Tender For Detailed Project Report For Proposed Kottapattu Lake Development At Tiruchirappalli City Corporation, Tiruchirappalli-Tamil Nadu

TDR : 56110607

Tender Notice
BOQ

30 Days Left

Tiruchirappalli , Tamil Nadu

Tender Brief : Tender For Detailed Project Report For Proposed Kottapattu Lake Development At Tiruchirappalli City Corporation

Document Fees
Refer document

EMD
₹ 3363000.0 /-

Tender Value
₹ 33.63 Crore /-

Submission Date
23-07-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Dismantling, clearing away the floor finish & dadooing walls in cement mortar with Mosaic Tiles / Glazed Tiles / Clay Tiles / Cuddapah Slabsand carefully stacking materials useful for re-use w-0042 Sor Vol-I pg no:31
2	Clearing Heavy Jungle & conveyence w-0001 Sor Vol-I pg no:29
3	Trimming the bed and the side slope of the bank in all soils except hard rock upto a thickness of 7.5 cm to 15 cm and making it ready to receive the concrete w-0058 Sor Vol-I pg no:363
4	Earth work excavation for desilting the existing rivers / canals / channels/odai/ nullas / drains/flood bowls/tanks/ reservoirs etc., consisting of very loose soil, silt, oily silt, slushy, marshy, loany, organic soil, sea shell and flat mica particles with zero present air void in unhygienic & insanitary conditions in under water and not under water deploying earth moving machinery with suitable floats buoys barge/ hydraulic excavator & other mechanical devices including the cost of hire charges for machinery, with cost of skilled operators with helper & cleaners for the entire operations to reach the banks in which the removed silt & sludge has to be dumped over either one of the rivers / canals / channels/odai/ nullas /drains/floods bowls / tanks / reservoirs etc, bank whichever is convenient as per the prevailing site conditions for easy conveyance and including jungle clearance etc.. complete (Rate excluding conveyance to dumping yard or low lying area) WR-0007 Sor Vol-I pg no:365
5	Boring. providing and installing Bored cast-in-situ reinforced cement Concrete Pile of diameter of 450 mm and length below the pile cap in cement concrete 1:1.5:3 (1 cement, 1 .5 Coarse sand & 3 graded stone aggregate of 20 mm nominal size) to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including Bentonite solution machinery charges labour chargers etc., all complete.
6	Sectioning during forming bunds when earth moving machinery, lorries and rollers are used for consolidation W-0059 Sor vol I pg no:363
7	Turfing in slopes including watering and fixing with initial lead upto 50m W-0073 Sor vol I pg no:364
8	Supply and ﬁlling in foundation and basement with Gravel in layers of not more than 15cm.thick well rammed watered and compacted with surface vibrator, watered and consolidated etc. complete complying with standard speciﬁcation and as directed by the departmental ofﬁcers.
9	Supplying and ﬁlling in foundation, basement, etc with ﬁlling 20 mm HBG Jelly in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard speciﬁcation and as directed by the departmental ofﬁcers.
10	Supplying and ﬁlling in foundation, basement, etc with ﬁlling coarse sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard speciﬁcation and as directed by the departmental ofﬁcers.
11	Supplying and laying of Permeable Paver Block Stone 60mm thick Over a base layer of crushed stone sandﬁlling incl. Cost of materials laying and Labour charges etc complete complying with the standard speciﬁcation and as directed by the departmental ofﬁcers.
12	Supply delivery of natural Pebbles filter media for Filter bed operation & sedimentary bore well of spherical in shape and allow even distribution in support bed with good flow. The media should be double washed, screened, kiln dried and classified into various sizes to meet specification including all incidental charges, conveyance, loading & unloading etc., as directed by the TWAD Board officers.
13	Earth work excavation for foundation by Mechanical means for Isolated & Combined Footing etc in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental ofﬁcers with an initial lead of 100 mts and clearing and levelling including dressing of sides and raming of bottoms etc., complete complying with standard speciﬁcation and as directed by the departmental ofﬁcers.- Upto 2.40m Footing Depth.
14	Earth work excavating and depositing on bank with initial lead of 10m & initial lift of 2m in Sand, silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam and ordinary soil including excavated earth (SS20B)
15	Supplying and ﬁlling in foundation, basement, etc with ﬁlling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard speciﬁcation and as directed by the departmental ofﬁcers.
16	Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc. complete complying with standard speciﬁcation and as directed by the departmental ofﬁcers -Mixing by mechanical means
17	Manufacturing, supplying and ﬁxing in position plain cement concrete precast toe slab of size 600mm x 800mm x 100mm in Cement Concrete 1:2:4 (One cement, Two crushed stone sand and Four jelly) using 20mm HBG stone jelly including cost of moulding charges, casting of slab, ﬁnishing, curing, ﬁxing and pointing the slab with CM 1:3 (One Cement and Three Crushed Stone Sand) to full depth of slab etc., complete complying with standard speciﬁcation and as directed by the departmental ofﬁcers.
18	Manufacturing, supplying and ﬁxing in position plain cement concrete precast toe slab of size 600mm x 600mm x 100mm in Cement Concrete 1:2:4 (One cement, Two crushed stone sand and Four jelly) using 20mm HBG stone jelly including cost of moulding charges, casting of slab, ﬁnishing, curing, ﬁxing and pointing the slab with CM 1:3 (One Cement and Three Crushed Stone Sand) to full depth of slab etc., complete complying with standard speciﬁcation and as directed by the departmental ofﬁcers.
19	Supplying and ﬁlling in foundation, basement, etc with conveyed earth in layers of not more than 150mm thick layers well watered, rammed with surface vibrator and consolidated including conveyance charges etc. complete complying with standard speciﬁcation and as directed by the departmental ofﬁcers.
20	Supply and filling of good quality Garden soil in the ratio of 2:2:1 of good quality existing earth, mixed with Red soil, FYM with all bio organic fertiliserorganic pesticides, fungicides, nutrients and plant growth regulators, etc. HC-W0271 SOR VOL II PG NO:341
21	Providing and laying Woven Geotextiles of Type I on the prepared subgrade as the separator cum reinforcement with necessary overlap as per drawing and as per MORTH Specification 702
22	Manufacturing, supplying and fixing in position GEOCELL(75/712/1.2MM) complete complying with standard specification and as directed by the departmental officers
23	Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, Sill slabs etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner , vertical stiffener, side support and Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals etc. complete in all ﬂoors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid).
24	Supplying and erecting centering for plane surfaces such as RCC Floor/Roof Beam, Lintels, Cantilever Beams, Bed Blocks etc.. with necessary supports and strutting upto 3.60m height in all ﬂoors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over Steel adjustable Span of Size 2m x 2m(expandable upto 3.60m) and Silver Oak Joists of Size 10 x 5 cm spaced at 50cm to 60cm c/c and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) Spaced at not more than 50 to 60cm c/c , etc complete complying with standard speciﬁcations. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Ofﬁcers. (Payment for centering shall be given after the concrete is laid).
25	Supplying and erecting centering for plane surfaces such as RCC Floor Slab, Roof Slab, Loft, Landing Slabs, etc with necessary supports and strutting upto 3.60m height in all ﬂoors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over steel adjustable span of size 2m x 2m (expandable upto 3.60m) and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) , etc complete complying with standard speciﬁcations. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Ofﬁcers. (Payment for centering shall be given after the concrete is laid).
26	Supplying and erecting steel centering including necessary supports For plane surfaces such as rectangular or square RCC columns etc. which require only nominal strutting using mild steel sheets made of 10 gauge thick welded with MS angle size 40mm x 40mm x 5 mm and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick).etc..complete in all ﬂoors complying with standard specifcation. Steel Adjustable telescopic props shall be rovided as directed by the departmental Ofﬁcers. (Payment for centering shall be given after the concrete is laid).
27	Dry Stone Masonry for pitching etc., Complete complying with standard speciﬁcation and as directed by the Departmental Ofﬁcers.
28	Providing and laying in position, standardised concrete Mix M-20 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without inspiring strength and durability with about (5 Cu.m) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 Cu.m) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand, but excluding cost ofreinforcement grill and fabricating charges, centering and shuttering and also including laying,vibrating with mechanical vibrators, ﬁnishing, curing, etc. and providing ﬁxtures like fan clamps in the RCC ﬂoor/ roof slabs wherever necessary without claiming extra, etc.,complete complying with standard speciﬁcation and as directed by the departmental ofﬁcers. The coarse and ﬁne aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).
29	Basement
30	Ground Floor
31	Vibrated Reinforced Cement Concrete M20 (Design mix) using 20 mm ISS HBG graded metal including cost and conveyance of all materials to site and cement at site excluding cost and fabrication of steel but form work and centering soft water labour charges for mixing, transporting, placing in position, vibrating and compacting finishing and curing concrete, working at heights, hire charges for Hire charges for Tools and plants, including all other incidental charges, etc., complete as per standard specifications for MAT CONCRETE
32	Vibrated Reinforced Cement Concrete M20 (Design mix) using 20 mm ISS HBG graded metal including cost and conveyance of all materials to site and cement at site excluding cost and fabrication of steel but form work and centering soft water labour charges for mixing, transporting, placing in position, vibrating and compacting finishing and curing concrete, working at heights, hire charges for Hire charges for Tools and plants, including all other incidental charges, etc., complete as per standard specifications for SIDE WALL
33	Vibrated Reinforced Cement Concrete M20 (Design mix) using 20 mm ISS HBG graded metal including cost and conveyance of all materials to site and cement at site excluding cost and fabrication of steel but form work and centering soft water labour charges for mixing, transporting, placing in position, vibrating and compacting finishing and curing concrete, working at heights, hire charges for Hire charges for Tools and plants, including all other incidental charges, etc., complete as per standard specifications for DECK SLAB
34	Manufacturing, supplying and ﬁxing Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two crushed stone sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, ﬁnishing, curing and ﬁxing in position in all ﬂoors etc., complete complying with standard speciﬁcation and as directed by the departmental ofﬁcers.
35	Providing and laying in position, Standardised Concrete Mix M-25 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350 kglm3 and maximum water cement ratio of 0.50, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 Cu.m) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 Cu.m) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m’) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, ﬁnishing, curing, etc. and providing ﬁxtures like fan clamps in the RCC ﬂoor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard speciﬁcation and as directed by the departmental ofﬁcers. The coarse and ﬁne aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).
36	Foundation
37	For Ground floor
38	Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel reinforcement grills of all variety like HYSD/CTD/TMTand all grade like Fe 500, Fe550D, Fe 500 D etc., for all RCC works as per design given including cost of steel reinforcement and G.I. binding wire, wastage etc. complete complying with standard speciﬁcation and as directed by the departmental ofﬁcers.(Contractor has to make his own arrangements for the supply of steel reinforcement and binding wire)
39	Add additional labour for works above plinth/Basement level in every upper ﬂoor over the preceding ﬂoor or Below Ground level of every 3.50m depth.
40	Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification
41	Brick work in following Cement Mortar using best quality Burnt Clay Brick of size 8 3/4” x 4 1/4” x 2 3/4” with class designation of 7.5 conforming to IS 1077-1992 for foundation and basement including Cost of Mortar Plasticizer curing, etc.,complete complying with standard speciﬁcation and as directed by the departmental ofﬁcers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done as directed by the Executive Engineer in charge.
42	Basement Floor
43	Ground Floor
44	Brick partition walls of 11.50cm thickness using best quality Burnt Clay Brick of size 9” x 4 1/2” x 3” with class designation of 7.5 conforming to IS 1077-1992 in Cement Mortar 1:3 (One Cement and Three CS Sand) using hoop iron reinforcement if found necessary including Cost of Mortar Plasticizer, curing etc. complete complying with standard speciﬁcation and as directed by the departmental ofﬁcers. (Hoop iron reinforcement will be measured and paid for separately)
45	Ground Floor
46	Paving the ﬂoor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in accordance with IS 1443 over a cement mortar bed of 20mm thick in Cement Mortar 1:3 (One Cement and Three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard speciﬁcation and as directed by the departmental ofﬁcers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)
47	Supplying and ﬁxing Medium Density Fibre board (SBG I) of exterior grade of following type with thickness conforming to IS 12406 / 2003 with necessary adhesive and C.P. screws, including ﬁxing of aldrops, tower bolts, hinges and lock strike plates, putty, fevical, varnish for T.W. lipping with thinner colouring agent etc.,The rate includes cost of materials and cost for furniture ﬁttings such as 3 nos SS 304 Grade Parliament inges of required Size (125mm x 150mm), 1 no Alu. aldrop 250 x 16mm, 2no Alu. tower bolt of 300x12mm and 1 no Alu. tower bolt of 200x12mm, 2 Nos Alu. Handles, 1 no door stopper with rubber bush incase of Single leaf door, cost of labour charges for ﬁxing in position etc., complete. All Aluminium furniture ﬁttings are to be anodised with matt ﬁnish under electrically controlled condition in accordance with ISI speciﬁcation 1868/1968 for anodic ﬁlm thickness of not less than 15 microns, The rate is inclusive cost of fevical and ﬁxing charges, transportation, loading, unloading and all other incidential charges, handling charges etc., complete complying with standard speciﬁcation and as directed by the departmental ofﬁcers -Single leaf.
48	UPVC WindowSpecification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work(PWD SOR Pg. No. 65)
49	Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete (PWD SOR P.NO :57)
50	Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (One Cement add three sand) 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete
51	Weathering Course with Concrete Broken Brick (S.I.No.278) & ( P & D) Data 54.Jelly 20mm gauge in pure slaked lime (no sand to be added) over roof slab,the proportion of brick jelly to lime being '32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers etc., complete.-10 cum
52	Supplying and fixing of teak wood flush shutters 32 mm thick made out of TW frames and TW ply with 4 nos. bolt hinges 12.50 cm in size one aldrop, two tower bolts handle locking arrangement complete including cost of materials furniture and labour etc., complete
53	UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames.The ventilator should be got approved from the Executive Engineer before use on work
54	Providing and fixing structural glazing fabricated from roll formed sections made of galvanized steel colour coated (Base steel as per IS 513 of ‘D’ quality, galvanized as per IS 277 with Zinc of 120 grams / sqm.) with total coated thickness of 0.72mm. The glass holding section made of 304 grade SS of 0.6mm thick. Galvanized steel sections are to be used as stiffeners inside the colour coated steel / powder coated sections as per the design requirement. Design calculations are made to suit wind pressures as given in IS 875.Paint specifications: Primer coat with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick.Dimensions: The section should be of 37 x 53mm for frame vertical, 37 x 53mm for frame horizontal section and section for reinforcement should be of 31 x 55mm. glass holding section should be of 37 x 37mm for top and bottom grids in between should be of 37 x 18mm.Accessories: Brackets made of CRCA powder coated / electro plated should be used to fix vertical at top and bottom and vertical to slab as per site requirement. Polyurethane brackets should be used to connect horizontal section to vertical sections.Silicone: Natural cure, with good UV resistance to be used. The above frame should be fixed to brick / concrete masonry by using nylon self–expanding cap and driving MS electro plated 80mm long screws into the caps through frames.Glass: 5mm reflective Saint Gobain OR equivalent.
55	Supplying and Fixing of Stainless Steel Dye Cast Letters of approved size and colour. The colour treatment process is achieved with MRF colour coat and then the processed coloured layer is set into the kiln for the heat treatment process for the following sizes
56	Paving the ﬂoor with best approved quality ﬁne polished flamed ruby Granite Stone Slabs of following size and Variety with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., complete complying with standard speiciﬁcation and as directed by the departmental ofﬁcers.(The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work)
57	Paving the ﬂoor with best approved quality ﬁne polished Granite Jet black Stone Slabs of following size and Variety with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., complete complying with standard speiciﬁcation and as directed by the departmental ofﬁcers.(The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work)
58	Supplying and laying of Interlocking Paver Block Stone 63mm thick Over a base layer of crushed stone sandﬁlling incl. Cost of materials laying and Labour charges etc complete complying with the standard speciﬁcation and as directed by the departmental ofﬁcers.
59	Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all ﬂoors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard speciﬁcation and as directed by the departmental ofﬁcers
60	Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers
61	Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.
62	Painting two coats with ready mixed plastic emulstion paint of first class quality paint and approved colour including priming coat through scrapping clean removal of dust etc., complete
63	Supply and fixing in position of cut stone cover slabs roughly dressed in all sides including fixing in position with cement mortar 1:3 mix and pointing with the same mortar etc., complete 1 m3
64	Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.
65	Supplying and laying wooden flooring at site 8mm thick of approved make using click laminated floor with inbuilt 3mm sound bloc class of use 31 water resistant AC 3 grade impact resistant IC3 (as per EN 130 900 / 1400) having 0.60mm MLC (Multi-Layer Guard + SRSG 2) (Scratch Resistant Surface Second Generation) on top of misture high density fibre board substrate specially developed copr of plank size 1288 x 196 x 8mm having joints tongue and groove to secure long lasting joint. The tongue and groove havng the edges duly pre impregnated with par affine including laying 0.20mm thick alkali resistant polyethylene sheet of density 850 kg / m3 beneath the laminated wooden panel to absorb the sound caused including labour charges, loading, unloading, transportation, etc., complete
66	Supplying and Fixing GI pipe 32 mm dia (B class) including cutting and fixing in to kerb wall for30 cm depth including fixing weld mesh 7.5 cm x 5cm 10 gauge and fixing welding with MS angle 35 x 35 x 6mm allround and with MS Flat 45 x 6mm at middle including Conveyance etc ., Complete
67	Providing and fixing wooden seating made of high-quality seasoned hardwood / approved quality wood, free from defects such as cracks, warping, or insect attack. The seating shall be designed as per approved drawings and specifications, including required dimensions, profiles, and ergonomics.The wooden members shall be properly cut, shaped, and finished, with all joints neatly executed using approved carpentry methods. All surfaces shall be smoothly planed, sanded, and finished with approved wood polish / melamine / PU finish / varnish as specified, including necessary primer and sealant coats.The seating shall be securely fixed in position using approved hardware such as stainless steel / brass screws, bolts, and concealed fittings, ensuring stability and durability. Exposed edges shall be rounded and finished neatly for safety and comfort.The work includes all materials, labor, tools, fittings, finishing, and fixing complete, as per site conditions, drawings, and the direction of the Engineer-in-Charge / Architect.
68	Supply & stacking of red earth at site to the departmental guage for pre-measurements which is of light textured, crystalline, porous and friable and not of generally acidic or neutral but not of alkaline and should be fertile, including seignior age charges, cost of transportation, loading, unloading, stacking and inclusive of all taxes etc., complete.
69	Supply of Vermicompost in powder form, devoid of impurities and other materials, nutrient dense and which supports plant growth including cost of transportation
70	Truffing of Korean grass / mexican grass including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge.
71	Planting of Ficus black ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges,transportation, stacking of saplings at site, earthwork excavation of required size, planting ofsapling, refilling of excavated earth etc as directed by the site in-charge. HC-W0068 VOL-II SOR 24-25 PG.NO :276
72	Planting of Nerium oleander dwarf foliage shrub variety of height 30-45 cm in polythene bag of size6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.HC-W0094 VOL-II SOR 24-25 PG.NO :280
73	Planting of Jasmine Plant foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges,transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge. HC-W0081 VOL-II SOR 24-25 PG.NO :278
74	Planting of Ixora ordinary foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inchincluding loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting ofsapling, refilling of excavated earth etc as directed by the site in-charge.HC-W0080 VOL-II SOR 24-25 PG.NO :278
75	Planting of Murraya exotica foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the sitein-charge. HC-W0092 VOL-II SOR 24-25 PG.NO :280
76	Supplying and Planting of Ashoka tree sapling of height 240 –300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.\\"
77	Supplying and Planting of Neem tree sapling of height 240–300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.\\"
78	Supply and planting of Ficus bengalenisis tree sapling of height 150-180 Cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, Supply and planting of sapling, refilling of excavated earth etc as directed by the site in- charge.
79	\\"Supplying and Planting of Poovarasu tree sapling of height 240–300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.\\"
80	Supplying and Planting of Pungam tree sapling of height 240 –300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.\\"
81	Supply and planting of Bougainvillea hybrid foilage shrub variety of height 30-45 cm in polythene bag of size 6x7 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, Supply and planting of sapling, refilling of excavated earth etc as directed by the site in- charge.
82	Supply and planting of Witchie meril gold palm variety of height 180-210 cm in polythene bag of size 21x21 inch including supporting stack of 5 cm dia casuarina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in- charge.
83	providing and fixing stainless steel handrail of SS 304 / SS 316 grade, of approved diameter and thickness, including posts, fittings, welding, grinding, polishing (mirror / satin / hairline finish), anchor fasteners, and fixing complete as per approved drawings and directions of the Engineer-in-Charge.
84	\\"Design, fabrication and installation of simple vault tensile fabric work and Steel structure using Belgian make tensile polyester fabric, steel frames by ISO standard acclaimed CE certified installer with structural stability vetting from Anna university ,Chennai having using FLUOMAX Coated Architectural Membrane having tensile strength not less than 4300 N/50mm/ 4200 N/50mm (Warp/ Weft) and Tear strength not less than 600 N/ 500 N (Warp/ Weft) of make SIOEN Belgium or equivalent, cables, complete perimeter attachment system, and all normally associated components with machines for Fabrication using swiss make Zund cutting machine and Belgian HC-W0301 PD-1889 make
85	Architectural Membrane on 20KW Forsstrom High Frequency Welding Machine with SEAMLESS WELDS 50 mm weld width X 1400 mm- Single Stroke all PVC joints shall be formed to a tolerance of +1mm, -1mm and shall be assembled to ensure that seams are always single laid and attaining seamless finish by that a cut edge does not face uphill and membrane used to have a double lacquering made out of highly concentrated FLUOMAX PVDF on both side, double PVC coating and be weldable without grinding to make sure the fabric have less environmental impact the fabricator has to deliver evidence of REAC conformit a per the European Norms the fabric to have Color light fastness not less than >6 Note in accordance with the German standard DIN 54004, DIN EN ISO 105 B02 and have 15 years manufacturer warranty All Fabric supplied and installed shall be in accordance with this specification and shall be guaranteed against water leakage, faulty materials and Mild steel structure supplied are made of high quality pure steel HR coil and the tubes to conform\\"
86	Providing and fixing GRC (Glassfibre Reinforced Cement Conrete) Architectural Elements in approrved size, pattern, design shade and thickness of 25mm. The GRC product Shall be made from ‘53grade’ White Portland Cement manufactured by ‘JKCement’ or equivalent, Finegraded Quartz & SilicaSand, Alkali Resistant Glass Fiber manufactured by N.E.G JAPAN’ or equivalent, Super Plasticizers manufactured by ‘ZPXRC’ or equivalent, Polymers manufactured by ‘DowChemicals’ or equivalent and U.V resistant Synthetic inorganic pigments should be used for pigmentation manufactured by Lanxess / ‘BAYFERROX (Germany)’ or equivalent. The material casting should take place in FRP Moulds.
87	The GRC material flexural strength average L.O.P shall be above or equivalent to 6N/mm2 & M.O.P should be above or equivalent to 15N/mm2 for tests done on 28 days cured samples.The dry density, water absorption, Compressive strength and tensile strength of GRC material shall be 1800 to 2000kg/Cum, less than 8% of dry weight by immersion over a period of 24hours, M - 40 Grade concrete mix design with compressive strength of 400kg/cm² (in 28days cube testing) and 4 - 7 MPa respectively The rate shall includes labour charges for fixing the GRC Elements to MS frame work by using M.S Galvanized Clamps, fixtures and fasteners of Hilti / Fischer or self-tapping screws or as per approved shop drawings approved by site engineer in charge. etc., cleaning and making the surface good for painting, complete all as directed by Engineer In-Charge (Cost of MS frame work to which the Architectural elements fixed shall be paid separately elsewhere as an item)
88	FOUNTAIN MECHANICAL DETAILS Labour charges for the erection of submersible pumpset in openwell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, Voltmeter, Ammeter, three pilot (indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc.,complete and testing the pumpset and trail run for 10 days. vol -1 Upto 5 HP PWD SOR P.NO :156
89	\\"Supply, Fixing & commissioning of Pop up spray head RD 1804 SAM PRS Series Spray bodies, with Rotary nozzle with capable of covering 4.0-7.3m at 1.4 - 3.8 Bars pressure, Rotary nozzles shall have hand adjustable ( without tools) radius and arc-45 to270 degree or full circle True flushing mechanism, Thick streams and large water droplet & Low precipitation rate Triple Blade Wiper Seal precisely balances flushing, flow-by and debris protection to optimize performance and durability at pop- up and retraction. Precision-controlled flushing at pop-up and retraction clears debris, ensuring positive stem retraction in all soil types. Unique debris pockets hold grit in place, removing it from circulation and preventing long-term damage. Parts resistant to corrosion in treated recycled water containing chlorine. Pop spray body shall with stand upto 6.9 bar. Built-in Seal-A-Matic™ (SAM) check valve. Traps water in lateral pipes in elevation changes of up to 14 feet (4.2 m). PRS Maintains constant outlet pressure at 30 psi or 45 psi at varying inlet pressures, Flow-Shield™ technology and molded purple / White covers. etc. including installation charges\\" VOL-II PWD SOR P.NO :319 PD-1908
90	Supplying and fixing of water level independent Vertical jets of 0.5 inches BSP connection vertical jet at size of 100 mm height with 23 mm orifice with ball joints made up of brass with nickel plating etc, complete 1.0 HP Jet Pump Set VOL-1 PWD SOR P.NO :156 M-1059
91	Brass Isolation Valve suitable for the copper pipe and should be of non lubricated 90 degree turn lever ball valve of reputed make, conneced in line with medical gas pipe line system by using suitable size brass valve adopter union, ferrule, nipple, rubber “O’ ring, tapion lap and etc. All pipe line regulators shall be capable of controlling pipe line pressure and must compatible with the requirements specified in IS 12827-1989. All valves should be pneumatically tested for twice the working pressure for the gas line as per IS Code 12827 / 1989 & ISO 7396 / 1987 Sepecification. 22mm Isolation Valve PWD SOR P.NO :120 M-0737
92	Supplying and fixing of Multi-colour 80W LED Focus Light Fitting with LED– 12 Volts RGB L.E.D lights made up of die cast stainless steel 304 grade suitable to be fitted with emitter type power LED’s with all in one optical lens of 85% efficiency step tempered glass 8 mm with protection class of Ip-68 I/C connection & water proof jointing sealed with heat resistant with mounting cradle etc. complete. VOL-1 PWD SOR P.NO : 169
93	Supplying and fixing of Supreme or equivalent make UPVC Pipe (Un-Plasticized Polyvinyl Chloride) UPVC used handle higher water pressure (Schedule-80)UPVC fittings & control valves for connect pump to 12 feet dia ring etc. complete.
94	Supplying and fixing of 3’ x 2.5’ size of wire mesh of size 1 cm x 1cm 2mm thick 14 gauge unit made up of stainless steel with SS frame for protect the pump from the dust and garbage articles etc. complete
95	Supply and fixing of 6W LED Outdoor Bollard light (Philips/Havells) complete with T.W round blocks of 6\\" dia and height 0.9m.
96	Supply and delivery of SWING TYPE SS MADE 200 LIT CAPACITY 4 COMPARTMENT STEEL DUSTBIN (FOODS , PLASTICS, PAPERS & GENERAL) shall conform to following specifications:-G• The material shall be heat and chemical resistant and shall be UV stabilized.The manufacturing process shall be Injection molding only as specified by EN 840-1 standard.The bins shall have suitable lid of HDPE Injection Molded at the top which shall be hinged on one side and open easily by gravity while unloading in refuse compactors.The bins shall have Nominal volume of 240 Ltrs.The bins shall have Two Solid rubber wheels of 200 mm Dia. (+-5 mm). Both these wheels shall be mounted on axle, which shall be corrosion resistant.The bins shall be provided with single piece pulling handle.The bins shall have deep and strong combs as per EN Standards. These combs shall ensure optimum accommodation on the lifting devices i.e. Refuse Compactors with Universal Bin Lifting mechanism.The useful load shall be min. 110 Kgs. As per EN standard.The color of the bins shall be Green/Blue/Grey/Yellow/Red and aesthetically pleasant in nature.(Q)
97	Supply, delivery and erecting of 1.50m long PARK BENCH in aged people rest shed made with Stainless steel pipe of size 2\\" x 1\\" supported with necessary SS legs including all cost of materials and labour charges for fixing in position with necessary Plain Cement Concrete work and digging work to a size of 0.50m x 0.50m x 0.50m and erecting the Stainless Steel unit etc. complete.
98	PLAY EQUIPMENTS Supply and fixing of ARCH SEA SAW Sea saw made of G.I.sheets with 2 Stainless Steel Pipes Boards to play 4 Children simultaneously. Seats made of fiber reinforced plastic SI:NO: 40 CPE-144
99	Supply and fixing of Merry go round – 6 Seater (FRP) Height :3” GI Pipe, 2.5mm thick, b class Seat size:15” X 14”, paint: pu coating SI:NO: 25 CPE-129
100	Supply and fixing of Swing 2 seater Height of 7ft 0” above the ground level and width of 10ft 0”. Legs made of 40mm Stainless Steel pipes and 31 Cross Bars made of 50mm SS pipes Seats fiber CPE-135 Each 64253.00 reinforced plastic seats suspended with 6mm thick in coated chain etc SI:NO: 31 CPE-135
101	Supply and fixing of Roller Slide 8ft: Measurement] Height:5ft Width: 2ft Sliding Chute:10ft Roller thickness:3mm PVC Roller with½ inch galvanished pipes. No. of Rollers.46 with multicolours. Painting with PU coating [Required area] Product area: 21/2’ft * 14’ft Play area:6’ft * 18’ft SI:NO: 06 CPE-110
102	Supply and fixing of Jungle Gym:[Component] Galvanished ‘B’ Class pipe painting with PU coating [Required area] Product area :5’ft * 5’ft Play area: 7’ft* 7’ft CPE - 116
103	Supply and fixing of Hip Twister – Double persons sitting standing any combination Height :21/2”Pipe,11/4”pipe,3/4”pipe, 2.5mm thick, B class, height:41/2’ product size:5’*1’ Paint:pu coating CPE - 130
104	Supply and fixing of Double Bar / Parallel Bar Frame:1/2”GI pipe, 2.5mm thick, B class, height:41/2’, product size:6’*2’ paint: pu coating CPE - 131
105	Providing Granolythic finish of 25mm thich with PCC 1:2:4 (One cement, two sand and four jelly) using 10mm to 12.50mm HBG jelly etc complete
106	Providing and applying primer and two coats of 100% Acrylic breathable, Anti-Carbonation, waterproof, heat insulating, decorative exterior coating of approved shade after applying a primer coat of same material and apply two coats of mix 1 ltr with 400 - 500 ml water, it shall be applied as per manufacture specification. Acrylic paint shall be spray / brush / roller applied and shall conform to the following properties. Carbon dioxide diffusion equivalent air layer thickness (DIN EN 1062-6) > 100m; Carbon dioxide diffusion resistance coefficient (DIN EN 1062-6) > 105; Elongation of cured film shall be as per ASTMD 2370/98 > 400%; Chloride iron diffusion (ASTM C 1202) = Zero penetration; Adhesion to concrete (ASTM D 4541) > 2 N/mm2; Solar Reflective Index (ASTM E 1980 - 11, EN 673; 2011, EN 410: 2011) > 104. The inter-coat gap to be 24 hours. The rate shall include complete treatment mentioned above and should not be less than DFT 200-225 microns for primer and two coats as per relevant MoRT&H specification Resurfacer layer 1&2 HW-W0067 VOL -1 PWD SOR P.NO : 278
107	Providing and applying Painting the wall with Texture Finish Paint including labour charges the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers. M-0427 PWD SOR P.NO : 83
108	Providing and applying Painting Epoxy primer paint including labour charges the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.
109	STREET LIGHT POLESupply and fixing of 65 mm dia. (2 -1/2\\") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED street light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED street light fitting and SMC box with PVC unsheathed FRLS copper leads from SMC box to fitting and with painting of suitable colour
110	Supplying and erectingof 16 Mtrs. High Mast WITH 8 NOS 150N LED fitting Polygonal Shapes. Suitable for 12 luminaries for Wind Speed up to 180 Km/hr. As per IS -875 Parts -3 Material Cons.: BSEN 10025 # Mechanical Components including Head Frame & Pulley Assay, Winch Bracket, Lantern Carriage Ring, Luminaries and C.G Box Mtg. Arms, Resting Bracket Guide Ring, Compensating Disc, Lightening Arrestor.etc. ( Each Set ) # Wire Rope, Safety Wire Rope, D Suckle Clamps, Nuts and Bolts. # Cable with termination & distribution box. # Foundation Accessories. # Winch Assembly # Power tool. Mast bottom Dia:415 mm. Top : 150 mm, Thk: 4,3,3 mm. Motor-1.Feeder pillar box comprising 100 ams fuse unit 24 hours timer 1-nos and contactor 1-nos outgoing MCB toggle switch and neutral link with internal wiring made of MS sheet and vermin proof.Erection and commissioning of 20 Mtr high mast on the above said concrete foundation using suitable equipments. Fixing of flood light luminaries in the lantern carriage including internal wiring & using flexible copper cable complete. Halonix LED Flood light 300/W ( CW ) 12 nos (16 Metre) with 8 Nos. 150W LED FittinG (pwd sor pg no :150)
111	Manufacturing, Supplying and Fixing of solid Waste Bins of Size 1m x 0.30m with necessary Supporting with arrangements Including cost and conveyance of all materials to Siteand labour charges etc,.complete as per standard specifications For Park
112	Supply, delivery and erecting of 2.50m long PARK BENCH in aged people rest shed made with Wooden of size 2\\" x 1\\" supported with necessary SS legs including all cost of materials and labour charges for fixing in position with necessary Plain Cement Concrete work and digging work to a size of 0.50m x 0.50m x 0.50m and erecting the Stainless Steel unit etc. complete.
113	Supply and delivery of MS Kiosk of size 0.75m x 0.45m x 0.75m made up of MS angle of size 50mm x 50mmx 4mm alround covered with 16 gauge MS sheet and kiosk door made up of MS plates of size 25 mm x 3 mm including cutting, welding, grinding, locking arrangements and labour charges etc.,
114	Supply fixing and errection of CCTV Camara including cost and Conveyance of all materials to site etc complete as per Specification (5units / park)
115	CCTV Camera
116	Network Video Recorder
117	Hard disc for NVR 4TB
118	24 Port Patch Panel
119	Rack With Accesssories -3U
120	Armoured LAN & CCTV Cable
121	Led tv for display
122	Providing and erecting of Direction and Place Identification Retro-reflectorised Sign made out of High Intensity Prismatic Grade Sheeting confirming to Type-IV standards of IRC-67: 2012 and ASTM D 4956 —09, specification and fixed over 2mm thickAluminium sheet fixed over a back supporting frame of 25mmx25mmx3mm Mild Steel angle and supported on a mild steel angle post 75X75X6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sign board and 0.6Om below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cmX45cmX60cm size including cost and conveyance of all materials, equipment, Machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge. High intensity Retro Reflectro sheet shall consist of minimum coefficient of Retro-reflection as per Table 6.6 of IRC 67-2012. The retro- reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67:2012. (as per MORT&H Specification No.801)
123	Supplying and erecting in position of following liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No.(e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., LevelSwitch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact. (250 Litres) pwd sor pg no 72)
124	Supply and fixing of sprinkler system made of steel pipe and maximum working pressure 360 deg rotating wirh four arm rotating disc of 175 using some models are available corrosion resistance black pipe and copper pipe and also used plastic pipe cpvc and pex Three standard astm A53, astm A135, astm A 795 .SPARAYER HEAD 8 TO 16 Diameter space 12-15 feet location are grid. Head requires 200 square feet. all complete complying with standard specification as directed by the departmental officer....
125	Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer
126	Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete PWD SOR Pg. No. 63 Sl.No. 239
127	Supply and fixing of CI Sluice gate of Single Face (Class-I)- 600 x 600mm
128	Supply and Fixing of HDPE Modular Boat Jetty with Floating cubes including lock pins & nut Bolt and all necessary Fittings, including all cost of materials and labour charges for fixing in position etc, complete
129	Providing, installing, and commissioning floating wetland system comprising modular floating platforms made of HDPE / approved material, planted with suitable native aquatic vegetation, including buoyancy elements, planting media, anchoring system, and all accessories, complete as per approved design, drawings, and directions of the Engineer-in-Charge
130	LAKE AERATOR Lake Aerator Shall be mechanical aerators of clog free design suitable for floatable conditions with 1.AERATOR BODY with 6 Nos of Engineer Polypropylene plates Simona make (2 Nos long size plates of Length 2500mm and Height 1200mm) and 2 Nos short side plates of Length 1500mm and Height 1200mm and 1 No Top side plate of Length 2500mm and Breadth 1500mm and 1 No. bottom plate of Length 2500mm and Breadth 1500mm. The welding shall be extrusion welding. The dimension ratio of the aerator body is 2.5L X 1.5B X 1.2H. The number of exits port shall be 20 of Dia 141mm and the number of suction port shall be 20 nos. of Dia 141mm.2.SPLASH PROOF ENCLOSURE. The blower enclosure have five sides constructed of Engineer Polypropylene plastic plate with bottom open. The open bottom is placed over the blower and fixed to the top plate of the aerator box by fastening bolts. The side plate of the blower enclosure is provided with a plurality of circular openings for air ventilation during operation.
131	Each of these circular openings should be provided with “L” type fittings on the inner side of plates to prevent water entry during rain periods. 3.AERATOR INTERNALS with air distribution assembly with loop header fitted with distribution nozzles and draft tubes. 20 Nos of Air injection assembly with injector, connector, Gas tube, Slotted tube and Suction tubes. Ballast tank of suitable diameter based on the actual weight of system shall be provided. 4.SCREEN MESH: Screen mesh constructed of perforated Engineered Polypropylene plates Simona make or equivalent suitable to cover all the suction tubes. 5.BLOWER/ELECTRIC MOTOR High speed centrifugal blower with flow rate 1200 m3 /hr, maximum pressure difference is 100 mbar with an aero dynamic impeller and casing. The motor shall be high speed motor with in-built or panel mounted VFD. The suction part of the blower shall be fitted with to avoid dust into the blower casing. The bottom of the blower assembly shall be provided with anti-vibration pads to subside vibrations generated during high speed operations. The Electric motor shall be permanent magnet or special high speed, horizontally mounted and further according to IEC Standard Type IE3 (High Efficiency) IP55. The power rating of the motor shall be 5.5 HP (4KW) with minimum permitted blower speed of 12000rpm, and maximum permitted blower speed of 18900 rpm. Rated industrial voltage of 380 to 480V and rated industrial frequency of 50 to 60Hz. and rated current of 8A. 6.AERATOR EXTERNAL ACCESSORIES shall have 2 numbers of floats of diameter 312mm and Length 2140mm. The MOC of the floats shall be of polypropylene with end plates welded to it. The floats shall have enough buoyancy volume to keep the entire structure of aerator afloat on the water surface. 20 nos. of suction extenders of suitable length shall be provided. 20nos. of seal rings shall be provided
132	On Grid Solar PV Plant comprising of: i) Solar panels of type Mono Crystline, PERC, etc. ii) Power Conditioning Unit (PCU)with MPPT, Inverter, Controls, Protection Devices, Interconnecting D.C. cables, Connectors, Junction Boxes and accessories. iii) D.C. D.B iv) A.C. D.B v) A.C. cables and accessories vi) Lightning arrestor, earthing, etc. vii) Module Metallic Mounting Structures viii) Installation, Testing and Commissioning corresponds to BIS and IEC requirements
133	Providing, supplying and installing high-quality floating trash boom system for riverfront development area, designed for interception and containment of floating debris, plastics and organic waste, comprising heavy-duty UV-stabilised PVC/TPU-coated reinforced polyester boom body, closed-cell HDPE/rotomoulded floats with adequate buoyancy, and flexible debris skirt of HDPE/polyester net extending below water surface, complete with galvanised / stainless-steel ballast chain to maintain vertical alignment, marine-grade connectors, tension cables and anchoring arrangements suitable for river flow conditions. The system shall be modular, highly visible, corrosion-resistant, capable of withstanding variations in water level and moderate current velocities, and shall include all materials, fabrication, transport, deployment, anchoring, testing and commissioning, complete as per approved design, drawings and directions of the Engineer-in-Charge.
134	Towards cost of Geophysical investigation survey charges.
135	Drilling of 150mm dia Borewell in Hard rock areas anywhere in Tamilnadu including transportation to the site in hard rock areas and developing the borewells
136	Supply and delivery of unplasticised ribbed screen PVC casing pipe of the 200mm dia with screwed and socket end and centering guide for every 15m length of pipes as per IS / 12818 / 92 and as amended from time to time to suit the borewell upto 150m depth (C.M) Casing medium with ISI marking including, loading, unloading, freight, stacking and transit insurance charges etc, complete. WD-M0031
137	Labor charges for inserting the P.V.C. casing pipes assembly with slots (or) without slots in the drilled holes including joining the pipes etc., complete, supply and packing the annular space with pebbles of size and quality as approved by the Municipal Engineer excluding cost of casing pipe etc., complete 200mm dia PVC casing pipe
138	Supply and delivery of THREE PHASE SUBMERSIBLE PUMPSET SUITABLE FOR 100MM DIA BOREWELL AS PER IS 8034/2002 WITHOUT PANEL BOARD Supply and delivery of clear water vertical wet type submersible pump suitable for 100mm dia borewell conforming to IS 8034/2002 as amended thereafter and BEE 3 Star Rated capable of discharging noted LPM against head of water column due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze or Cast SS impeller, brass screws and CI FG 200 grade pump bowl/diffuser with ISI mark. The pump shall be directly coupled to a continuos rated two pole suitable wet type vertical squirrel cage induction motor as per IS 9283 /1995 and as amended there after, suitable for operation in AC three phase 415 V+/- 10 %, 50 HZ +/- 5 % (350Lpm x 75 m head)
139	10 HP Submersible motor(350x75)WD-M1690
140	Supply and delivery of Star-Delta starter confirming to IS 13947, IEC60947-1 and as amended thereafter with suitable KW rating for operation in AC/ Three Phase/50HZ (+/- 5%) and 415V (+/- 10%) including 3 pole magnetic contactor with under voltage release - 3 nos., CT operated Ammeter (65 mm dia) with suppressed scale, Voltmeter (65mm dia), Voltmeter selector switch, Miniature circuit breaker, Thermal Overload relay, Air Break contactors suitable for next Standard higher KW rating, Single phasing preventor, dry running preventor and On/Off Push button switches, wiring with 1 sq.mm/4 sq. mm copper pvc insulated cable, powder coated vermin proof box, including the capacitor (the cost of capacitor is to be taken separately).
141	12.5 HP Panel board
142	Supply and Delivery of 2.5 Sqmm PVC insulated and Sheathed 3 Core flat type copper cable confirming to IS 694/1990 Including all charges with excise duty and handling charges etc WD-M1974
143	Towards Labour Charges for the errection of Submersible pump set in bore well including fixing and jointing submersible cable with proper clamps up to the starter to riser pipes to the required depth valves erection clamps, pressure gauge up to the exterior of panel board consisting of TPICN switches starter ,Volt meter, Ammeter, three pilot (indicating) Lamps capacitor single Phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., Complete and testing the pump set and trail run for 10 days WD-W0872
144	motor errection 10HP
145	Supply and delivery of 90mm dia HDPE PIPES - PE 100 AS PER IS 4984/1995 PN 16 with excise duty including cost & conveyance of all materials to site and all labour charges etc., complete
146	90mm HDPE Pipe
147	Supplying, laying and jointing G.I. Pipes of approved quality and best variety of “B” class pipe of the following dia including labour ﬁxing G.I. Specials, (excluding charges for cutting and threading of pipes, cost of such specials) to wall with necessary teak wood plugs, clamps, screws, thread balls, shellac, etc., making holes on the walls (or) drilling holes in roof and making good the dismantled portions to original condition with neceSORay brick work / concrete and plastering wherever neceSORy with necessary scaffolding charges. The pipes are to be painted with the 2 coats of good variety and approved best quality of synthetic enamel paint over a priming coat of red oxide etc., complete in all ﬂoors complying with standard speciﬁcation. G.I. pipes shall be got approved by the Executive Engineer before use on works - Internal water supply - Above Ground Level / External water supply - Above Ground Level
148	Supplying and ﬁxing in position ﬁrst quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard speciﬁcations (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.
149	Supply and delivery and fixing of HDPE tank as per IS 12701 / 1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc.,
150	Supplying PVC Specials in water supply arrangements (both in internal and external water supply arrangements Since the labour for cutting, threading / pasting, sundries have already been included under pipe line item of works, no separate provision for fixing UPVC specials needs to be allowed
151	Coupler25mm PVC Coupler
152	32mm PVC Coupler
153	50mm PVC Coupler
154	Elbow25mm dia Elbow
155	32mm dia Elbow
156	50mm dia Elbow
157	BEND25mm dia Pipe BEND
158	32mm dia Pipe BEND
159	50mm dia Pipe BEND
160	Tee25mm dia Tee
161	32mm dia Tee
162	50mm dia Tee
163	Union25mm dia Union
164	32mm dia Union
165	50mm dia Union
166	Reducer25 mm x 20 mm Reducer
167	32 mm x 25 mm Reducer
168	50 mm x 40 mm Reducer
169	Supplying and ﬁxing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of neceSORy PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and ﬁxing of cast iron gratings at junction of parapet and the RCC roof slab including ﬁnishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be ﬁxed in wall with special type of “U” clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard speciﬁcation and as directed by the departmental ofﬁcers
170	Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of Crushed stone sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three Crushed stone sand ) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)
171	Supplying and ﬁxing in position 15mm dia brass CP screw down tap / Pillar tap / Swan neck tap (heavy duty) of approved make conforming to BIS speciﬁcations and quality including cost of shellac, thread, etc., complete complying with standard speciﬁcation and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)
172	SD Tap
173	Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and ﬁxing PVC specials using PVC adhesives (but excluding cost of such specials) and ﬁxing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard speciﬁcations. The PVC pipes shall be got approved by Executive Engineer before use on works. - Internal water supply Above ground level.Internal Concealed Line
174	20mm dia
175	25mm dia
176	Supplying and ﬁxing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including ﬁxing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary ﬁttings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard speciﬁcations. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level
177	110mm dia
178	Supplying PVC Specials (with working pressure 6kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements (pwd sor p.no :102)
179	Coupler75 mm Dia pvc coupler
180	Elbow75 mm Dia pvc elbow
181	Tee75 mm Dia pvc Tee
182	Supplying and ﬁxing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double ﬂapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn,teak wood plugs, brass screws, etc., including supplying and ﬁxing 10 litres capacity PVC / 12.5 litres capacity porcelin low level ﬂushing tank with a pair of CI brackets, etc., complete with all ﬁttings such as 15mm brass ball valve with polythene ﬂoat with brass handle, union, coupling connected by means of 40mm white PVC ﬂush hand using Indian adopter joint including all internal ﬁttings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard speciﬁcations. (The EWC and ﬂushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)
183	Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications
184	Supply and ﬁxing in position of best Indian make white / colour glazed earthernware lipped mouth ﬂat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and ﬁxing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard speciﬁcations and as directed by the departmental ofﬁcers. (The urinal should be got approved by the Executive Engineer before use on works.)
185	CT METERING PANEL Fabrication, supplying, installation and commissioning of outdoor double door cubical feeder pillar of suitable size with locking arrangement in front & back with rain cap cover suitable for 3 phase, 4 wire 415 volt 50Hz dust and vermin proof made with CRCA sheet duly compartmentalized. and 4 strips 100A capacity aluminium bus bar with colour coded heat shrinkable insulation PVC sleeve with i/c providing & fixing following switch gears & accessories therein complete with connections, inter connections with suitable size ofaluminium strips / bars/ copper wires i/c powder coated with grey paint after 7 tank treatment, painting, two no’s earthing studs, suitable base frame fabricated with 50mmx 50mm x 5mm angle iron grouted in cement concrete so as to keep the feeder pillar 200mm above the ground level, cable allay and detachable gland plates at bottom, rubber gasket for doors with locking arrangement etc. complete as required. a) 63 Amp, 25kA, FP MCCB with spreader links, door interlock assembly & operating handle - 1 No (Incomer) b) 16Amps, DP 10kA DIN rail mounted MCB
186	CablesSupply and laying of following XLPE armoured LTUG cable in a trench/Tray with suitable cable tie tag etc as required.
187	Supply and Laying of 3 1/2 x 35 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.SD-669
188	Supply and clamping of following XLPE armoured LTUG cable on post or on wall MS-Clamps , Saddles, plugs, Screws etc., as required.
189	Supply and Laying of 4 x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.SD-667
190	Cable Gland - Supply and fixing of double compression brass cable gland for following Aluminium conductor XLPE insulated armoured cable of 1100 V grade with earth connection.
191	Supply and fixing of brass cable gland for 3-1/2 x 35 sq.mm. PVC armoured LTUG cable with earth connection SD-165
192	End Termination Supply and providing cable end termination of the following size PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (copper sockets for copper cables and Alu. Sockets for alum. Cable)
193	Supplyandprovidingcableendterminationof3-1/2x35sq.mm.PVCLTUGaluminiumarmouredcablewithnecessary aluminium cable sockets by crimping etc with electrical connection complete. SD-224
194	Outer Light Fitting Supplying and Fixing of Solar Street Light 1. Type: Monocrystalline or Polycrystalline2. Wattage: 100W 3. Voltage: 12V 1. Type: Deep Cycle Lead-Acid or Lithium-Ion2. Capacity: 100Ah 3. Backup Time: 12 hours LED Light1. Wattage: 30W 2. Lumens: 3000 lumens 3. Color Temperature: 5000K Controller1. Type: MPPT (Maximum Power Point Tracking) 2. Functions: Overcharge protection, over-discharge protection, and load control Pole1. Height: 6m to 12m 2. Material: Galvanized Steel or Aluminum 1. Motion Sensor: Automatic brightness adjustment based on motion detection 2. Dusk-to-Dawn Operation: Automatic on/off based on ambient light 3. Remote Monitoring: Optional remote monitoring and control
195	Supply of Kesslec 12W LED Bollard, BIS certified with a cylindrical steel pipe with a height of 500mm, permanently sealed optical block (IP66) with aluminium heat sink and a (IK10) PC protector. Highly efficient symmetric light distribution should provide excellent photometry between the bollards. Suitable for on ground mounting on 4xM10 bolts on 180mm PCD. System power of 12W, Overall system efficiency of 120lm/W at Correlated colour temperature (CCT) of 3000/4000K, colour rendering index (CRI) >70 and L70 rated lifetime of 50,000 hours. Electrical Class I, rated voltage 240Vac, Power Factor ≥ 0.95, with BIS certified potted driver having internal surge protection of 4/4 kV. The luminaire shall be in Matt Black colour and shall be supplied pre-cabled (0.3m) for easy installation. CAT REF: KESSLEC ANNA BOLLARD 500mm HT 12W LED or Equivalent
196	Supply of Kesslec 250W LED Flood light luminaire, BIS certified with a flat toughened glass protector (IK08), body of high pressure die cast aluminium, separate optical & control gear compartments (IP66) with a optical symmetric light distribution with 90° beam angle. Overall luminous efficiency of 120lm/W at correlated colour temperature (CCT) of 3000K/4000K, colour rendering index (CRI) >70 and L70 rated lifetime of 50,000 hours. Electrical Class I, rated voltage 240Vac, Power Factor ≥ 0.95, with BIS certified potted driver having internal surge protection of 4/4 kV and an additional surge protection device (SPD) of 10/10 kV (in both Common & Differential Modes). The luminaire shall be in Grey colour and shall be supplied pre-cabled (0.3m) for easy installation. CAT REF: KESSLEC SPARTA-F 250W 90DEG LED or Equivalent
197	Point Wiring - Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable color for Concealed PVC Light point / fan point (for electronic regulator) ( 4points / Coil) Higher End
198	Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection by 1 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable color for PVC concealed light (8 points per coil) (for rooms like bath, toilet & pumproom, etc.).
199	Wiring with 2 x 4 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 16A one way module switch and 1 no. 16A 3/2 pin module socket with module front plate with painting of Suitable color with continuous earth wire connection of 4 sq.mm copper wire for Open PVC pipe power Plug point ( 8 points / Coil) Higher End
200	Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion
201	Supply and Run of 3 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4 sq.mm copper wire and making good of the concealed position.
202	Sockets - Supply and fixing of 1no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Scope cover wall cutting , grouting , flushing and making good on the wall. Higher End.
203	Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Scope cover wall cutting , grouting , flushing and making good on the wall. Higher End.
204	Internal Light fittingsSupply and Fixing of 40W 4' LED Tube Light with PVC unsheathed copper leads from terminals to the fitting. (Make : Philips/Crompton/Havells )
205	Supply and construction of \\"I Love Tirchy\\" LED board selfie point uses IP65 waterproof SMD LED modules (P5 pixel pitch, ≥5000 nits brightness) in 3D acrylic/aluminum letters (2-4 ft high, 5-10 cm raised) on powder-coated MS frame, powered by 230V AC (50-100W/sq.m) with surge protection and remote/WiFi control for RGB scrolling text. Mount on RCC pedestal/wall at 8-12 ft height with anti-corrosion treatment, ventilation, and earthing; includes heart motif, 2-year warranty. Custom \\"I Love Tirchy\\" design per Tamil Nadu PWD .
206	Earthing Coil earth to street light poles with No.8 SWG GI wire of 11.5 metres of length in which 10 metres of total length compressed in to a coil of one meter length (75mm to 100mm dia) connected suitable with hexagonal earth bolt of size 8mm in to 25mm welded on the pole at one end with a coil position fixed on the earth
207	ESMP COST
208	Labour Camp establishment & facilities
209	Workers’ EHS Measures (PPE, health camps, sanitation)
210	Barricading - Construction Zone Barricades, Edge Protection Along Riverbanks, Public Safety Barricades, Water Safety Barriers.
211	Debris disposal – Disposal of C&D waste with one way lead.
212	Dust suppression at construction area, stock yards & material handling and places adjacent to the labour camp.
213	Traffic diversion costs includes provision of temporary road infrastructure, barricading, safety systems, signage, lighting, maintenance of diversion routes and coordination with local traffic authorities, traffic marshals and Monitoring & Compliance for smooth traffic flow for ensuring safety of pedestrians during construction.
214	EHS/OHS provisions including site safety infrastructure, adequate PPE, health facilities, emergency response & preparedness including ambulance, inflatable crafts & shackles, lifebuoy, etc., and maintaining work & labour camps as per National norms.
215	Consents for Establishment (RMC, DG sets, other approvals).
216	Total cost of operation and maintenance of the Water Supply system including manpower, spares, consumables, repair work etc.
217	For First Year
218	For Second Year
219	For Third Year
220	For Fourth Year
221	For Fifth Year
222	Construction Phase Monitoring
223	Ambient Air Quality (PM₂.₅, PM₁₀, SO₂, NOx)
224	Surface Water Quality (pH, EC, DO, BOD, Coliforms, SAR, RSC, etc.)
225	Ground Water Quality (pH, EC, Hardness, NO₃, SO₄, Cl, F, Fe, etc.)
226	Noise Levels – Leq dB(A) (Day/Night)
227	Soil Quality (pH, EC, OC, NPK, CEC, Metals)
228	Capacity Building & Awareness
229	Capacity Building –PIU/PMC/ Contractor/workers) Training
230	Community Awareness Campaigns / IEC
231	O&M Monitoring
232	Surface Water Quality (O&M)
233	Ground Water Quality (O&M)
234	Soil Quality (O&M)
235	Plantation Survival Monitoring Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents
5	Click here to download tender document	Tender Documents
6	Click here to download tender document	Tender Documents
7	Click here to download tender document	Tender Documents
8	Click here to download tender document	Tender Documents
9	Click here to download tender document	Tender Documents

Also Visit

Tenders

Tamil Nadu Tenders

Services Tenders

Business Management Services Tenders

Detail Project Report Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Detailed Project Report For Proposed Kottapattu Lake Development At Tiruchirappalli City Corporation, Tiruchirappalli-Tamil Nadu

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Detailed Project Report For Proposed Kottapattu Lake Development At Tiruchirappalli City Corporation, Tiruchirappalli-Tamil Nadu

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us