Tender For Repair To Certain Buildings In Md Accn And Servants Qtrs At Afs Ad Ur
Tender Value
40 Lakhs
Estimated cost
Bid Submission
13 Jul 2026
4 days left
EMD
80000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jalandhar → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Repair To Certain Buildings In Md Accn And Servants Qtrs At Afs Ad Ur
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of Concrete in ground floors and paving n.exc 15 cm thickness (below or above ground level), cement concrete ( un reinforced), etc complete all as specified and directed. |
| 2 | Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed. |
| 3 | Demolition of Concrete of any description and in any position not otherwise specifically provided for, cement concrete ( un reinforced), etc complete all as specified and directed. |
| 4 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, etc complete all as specified and directed. |
| 5 | Demolition of reinforced cement concrete as in chimney, Roofs, floors (other than ground floors), beams staircases, landing, chajjas, and similar suspended work complete all as specified and directed. |
| 6 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.50 Sqm each complete all as specified and directed. |
| 7 | Taking down, Chowkhats or frames exc 1.5 sq. m but n exc 4 sq. m each but with shutters (without taking off shutters from the frame),etc complete all as specified and directed. |
| 8 | Taking down shutter of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each and removing from site complete all as specified and directed. |
| 9 | Taking down shutter for , easing, adjusting of old wooden shutters of any description exc. 1 Sq,m and not exc. 2 Sq.m each and refixing in same opening after tiling work complete all as specified and directed. |
| 10 | Demolition of brickwork built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed. |
| 11 | M&L for RCC 1:2:4 type B-0 (Using 12.5 mm graded stone aggregate)as in chajjas / cooking shelves/platform including necessary form work etc. complete all as specified and as directed. |
| 12 | M & L Brickwork cement mortor 1:6 with flyash bricks, straight or curved on plan exc 6m mean radius built in etc complete all as specified and as directed.. |
| 13 | M & L Brickwork cement mortor 1:4 with flyash bricks, straight or curved on plan to any radius in half brick thick walls built in etc complete all as specified and as directed. |
| 14 | S & F for 300 mm long , Aluminium alloy, anodised ,sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, etc complete all as specified and directed. |
| 15 | S & F 300 mm long mild steel ordinary rat tail rod pattern door spring including roller and roller plate complete all as specified and directed. |
| 16 | S & F in repair floor door stopper of aluminium alloy body double leg 75-80 mm long with rubber stopper at bottom complete all as specified and as directed. |
| 17 | S&F aluminium anodised barrel tower bolt of extruded section 150mm long complete all as specified and as directed. |
| 18 | S & F mild steel chrome finish handles suitable of cabinets/cupboards 100 mm size complete all as specified and as directed. |
| 19 | S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed. |
| 20 | S&F in repair stainless steel conduit 20 mm bore, cut to size and erected in position including provision SS brackets & PVC decorative type finial (Two nos for each opening) Complete all as specified and directed. |
| 21 | S&F 125 mm size, aluminium anodized handles, cast type complete all as specified and directed. |
| 22 | S&F 100mm long butt hinges mild steel medium weight cold rolled Complete all as specified and directed. |
| 23 | S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 24 | S&F in repair Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed. |
| 25 | S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified. |
| 26 | S&F Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) of Fe 410-w Quality-A complete all as specified and as directed. |
| 27 | S&F factory made steel windows with side hung shutter with glazing bars (using profile section as shown in drawing No. CE/AF/STD-170/07, CE/AF/STD-171/07 and CE/AF/STD-172/07 as applicable), each shutter having 02 No. box type hinges & two nos. tower bolts of size not less than 150 mm size and peg stays, dovetailed or welded, complete all as specified and directed. |
| 28 | S&F factory made steel windows with side hung shutter without glazing bars (using profile section as shown in drawing No. CE/AF/STD-170/07, CE/AF/STD-171/07 and CE/AF/STD-172/07 as applicable), each shutter having 02 No. box type hinges & two nos. tower bolts of size not less than 150 mm size and peg stays, dovetailed or welded, complete all as specified and directed. |
| 29 | S & F Steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed. |
| 30 | S & F 30 mm,2nd class hard wood factory made, Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a);,etc complete all as specified and directed. |
| 31 | S & F flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, thickness 30 mm , complete all as specified and directed. |
| 32 | S & F Pressed steel frames made out mild steel sheet 1.25 mm thick, with size of frame 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs,100mm hinges, lock strike plates etc complete all as specified and as directed. |
| 33 | S&F pressed steel frames made out mild steel sheet 1.25 mm thick, with size of frame 105 mm x 60 mm for doors with one or more rebates including necessary fixing lugs,100mm hinges, lock strike plates etc complete all as specified and as directed . |
| 34 | S&F factory made solid PVC Door frame of size 50mm x 47mm made out of 5mm thick wood grain finished colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening, complete all as specified and directed. |
| 35 | S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded wood grain printed PVC Sheet & 5mm thick x 15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mmx10mm (90 Degree)used instead of exposed portion of PVC sheet beading & PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and a gap insert for top rail and bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site all as specified in SSR part-II 2020 Section-8, clause 8B.1 to 8B.2.1 and shown on drawing in page No 146 of SSR part-II 2004. |
| 36 | S&F Sheet glass 4mm thick ordinary quality and glazing with oil putty or wooden beads in squares n. exc. 0.5 Sq.mm in each pane complete all as specified and directed. |
| 37 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, curved chajja, fixed with self tapping screws including dismantling existing rusted/unserviceable sheet all as specified and directed. |
| 38 | M&L for 75 mm thick, cement concrete type C-2, 1:3:6 using40 mm graded stone aggregate, finished even & smooth without using extra cement, as in plinth protection, and joints shall be sealed with joint sealing compound grade 'A' complete all as specified. |
| 39 | Supply & fixing forb 20mm wide & 1mm thick PVC EDGE BENDING of PVC pasted on edges with suitable adhesive , complete all as specified and directed. |
| 40 | Supply & fixing of auto closing hinges openable at 0 degree for kitchen cabinet shutters complete all as specified and directed.Make: Hettich/Ebco/prime |
| 41 | Supply& fixing of ball bearing runners 45mm Telescopic channel (20inch) full extension load capacity 50kgs complete all as specified and directed.Make: Hettich/Ebco/prime |
| 42 | Supply & fixing of stainless steel handles 100mm size for kitchen cabinet shutters, complete all as specified and directed Make: Hettich/Ebco/prime |
| 43 | Supply & fixing of chrome plated stainless steel wire basket (storage basket) pull out type for large utensils, size 486*500mm with necessary fixing clips etc. complete in all respect as specified and as directed.Make: Hettich/Ebco/prime |
| 44 | Supply & fixing of chrome plated stainless steel wire basket (cup and saucer basket) pull out type, size 530*500mm with necessary fixing clips etc. complete in all respect as specified and as directed. Make: Hettich/Ebco/prime |
| 45 | Supply & fixing of chrome plated stainless steel wire basket (jar basket) pull out type, size 536x500mm with necessary fixing clips etc. complete in all respect as specified and as directed. Make: Hettich/Ebco/prime |
| 46 | Supply & fixing of chrome plated stainless steel wire basket (Thali basket) pull out type, size 380*500 mm with necessary fixing clips etc. complete in all respect as specified and as directed.Make: Hettich/Ebco/prime |
| 47 | Supply & fixing of chrome plated stainless steel wire basket pull(cutlery basket) out type, size 380*500 mm with necessary fixing clips etc. complete in all respect as specified and as directed.Make: Hettich/Ebco/prime |
| 48 | Supply & fixing of chrome plated stainless steel wire basket pull (storage/plain basket) out type, size 380*500 mm with necessary s fixing clips etc. complete in all respect as specified and as directed.Make: Hettich/Ebco/prime |
| 49 | Supply & fixing of chrome plated stainless steel wire basket pull (Bottle pull out) out type, size 150 to 200 mm with necessary sliding frame structure, fixing clips etc. complete in all respect as specified and as directed. Make: Hettich/Ebco/prime |
| 50 | S & F 18/19 mm thick High density board (moisture resistance) , flat pressed, single layer type or three layer type with BWR fixed as in wall mounted cabinets, Cupboards etc with necessary screws fittings and fixtures complete all as specified and directed. |
| 51 | M & L for 0.9 mm thick, Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions, complete all as specified and directed. |
| 52 | M & L for 18 mm thick, No of ply 12, plywood, grade BWP, type BB with one side decorative laminate fixed with screws to timber frame work , etc completed all as specified and directed. |
| 53 | Supply only integral water proofing compound complete all as specified and directed. |
| 54 | M & L for 12 mm thick, No of ply 7, plywood, grade BWP, type BB with one side decorative laminate fixed with screws to timber frame work, etc completed all as specified and directed. |
| 55 | M&L for Granite jet black shade, 15-18 mm thick,as in step, jambs, cooking platform and like, machine cut, machine polished, bedded and jointed with grey cement slurry & pointed with grout of matching shade including necessary cutting over & including 10 mm thick (average thickness) cement mortar (1:4), completed all as specified and directed. |
| 56 | M&L for Rounding of / moulding to edges (half round) of stone of any description including rubbing and polishing (Granite finish), completed all as specified and directed. |
| 57 | M&L for 25 mm thick, cement concrete type B-0, 1:2:4 using 12.5 mm graded stone aggregate, finished rough, as in sub floors or similar locations, completed all as specified and directed. |
| 58 | M&L for Glazed ceramic coloured tiles 450x 300x7-8 mm or 600mm x 300mm x 7-8 mm thick on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 10mm thick rendering in cement mortar (1:4) including necessary cutting as per site completed all as specified and directed. |
| 59 | M & L for Dark shade First quality Vitrified Ceramic tiles 9- 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exc 1.00 Sqm , in floors etc. set and jointed in neat cement slurry and pointed in polymer based grout of matcching shed to match over 15mm thick cement screed bed or bedding layer CM 1:4 etc completed all as specified and directed. |
| 60 | M & L for Dark shade First quality Vitrified Ceramic tiles 9- 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exc 1.00 Sqm , in Skirting and vertical surfaces etc. set and jointed in neat cement slurry and pointed in polymer based grout of matcching shed to match including 10 mm rendering in cement mortar (1:4) etc completed all as specified and directed. |
| 61 | Roughening surfaces of old concrete floor by picking ,sweeping clean and washing down with water to remove dust etc including brushing neat cement slurry with 3 kg of cement per sqm completed all as specified and directed. |
| 62 | M & L for Non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm laid in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement with pigment to match the shade of tile laid over and including 15 mm thick bedding layer in cement mortar (1:4) including necessary cutting and waste as per site requirement complete all as specified and directed. |
| 63 | M & L for 100 mm thick, cement concrete type D-2, 1:4:8 using 40 mm graded stone aggregate, finished even & rough, as in sub floors, complete all as specified and directed. |
| 64 | M&L for Providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved design & pattern as in footpath , parks , lawns, drive ways or light traffic parking etc. of required strength , thickness & size/shape, made by table vibratory method using PU mould , laid in required pattern over and including 25 mm thick compacted bed of fine sand , compacting and proper embedding/laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling joints with sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 65 | M&L for Providing and laying at or near ground level factory made kerb stone and drainage channels of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed. |
| 66 | M&L for Repairing of RCC projection chhajjas, roof bottoms, facia etc by necessary preparation. Scraping cutting, chiselling derusting and cleaning exposed reinforcement, surfaces of damaged, loose RCC with cement concrete (1:1.5:3) using 20mm graded stone aggt and reinforcement with welded mesh of weight 2 Kg / Sq.mm but n.exc 3 Kg / Sq.mm (if reqd) with or without facia and finished with cement and sand mortar (1:3) using coarse sand and work in patches area n.exc 5 Sqm and thickness of RCC member n.exc 70mm incl necessary formwork and complete all as specified.(The rate quoted by the contractor shall included for welded mesh, scaffolding and necessary formwork upto triple storey bldg) complete all as specified and directed |
| 67 | M&L for rendering 5 mm thick on fair faces of concrete surfaces, finished fair and even on ceiling surfaces in cement mortar (1:3), complete all as specified and directed. |
| 68 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:6) complete all as specified and directed. |
| 69 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:4) mixed with water proofing compound as per manufacturer instruction complete all as specified and directed.Note:- WPC shall be measured and paid seperately |
| 70 | M&L for preparation of old plastered/unplastered surfaces of concrete ceilings by removing complete existing treatment from ceiling surfaces and applying two coats of oil emulsion distemper (white or tinted) complete all as specified and directed. |
| 71 | M&L for Three coats of white washing on newly plastered ceiling surfaces, including preparation of new surfaces, complete all as specified and directed. |
| 72 | M&L for Preparation of old plastered or un-plastered surface of wall and applying two coats of interior acrylic distemper/oil bound distemper complete all as specified and directed.. |
| 73 | Complete removal of existing treatment of any description, including preparation of wall surfaces of any description complete all as specified and applying the following: -(a) Applying wall care putty, in two coats & smoothening the surfaces with sand papers/ mechanized sanding etc., (preparatory to paint as directed). (b) Two coats of interior acrylic emulsion over and including a coat of acrylic emulsion primer. |
| 74 | M&L for prepration of new plasterd wall surfaces of any description complete all as specified and applying the following: -(a) Applying wall care putty, in two coats & smoothening the surfaces with sand papers/ mechanized sanding etc., (preparatory to paint as directed). (b) Two coats of interior acrylic emulsion over and including a coat of acrylic emulsion primer. |
| 75 | Complete removal of existing treatment of any description, including prepration of wall surfaces of any description complete all as specified and applying the following: -(a) Applying wall care putty, in two coats & smoothening the surfaces with sand papers/ mechanized sanding etc., (preparatory to paint as directed). (b) Two coats of exterior acrylic emulsion over and including a coat of water based exterior primer. |
| 76 | M&L for Prepration of newly plastered wall surfaces of any description and applying the Two coats of exterior acrylic emulsion over and including a coat of acrylic emulsion primer complete all as specified. |
| 77 | M&L for preparation of new wooden surface and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed . |
| 78 | M&L for preparation of old painted wood and wood based surfaces of any description not other wise described over 10cm width or girth and applying one coat (finishing coat) of synthetic enamel paint complete all as specified. |
| 79 | M&L for Preparation of old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat (finishing coat) of synthetic enamel paint complete all as specified and directed . |
| 80 | M&L for Two coats of synthetic enamel paint over & including a coat of red oxide primer over steel & iron (new) surfaces of any description, not otherwise described, over 10 cm in width or girth, including preparation of surfaces complete all as specifieda and directed. |
| 81 | S&F in repair steel tubes ‘medium grade’, galvanized with all fittings and fixed to walls and ceilings or laid in floors , of size: - |
| 82 | 15 mm bore |
| 83 | 20 mmbore |
| 84 | Disconnecting existing tanks of capacity exceeding 250 litre but not exceeding 500 litre, setting aside (or lowering if required) for cleaning/roof repair etc. and hoisting, reconnecting and re-fixing in position after necessary cleaning by removing all scale and dirt etc. including cleaning mouth of circulating service pipes complete, all as specified and directed. |
| 85 | S&F in repair 500 litre capacity, three layered polyethylene water storage tanks (cylindrical vertical with closed top) including hoisted and fixed in position, making connections, , complete all as specified including the following accessories: -(i) PTMT ball valves, high pressure, with epoxy coated aluminium rod & high density plastic ball complete screwed for iron pipe or brass ferrule and fixed, suitable for 20 mm bore GI pipe, complete all as specified.(iii) Gun-metal stop valve (quarter turn type) with MS lever handle, suitable for GI tubes 20 mm bore, ISI marked, screwed both ends for iron pipe, complete all as specified and directed. |
| 86 | S&F in repair 1000 litre capacity three layered polyethylene water storage tanks (cylindrical vertical with closed top) including hoisted and fixed in position, making connections, , complete all as specified including the following accessories: -(i) PTMT ball valves, high pressure, with epoxy coated aluminium rod & high density plastic ball complete screwed for iron pipe or brass ferrule and fixed, suitable for 20 mm bore GI pipe, complete all as specified.(iii) Gun-metal stop valve (quarter turn type) with MS lever handle, suitable for GI tubes 20 mm bore, ISI marked, screwed both ends for iron pipe, complete all as specified and directed. |
| 87 | S&F in repair concealed stop valve/cock, cast copper alloy, chromium plated, with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, complete all as specified and directed. |
| 88 | S&F in repair angular stop valve/cock, cast copper alloy, chromium plated, with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, complete all as specified and directed. |
| 89 | S&F in repair Bib tap, cast copper alloy, chromium plated fancy type, long body with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, I, complete all as specified and directed. |
| 90 | S&F in repair sink mixer with regular spout with hot or cold mounted tap of 15mm bore dia, cast copper alloy, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts fancy type screwed for iron pipe, complete all as specified and directed. |
