|
| 1 | Demolition and breaking of SGSW or RCC drain/Soil pipes jointed in cement mortar and taking out from trenches if required internal diameter 150mm. |
| 2 | Demolition of brick wk masonry built in cement mortar incldg all quoins arches pillars etc |
| 3 | Demolition of reinforced cement concrete of any description in any position not otherwise described complete. |
| 4 | Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) |
| 5 | Taking down cement plaster on wall of any description incl racking out joints hacking for key and scrubbing down with water complete. |
| 6 | M & L for 75 mm thick PCC 1:3:6 type C-2 using 20mm graded stone aggregate including finished surface even & fair without using extra cement as in plinth protection including necessary form work of edge all as specified and directed. Note: 10mm wide and 75mm deep joints shall be made at 3 mtr intervel and at each corner and the same shall be filled with using bitumen 85/25 and sand in the ratio 1:3. |
| 7 | M&L pre cast RCC (1:1.5:3) type A-1 as in manhole cover, drain cover and set in cement mortar (1:4) including necessary formwork complete. |
| 8 | M&L brick work with sub class 'B' brick straight or curved on plan exc 6 metres radius with old size bricks built in cement mortar (1:4) complete. |
| 9 | M&L Brick work with sub class 'B' Brick straight or curved on plain to any radius in half brick thick wall built in cm 1:4 |
| 10 | M&L PCC 1:3:6 and type C2 using 40mm graded stone agregate for concrete bed to drain pipes including packing under hunching against the sides of pipes after they laid and tested for 150mm dia pipes |
| 11 | M&L cement concrete (1:4:8) type D2 using 40mm graded stone aggregate in fondation and mass concrete for manhole surface channels and drains |
| 12 | M&L Salt-glazed stone ware drain (SWSG) pipe grade 'A' 150 mm dia laid in trenches & jointed in CM 1:1 and tested complete all as specified. |
| 13 | M&L PCC (1:2:4) type B1 using 20mm graded stone aggregate in coping etc, including weathering slightly rounded champers angle forming channels & form work |
| 14 | M&L mild steel TMT bar 8mm dia cut length cut to length bent to shape required including cranking bending and binding with MS wire not less than 0.9mm diaor securing clips |
| 15 | M&L rendering 15mm thick cement mortar (1:4) on fair faces of brick or concrete surfaces and finished even and fair without using extra cement. |
| 16 | Cutting into existing manholes for connecting new drains making good to pipes and rendering, cutting existing benching for forming branch channel etc for 150mm pipes. |
| 17 | Cleaning and dewatering of Septic tank by any means & getting out and removing the sludge to a distance not exc 250m and disposal of the same in approved low lying areas complete as required by EIC. capacity of tank 50 users |
| 18 | Description all as per Ser item No 17 above but of capacity 150 users |
| 19 | Description all as per Ser item No 17 above but of capacity 500 users |
| 20 | Dewatering of soak well/Soak pit by pumping out and discharging the water away using suitable discharge, digging katcha channel for flow of water and making good of the same, all as specified and directed by EIC. dia (internal) exc 1.2m and n exc 1.8m and depth up to 3m. |
| 21 | Description all as per Ser item No 20 above but dia (Internal diameter) exc 1.2m and n exc 1.8m and depth exc 3m and n exc 4.50m. |
| 22 | Description all as per Ser item No 20 above but dia (Internal diameter) exc 1.8m and n exc 2.40m and depth exc 3m and n exc 4.50m. |
| 23 | S&F in repairs 110mm dia, PVC (SWR) Pipes single socketed in any length with rubber rings joints land in trenches or floor and making good the surface all as specified and directed by the EIC. |
| 24 | S&F in repairs 110mm dia, PVC (SWR) Pipes single socketed in any length with rubber rings joints fixed to walls all as specified and directed by the EIC. |
| 25 | S&F in repairs 75mm dia, PVC (SWR) Pipes single socketed in any length with rubber rings joints fixed to walls all as specified and directed by the EIC. |
| 26 | S&F PVC (SWR) vent cowl, 110 mm dia |
| 27 | S&F PVC (SWR) bend, 110 mm dia |
| 28 | S&F PVC (SWR) junction single, (Single T) equal or unequal 110mm dia |
| 29 | S&F PVC (SWR) bend, 75 mm dia |
| 30 | S&F PVC (SWR) junction single, (Single T) equal or unequal 75mm dia |
| 31 | M&L forming fair finished drain or channel, 30 cm inner girth, cement concrete finished even and smooth, using extra cement including forms moulds etc. |
| 32 | Cleaning of blockage of WCs , bath room, blockage of sewage pipe line any dia, manhole etc. as per day to day complain by rodding or by any meachanical cleaning equipment all as specified and directed by Engr in charge. (Note: Measurement will be taken from one manhole/gully trap to another manhole/gully trap) |
| 33 | S&F in repair vitreous china squatting pan, Orrissa pattern size 580x440mm white with PVC 'P' or 'S' trap with integral foot rest of any pattern incl connection to trap & to flushing pipe, antisyphonage pipe etc making good to floor complete. |
| 34 | S&F in repair Vitreous china wash down water closet pan ( pedestal pattern), white (excluding fixing bolt, flushing cistern and flush pipe) but including P or S trap, sheet cover of white colour all as directed and specified. |
| 35 | S&F in repair vitreous china wash hand basin, white, flat back, size 550x400 mm incl chain and plug and porcelain stopper, brackets, waste pipe incl cutting for and pinning in ends of brackets or erecting stand including dismantling |
| 36 | S&F in repair PVC flushing cistern 10 ltr capacity including bracket fixed to wall & flush pipe complete ISI marked |
| 37 | S&F in repair, plastic water closet seat cover, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device for pedestal pattern WC, black/ white colour. |
| 38 | Taking up or steel tubing & connections including cleaning for refixing bore of pipe 15mm etc complete all as specified and directed |
| 39 | Taking up or steel tubing & connections including cleaning for refixing bore of pipe 20 mm etc complete all as specified and directed |
| 40 | S&F tubes medium grade galvanised with all fittings & fixed complete to walls & ceiling or laid in floors 15mm bore etc complete all as specified and directed |
| 41 | S&F tubes medium grade galvanised with all fittings & fixed complete to walls & ceiling or laid in floors 20mm bore etc complete all as specified and directed |
| 42 | Supply & fixing in repairs rotational moulded polyethylene water storage tanks 500 liters capacity, (cylindrical, vertical in closed top) three layered hoisted and fixed in position with all fittings all as specified including 20 mm PVC ball valve including dismantling existing water tanks complete all as specified & directed. |
| 43 | Supply & fixing in repairs rotational moulded polyethylene water storage tanks 1000 liters capacity, (cylindrical, vertical in closed top) three layered hoisted and fixed in position with all fittings all as specified including 20 mm PVC ball valve including dismantling existing water tanks complete all as specified & directed. |
| 44 | S&F in repair for Gun-metal, globe or gate valves 20mm, with iron wheel head, screwed both ends for iron pipe etc comlete all as specified and directed . |
| 45 | S&F in repair for Gun-metal, globe or gate valves 15mm, with iron wheel head, screwed both ends for iron pipe etc comlete all as specified and directed . |
| 46 | S&F in repair bib tap 15mm fancy type of PTMT any colour high pressure screwed for iron pipe and fixed complete all as specified and directed . |
| 47 | S&F in repair bib tap 15mm chromium plated fancy type long shank with crutch butterfly handle, screw down screwed for iron pipe or for brass ferrule etc complete all as specified and directed . |
| 48 | S&F in repair stop valve 15mm chromium plated screw down, high pressure with crutch or butterfly handle, screwed fboth ends for or iron pipe or for unions and fixed complete all as specified and directed |
| 49 | S&F in repairs IVC hand shower (Health faucet) with 8mm dia, 01 (one) metre long PVC tube and wall hook with plastic body complete all as specified & directed. |
| 50 | S&F in repairs 15mm dia pillar tap cost copper alloy fancy type with capstan heads chromium plated screwed down high pressure with or without letered \\"Hot or Cold\\" high pressure with long screwed shanks & fly nuts screwed for iron pipe etc complete all as specified and directed |
| 51 | S&F in repairs 15 mm dia concealed type stop valve fancy type chromium plated etc complete all as specified and directed |
| 52 | S&F in repair Brass chromium plated shower rose 125mm size fancy type with or without swelves joint fixed to iron pipe etc complete all as directed and spd. |
| 53 | S&F in repairs looking mirror 600x450mm selected quality 5mm thick glass mounted on 6mm ply wood & fixed with brass screw & cup washer |
| 54 | S&F in repair PVC connection 450mm long with two PTMT nuts |
| 55 | S&F in repair CP towel rail, 20mm dia, D type,60cm long complete all as approved and directed by the EIC |
| 56 | S&F in repair 32mm bore waste coupling of PTMT (half or full threaded) (Min wt 45 gms) Complete. |
| 57 | S&F in repair 32mm bore low density polyethylene (LDPE) pipes of pressure rating 6kgf/sqcm Complete. |
| 58 | M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete. |
| 59 | Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete. |
| 60 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete. |
| 61 | M&L Cement concrete 1:5:10, type E-2 (using 40 mm graded stone aggregate) as in sub base etc complete |
| 62 | M&L Cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in levelling course, coping, etc complete. |
| 63 | M&L for joint free non skid coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc incl 15mm thick screed bed in CM 1:4, set & jointed in neat cement slurry and pointed with white or coloured cement to match complete |
| 64 | M&L coloured ceramic glazed tiles 300x200x6mm thick as in dado/skirting etc incl 10 mm thick rendering in CM 1:3, set & jointed in neat cement slurry & pointed in white or coloured cement slurry & pointed in white or coloured cement |
| 65 | M&L for joint free non skid coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc over & including 15mm thick screed bed in CM 1:4, set & jointed in neat cement slurry and pointed with white or coloured cement to match complete |
| 66 | M&L coloured ceramic glazed tiles 450x300x7mm thick as in dado/skirting etc including 10 mm thick rendering in CM 1:3, set & jointed in neat cement slurry & pointed in white or coloured cement slurry & pointed in white or coloured cement. |
| 67 | Cleaning and removing all scale and dirt etc by using bleaching powder from water tank and from mouth of circulating pipe,etc Capacity of tank n exc 250 litrres |
| 68 | Description all as per Ser Item No 67 above but Capacity of tank exc 250 litres & n exc 500 litres |
| 69 | Description all as per Ser Item No 67 above but Capacity of tank exc 500 litres & n exc 1000 litres |
| 70 | S&F in repair PVC ball valve 15mm dia with epoxy coateed aluminium rod and high density ball (minium weight 142 gms) complete as directed by Engr-in-charge. |
| 71 | S&F in repair PVC ball valve 20mm dia with epoxy coateed aluminium rod and high density ball (minium weight 210 gms) complete as directed by Engr-in-charge. |
| 72 | Dismantling AC/CGI/translucent (corrugated or semi corrugated ) sheets in roof covering |
| 73 | Dismantling of timber scantling 40 Sqcm and over in section in any position complete. |
| 74 | Dismantling of roof trusses , purlin, rails & fastening etc, of steel section complete. |
| 75 | M&L roof trusses (framed), trusses, purlins, rails & fastening and heavy bracket framing (beam, tee, angle, channel, flat, etc) incl distance pieces, cleats, holdfast etc complete all as spcd & directed. |
| 76 | Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, chhaja,etc, fixed with self tapping screws as specified |
| 77 | Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 78 | Material & labour for 6 mm thick asbestos cement corrrugated sheets fixed with' L' or 'J' type or cranked hook bolts as in roof complete all as specified & directed. |
| 79 | Material & labour for 6mm thick asbestos cement two piece serated ridge fixed with 'L' or 'J' type or cranked hook bolts complete all as specified & directed. |
| 80 | S&F Mild steel flat iron as in wind ties including cutting drilling holes and securing bolts confirming to FE 410-0 of 310-0 complete |
| 81 | Dismantling Wall and ceiling boards of any description and any thickness including cover fillets. |
| 82 | M&L providing aluminum snap Grid frame work for false ceiling with of size 595x595 mm, using main and cross Tee of size 36.5 mm x 25mm x 1.4 mm, weighing 0.24 Kg/RM and 23.5mm x 26.4mm x 1.4mm weighing 0.191 Kg/RM respectively. The snap grid shall be supported at end all along the wall with alu anodized angle of size 40 mm x 25 mm x 2 mm weighing 0.36 Kg/RM . the snap grid shall be fixed to ceiling supporting hangers consisting of 2 mm dia MS wire, J bolts, nuts and washers as per manufacturer's instructrions. |
| 83 | M&L 4mm thick Non asbestos fibre designer cement building boards fixed or laid/inserted to timber/GI/Aluminium framework with screws . |
| 84 | Material & labour 15mm thick rendering in CM 1:6 on fair fair faces of brick wall or concrete surfaces finished even and fair complete all as specified |
| 85 | Materials & labour for prepration of newely plastered surfaces of wall and applying two coat of Oil Bound distemper on walls, white or tinned over a coat of chalk whiting complete all as specified & directed. |
| 86 | M&L vitrified coloured ceramic tiles 10 mm thick (square or rectangular) polished, area of each tiles not exceeding 0.36sqm, in floors etc over and including 15mm thick screed bed in CM 1:4 set and jointed in neat cement slurry and pointed in white or colored cement to match complete. |
| 87 | Description all as per Ser item No 86 above but as in Skirting with 10mm thick rendering in CM 1:3 |
| 88 | M&L machine cut kota stone slab flooring 18-20mm thick over & including 20mm screed base in CM 1: 4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. |
| 89 | Description all as per Ser item No 88 above but as in Skirting with 10mm thick rendering in CM 1:3 |
| 90 | M&F for 25 mm thick PCC (1:2:4) type B-0 (Using 12.5mm graded stone aggregate) as in sub base of floor complete all as specified & directed |
| 91 | M&L 20mm thick Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in CM(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of pigment |
| 92 | M & L, 15mm thick rendering on fair faces of brick work/concrete surface in CM (1:4) with applying water proofing compound (As per manufrature instruction) surface finished fair & even complete.(WPC will be paid saperatelly) |
| 93 | M&L for applying Two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 ltr/10sqm over and including priming coat of exterior primer applied @ 0.90 ltr/10sqm over a coat of plaster of paris putty of 1mm thickness after complete removal of existing treatment on wall surfaces. |
| 94 | Supply only liquie water proofing compound as per manufacture instruction. |
| 95 | Materials & labour for complete removal of existing treatmemt and finishing the surfaces of wall with two coats of cement base paint of, any colour, complete all as specified & directed. |
| 96 | M&L for applying Two of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company depot tinted) with silicon additives @ 1.43 ltr/10sqm over and including priming coat of exterior primer applied @ 0.90 ltr/10sqm over a coat of wall putty on new plastered wall surfaces incl preparation. |
| 97 | M&L for GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre incl 2mm dia G.I. ( upto 1200 mm length ) adjusting level to Purlins/ Rafter. . |
| 98 | Disconnecting 500 Ltrs existing tanks, setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting and re-fixing in position and Cleaning and removing all scales and dirt algae, fungus etc from RCC/PVC water tanks and from mouth of pipes with bleaching powder etc after dewatering/draining water and removing vegetation around the tanks for the following tank capacities including writing with paint the date of cleaning on the tank. |
| 99 | Disconnecting 1000 Ltrs existing tanks, setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting and re-fixing in position and Cleaning and removing all scales and dirt algae, fungus etc from RCC/PVC water tanks and from mouth of pipes with bleaching powder etc after dewatering/draining water and removing vegetation around the tanks for the following tank capacities including writing with paint the date of cleaning on the tank. |
| 100 | S&F in repair 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. |
| 101 | M&L in repairs 75mm dia of outlet PVC (SWR) floor trap, plain with grating including jointing with solvent cement. |
| 102 | S&F 32 mm bore dia of dishcharge pipe Waste coupling of PTMT(half or full threaded) (Minimum weight 32mm- 45gms/40mm-60 gms) |
| 103 | S&F in repair 15mm dia Angle valves, cast copper alloy, chromium plated fancy type screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified. |
| 104 | S&F in repair sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified. |
| 105 | S&F in repair CP Health fauset with 1 Meter PVC Tube and hook . |
| 106 | M & L for preparing old plastered surfaces of wall and and applying one coat of distemper oil emulsion, white or tinted complete all as directed. |
| 107 | Description all as per Ser item No 106 above but on ceiling |
| 108 | Complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces and preparation of surfaces for further treatment and applying two coats of distemper, oil emulsion white or tinted complete. |
| 109 | M & L for complete removal of existing treatment over wall and applying two coats of distemper oil emulsion over 2mm thick wall care putty complete all as directed |
| 110 | M & L, 10mm thick rendering on fair faces of brick work/concrete surface in CM (1:6) surface finished fair & even complete. |
| 111 | M&L for preparation of new plasterd wall surfaces and applying two coat of oil bound distemper of approved colour and shade over one coat wall care putty . |
| 112 | M&L for preparation of old wooden surface of any description over 10 cm width or girth and applying one coat of synthetic enamel paint white or tinted complete all as directed. |
| 113 | Description all as per Ser item No 112 above, but applying two coat of synthetic enamel paint white or tinted complete all as directed. |
| 114 | M&L for preparation of old painted steel surface of any description , over 10 cm width or girth not otherwise described and applying one coat of synthitic enamel paint white or tinted all as directed. |
| 115 | S&F in repair Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing |
| 116 | S&F in repair 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing. |
| 117 | S&F 5mm thick PVC sheet Plain Embosed including powder coated Aluminium 'T' section (Size 25mm X 25mm, Heavy) and angle 'L' (Size 25mm X 25 Heavy) including all fitting etc. required as per specification for false ceiling. |
| 118 | Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exc1.5 Sqm but n.exc 4.00 Sqm each and removing from site . |
| 119 | Taking down chowkats or frames with shutters (without taking off shutters from the frame) area n’exc1.5 Sqm and removing from site . |
| 120 | S&F as in hold fasts; conforming to Fe -290 Gde E-165 complete. |
| 121 | M&L for Pressed steel frames 125 x 60 mm size of frame for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete |
| 122 | M&L for Pressed steel frames 105 x 60 mm size of frame for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete. |
| 123 | S&F 2nd class hard wood 30 mm thick glazed & skelton shutter (any no of pannel) open rebated and prepared to receive glass, gauge etc with sush bar edges to framing plain chamfered or receive glass gauge etc with sash bar edge of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass etc size of member of shutter as specified in SSR Part-I section 8 clause 8.24 (a). |
| 124 | S&F particle board core factory made solid PVC Moulded door shutter 28 to 30mm thick (stiles) with 2 mm thick Moulded PVC sheet on the front face & 2 mm plain colour PVC sheet on back faces,and with particle Board Core supplying and fixing in frame at site as per specification and drawing. |
| 125 | S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, in opening as per specification and shown on drg in SSR Part-II 2004 complete all as specified and as directed. |
| 126 | S&F, factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rails, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and jointed together with solvent cement, in the frame at site as per specification and shown on drawing in SSR Part-II (2004) . |
| 127 | S & F 100 mm Butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 . |
| 128 | S&F 150 mm long aluminium anodised barrel tower bolt of extruded section complete. |
| 129 | S&F of 150 mm size aluminium handles cast type anodised. |
| 130 | M&L, applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of newly steel surfaces of any description over 10cm width or girth not otherwise described. |
| 131 | S&F 18 mm thick Rajshree Celuka ply or equivalent as approved of grade 1 quality with both side plain white or coloured fixed with stainless steel screwes, solvent cement /adhesive to fabricate kitchen cabinet sides , top and bottom, door, shelf inside the cabinet and drawer including ,drawer chanel, magnetic ballcatch & other all fittings complete all as per manufacturers instructions incl taking out old existing wooden cabinate. |
| 132 | S & F Floor door stopper of aluminium alloy body and tongue, anodized, with hand drawn steel spring fixed in door, overall length of cover plate 150 mm |
| 133 | S&F powder coated anodised/aluminium frame of size 65mm x 38mm x 1.00 thick or appropriate section as directed including with frame standard section for sliding type windows /ventilatorss with one or more rebates including joining cleats, beading, handle with locking arrangement, rubber gasket for fixing etc complete with and including 5.5 mm thick tinted glass n.exc 1 Sqm each panes (window of frame 3 tract wt not less than 0.50kg/RM and shutter having wt not less 0.45kg/RM) all as specified and directed |
| 134 | S&F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified |
| 135 | Powder coated aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary oining cleats, glazing clips, rubber packing, anodised aluminium snap eading, screws etc. complete all as specified |
| 136 | S & F 4 mm thick frosted glass pin head type and glazing with oil putty in squares exc 0.5 Sqm in each pane etc complete all as spd and directed. |
| 137 | M&L for Stainless Steel wire cloth for 0.56 mm nominal dia of wire & average width of aperture 1.18mm fixed with tinned tacks or galvanised wire staples etc |
| 138 | S&F in repair Harrison rails (Curtain rails), mild steel, chromium plated including with supply & fixing brackets, stops, rollers with endcaps etc. |
| 139 | S&F 100 mm size butt hinges of medium weight cold rolled mild steel |
| 140 | S&F extruded steel alloy handles, fabricated type, size of handle 150 mm, |
| 141 | S&F steel alloy 200mm long barrel tower bolts of extruded section, |
| 142 | S&F steel alloy, slidnig door bolt with hasp and staple and fixing clips of sheet, cast or extruded section, and fixing bolts and sliding bolts of electrogalvanised plate and bright bolt and fixed length of bolt 300 mm. |
| 143 | S&F mild steel 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete |
| 144 | S&F in repair door closer hydraulically regulated, designated No- 2 universal type, suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 kg aluminium (die cast) body. |
| 145 | S&F door closer hydraulically regulated, designated No- 2 universal type, suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 kg aluminium (die cast) body. |
| 146 | S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed |
| 147 | S&F floor door stoper of brass body and tongue, anodised with hard drawn steel spring over all length of cover plate 140 mm complete all as specified and directed. |
| 148 | Description all as per Ser item No 147 above but figured glass pin headed type n.exc 0.50 sqm each complete. |
| 149 | M&L Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to fe.290.Gde-E-165 |
| 150 | S&F in repairs mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete Please Enable Macros to View BoQ information |
