|
| 1 | MATERIALS AND LABOUR ETC.(C)-(II) COST OF MATERIALS 17.(A) Sypply of E.R.W.M.S.(Electrical Resistant Welded M.S.) black pipe of of TATA make (heavy quality) as per standard specification, having wall thickness not less than 8 mm.(ii) 300 mm dia. (internal) N.B. The rates for supply of non TATA but I.S.I. marked G.I. pipes and fittings will be arrived at by reducing the corresponding rates for TATA pipes and fittings by 20%. |
| 2 | CHAPTER - VIII SUPPLYING OF MATERIALS 8.8 Ductile iron double flanged manually operated sluice valve generally conforming to IS : 14846, having body, door, dome, gland in graded ductile iron to IS 1865, four faces and spindle nut of gun metal to IS : 318, inside screw non- rising stainless steel AISI-410 spindle valves suitable formaximum working pressure of 10 kg/cm... and body tested 15 kg/cm..., flanges flat faced and drilled to IS: 1538 :1993. Valves tested by closed end method only. 350mm and above valves are complete with enclosed gear box with anti friction device.Diameter in mm 300 |
| 3 | CHAPTER - VIII SUPPLYING OF MATERIALS Supply of M.S. Flange (slipper type) as per IS-6392 TABLE 17 Thickness - 20mm -22mm NB Diameter in mm 300 |
| 4 | CHAPTER - VIII SUPPLYING OF MATERIALS Supply of M.S. Flange (slipper type) as per IS-6392 TABLE 17 Thickness - 20mm -22mm NB Diameter in mm 150 |
| 5 | MATERIALS AND LABOUR ETC.(C)-(II) COST OF MATERIALS 17.(A) Sypply of E.R.W.M.S.(Electrical Resistant Welded M.S.) black pipe of of TATA make (heavy quality) as per standard specification, 5 mm thick. (ii) 150 mm dia. (internal) N.B. The rates for supply of non TATA but I.S.I. marked G.I. pipes and fittings will be arrived at by reducing the corresponding rates for TATA pipes and fittings by 20%. |
| 6 | CHAPTER - VIII SUPPLYING OF MATERIALS Supply of M.S. Flange (slipper type) as per IS-6392 TABLE 17 Thickness - 20mm -22mm NB Diameter in mm 100 |
| 7 | CHAPTER - VIII SUPPLYING OF MATERIALS M.S. blank Flange as per IS-6392 TABLE 20 for 50 mm to size & for 200mm & above as IS -6329 Table-14)thickness 20mm-22mm NB Diameter in mm 300 |
| 8 | PLUMBING WORKS (A)-(II) G.I. PIPE WORKS AND FITTINGS 9. C.I. sluice valve with flanged ends drilled to as per I.S. 1358/62 and having all cast iron components as per I.S. 780/71 solid forged bronze inside screw spindle having ultimate tensile strength not less than 4.72 MT per sq. cm. Spindle nut valve and seat faces of hard wear resisting, manufactured from best quality gunmetal conforming to I.S. 780/71, painted black all over with asphalt base paint tested to 21 kg (hydraulic pressure) per sq. cm., valve opening to anticlockwise direction, fitted and fixed complete. (iii) 100mm |
| 9 | PLUMBING WORKS (A)-(II) G.I. PIPE WORKS AND FITTINGS 9. C.I. sluice valve with flanged ends drilled to as per I.S. 1358/62 and having all cast iron components as per I.S. 780/71 solid forged bronze inside screw spindle having ultimate tensile strength not less than 4.72 MT per sq. cm. Spindle nut valve and seat faces of hard wear resisting, manufactured from best quality gunmetal conforming to I.S. 780/71, painted black all over with asphalt base paint tested to 21 kg (hydraulic pressure) per sq. cm., valve opening to anticlockwise direction, fitted and fixed complete. (v) 150 mm |
| 10 | CHAPTER - VIII SUPPLYING OF MATERIALS 8.9 Cast iron double flanged single door swing Non-Return Valve generally conforming to IS 14846 having body, door cover in graded cast iron to IS 210 Gr. FG 200, body and door rings and bearing block of leaded tin bronze to I.S 318 Gr. LTB 2, hinge pin of ST AISI410 valves suitable for maximum working pressure of 10 kg/cm... and body tested 15 kg/cm.... Diameter in mm 150 |
| 11 | CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.4Valves 2.4.1 Lowering, fitting and fixing of all types of valves in proper position and alignment using chain pully block or crane(for diameter above 250 mm) by providing temporary support,as required,gaskets,nuts& bolts etc.all cornplete as per specification and direction of the Engineer-in-Charge.[The rate Includes cost of flange joints]300mm dia. |
| 12 | CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.4Valves 2.4.1 Lowering, fitting and fixing of all types of valves in proper position and alignment using chain pully block or crane(for diameter above 250 mm) by providing temporary support,as required,gaskets,nuts& bolts etc.all cornplete as per specification and direction of the Engineer-in-Charge.[The rate Includes cost of flange joints]150mm dia. |
| 13 | CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.1.6 Flange joint to C.l./D.l/MS. pipes and specials including supply of rubber gasket. nuts. bolts. washers etc. of best quality to make the joint watertight at required hydraulic pressure all complete as per specification & direction of the Engineer-in-Charge. Diameter in mm 100mm dia. |
| 14 | CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.1.6 Flange joint to C.l./D.l/MS. pipes and specials including supply of rubber gasket. nuts. bolts. washers etc. of best quality to make the joint watertight at required hydraulic pressure all complete as per specification & direction of the Engineer-in-Charge. Diameter in mm 150mm dia. |
| 15 | CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.1.6 Flange joint to C.l./D.l/MS. pipes and specials including supply of rubber gasket. nuts. bolts. washers etc. of best quality to make the joint watertight at required hydraulic pressure all complete as per specification & direction of the Engineer-in-Charge. Diameter in mm 300mm dia. |
| 16 | CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.3 M.S. Pipes 2.3.1 Gas cutting of M.S. pipes and/or M.S. plates of different thickness all complete as per specification and direction of the Engineer-in- Charge. Thikness in mm 5mm to 8mm thick plate |
| 17 | CHAPTER - VIII SUPPLYING OF MATERIALS 8.16Sypply of E.R.W.M.S. (Electrical Resistant Welded M.S.) black pipe of ISI mark as per relevent IS Specification ( heavy quality ) having wall thick-ness not less than 8 mm. [N.B.: The rates for supply of TATA Make pipe will be arrived at by adding 20% of the corresponding rates ] Diameter in mm (Internal) 200 |
| 18 | CHAPTER - VIII SUPPLYING OF MATERIALS Supply of M.S. Flange (slipper type) as per IS-6392 TABLE 17 Thickness - 20mm -22mm NB Diameter in mm 200 |
| 19 | CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.1.6 Flange joint to C.l./D.l/MS. pipes and specials including supply of rubber gasket. nuts. bolts. washers etc. of best quality to make the joint watertight at required hydraulic pressure all complete as per specification & direction of the Engineer-in-Charge. Diameter in mm 200mm dia |
| 20 | CAST IRON DOUBLE FLANGED RIING SPINDLE SLUICE VALVE GENERALLY CONFIRMING TO IS 14846 HAVING BODY DOOR/ DOME/ BONNET AND COVER OF CAST IRON GR FG 260, OUTSIDE SCREEN RISING SPINDLE OF IS 6603 GR-12 CR-13, SPINDLE NUT & SEAT RINGS ARE GUNMETAL AS PER IS:318 LTB2. FLANGES FLAT FACED AND DRILLED TO IS:1538 PART IV & VI, VALVES ARE SUITABLE FOR MAXIMUM WORKING PRESSURE OF 10/16 KG/SQCM (SEAT TEST) AND BODY TESTED TO 15/24 KG/SQCM 350 NB AND ABOVE VALVES SHOULD BE PROVIDED WITH ENCLOSED GEAR BOX AND ANTIFRICTION DEVICE FOR EASE OF OPERATION. ALL THE VALVES SHOULD BE TESTED BY CLOSED END MRTHOD ONLY. SIZE 200 MM PN RATING 1.6. WBPHED/SOR/ME/2019. |
| 21 | CAST IRON DOUBLE FLANGED SINGLE DOOR SWING NON-RETUEN VALVE GENERALLY CONFIRMING TO IS:5312 PART I, HAVING BODY, COVER IN GRADED CAST IRON TO IS:210 GR.FG200, BODY AND DOOR RINGS & BEARING BLOCK OF LEADED TIN BRONZE TO IS:318 GR.LTB 2 (350MM & ABOVE), HINGE PIN OF ST.ST.AISI410, VALVE SUITABLE FOR A MAXIMUM WORKING PRESSURE OF 10/16 KG/CM2 (SEAT TEST) & BODY TESTED TO 15/24 KG/SQCM. SIZE-200 MM, PN RATING 1.6.WBPHED/SOR/ME/2019 |
| 22 | CHAPTER - II LAYING & JOINTING PIPES, SPECIALS ETC.2.1 C.I. / D.I. Pipe & Specials 2.1 C.I. / D.I. Pipe & Specials 2.4Valves 2.4.1 Lowering, fitting and fixing of all types of valves in proper position and alignment using chain pully block or crane(for diameter above 250 mm) by providing temporary support,as required,gaskets,nuts& bolts etc.all cornplete as per specification and direction of the Engineer-in-Charge.[The rate Includes cost of flange joints]200mm dia. |
| 23 | MATERIALS AND LABOUR ETC.(C)-(II) COST OF MATERIALS 17.(A) Sypply of E.R.W.M.S.(Electrical Resistant Welded M.S.) black pipe of of TATA make (heavy quality) as per standard specification, 5 mm thick. (i) 100 mm dia. (internal) N.B. The rates for supply of non TATA but I.S.I. marked G.I. pipes and fittings will be arrived at by reducing the corresponding rates for TATA pipes and fittings by 20%. |
| 24 | BUILDING WORKS (F) STRUCTURAL STEEL WORKS, GRILLS, GATES ETC. B. REPAIRING 2. Welding in M.S. structural work with gas or electric: (b) Continuous weld. |
| 25 | CHAPTER - VIII SUPPLYING OF MATERIALS HIRE CHARGES OF MACHINERIES 8.26 Hire charges of moveable crane with fuel & manpower having load handling capacity upto 14MT with the 45 deg. moveable arrangement & the boom length of 40 feets for loading & unloading of various materials / accessories of water supply works. For minimum engagement of 8 hrs. In a day |
| 26 | BUILDING WORKS (F) STRUCTURAL STEEL WORKS, GRILLS, GATES ETC. A. ORIGINAL WORKS 1. M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-incharge complete including cutting to requisite shape and length,fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1969 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc. Payment to be made on the basis of calculated weight of structural members only in finished work as per IS specified weight. Payment for gusset, bracket, cleat, rivets, bolts and nuts may be make by adding the actual weight of such items with the weight of finished structural members or 7% of weight for finished structural members weighing not less than 22.5 Kg. / m. or 15 % of weight for finished structal members weighing less than 22.5 Kg. / m. may be increased allow for bracket, cleat, rivet, bolts and nuts etc. and no seperate payment being made for these items, as per direction of Engineer In Charge. The rates are considered for a height of erection 8m. / 2nd floor level from the ground. Add 1.5% extra over the rate for each additional floor or 4m. beyond initiial 8m. or part thereof. III) For built up sections / srtuctural members of specified sections weighing not less than 22.5 Kg./m |
| 27 | BUILDING WORKS ( C ) Brickworks,Concrete Works etc A. BRICK WORKS 8. Brick work with 1st class bricks in cement mortar (1:6) (b) In superstructure, ground floor |
| 28 | SUPPLY & DELIVERY AT SITE OF PRESSURE GAUGE HAVING DIAL SIZE 150MM. RANGE OF PRESSURE 0 TO 7 KG/CM2 AND 0 TO 1 KG/CM2 MODEL 1PSSSWA2 AND MADE OF DIE CAST ALUMINIUM. WEATHERPROOF. PAINTED STOVE ENAMELED BLACK FINISH SCREW INNER BEZEL OF ABS PLASTIC. RATE ANALYSIS APPROVED BY DG(WS) ON DATED 21/08/2020. |
| 29 | PLUMBING WORKS (A)-(II) G.I. PIPE WORKS AND FITTINGS 5. Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only). (ix) 15 mm dia |
| 30 | MATERIALS AND LABOUR ETC.(C)-(II) COST OF MATERIALS 1.Supply of G. I. pipes of TATA make including necessary sockets (a) 15 mm dia. (ii) Medium quality |
| 31 | Sub Total |
| 32 | GST 18% |
| 33 | CESS 1% Please Enable Macros to View BoQ information |
