Tender For Special Repair To Bldg No G-03 In Od Complex Under Ge (East) Mathura
Tender Value
92.91 Lakhs
Estimated cost
Bid Submission
20 Jul 2026
17 days left
EMD
1.64 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Mathura → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Bldg No G-03 In Od Complex Under Ge (East) Mathura
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chowkhats or frames not exc. 1.5 sq m each with shutters (without taking off shutters from the frames), complete all as specified & directed. |
| 2 | Taking down chowkhats or frames exc 1.5 sqm but not exc 4 sqm each with shutters of any description (without taking off shutters from the frames) complete all as specified & directed. |
| 3 | S&F factory made pressed steel frame for doors of size 125x60mm fabricated out & 1.25 mm thick sheet with one or more rebates including necessary fixing lungs, hinges, lock strike plate, etc, including PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate filling in chowkhats complete all as specified and as directed. |
| 4 | S&F factory made pressed steel frame for doors of size 105x60mm fabricated out & 1.25 mm thick sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, including PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate filling in chowkhats complete all as specified and as directed. |
| 5 | M&L for 35 mm thick factory made flush shutters, solid core construction with block board core and plywood face panels, both face covered with decorative face veneer with lipping/frame to match fixed with suitable adhesive, including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and directed. |
| 6 | S&F for 35 mm thick factory made second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (with sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and as directed. |
| 7 | S&F 100 mm long stainless steel hinge, type B-21, complete all as specified & directed. |
| 8 | S&F 200 mm long aluminium anodised barrel tower bolts of extruded sections complete all as specified & directed. |
| 9 | S&F 150 mm long aluminium handles fabricated type complete all as specified & directed. |
| 10 | S&F 250 mm long aluminium alloy sliding door bolt , bolt type and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed. |
| 11 | S&F 300 mm, mild Steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed. |
| 12 | S&F mild steel framed work such as MS gate, grills, gratings, MS sheet etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified & directed. |
| 13 | S&F factory made box type steel window with side hung shutters both glazed and guaged shutter frame 60 x 25 mm ERW hollow 'P' section with wall thickness not less than 1 mm fixed to pressed steel frame 120 mm x 70 mm x 1.6 mm thick including fixing glazed portion, iron grills 8mm square MS Bar hinges with steel handle and fittings lugs, tower bolt and steel peg stay etc complete with glazing bars, dovetailed or welded complete with cooler opening all as specified complete all as directed by Engineer-in-Charge. Refer CEJZ Drg No TD/2004/93 sheet No 1 /3 to 3/3 |
| 14 | Supply & fix 3mm thick sheet glass panes ordinary quality n.exc 0.50 sqm each fixed to steel frame complete oil putty in square including steel pin complete all as specified and directed |
| 15 | S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or stainless steel wire staples complete all as specified & directed. |
| 16 | M&L for anti termite treatment the soil along with internal wall and floor junction/external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall, through approved applicator, as per manufacturer’s instruction complete all as specified and directed. |
| 17 | Dismantling of ceiling boards of any type and any thickness including cover fillets and timber frame work complete. |
| 18 | M&L for providing and fixing powder coated MS galvanised steel inter locking metal grid (snap grid for false ceiling) of size 605 mm x 605 mm in true horizontal level, fixed to angle iron truss with 2-3 mm GI wire with galvanised butterfly level clips for all heights complete all as specified and as directed. |
| 19 | M&L for 4 mm thick pre-painted designer non-asbestos fibre cement building board and fixed on false ceiling grid with screws and including 10 mm wide designer POP strip all round at the junction of wall and false ceiling complete all as specified and as directed by Engr-in-charge. |
| 20 | Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar including removing rubbish out of the MoD land, complete all as specified & directed. |
| 21 | M&L for machine cut 5 cm thick sand stone slab in sun shades, chajjas, shelves, cills, landings, cover stones, templates, plinth protection, etc., not exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in CM 1:4, complete all as specified and as directed. |
| 22 | M&L for 18-20 mm thick Black granite stone as in cooking platforms, floor, window/door cill etc & the likes complete laid over 15mm thick cement and sand mortar in CM 1:4 including rounding off corners, mirror polishing complete & providing necessary holes for gas pipe / water supply pipes etc complete all as specified and as directed. |
| 23 | M&L for machine cut Kota stone slab as in flooring 20-25mm thick and not less than 0.70 sqm in full length laid over and including 15mm thick screed bed in cement and sand mortar 1:6 and jointed with gray cement mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and as directed. |
| 24 | M&L for Kota stone slab 18-20 mm thick in riser of steps, skirting, dado and including pillar laid over and including 10mm thick backing coat in cement and sand mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of slab including making groove to curve skidness, rubbing and polishing complete all as specified & directed. |
| 25 | Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15cm thick, including removing rubbish outside of MoD land, complete all as specified & directed. |
| 26 | M&L for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and as directed. |
| 27 | M&L for 75mm thick Cement concrete (1:3:6) type C-1 using 20mm graded stone aggregate laid in panels not exc 3 m and providing grooves at corner finished cement concrete surface even and fair without using extra cement as in plinth protection laid in panels, complete all as specified & directed. |
| 28 | Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work including removing rubbish out of MoD land, complete all as specified & directed. |
| 29 | M&L for reinforced cement concrete nominal mix (1:2:4) type B1 (using 20mm graded stone aggregate) as in slab supported on wall and shelves etc complete all as specified & directed. |