| 91 | S&F in repair CP Wall mixer for mixing hot & cold water screwed down for iron pipe and fixed , screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe complete all as specified and directed. |
| 92 | S&F in repair CP WHB mixer for mixing hot & cold water screwed down for iron pipe and fixed , screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, complete all as specified and directed. |
| 93 | S&F in repairs Pillar taps, brass chromium plated, fancy type, foam flow, screwed down high pressure screwed for iron pipe 15mm bore, fixed in repairs, all as specified and as directed. |
| 94 | S&F in repair 125 mm size overhead ABS shower with cast copper alloy chromium plated arm 225 mm long with flange and fixed in position, complete all as specified and as directed. |
| 95 | S&F in repair Corner glass shelf, 5mm thick glass, 9\\" wide, fixed with suitable mild steel CP brackets, nuts & bolts, fixed in repairs, all as specified and as directed. |
| 96 | S&F in repair Stainless steel sink with Double Bowl and single drainage board with glossy finish made out of 1.00mm thick sheet for kitchen or laboratory with plug , waste pipe , waste coupling , washers , brackets, connecting union etc overall size 1170mm x510 mm with size of Each Bowl 400mm x 340mm complete all as specified and as directed. |
| 97 | S&F in repair single piece ceramic china EWC (Pedestal pattern) with soft close seat cover , hinges, fixing accessories , accessories set and flushing cistern of size 360 x 640 x 685 complete all as specified and as directed. |
| 98 | S&F in repair Vitreous china EWC (Pedestal pattern) type white complete including plastic WC seat cover white closed pattern with flat bottom and MS chromium plated hinging device complete all as specified and as directed. |
| 99 | S&F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe etc. complete including making good to floor, complete all as specified and directed. |
| 100 | S&F in repairs PVC flushing cistern 10 ltr capacity valve less symphonic action type low level with and incl ball valve float & handle, flush pipe, waste pipe & brackets complete set complete all as specified and directed. |
| 101 | S&F in repair Vitreous China wash basin, white, flat back, size 550 x 400 mm including fixing accessories like galvanised brackets with PTMT waste coupling half or full threaded suitable for & including 32 mm size PVC discharge pipe, complete all as specified and directed. |
| 102 | S&F in repair Stainless steel sink made out of 1.00mm thick sheet for kitchen or laboratory with plug , waste pipe ,washers including cantilever cast iron brackets, connecting union etc overall size 495mm x 420 mm with bowl size 410mm x 330mm x 160 mm complete all as specified |
| 103 | S&F in repair Vitreous China wash basin, white, flat back, size 450x300 mm , waste, chain and plug and porcelain stopper but including brackets |
| 104 | S&F in repair PVC connections 15 mm size of length 450 mm with PTMT nuts, complete all as specified. |
| 105 | S&F in repair 75mm dia uPVC / PVC floor trap with grating including jointing with solvent and embedding in cement concrete type B-1 (1:2:4) IN REPAIR complete all as specified and directed. |
| 106 | S&F in reapair 110mm dia uPVC / PVC floor trap with grating including jointing with solvent and embedding in cement concrete type B-1 (1:2:4) IN REPAIR complete all as specified and directed. |
| 107 | S&F in repair uPVC pipes, type-B, ISI marked (IS:13592) single socketed in any length with rubber ring joints, fixed under floors / fixed to wall as SWR pipes, complete all as specified of size: - |
| 108 | 75 mm external dia pipe |
| 109 | 110 mm external dia pipe |
| 110 | S&F in repair uPVC/PVC bends any radius, complete all as specified. suitable for uPVC soil waste discharge pipes, of size: - |
| 111 | 75 mm external dia pipe |
| 112 | 110 mm external dia pipe |
| 113 | S&F in repair uPVC/PVC Junction single T equal or unequal any radius, complete all as specified. suitable for uPVC soil waste discharge pipes of size: - |
| 114 | 75 mm external dia pipe |
| 115 | 110 mm external dia pipe |
| 116 | Demolition of stone slabs , kota stone/Granite slab of any description or thickness in floor etc complete all as specified and directed. |
| 117 | Dismantling boarding any Description fixed in any position with screws complete all as specified and as directed. |
| 118 | Dismantling of wrought iron of mild steel work of any description in any position not otherwise specifically provided for complete all as specified and directed. |
| 119 | Notes: Amount of credit for retrieved materials is mentioned in tender documents in pdf form which will be deducted while acceptance of tender offline. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 22, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysJul 15, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender