|
| 1 | Charges for developing the Borewell with aircompressor of 600 CFM capacity (Minimum8 Hours) including transportation, labour andfuel charges for compressor as directed byTWAD Officers and conducting yield test by‘V’ notch method. |
| 2 | Charges for developing the borewell with aircompressor of 300 CFM capacity (Minimum8 Hours) including transportation labour andfuel charges for compressor as directed byTWAD Board Officers and conducting yieldtest by ‘V’ notch method. |
| 3 | Labour charges for the erection of submersiblepumpset in borewell/openwell including fixingand jointing submersible cable with properclamps upto the starter to required depthand also fixing of riser pipes to the requireddepth valves erection clamps, pressuregauges upto the exterior wall of pump roomand erection of panel board consisting ofTPICN switches starter, Voltmeter, Ammeter,three pilot (indicating) lamps capacitor singlephasing preventor, water level guard andlaying and jointing the cables and twinearthing as per IE rules etc., complete andtesting the pumpset and trail run for 10 days. |
| 4 | Upto 5 HP |
| 5 | Above 5.00 HP to 10.00 H |
| 6 | Above 10.00 HP to 20.00 HP |
| 7 | Conveyance of power pumpset (centrifugal,jet and submersible) and its accessories fromdivisional stores to site of works. |
| 8 | Conveyance upto 10 Kms Pump and its accessorie |
| 9 | Conveyance 10 to 20 Kms |
| 10 | Supply of the following Bold Nut |
| 11 | ½” Bold nut |
| 12 | ¼” Bold nut |
| 13 | 5/8” Bold nut |
| 14 | Removal of Submercible pumpset |
| 15 | Upto 5 HP |
| 16 | Above 5.00 HP to 10.00 HP |
| 17 | Motor Re-erection Charges |
| 18 | Upto 5 HP |
| 19 | Above 5.00 HP to 10.00 HP |
| 20 | Motor Rewinding Charges |
| 21 | Above1HP to 4HP |
| 22 | 4HP to 5HP |
| 23 | 6HP to10HP |
| 24 | Supply of the following submersible Three Phase panel board |
| 25 | Above1HP to 2HP |
| 26 | 3HP to 4HP |
| 27 | 5HP to 6HP |
| 28 | 7.5HP |
| 29 | Supply and delivery of Over Load Relay unit includung cost and conveyance of materials to work site etc complete. |
| 30 | Supply and delivery of Over Load Relay unit Set for 5HP includung cost and conveyance of materials to work site etc complete. |
| 31 | Supply and delivery of Over Load Relay unit Set (oil cup type) up to 10HP includung cost and conveyance of materials to work site etc complete. |
| 32 | Supply and delivery of Over Load Relay unit Set (oil cup type) Above 10HP to 20HP includung cost and conveyance of materials to work site etc complete. |
| 33 | Single Cum Dry running Preventer 6HP to 7.5HP |
| 34 | Volt Meter (0-500V) Range |
| 35 | Ammeter (0-30A) Range |
| 36 | Volt Meter Selector Switch |
| 37 | Teak Wood Board – 2\\"x2\\" size |
| 38 | Magnet (No Volt Coil) |
| 39 | Supply of the following Fuse carrier |
| 40 | Fuse carrier – 16A |
| 41 | Fuse Carrier – 32A |
| 42 | Fuse Carrier – 63A |
| 43 | Fuse Carrier – 100A |
| 44 | Fuse Carrier –200A |
| 45 | Supply of the following 3 core submercible cable |
| 46 | 2.5 Sq. mm 3core submersible cable – 1Mt. p114/ |
| 47 | 4 Sq. mm 3core submersible cable – 1Mt. |
| 48 | 6Sq. mm 3core submersible cable – 1Mt. |
| 49 | 10 Sq. mm 3core submersible cable – 1Mt. |
| 50 | 16 Sq. mm 3core submersible cable – 1Mt. |
| 51 | Supply and delivery of the following 3.3.5.4 core 1 .1kv grade armoured alumium conducted cable includung cost and conveyance of materials to work site etc complete. |
| 52 | 4 sqm |
| 53 | 6 sqm |
| 54 | 10 sqm |
| 55 | 16 sqm |
| 56 | Supply and delivery and fixing of HDPE tank as per IS 12701 / 1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc., |
| 57 | 200 Litres |
| 58 | 500 Litres |
| 59 | 1000 Litres |
| 60 | 2000 Litres |
| 61 | Supply and delivery of the following Spare Parts includung cost and conveyance of materials to work site etc complete. |
| 62 | Motor Bearing Bush |
| 63 | Pump Bearing Bush |
| 64 | Motor Bearing Sleeve |
| 65 | Pump Bearing Sleeve |
| 66 | Distance Bush |
| 67 | Pump Impeller |
| 68 | Impeller Bush |
| 69 | Motor Thrust Bearing Top |
| 70 | Motor Thrust Bearing Bottom |
| 71 | Magnet Coil (No Volt Coil) |
| 72 | Oil Seal Rubber |
| 73 | Oil Seal Push |
| 74 | Supply and delivery of Motor Stud Ring includung cost and conveyance of materials to work site etc complete. |
| 75 | Supply and delivery of Pump Shaft (SS) includung cost and conveyance of materials to work site etc complete. |
| 76 | Supply and delivery of Pump Bowl includung cost and conveyance of materials to work site etc complete. |
| 77 | Supply and delivery of MS Kiosk of size 0.75m x 0.45m x 0.75m made up of MS angle of size 50mm x 50mmx 4mm alround covered with 16 gauge MS sheet and kiosk door made up of MS plates of size 25 mm x 3 mm including cutting, welding, grinding, locking arrangements and labour charges etc., |
| 78 | Supply and delivery of Starter Oil includung cost and conveyance of materials to work site etc complete. |
| 79 | Transporting Charges |
| 80 | Supply and delivery of 7/16 Service Wire Aluminium includung cost and conveyance of materials to work site etc complete. |
| 81 | Service, Commissioning and Testing of DOL Starter including cost and conveyance of materials to work site etc complete |
| 82 | Supplying and delivery of following GI Pipe and Specials as per ISI & ISO Standard Specification. |
| 83 | 50mm GI Medium Pipe |
| 84 | 50mm GI Elbow |
| 85 | 50mm ‘T” |
| 86 | 50mm Coupling |
| 87 | 50mm,ci Flange set |
| 88 | 50mm,GI Bend |
| 89 | 50mm Union |
| 90 | 50mm GM, Gate valve |
| 91 | 50mm C.I. Sluice valve P/66 |
| 92 | 50mm Dummy |
| 93 | 50mm GI Nipple |
| 94 | Sub Total |
| 95 | GST 18% Please Enable Macros to View BoQ information |