| 30 | M&L for TMT bars 10 mm dia and over, cut to length bent to shape required including cranking bending ,spirally for hooping for column ,hooking ends and binding with and including MS wire annealed not less than 0.9mm dia, complete all as specified & directed. |
| 31 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), complete all as specified & directed. |
| 32 | Form work to edges of concrete flat, roof slabs, concrete railings, breaks in floors and similar works not exceeding 100mm wide for fair finished surfaces, complete all as specified & directed. |
| 33 | Demolition of Brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified & directed. |
| 34 | M&L for brick work with sub-class 'B' bricks, straight or curved on plan exc 6.0 metre mean radius as wall built in cement & sand mortar 1:6, complete all as specified and as directed. |
| 35 | M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed. |
| 36 | Taking down cement plaster on brick or stone walls, ceiling etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed. |
| 37 | M&L for rendering 15 mm thick on other than fair faces of brick work or stone masonry surfaces in cement plaster 1:4 mixed with water proofing compound as per manufacturer's instruction, finished even and fair on wall surfaces, complete all as specified and directed. |
| 38 | Supply only Liquid water proofing compound complete all as specified and directed. |
| 39 | M&L for rendering 10mm thick on fair faces of brick or concrete surfaces in CM 1:6, finished even and fair complete all as specified and directed. |
| 40 | M&L for preparation of new/old surface including complete removal and applying two coats of 100% premium acrylic exterior emulsion paint having VOC less than 50 gm/litre & excellent protection against UV, Alkali & Fungal resistance, exterior paint of required shade (Company Depot tinted) with silicon additives @ 1.43 litre/10 Sqm over and including 1-2 mm thick wall care putty and priming coat of exterior primer applied at 0.90 litre/10 Sqm over new surfaces upto triple storey with fully automatic airless spray machine of paint application having an electric motor of min 1 HP with a flow speed of min 1 ltr per min having pressure 3300 PSI. Allow 6-8 hours to dry the surface of both coat of paint to achieve excellent application with 5 years performance warranty from manufacturers and instruction complete using limited man power including scaffolding, trestles, ladders, cradles and necessary safety measures for upto triple storey buildings complete all as specified and directed. |
| 41 | M&L for complete removal of existing surface /new plaster surface and applying two coat of Oil bound distemper over a coat of primer & over a coat of 2 mm thick wall care putty on old plastered surface using airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 metre. The machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed. |
| 42 | M&L for preparation of new steel surfaces of any description, over 10cm in width or girth and applying two coats of synthetic enamel paint over and including a coat of red oxide or zinc chrome primer complete all as specified & directed. |
| 43 | M&L for preparation of old steel surfaces of any description, over 10cm in width or girth and applying two coats of synthetic enamel paint complete all as specified & directed. |
| 44 | M&L for preparation of new wooden surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. |
| 45 | M&L for preparation of old wooden surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed. |
| 46 | Dismantling timber scantlings 40 sq cm and over in section, in any position complete all as specified and as directed. |
| 47 | M&L for roof trusses (Framed) tubular hollow pipes crane gantries, rails and fastenings and heavy brackets framing (Hollow tubular section, beam, tee, angle, channel or flat section) FE-290 Gd-165 including distance pieces, cleats etc complete all as specified and directed. |
| 48 | S&F 18mm thick WPC board in cupboard shutter/kitchen cabinet with decorative laminated on one side & other side balancing white, fixed with necessary stainless steel drilling screws/Anchoring bolt along with modular handles, design and colour as approved by GE including dismantling of boards any type, complete all as specified and directed. |
| 49 | S&F stainless steel handles 100mm size for kitchen cabinet, cupboard shutters, pattern/design as approved by GE complete all as specified and as directed. |
| 50 | S&F 0 degree clip type self closing hinges for cabinets fixed with cadimum coated screws all as per sample complete all as specified and as directed. |
| 51 | Dismantling corrugated, semi-corrugated, etc., AC/MS sheets in roof covering of any type complete all as specified and directed by Engineer-in-Charge. |
| 52 | M&L for pre-painted galvalume aluminum zinc coating GI based corrugated/ semi corrugated steel sheet 0.60 mm thick of an colour having tensile strength of 550 Mpa (AZ-150) as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 53 | M&L for pre- painted galvalume aluminum zinc coating GI based plain steel sheeting, 0.60 mm thick of an colour having tensile strength of 550 Mpa (AZ-150) in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) complete all as specified and directed. |
| 54 | M&L for 1mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and as directed. |
| 55 | Surface excavation not exc 30cm deep and avg 15cm deep and getting out soft/ loose soil complete all as specified and directed by Engr-In-Charge. |
| 56 | M&L for 75 mm thick PCC 1:4:8 type D2 using 40mm graded crushed stone aggregate as in sub base, complete all as specified and directed. |
| 57 | Supply and laying 60mm thick factory made chamfered edge cement concrete interlocking paver block of M-30 grade confirming to IS 15658-2006 locally available with approved colour, design & pattern as in foot path, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over minimum 50 mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. |
| 58 | M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed by Engr-in-Charge. Please Enable Macros to View BoQ information |
| 59 | M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed by Engr-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 22, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 20, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysJul 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 24 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender