direction of the offocers -in charge. |
| 93 | Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site. (a) From 0.00 M to 50.00 M below G.L. |
| 94 | (b) From 51.0 M upto 150.00 M |
| 95 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.200 mm nominal size dia |
| 96 | Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by \\"V\\" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge |
| 97 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:200 mm dia |
| 98 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.200 mm clamp |
| 99 | Supplying submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump.Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages2 HP |
| 100 | Supplying Full automatic star selta starter to operate induction motor working on 415v 3phase 50hz with no coil. Over load element , On _OFF push buttom with necessary materials and connection to Supply etc complete starter with original sheel steel encloser as per 3914.F.A.S.D starter upto 10.0 H.P |
| 101 | 3 core PVC insulated PVC sheathed copper conductor flat submersible cable.Supplying , Flat flexible submersible cable with ,copper conductor , PVC insulated and PVC sheathed as IS:70983 Core 4 Sq mm |
| 102 | Supply fitting and fixing GI pipe 50 mm Dia (TATA or equivalent make) Medium Quaility as per IS:1239 ( part 01 ) 2004 |
| 103 | Supply of 12m High mast light in two section Construction S355 grade as per BS-EN 10 025 Top Dia 100mm, bottom dia 360mm, plate thickness 3mm, 20side Polygon, galvanisation as per BS EN ISO 1461, base plate dia 570mm, base plate thickness 25mm, GI single spike lightining protection, maximum wind speed 47m/switch 8nos foundation bolts of pcd 445mm TS 600/30mm dia/850mm long. Luminaries carraige: material for 40 NB ERW Class B- M.S Pipe. dia of carraige ring 450mm (ID) with 8 arm, welded, 2 sections having carraying capacity upto 12 luminaries. Trailing Cable : 5core 2.5sq.mm. PVC flexible copper conductor winch/power Tool : Double drum , SWL 350kg with 0.75HP 6 Pole single speed integral motor Rope: Grade AISI 304, 7/19 construction, dia 6mm BLC 1450x2 having 2 nos of continues rope. Aviation obstruction light : twin dome aviation obstruction lights LED type as required. (But excluding Feeder Pillar) |
| 104 | For 12 mtr. High Mast : ITC of the high mast and light fixture with thehelp of suitable tools and plants, wiring of luminaries with all wiringmaterial like PVC insulated PVC sheathed flexible cable of suitablecopper conductor lugs, MCB and all labour & construction of shallowfoundation with M25 grade concrete for the high mast considering safesoil bearing capacity of 10T/ mtrs sq. for 12 M High mast. |
| 105 | outdoor stand mounted feeder panel with 32amp TP&N,MCB income ,45 amp TP contactor automatic swiching of luminaries ,powetr tool control incomer ougoing terminal etc as reqd.(for high mast) |
| 106 | EPR insulated /PVC sheated copper conductor trailing cable 5 crore 2.5 sq.mm.(for high mast) |
| 107 | 6MM DIA stainless steel wire rope of bracking load capacity 2350kg*2 for mtr high mast. |
| 108 | winch /power tool for high mast of double drum |
| 109 | 2.0 hp ac motor with AC motor with forward and reverse motion for highmast |
| 110 | Twin dome avivation light for highmast |
| 111 | Earthing with G.I earth pipe 4.5 mtr long. 40 mm dia including accessories, and providing masony enclosure with cover plate having locking arrangment and watering pipe etc.with charcoal and salt as required. |
| 112 | Supply and election ofLED flood light 160w fixer (make) bajaj havell philips |
| 113 | Wiring for light point/fan point/exaust fan point / callbellpoint with 1.5sq.mm FRPVC insulated copper conductor single core cable in surface/recrssed PVC conduit,with piano type switch, phenolic laminated sheet, suitable size PVC/G.I. box etc.as. Group C |
| 114 | Group A |
| 115 | Group B |
| 116 | Power plug wiring in PVC conduit (2x4 sq.mm):-Power plug wiring in PVC conduit (2x4 sq.mm):-Wiring for light / power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surfface / recessed PVC conduit along with 1 Nos. 4 sq.mmFR PVC insulated copper conductor single core cable for loop earthing as requried. |
| 117 | Wiring for light / power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surfface / recessed PVC conduit along with 1 Nos. 4 sq.mmFR PVC insulated copper conductor single core cable for loop earthing as requried. 2x1.5 Sqmm + 1x1.5 sqmm earth wire (For 5/6A Plug Points) |
| 118 | 2x2.5 sq.mm + 1x2.5 sq.mm earth wire |
| 119 | 2x4.0 sq.mm + 1x4.5 sq.mm earth wire |
| 120 | 2x6.0 sq.mm + 1x6.0 sq.mm earth wire |
| 121 | S/V PVC/ G.I. boxes :-Supplying and fixing PVC/G.I box of following sizes on surface or in recessed with sutiable size of phenolic laminated sheet cover infront including painting etc as requried. S/V PVC/ G.I. boxes :- 72 mm x 146 mm x 48 mm deep / (4\\" x 7\\" ) |
| 122 | 210 mm x 206 mm x 48 mm deep / (10\\" x 12\\" ) |
| 123 | S/F light plug point with piano type accessories :Supplying and fixing sutiable size G.I./PVC box on surface or in recessed with phenolic laminited sheet cover in front including providing and fixing 5 pin , 5/6 amps socket outlet and 5/6 amps piano type switch connection , painting etc, as requried. |
| 124 | S/F light plug point with MODULAR type accessories :Supplying and fixing sutiable size G.I./PVC box on surface or in recessed with phenolic laminited sheet cover in front including providing and fixing 5 pin , 5/6 amps socket outlet and 5/6 amps piano type switch connection , painting etc, as requried. |
| 125 | S/F lpower plug point with MODULAR type accessoriesSupplying and fixing sutiable size G.I./PVC box on surface or in recessed with phenolic laminited sheet cover in front including providing and fixing 6 pin , 15/16 amps socket outlet and 15/16 amps piano type switch connection , painting etc, as requried.S/F lpower plug point with piano type accessories :- |
| 126 | S/F celling rose :- Supplying and fixing 2 pin 5 amp. Celling rose on the existing junction box/ wooen block including connection etc. as requried. S/F celling rose :- |
| 127 | S/S/F Batten holder :-Supplying and fixing battrn / angle holder including connection etc as requried. F Batten holder :- |
| 128 | ITC celling fan :- Installation, testing and commissioning of celling fan, including wiring the down rods of standerd leanth (upto 30 mm) with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc. as requried. |
| 129 | ITC Resitance type celling fan with regulator :- Installation, testing and commissioning of resitance type celling fan regulator , in existing switch box including connection with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable. earthing the regulator etc. as requried. |
| 130 | S/F rewireable double pole / TP&N switch disconnector:-Providing and fixing following capacity doble pole / TP&N sheet metal switch disconnector fuse unit in existing metal board with rewireable type fuses, including drilling holes in metal board, making connections, etc as requried. 32 amps, double pole |
| 131 | S/F S.P. MCB DB :Supplying and fixing following way single pole nutral , sheet, MCB dstribution board , 240 volts ,on surface/recess, complete with tinned copper busbar,nutralbusbar, earth bar,din bar, detachable gland plate,interconnection, phosphate and powder painted 8way,single door |
| 132 | 4way, Double door |
| 133 | S/F 'B'serise, s.p.MCB:-Suppling and fixing 6amps to 32 amps rating , 240 volts, 'B' series, miniature circuit breaker suitable for lighting and other loads of folling poles in the existing MCB DB complete with connections, testing and commissioning et. as requried. 6/32amps, single Pole,\\"B\\" serise |
| 134 | Suppling and fixing ,240 volts \\"C\\"serise miniature circuit breaker suitable for inductive loads of follong poles in the existing MCB DB complete with connections, testing and commisioning etc. as required . 6/32 amps, Single pole |
| 135 | 6/32 amps, SPN |
| 136 | 16/25 amps |
| 137 | P/F M.V. danger notice plate:-Providing and fixing M.V danger notice plate of 200mm x 150mm, made of mild steel, at least 2mm thick and vitreous enamelled white on both sides and with inscription in single red colour on front side as requried. |
| 138 | Earthing with copper plate 600mmx 600mmx 3mm thick including acessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal or cock and salt) complete etc. as required.(2 Nos. for Main Panel) |
| 139 | P/F 25 x 5mm copper earth strip in pipe :-Providing and fixing 25mmx5mm cpper earth strip in 40mm & 4.5Mtr long G.I.pipe for earth electrode etc. as required. |
| 140 | S/L 8 SWG copper wire in ground :- S/L 6 SWG G.I. wire in ground :- Supplying and laying 8 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including soldering etc. as required. |
| 141 | Supply 15/16W LED BULB |
| 142 | 1x28 watt T5 Tube Light with fitting |
| 143 | CEILING FAN 48 (1200MM) |
| 144 | ITC exhuast Fan upto 450mm sweep- |
| 145 | MV Cable laying up to 35 sq.mm in ground |
| 146 | MV Cable laying up to 35 sq.mm in ground |
| 147 | 1 or 2 module (78 mm x 78 mm x 45 mm) |
| 148 | 4/5 module (78 mm x 140 mm x 50 mm) |
| 149 | Supplying and fixing of following sizes of PVC conduit alongwith the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required for Tele, RJ45 Cat 6 data outlet for computer network. 25 mm |
| 150 | 5/6 amps,one way switch |
| 151 | 5/6 amps, 3 pin socket outlet |
| 152 | Supply and installation of P.V.C. over head water tank- ----all complete as per direction E/I. |
| 153 | Supply of G.I. pipes of Tata or any other ---------- all complete job as per direction of E/I. (i) 15mm dia |
| 154 | (ii) 20mm dia |
| 155 | (iii) 25mm dia |
| 156 | (iv) 32mm dia |
| 157 | Earth work in excavation ( as perI.S. 3114=1965 for laying of differenttypes and sizes of pipes --------------------------------------- as per direction of E/I. (a)For classification of oil item -B). Rs,34.40/cum |
| 158 | Earth work in back filling ----- all complete as per direction of E/I. Same as qty sl. No 76/12.1.1.1 |
| 159 | Providing and fixing male ended 15mm dia brass bib cock ---------all complete as per direction of E/I. |
| 160 | Providing and fixing brqass/C.I. stop cock of approved quality allcomplete as per specification and direction of E/I. (A)BRASS STOP COCK (a) 15mm dia. |
| 161 | Providing and fixing G.M. full way valve --------------------- all complete as per direction (C) 25mm dia weight not less than 1.5 kg. |
| 162 | (d) 32mm dia weight not less than 1.5 kg. |
| 163 | (f) 50mm dia weight not less than 1.5 kg. |
| 164 | Supplying fitting and fixing the following items complet with all material s as per direction of E/I. (b) (i) 600x450mm mirrors of 6mm thick., |
| 165 | ©(iii) C.P. brass soap dise contineer medium a good quality with screw and hinge etc. |
| 166 | cutting chajja or cornice for laying G.I. pipes---------------- all complete direction of E/I. |
| 167 | Making holes in walls for laying G.I. pipes---------------- all complete direction of E/I. (c) 375mm thick wall |
| 168 | Supplying fitting and fixing the following items complet with all material s as per direction of E/I. (b) (i) 600x450mm mirrors of 6mm thick., |
| 169 | supply materials labour for constraction of 600x600x90mm stop cock chamber of brick masonary. |
| 170 | Supplying fitting and fixing viterous waterland earth ware I.W..C or Tarry Hindustan or any other I.S.S. approved makewith 100mm H.C.I.'P' trap15litress.1. orcopull andlet go flushing ------------- all complete as per direction of E/I. (A) 580mm long width 1.2.5 liters low ©12.5 lit low level P.V.C. cisterns |
| 171 | Supplying fitting and fixing vierous white glazed eathan ware Indian Squating size 600mmx350mm urinal plate ----------------------- all complete as per direction of E/I. (A) Flat back or standing corner (600mm x 350mm) size (large) |
| 172 | Supplying fitting and fixing viteriouswhite glazed earthan ware wash hand basin ---------------------------------all complete as per direction of E/I. |
| 173 | Providing and laying 25 mm thick white makrana marble tiles in risers of step skirting and pillars of approved quality over 12 mm thick base of cement mortar (1:3) and jointed with white cement slurry --do --wall partition for Urinal .6M*.40M=.240m2x2nos |
| 174 | Carriage of Materials STEEL (15 km (p)) |
| 175 | CEMENT (15 km (p)) |
| 176 | SAND (19 km (p) + 1 km (k)) |
| 177 | CHIPS (14 km (p) + 1 km (k)) |
| 178 | BRICK (14 km (p) + 1 km (k)) |
| 179 | Fly Ash brick (5 km (p) + 1 km (k)) |
| 180 | MOORUM 2 km (p) + 1 km (k)) |
| 181 | Earth (4 km (p) + 1 km (k)) |
| 182 | Earth ( 1 km (k)) |
| 183 | GST @ 18% |
| 184 | Labour cess @ 1% Please Enable Macros to View BoQ information |
