|
| 1 | Taking down chowkats or frame with shutter (without taking out shutter from the frame) not exceeding 1.50 sqm each as doors, windows & ventilators etc. and removal from site all as specified and directed |
| 2 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing and as directed by Engineer-in-Charge |
| 3 | S&F for 30 mm thick factory made solid panel PVC door shutter confirming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 guage thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails MS frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC `C' channel of size 30x50mm forming styles and 5mm thick 75mm wide PVC sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross PVC sheet as gap insert for top rail and bottom rail panelling of 5 mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick PVC sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of 'C' channel using PVC solvent adhesive complete as per manufacturers specifications & drawings ass as directed by Engineer-inCharge. |
| 4 | S&F Aluminium anodised 100 mm long Butt hinges with galvanised mild steel screws complete.all as specified and directed |
| 5 | S&F Aliminium anodised barrel tower bolts, 150 mm long complete.all as specified and directed |
| 6 | S&F Aluminium anodised handles, cast type anodised 125 mm long complete.all as specified and directed |
| 7 | Taking down chowkhats or frame exc 1.5 Sqm but n.exc 4 Sqm each with shutters (W/out taking off shutters from the frames). complete.all as specified and directed |
| 8 | S& F Pressed steel frames of size 125 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, (thickness of sheet shall be 1.25mm) and making good the wall with plaster in CM 1:6 complete.all as specified and directed |
| 9 | S&F for pressed steel frames of size 105 X 60 mm for doors with one or more rebates including necessary fixing lugs hinges, locks strike plate etc, (thickness of sheet shall be 1.25mm) and making good the wall with plaster in CM 1:6 complete all as specified. |
| 10 | S&F for pressed steel frames of size 75 X 60 mm for Cuboard frames with one or more rebates including necessary fixing lugs hinges, locks strike plate etc(thickness of sheet shall be 1.25mm) and making good the wall with plaster in CM 1:6 complete.all as specified and directed |
| 11 | M&L PCC 1:3:6 type C-1 using 20 mm graded stone aggregate for filling in bed block of hold fast etc complete all as specified and as directed. |
| 12 | S&F 2nd class HW 35 mm thick local made panelled shutters with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS-1003 (Pt-I) kiln seasoned and chemically pressure treated complete all as specified and as directed. NOTE :- (i) During fixing of Door Frame, surface shall be make good in plumb with existing finishes like cement plaster, similiar wall tile, floor tile etc and as per site requirement . complete all as specified and as directed. |
| 13 | S&F 35 mm thick glazed skeleton shutters open rebated and prepared to receive guage etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc and fitted to chowkats complete all as specified and as directed.NOTE :- (i) During fixing of Door Frame, surface shall be make good in plumb with existing finishes like cement plaster, similiar wall tile, floor tile etc and as per site requirement . complete all as specified and as directed. |
| 14 | S&F 25 mm thick flush shutter, ISI marked, solid core construction with block board core and plywood face panels commercial face panels, commercial type on both sides.all as specified. |
| 15 | S&F 19 mm thick medium density flat pressed three layer particle board extension grade quality with 5 mm thick teak wood edging on one side bottom and top and other side 10 mm teak wood edging with rebate suitable for cup board shutters complete all as specified and as directed. |
| 16 | Taking down shutters of any description exc. 1 sqm and n. exc. 2 sqm each and removing from site. complete all as specified and as directed. |
| 17 | Taking down shutters of any description n exc. 1 sqm each and removing from site. complete all as specified and as directed. |
| 18 | S& F 18 mm solid PVC ply of 1st quality of both side white colour fixed with screw, solvent cement/adhessive complete all as specified and directed by Engineer-in-charge. |
| 19 | S&F brass Locks, 2 levers for cupboard/Glass doors, grade I, size 50mm complete all as specified and as directed. |
| 20 | S&F Magnetic catcher for Wardrobe, Cub-boards Etc.complete all as specified and as directed. |
| 21 | S&F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and avarage width of aparture 1.40 mm and fixed with tinned tacks or galvanised wire stapple complete all as specified and as directed. |
| 22 | S&F 300 mm size mild steel ordinary rat rail rod pattern springs including roller and roller plate complete. |
| 23 | S&F 250 mm long stainless steel sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of stainless steel (ISI Marked). complete all as specified and as directed. |
| 24 | S&F 200 mm long mild steel barrel tower bolts, ISI market stove enamelled block with bright bolt and fixed complete all as specified and directed. |
| 25 | S&F stainless steel handles, fabricated type of size 150 mm (ISI Marked).complete all as specified and directed. |
| 26 | S&F stainless steel handles, fabricated type of size 100 mm (ISI Marked).complete all as specified and directed. |
| 27 | S&F 100 mm long aluminium anodised hasp and staple safety tape including bolts to hinge plate and fixed with screws complete all as specified and as directed. |
| 28 | S & F Steel window with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded including one shop coat painting complete all as specified and as directed. |
| 29 | All as per Item No 28 here-in-before but without glazing bars. complete all as specified and as directed. |
| 30 | S & F steel ventilators with top hung shutters including hinges steel peg staycomplete all as specified and as directed. |
| 31 | M & L sheet glass ordinary quality 3.00 mm thick and glazing with oil putty in square n exc 0.50 sqm in each panes fixed to steel or wooden window frames complete all as specified and as directed. |
| 32 | All as per item No 31 but pin head type, figured glass complete all as specified and as directed. |
| 33 | Material and labour for preparation of new steel surfaces of any description over 10 cm in width or girth not other wise described and applying two coats of synthetic enamel paint over a one coat of red oxide zinc chrome primer complete all as specified and as directed. |
| 34 | M&L for Preparation of new wood surface of any description over 10cm width or girth applying two coat of synthetic enamel paint over a coat of pink primer complete all as specifed and directed. |
| 35 | S&F stainless steel butt hinges, medium weight of size 100 mm.complete all as specified and as directed. |
| 36 | S&F 125mm stainless steel hasp and staple of safety type with mild steel hinge pin including bolt of hinge plate and fixed with screws.complete all as specified and as directed. |
| 37 | S&F in repair 75mm hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with complete all as specified and directed by Engr-in-charge. |
| 38 | S&F 150 mm long stainless steel barrel tower bolts of extruded section and fixed (ISI Marked).complete all as specified and as directed. |
| 39 | S&F 100 mm long stainless steel barrel tower bolts of extruded section and fixed (ISI Marked).complete all as specified and as directed. |
| 40 | S&F in repair 150mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed by Engr-in-charge. |
| 41 | M&L as in repair for 4.00mm thick acrylic sheet not exceeding 0.50 sqm in each pane & fixed to steel window by drilling holes/punching/ screwing fixed with beads with metal panel pins/spring clips in metal surrounds including taking down old glass with putty, Work to be carried out up to 12m height complete all as specified and directed by Engr-in-charge. |
| 42 | S&F as in repair 6mm thick solid poly carbonate transparent sheet fixed to metel frame using aluminium beading clips screws etc complete as specified and directed by Engr-in-Charge Note : Make of poly carbonate sheet shall be approved by GE |
| 43 | Framed work 410-W (Gde E-250 )as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing including hinges weldingcomplete all as specified and as directed. |
| 44 | S&F in repair welded steel wire fabric n. exc 4Kg per sqm welded to steel section at any position complete all as specified and directed by Engr-in-Charge.Note : Work to be carried out upto 12 to 15 Mtr height |
| 45 | S & F in repairs of venetian blinds, vertical type, 100 mm wide with polyester fabric of approved colour and pattern with aluminium fittings, and top rail and nylon buttons/loops etc fixed cuttings and alteration if necessary where ever AC/ coolers exists complete all as specified. |
| 46 | Easing of steel/wooden window shutter for properly closing/opening tightening of hinges by oiling, greasing or by replacing of new box type hinges including necessary cutting & welding complete. Note:- one unit shall be comprising of one window irrespective of no of leaves/shutter. work to be carried out up to 12m height. |
| 47 | Easing of wooden door shutters/Almn door/PVC door shutter/Almn window (One unit shall comprising of one window/CB/Showcase/irrespective of number of leaves) for properly closing/opening tightening of hinges or changing the position of hinges adjustment of tower bolts sliding bolt etc at any height. |
| 48 | M&L for replacement of wooden glazing beading size or sectional area of exceeding 5 Sq cm but not exceeding 15 Sq cm 2nd class hard wood straight (any size) finished wrought for glazing or gauged joinery for fixing wire gauge/securing glass pane complete all as specified and directed by Engr-in-charge. |
| 49 | Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wind ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe410-0 or Fe 310-0 |
| 50 | S&F in repair 300mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed by Engr-in-charge. |
| 51 | Supply and fixed in repair of 300 mm aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed. |
| 52 | M&L anodised aluminium frame (minimum 50 micron powder coating) for doors, windows, ventilators with one or more rebates including cleat for fixing etc. complete all as specified and directed by Engr-in-charge. |
| 53 | S&F aluminium powder coating of any colour (Thickness of powder coating not less than 50 micron) door shutters, aluminium sections weighing 0.55kg/m incl necessary joining cleat glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, aluminium snap beading screws complete all as specified.NOTE :- (i) During fixing of Door Frame, surface shall be make good in plumb with existing finishes like cement plaster, similiar wall tile, floor tile etc and as per site requirement . complete all as specified and as directed. |
| 54 | S&F aluminium powder coating of any colour (Thickness of powder coating not less than 50 micron) window and ventilator shutter side hung type without sashbar, aluminium sections weighing 0.55kg/m incl necessary joining cleat glazing clips, rubber neoprene packing, alumimium anodised snap beading, screws , peg stay 150mm long -1 No, hinges type B-21 100mm long -2 Nos, suitable handle -1 No complete all as specifiedhandles 2 Nos in each door, hinges, aluminium snap beading screws complete all as specified.NOTE :- (i) During fixing of window surface shall be make good in plumb with existing finishes like cement plaster, similiar wall tile, floor tile etc and as per site requirement . complete all as specified and as directed. |
| 55 | Supply and fixing in repairs 7mm thick aluminium grill of make ' Deco grill DG-104 model fitted in to suitable aluminium channel and fixed to windows / ventilators including channel complete all as directed by Engr-in-charge. |
| 56 | S&F 5.5 mm thick froasted glass panes and glazing exc 0.5 sqm with oil putty or fix in aluminium door / widnow complete all as specified and as directed. |
| 57 | M&L for 12mm th prelaminated particle board, exterior grade, prelaminated both side with decorative choice lamination, fixed with screws to frame work as specified and directed |
| 58 | S&F in repairs double action floor spring hydraulically regulated made up of of minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other parts made of mild steel heavy duty and fixed complete all as specified and as directed. |
| 59 | Repairs to Aluminium doors exc 1.50 Sqm but n exc 5.00 Sqm by necessary joining cleat, glazing clips, rubber neoprene packing handles 2 Nos in each doors, hinges anodised aluminium snap beading screw etc including chowkhat and refix in the same opening after complete repair except glass complete all as specified and as directed. |
| 60 | Repairs to Aluminium doors n exc 1.50 Sqm by necessary joining cleat, glazing clips, rubber neoprene packing handles 2 Nos in each doors, hinges anodised aluminium snap beading scrw etc and refix in the same opening after complete repair except glass complete all as specified and as directed. |
| 61 | S&F in repairs hydraulically regulated door closer aluminum die cast body type complete suitable for door shutter width upto 1000 mm and weight between 61 to 80 kg complete all as specified and directed by Engr-in-charge. |
| 62 | Supply and fixed in repairs of 150 mm aluminium handles cast type anodised.complete all as specified and as directed. |
| 63 | S&F in repair 300 mm, mild steel, ordinary helicalsprings including roller and roller plate complete.complete all as specified and as directed. |
| 64 | S&F Continuous (piano) hinges,mild steel,width of flaps 40mm bright finish or electrogalvanised complete all as specified and as directed. |
| 65 | S&F locally made Steel windows 1.25 mm thick box type (primer coated) ERW hollow P sections of size 60mm X 25mm including grill using 10 SQmm bar double riveted both gaze and glass shutter comprised gauged glazed skelton shutters ERW section 50mm X 20mm and 1mm thick with two openable leafs consisting 2 nos sash bar of T section 20mm X 3mm complete welded to frame with one vertical mullion of ERW box type T section of size 60mm X 25mm and 1.25 mm thick including cutting holes and making good dismanteled portion in PCC 1:2:4 type B1 four numbers of each window including following fittings welded to frame shutter :- (a) Hold fast, 150 mmlong of 12mmX3mm made to shape 04 nos per window (b) handle of Z section 20mmX25mm, 100 mm long -per leaf (c) Mild steel tower bolt 150mm long - 02 Nos per leaf (d) Z section 20mmX25mm, 100 mm long stopper -01 nos per leaf (e) Cleat 55mm long of hollow square 15mm X20mmX63mm welded to hinge -01 Nos per Leaf (f) MS pintal hinges of size 75mmX12mm- 02 Nos per leaf including stainless steel wire cloth, 0.25mm to 0.36mm nominal dia of wire and average width of aperture 1.40mm to 2mm and fixed with aluminium wire staples and glass pan 3mm thick fixed with MS pin and oil putty including two coates of synthetic enamel paint complete all as specified and directed NOTE :- (i) During fixing of window surface shall be make good in plumb with existing finishes like cement plaster, similiar wall tile, floor tile etc and as per site requirement . complete all as specified and as directed. |
| 66 | S&F in repair 5 mm thick sheet glass shelf assembly with Stainless steel backets as approved of size not exc. 0.25 Sqm complete all as speicifed and directed by Engr-in-Charge |
| 67 | M&L for taking out old broken glass of any description from old wooden or metal frame ,or stones, concrete or brick surrounds glazed with putty or fixed with beads including punching or drilling out old glazing pins/spring clips and providing and fixing new sheet glass ordinary quality 3.00 mm thick and glazing with oil putty in square n exc 0.50 sqm in each panes fixed to steel or wooden window frames complete all as specified and as directed. All dismantling/demolished material removed from MOD land completely.Rate of removal outside side from MoD land deemed to be included in the same item. |
| 68 | S&F in repairs stainless steel curtain rod of dia 20-25 mm complete all as specified and as directed. |
| 69 | S&F Stainless steel bracket for holding curtain rodes of dia 20-25 mm complete all as specified and as directed. |
| 70 | S&F of 150 mm floor door stopper of aluminium alloy body and tongue andodised with hard drawn steel spring fixed in floor complete all as specified and as directed. |
| 71 | S&F 40 mm dia cupboard knobs fixed with nut skrew and washer of mild steel bright bolt. complete all as specified and as directed. |
| 72 | Post construction treatment providing and injecting chemical emulsion for post constructional Anti-termite treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per Sqm of the vertical surfaces of the sub-structure to depth of 300 mm including excavating channel along the wall and rodding etc. complete all as specified and directed |
| 73 | Post construction treatment along the external wall on the junction of wall and floor below concrete or masonry apron using emulsion @ 2.25 litre per metre, 300mm apart and 300mm depth including drilling and plugging 12mm dia holes with white cement to match the existing floors complete all as specified and directed by Engr-in-Charge. |
| 74 | Post construction treating of soil under existing floors using emulsion @ one Litre per hole, 300mm apart including drilling and plugging 12mm dia holes with white cement or cement mortar 1:2 to match the existing floors complete all as specified and directed by Engr-in-Charge. |
| 75 | Post construction treatment at points of contact of wood/wall panelling/partision board work by chemical emulsion (in oil or kerosene based solution) @ 0.50ltr /hole by drilling 6mm dia. Hole at a down ward angle of 45 degree at 150mm centre to centre snd sealing the same with matching colour complete all as specified and directed by Engr-In-Charge. |
| 76 | S&F in repairs for aluminium sections used as strip and other members in aluminium rolling shutter and other similar works for existing aluminium door powder coated of any colour (thickness or powder coating not less than 50 micron) as frames for doors, windows, curved rolling shutter strip including interlocking mechanism (1.4 mm thk double layer, width 50-80 mm), ventilators with one or more rebates including jointing cleats for fixing etc. including Taking down existing unserviceable, broken, rusted rolling shutter of any size and type and complete all as specified and directed. complete all as specified and directed. |
| 77 | S&F Steel rolling shutters of 1.25mm thickness of laths, without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated of gear operated type with bevel gear box and crank handle including taking down of old old shutter in any position complete all as specified and directed. |
| 78 | Supply only MS tubing 50mm bore medium grade with necessary holes for shaft complte all as specified and directed. |
| 79 | Supply only MS tubing 40mm bore medium grade with necessary holes for shaft complete all as specified and directed. Please Enable Macros to View BoQ information |
| 80 | Supply only MS tubing 40mm bore medium grade with necessary holes for shaft complete all as specified and directed. Please Enable Macros to View BoQ information |
