Tender For Providing Of Certain Rw And Mw Work At Mil Stn Sgnr
Tender Value
Ref. Documents
Estimated cost
Bid Submission
16 Jul 2026
4 days left
EMD
82980
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ganganagar → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Providing Of Certain Rw And Mw Work At Mil Stn Sgnr
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 06-Jul-2026 | Amendment in Critical Dates | Date | 16-Jul-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Excavating in post holes in soft/loose soil (or similar holes) each n exc 0.5 cum getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface complete all as specified and directed. |
| 2 | Excavation in trenches not exceeding 1.5 Mtr wide and not exceeding 1.50 Mtr in depth for foundation, etc., not exceeding 10 Sqm on plan in soft /loose soil; & getting out in any type of soil complete all as specified and directed. |
| 3 | Returning filling in including spreading, leveling watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed. |
| 4 | Removal of excavated material to a distance not exceeding 50m and deposited where directed at level not exceeding 1.5m above the starting point complete all as specified and directed. |
| 5 | M&L for PCC 1:4:8 type, D2 (usding 40mm graded stone agg) foundation filling and mass concrete complete all as specified and directed. |
| 6 | M&L PCC 1:3:6 (using 40mm graded stone aggregate) type C2, in foundation of posts and struts complete all as specified and directed. |
| 7 | M&L mild steel work i.e. Angle iron/flat iron as in post and struts in fencing including cutting tops to shape, drilling holes, notching for wire etc conforming to Fe-290 grade E-165 complete all as specified and directed. |
| 8 | S&F 10 mm dia MS round bar for fixing of chain link fencing with post complete all as specifies and directed. |
| 9 | M&L two coats of synthetic enamel over a coat of red oxide primer exc 10 cm width /girth on new steel surfaces including preparation of surfaces complete all as specified and directed. |
| 10 | Supply only chain link fencing galvanised mild steel hot dipped (IS -2721) of 4 mm dia of mesh size 100 x 100 mm complete all as specified and directed.Note : Weight of Chain link fencing shall be measured by BOO as detailed by Accepting Officer. |
| 11 | Fixing only of chain link fencing including above galvanised mild steel to any type of standard rails vision, straining bolts including provision of binding wire complete all as specified and directed. |
| 12 | S&F mild steel screw bolts (machine made) with hexagonal or square head at one end, screwed end to be fitted with washer and one hexagonal/ square nut not exceeding 5cm long complete all as specified and directed. |
| 13 | S & F for Rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces,etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc., to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing etc conforming to Fe-290 grade E-165 complete all as specified and directed. |
| 14 | M & L for demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed. |
| 15 | M&L for double charged, vitrified, stain & scratch resistant, joint free, premium quality coloured tiles 1200 X 600 mm and 7-8 mm thick, as in floors etc. in any pattern of light & dark tiles as approved, set and jointed adhesive of Sika (Ceram Grey) @ 5 Kg/sq.m and pointed in white or coloured cement to match, in floors etc. over & including 20 mm thick screed in cement mortar (1:4) over and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed. |
| 16 | M&L for double charged, vitrified, stain & scratch resistant, joint free, premium quality coloured tiles 1200 X 600 mm and 7-8 mm thick in any pattern of light & dark tiles as approved,on vertical surfaces such as in skirting/dado etc ,length of each unit not less than 1200 mm , set and jointed adhesive of Sika (Ceram Grey) @ 5 Kg/sq.m over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed. |
| 17 | Site Clearnance Clearance in soft/loose soil complete all as specified and directed. |
| 18 | S&F Hand rails, hlaf round or other stock section or core for wooden hand rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilled holes, notching for wire, etc flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveling etc. and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 19 | Rough finished form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC / PCC bands in walls horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed. |
| 20 | S&F Galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75mm spacin and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc as directed (each line wire to be measred) complete all as specified and directed. |
| 21 | M&L Brick work with subclass 'B' bricks, straight or curved on plan exc 6m mean radius, built in built in CM 1:6 complete all as specified and directed. |
| 22 | M&L Rendering 15mm thick on fair faces/other than fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and directed. |
| 23 | M&L preparation of newly plastered surfaces and applying two coat of cement base paint over one coat of alkali resistant primer on wall surfaces complete all as specified and directed. |
| 24 | M&L preparation of newly plastered surfaces and applying two coat of cement base paint over 3mm thick wall putty over one coat of alkali resistant primer on wall surfaces complete all as specified and directed. |
| 25 | M & L for form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work in flat for fair finished surface complete all as specified and directed. |
| 26 | M & L form work to side of pillars, posts, struts, piers, columns and stanchions for squre, rectangular or polygonal rough finished surfce complete all as specified and directed. |
| 27 | M&L Form work to sides and soffits of floor and roof Beam etc complete all as specified and directed. |
| 28 | M&L Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick (horizontal or sloping) complete all as specified and directed. |
| 29 | M&L for RCC Design mix M-25 (using 20mm graded aggregate ) as in foundation including raft, footings, foundation beams, plinth beam and the like complete all as specified and directed. |
| 30 | M&L for RCC Design mix M-25 (using 20mm graded aggregate ) as in Columns, pillas, piers, posts and struts complete all as specified and directed. |
| 31 | M&L for RCC Design mix -25 (using 20mm graded aggregate ) as in lintel beam and roof beam complete all as specified and directed. |
| 32 | M&L for RCC Design mix M-25 (using 20mm graded aggregate ) as in slabs suppotred on walls, beams and columns complete all as specified and directed. |
| 33 | M&L for RCC Design mix M-25 (using 20mm graded aggregate ) as in chajjas and similar work complete all as specified and directed. |
| 34 | M&L for Reinforced Cement concrete (nominal mix) 20mm graded stone aggregate in slab supported on walls, beams and columns, in floors, roofs, landgings, balconies, canopies, deck slab and in shelves and the like complete all as specified and directed. |
| 35 | S & F for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia complete all as specified and directed. |
| 36 | M&L TMT bar 8mm dia cut in shape length incl cranking bending etc and binding with and incl jMS wire not less than 0.9mm complete all as specified and directed. |
| 37 | S&F for TMT bars 5mm dia. and over up to and including 10 mm dia. in stirrups, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed) not less than 0.90 mm dia complete all as specified and directed. |
| 38 | M&L for Roof Treatment in as specified below and as directed :(a) Over the plastered surface apply one coat of composite primer for PU coating as per manufacturers specification. Allow the primer to touch dry condition. (b) Apply 1st coat of PU coating (ShaliUrethane® LHM @ 650 gm/m2 (minimum) or equivelant) by brush / roller / spray, spread waterproofing reinforced Glass Fiber Tissue of 150 GSM with overlaps of 75mm in both directions when the surface is still tacky. Allow 1st coast to dry for 10-12 hrs.(c) Apply 2nd and 3rd coat of PU membrane (ShaliUrethane® LHM @ 650 gm/m2 (minimum) or equivelant) as per manufacturers instructions having sun reflective Index (SRI) of manimum 106 on top of roof surface after application. Treatment is to be extended on vertical and horizontal surfaces of parapet. Note : (i) The minimum thickness of roof treatment shall be 1.5mm. If any shortfall in thickness of above treatment is noticed, the thickness shall be achieved by additional coat.(ii) The plan area shall be considered for payment.(iii) The procurement of material and execution of work of water proofing treatment shall be carried out by authorised applicator approved by GE.(iv) The manufacturer / athorised applicator shall give a warranty for the performance & durability for 10 Years.Make : Fosroc / Sika / Choksey / Bostik / STP |
| 39 | Damp proof course 40mm thick in PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate to horizontal or vertical surfaces including mixed with water proofing compound as per manufacture instructions including necessary form work complete all as specified and directed.Note : Supply only WPC to be measured and paid separately |
| 40 | Supply only integral water proofing compound ISI marked complete all as specified and directed. |
| 41 | M&L brick work with Fly Ash old size bricks straight or curved on plan exceeding 6.0 mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 42 | M&L brick work with Fly Ash old size bricks straight or curved on plan exceeding 6.0 mean radius built in half brick thick walls built in cement mortar 1:6 complete all as specified and directed. |
| 43 | M&L for PCC 1:2:4 type B2(20 mm graded aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed. |
| 44 | M & L brick work with sub class 'B' Bricks, straight or curved on plan to any radius in half brick thick wallsbuilt in cement mortar 1:6 complete all as specified and directed. |
| 45 | M&L 10mm thick rendering in CM 1:6 to brick / concrete wall surfaces finished even & smooth without using extra cement complete all as specified and directed. |
| 46 | M&L 15mm thick, rendering in cement mortar CM 1:6 on faces of brick work or concrete work finished even & smooth w/o using extra cement complete all as specified and directed. |
| 47 | M&L 15mm thick, rendering in cement mortar CM 1:4 to brick/concrete wall surfaces in two layers first layer 10mm thick and second layer 5mm thick with WPC 3% by wt of cement finished even & smooth without using extra cement complete all as specified and directed. |
| 48 | M&L 5 mm thick rendering in CM 1:3 on fair faces of concrete surfaces as on ceilings finished even and smooth without using extra cement complete all as specified and directed. |
| 49 | M&L two coat of Acrylic emulsion on newly pastered wall surfaces over one coat of primer over one coat of wall care putty (1.5mm thick) including preparation of surfaces complete all as specified and directed. |
| 50 | M&L two coat of Acrylic emulsion on newly pastered ceiling surfaces over one coat of wall care putty (1.5mm thick) including preparation of surfaces complete all as specified and directed. |
| 51 | M & L for applying two coat of Premium Acrylic Smooth exterior paint (Apex) over one coat of primer over one coat of wall care putty (1.5mm thick) including preparation of external wall surfaces complete all as specified and directed. |
| 52 | M&L for preparation of newly plastered surface of wall any description and applying two coats of oil emulsion distember over 3 mm thick wall putty over a coat of chalk whiting layer on plastered surfaces preparatory to distempring all as specified and directed. |
| 53 | M&L for three coat of white wash on ceiling on new plastered surface including preparation complete all as specified and directed. |
| 54 | M&L Hardcore of broken stone or boulders, gauge n exc 63 mm, deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface all as specified and directed.(Broken stone or boulders) |
| 55 | M&L 75 mm thick PCC 1:4:8 type D2 using 40mm graded aggregate as in sub base fininshing even and fair complete all as specified and directed. |
| 56 | M&L 25 mm thick cement concrete flooring type B-0, 1:2:4 (12.5 mm graded stone aggregate) finish even and fair complete all as specified and directed. |
| 57 | M&L for non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exc 0.18 sqm laid in floor set and jointed in cement slurry including 15 mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finish even & fair and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed. |
| 58 | M&L for coloured non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm laid in floor set and jointed in cement slurry including 15 mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finish even & fair and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed. |
| 59 | M&L glazed ceramic coloured tiles, (600x300)x7mm thick as on vertical surfaces like dados or skirting over 10mm thick rendering in CM 1:4, set & jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed. |
| 60 | M&L for coloured glazed ceramic tiles in vertical surface 350x250x7 mm / 450x350x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match and including 10mm thick backing coat in CM 1:4 complete all as specified and directed. Please Enable Macros to View BoQ information |
| 61 | M&L for coloured glazed ceramic tiles in vertical surface 350x250x7 mm / 450x350x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match and including 10mm thick backing coat in CM 1:4 complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 06, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Jul 16, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 4 daysJul 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysJul 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender