|
| 1 | • bipolar radiofrequency generator console should perform plasma excision, pure coagulation, homeostasis & simultaneous soft tissue resection and ablation properties.• it should generate a fixed amount of power that should not fluctuate based on the operating environment • should be capable of probe recognition and automatic adjustment of power settings• should accommodate both suction and non-suction probes• should have scope protection with impedance monitoring technology• bipolar multi electrode ablation system, hand/ foot-controlled ablation probes should allow operating cut and coagulation as well as changing the power setting on the system.• footswitch activation - should be supplied with foot switch• compatible rf probes for ablation, coagulation, and haemostasis in arthroscopic surgery.• radiofrequency energy probes: probes should be designed with a rigid shaft in order to prevent unwanted bending during use, the suction probes should support a suction rate of at least150ml/min each probe should be designed with integrated cable allowing for easy case preparation and clean up. |
| 2 | Arthroscopy Radiofrequency Ablation (RF) System- Footswitch |
| 3 | Radio frequency energy probes for Menisectomy - 90 degree For Knee Arthroscopy |
| 4 | Radio frequency energy probes for Posterior Menisectomy-50degree For Knee Arthroscopy |
| 5 | Radio frequency energy probes for Articular Cartilage debridement-ablation For Knee Arthroscopy |
| 6 | Radio frequency energy probes for Soft tissue debridement-ablation For Knee Arthroscopy |
| 7 | Radio frequency energy probes for Sub acromial decompression 90 degree ablation for shoulder arthroscopy |
| 8 | Radio frequency energy probes for Capsular release ablation for shoulder arthrscope |
| 9 | Shaver Console • Console-driven shaver system with high-torque and variable-speed motor.• Control: Console panel and footswitch (dual pedal).• Console screen should capture all information pertaining to minimum, maximum and set speeds for installed blade type, blade direction, and diagnostic information• Speed: 0 – 3000 RPM oscillating modes. Should provide variable RPM from 0 - 7000rpm depending on blades or burrs used.• It should be supplied with single-use blades and burrs for different joint surgeries• The motor should offer Forward, Reverse and Oscillation Mode for Resection. |
| 10 | Foot Pedal For above shaver system (same manufacturer as above)• The variable speed foot pedal should be sturdy with a long connecting cable.• The foot pedal controls should include three standard operating modes, i.e. Forward, Reverse and Oscillation |
| 11 | Shaver Handpiece for shaver system above of same manufacturer• Lightweight, autoclavable, ergonomic design, with optional hand control.• The connecting cable should be autoclavable and replaceable with length of approx. 10 feet• The hand piece should have suction control lever.• The shaver hand piece should have push-button motor controls Forward, Reverse, Oscillate and Blade.• The shaver should be supplied with sterilization case. |
| 12 | Aggressive Plus Cutter -4 mm for Resection Shaver System- Box of 5 |
| 13 | Resector Cutter -4 mm for Resection Shaver System - Box of 5 |
| 14 | Tomcat cutter- 4 mm for Resection Shaver System - Box of 5 |
| 15 | Agressive Plus Angled blade 4 mm for Resection Shaver System Box of 5 |
| 16 | Aggressive blade-2.5 mm for Resection Shaver System -Box of 5 |
| 17 | Subcondral drill Resection Shaver System -Box of 5 |
| 18 | Hooded Abrasion Bur for Resection Shaver System-Box of 5 |
| 19 | Medical grade trolley:- With minimum 5 raqckets to keep consoles, should have common electric supply & different connection to attach each console, should have wheel & carry minimum 50 kg for all console & equipments and must Complies with medical safety standards and US FDA Approved |
| 20 | The 4K Arthroscopes should have following features:• The arthroscope should be provisioned with compatible sheath/cannula with inflow and outflow with stop-lock and attachment portal for light source and camera• High transmission optics with scratch-resistant sapphire distal window.• Standard ocular window for coupling the camera head.• Advanced rod lens system for optimum brightness, contrast and definition• Optimal centre to edge resolution for enhanced picture quality• Compatibility with standard arthroscopy sheaths and trocars. |
| 21 | 4K ARTHROSCOPE 4 mm-4.5 mm X 30 DEG with Direct View Autoclavable Arthroscope, Field of view: of 105 deg or more, Angle of view: 30 deg, Working length: 150mm, for knee and 175 mm with sheath & obturator for knee and shoulder surgery |
| 22 | 4K ARTHROSCOPE 4 mm-4.5 mm X 70 DEG with Direct View Autoclavable Arthroscope, Field of view: of 105 deg or more, Angle of view: 30 deg, Working length: 150mm, for knee and 175 mm with sheath & obturator for knee and shoulder surgery |
| 23 | • 4.0 - 4.5 mm 4K/HD diameter, 30°, working length 175 mm with Sheath & Obturator for Hip Surgeries |
| 24 | 4.0 - 4.5 mm 4K/HD diameter, 70°, working length 175 mm with Sheath & Obturator Hip Surgeries |
| 25 | 2.7 – 3 mm, 30°, 4K/HD working length up to 120- 155 mm with Sheath & Obturator for ankle, elbow surgeries |
| 26 | 2.2 - 2.7 mm,4K/HD 30°, working length 65-90 mm with Sheath & Obturator for wrist surgeries |
| 27 | 1.9 mm, 30°,4K/HD working length 65 - 90 mm, with Sheath & Obturator for wrist surgeries |
| 28 | Advanced Visualization (4K Resolution) System for Arthroscopic Knee, Hip, Shoulder, Wrist, Elbow, and Ankle Surgeries.• The system shall be a complete, integrated 4K Ultra High Definition 3-CMOS Arthroscopy System suitable for advanced arthroscopic procedures of the hip, knee, shoulder, elbow, and wrist.• All components should be integrated and compatible within a single manufacturer’s ecosystem for seamless use.• All scopes, cables, and hand instruments should be autoclavable.• The system should have a facility for remote software diagnostics and updates.• The offered/quoted Model should not be obsolete or one that is being phased out.• The complete system should be USFDA / BIS / European CE/ CDSCO Approved.• The system should have an Import license (Form MD-15) for foreign manufacturers and (Form MD-9/MD-10) for Indian manufacturers. The system shall consist of the following components, complying with the technical specifications provided for each: |
| 29 | 4K 3-CMOS Camera System with Camera Control Unit (CCU) • Imaging & Sensor technology: The camera system shall be a true 4K Ultra HD resolution camera chain (3840 × 2160 pixels), equipped with a 3-CMOS or advanced CMOS (3-chip) sensor technology capable of true 4K Ultra HD resolution (3840 × 2160 pixels or higher) to ensure superior colour reproduction, contrast, and low-light performance. 3-CMOS systems split light into red, green, and blue channels, each captured by an independent sensor, producing superior colour fidelity and clarity.• 4K @ 50 fps progressive scan output: The 4K 3-CMOS camera system shall provide progressive scan imaging at ≥60 frames per second (fps) at full 4K UHD resolution, (for smooth, lag-free motion), with automatic and manual white balance and gain control.• The 4K camera system shall have advanced image processing with wide dynamic range (HDR or equivalent technology) to enhance visualization in both bright and dark regions simultaneously.• High signal-to-noise ratio (SNR): The 4K 3-CMOS camera system shall provide a high signal-to-noise ratio (≥64 dB or equivalent) with optimized colour reproduction, depth perception, and low-light performance.• CCU shall have multiple video outputs: HDMI, 3G-SDI/12G-SDI, DVI, DisplayPort.• Integrated image enhancement features: digital zoom, noise reduction.• Shall be compatible with Hosp Picture Archiving & Communication Systems (PACS).• Compact design with a user-friendly interface and touch control preferred. |
| 30 | 4K 3-CMOS Camera Head – • The camera head can be steam and chemical sterilized and should have 2 or more buttons which can control at-least 6 functions• The camera should have Coupler of size 17.2 to 24 mm.• Camera Head Cable: 9 to 10 ft sealed cable• White balance can be done from the camera head as well as from the console. |
| 31 | HD recording solution –• The endo-vision system should have an inbuilt within the camera or separate console, IMS (recorder). It should be medical grade The image management system (recorder) can record the images, videos The camera head should have button controls to click images and record videos. The recorder should have the ability to transfer captured still and video images to external media using USB interface on front panel. External Storage (recording space) should be at least 128 GB • USB slot for recording via a Pen drive. |
| 32 | 4K Ultra High-Definition Medical Grade Monitor – • Size: 27-32 inches, medical-grade LED/LCD monitor.• Resolution:4K UHD (3840× 2160) with high brightness and contrast ratio (≥1000:1).• Wide viewing angle ≥178°.• image processing for real-time visualization.• Anti-reflective, waterproof, and easily cleanable front panel suitable . • Multiple input compatibility (HDMI, 3G/12G-SDI, DisplayPort, DVI).• Articulating, Compact & lightweight design |
| 33 | LED Light Source (Integrated or separate console) • High-intensity LED light source, with ≥2000 lumens (preferably 3000 lumens).• Colour temperature: Adjustable colour temperature in the range of 4000–6000 K (daylight equivalent) for optimal tissue visualization.• LED lamp life: ≥20,000 hours (preferably 25,000 hours or more)• Low heat generation and quiet cooling system.• Compatible fibre optic light cable with universal connector, length ≥3 meters.• Light guide cables with size 4mm*8 feet. should be 2 qty• The light source should have a Universal Jaw Assembly to adapt Fiber Optic Cable of any make.• Light source should have Standby Illumination option – should haven Standby Illumination button to put light source in standby mode and the light source is off when not in use. |
| 34 | Arthroscopy Fluid Management System (inflow outflow Pump) • Peristaltic pump-based system with dual pump technology (inflow & outflow). Must support both gravity-fed and pressure pump modes.• Adjustable pressure range should be 0–150 mmHg (or higher). The fluid management system should be capable of controlling and maintaining intra-articular pressure regardless of varying outflow rates• High flow rate of up to 1.5- 2 litres per minute for procedural speed and efficiency.• Automatic pressure control with real-time feedback for joint distension. It should allow automatic joint pressure maintenance up to 150 mm Hg.• Touchscreen interface Display should have Digital screen with pressure and flow indicators. |
| 35 | Disposable Tube sets for inflow and outflow should be supplied with disposable Tube sets for inflow and outflow and compatible with standard arthroscopic cannulas and tubing sets for above arthropump |
| 36 | Limb Positioner• It should have secure and adjustable positioning for optimal access• The components should have complete assembly included for shoulder positioning (Lateral Decubitus Position (Qty 01)• Beach chair positioner (Qty 01)• Should be fixed with side rails of any operating tables.• Should have 360 deg range of motion for the joints.• Should be made of Aluminium and carbon fibre to make it light and portable.• The weight should not be more than 7Kg.• The mount accessories should be autoclavable. |
| 37 | Arthroscope Sheath with rotating two stopcocks- 5.8mm |
| 38 | Pencil Obturator to fit above Sheath |
| 39 | Blunt Obturator to fit above Sheath |
| 40 | Small Joint Straight Blunt Nose -2.1 mm |
| 41 | Small Joint Right Blunt Nose -2.1 mm |
| 42 | Small Joint Left Blunt Nose -2.1 mm |
| 43 | Small Joint Down Blunt Nose -2.1 mm |
| 44 | Small Joint Up Blunt Nose -2.1 mm |
| 45 | Small Joint Scissors -2.5 mm |
| 46 | Small Joint Grasper -2.5 mm |
| 47 | Small Joint Straight Blunt Nose -2.7 mm |
| 48 | Small Joint Up Blunt Nose -2.7 mm |
| 49 | Small Joint Probe straight |
| 50 | Small joint Probe 90 degree |
| 51 | Small joint probe 30 degree |
| 52 | Mini small joint punch-2.0mm |
| 53 | Small joint grasper-2.0mm |
| 54 | Small joint Scissors-2.0mm |
| 55 | Sterilization tray for small joint Hand instruments |
| 56 | Water snake floor sunction device for Arthroscopy Pump US FDA certified. -(Box of 10) |
| 57 | Arthroscopic ACL/PCL/Graft master instrument set |
| 58 | Tibial drill guide spine for arthroscopy |
| 59 | Tibial drill guide single point forked arm for arthroscopy |
| 60 | Tibila drill guide double point forked arm for arthroscopy |
| 61 | Tibil drill guide elbow arm for arthroscopy |
| 62 | Tibial drill guide bolt with calibrations for arthroscopy |
| 63 | Tunnel notcher for arthroscopy |
| 64 | Arthroscopic probe 5 mm |
| 65 | Tendon stripper-blunt tip, for open and closed tendon stripper |
| 66 | Femoral aimers with non-detachable handle- sizes of 4 mm |
| 67 | Femoral aimers with non-detachable handle- sizes of 5 mm |
| 68 | Femoral aimers with non-detachable handle- sizes of 6 mm |
| 69 | Femoral aimers with non-detachable handle- sizes of 7 mm |
| 70 | Femoral aimers with non-detachable handle- sizes of 8 mm |
| 71 | Femoral reamers-calibrated reamers with tri-flute design, should be calibrated at every 5 mm for accurate femoral tunnel drilling, size 5 mm |
| 72 | Femoral reamers-calibrated reamers with tri-flute design, should be calibrated at every 5 mm for accurate femoral tunnel drilling, size 5 .5 mm |
| 73 | Femoral reamers-calibrated reamers with tri-flute design, should be calibrated at every 5 mm for accurate femoral tunnel drilling, size 6 mm |
| 74 | Femoral reamers-calibrated reamers with tri-flute design, should be calibrated at every 5 mm for accurate femoral tunnel drilling, size 6.5 mm |
| 75 | Femoral reamers-calibrated reamers with tri-flute design, should be calibrated at every 5 mm for accurate femoral tunnel drilling, size 7 mm |
| 76 | Femoral reamers-calibrated reamers with tri-flute design, should be calibrated at every 5 mm for accurate femoral tunnel drilling, size 7.5 mm |
| 77 | Femoral reamers-calibrated reamers with tri-flute design, should be calibrated at every 5 mm for accurate femoral tunnel drilling, size 8 mm |
| 78 | Femoral reamers-calibrated reamers with tri-flute design, should be calibrated at every 5 mm for accurate femoral tunnel drilling, size 8.5 mm |
| 79 | Femoral reamers-calibrated reamers with tri-flute design, should be calibrated at every 5 mm for accurate femoral tunnel drilling, size 9 mm |
| 80 | Femoral reamers-calibrated reamers with tri-flute design, should be calibrated at every 5 mm for accurate femoral tunnel drilling, size 9.5 mm |
| 81 | Femoral reamers-calibrated reamers with tri-flute design, should be calibrated at every 5 mm for accurate femoral tunnel drilling, size 10 mm |
| 82 | Femoral reamers-calibrated reamers with tri-flute design, should be calibrated at every 5 mm for accurate femoral tunnel drilling, size 10.5 mm |
| 83 | Femoral reamers-calibrated reamers with tri-flute design, should be calibrated at every 5 mm for accurate femoral tunnel drilling, size 11 mm |
| 84 | Femoral reamers-calibrated reamers with tri-flute design, should be calibrated at every 5 mm for accurate femoral tunnel drilling, size 11.5 mm |
| 85 | Femoral reamers-calibrated reamers with tri-flute design, should be calibrated at every 5 mm for accurate femoral tunnel drilling, size 12 mm |
| 86 | Tibial reamers- for reaming the tibial tunnel, size 6 mm |
| 87 | Tibial reamers- for reaming the tibial tunnel, size 6.5 mm |
| 88 | Tibial reamers- for reaming the tibial tunnel, size 7 mm |
| 89 | Tibial reamers- for reaming the tibial tunnel, size 7.5 mm |
| 90 | Tibial reamers- for reaming the tibial tunnel, size 8 mm |
| 91 | Tibial reamers- for reaming the tibial tunnel, size 8.5 mm |
| 92 | Tibial reamers- for reaming the tibial tunnel, size 9 mm |
| 93 | Tibial reamers- for reaming the tibial tunnel, size 9.5 mm |
| 94 | Tibial reamers- for reaming the tibial tunnel, size 10 mm |
| 95 | Graft sizing block |
| 96 | Instrumentation tray for Arthroscopic ACL/PCL/Graftmaster instrument set |
| 97 | Versitomic cannulated drill 4.5 mm |
| 98 | Tunnel Notcher |
| 99 | Tibial plug |
| 100 | Graft Preparation system for preparing soft tissue and Bone-tendon-bone grafts with Base for ACL work station-1, |
| 101 | Muscle removal board-1 |
| 102 | Slider-2 |
| 103 | Stationary board-1 |
| 104 | Stationary clamp-2 |
| 105 | Stationary tensioner-1 |
| 106 | Instrumentation tray for graft preparation instruments |
| 107 | Guide wire 1.5 mm X14 inch -Box of 6 |
| 108 | Femoral eyeloop guide pin-drill tip 2.4 mm X 12”-Box of 6 |
| 109 | Tibial guide pin 2.4 mm X 9\\" -Box of 6 |
| 110 | Director PCL Tibial Aimer with broad face tip that easily passes through notch & provides protection to posterior capsule during guide wire drilling. |
| 111 | Director PCL Femoral Aimer for outside in Drilling with medial incision, should have hoop tip to provide visual reference for the diameter of the fully reamed tunnel. |
| 112 | Director 4- Point Bullet with four sharp points for secure engagement to the guide at any angle |
| 113 | PCL instruments-should be compatible with ACL zig to enable PCL reconstruction. |
| 114 | PCL femoral arm compatible with ACL zig to enable PCL reconstruction.- |
| 115 | PCL tibial arm compatible with ACL zig to enable PCL reconstruction |
| 116 | PCL backstopper compatible with ACL zig to enable PCL reconstruction |
| 117 | PCl curette compatible with ACL zig to enable PCL reconstruction |
| 118 | PCL liberator/rasp compatible with ACL zig to enable PCL reconstruction |
| 119 | Flexible Reamer for ACL reconstruction with Anatomic portal placement – 4.5 mm |
| 120 | Flexible Reamer for ACL reconstruction with Anatomic portal placement – 5 mm |
| 121 | Flexible Reamer for ACL reconstruction with Anatomic portal placement – 5.5 mm |
| 122 | Flexible Reamer for ACL reconstruction with Anatomic portal placement – 6 mm |
| 123 | Flexible Reamer for ACL reconstruction with Anatomic portal placement – 6.5 mm |
| 124 | Flexible Reamer for ACL reconstruction with Anatomic portal placement – 7 mm |
| 125 | Flexible Reamer for ACL reconstruction with Anatomic portal placement – 7.5 mm |
| 126 | Flexible Reamer for ACL reconstruction with Anatomic portal placement – 8 mm |
| 127 | Flexible Reamer for ACL reconstruction with Anatomic portal placement – 8.5 mm |
| 128 | Flexible Reamer for ACL reconstruction with Anatomic portal placement – 9 mm |
| 129 | Flexible Reamer for ACL reconstruction with Anatomic portal placement – 9.5 mm |
| 130 | Flexible Reamer for ACL reconstruction with Anatomic portal placement – 10 mm |
| 131 | Flexible Reamer for ACL reconstruction with Anatomic portal placement – 10.5 mm |
| 132 | Flexible Reamer for ACL reconstruction with Anatomic portal placement – 11 mm |
| 133 | Flexible Reamer for ACL reconstruction with Anatomic portal placement – 11.5 mm |
| 134 | Flexible Reamer for ACL reconstruction with Anatomic portal placement – 12 mm |
| 135 | Disposable Flexible Pin with eyeloop and trocar tip made up of Shape Memory Alloy- (Box of 5) |
| 136 | Disposable flexible pin with marking to enable measurement of portal with outside in depth gauge - (Box of 5) |
| 137 | Outside-in depth guage with sharp tip to enable total portal length |
| 138 | Awl to make a starting point and ensure exit of flexible guide pin |
| 139 | Forked Aimer with a slot specifically designed to grab, bend, place and manipulate the flexible Guide Pin with ease while inside the joint. |
| 140 | Anteriomedial Portal offset guide to be used through the anteriomedial portal to achieve longer femoral tunnels without the need to hyperflex the knee with a built in pin predictor with the flip of the pin |
| 141 | Anteriomedial Portal offset guide 5 mm right |
| 142 | Anteriomedial Portal offset guide 6 mm left |
| 143 | Anteriomedial Portal offset guide 6 mm right |
| 144 | Anteriomedial Portal offset guide 7 mm left |
| 145 | Anteriomedial Portal offset guide 7 mm right |
| 146 | Anteriomedial Portal straight for placement on footprint - common for left and right knee |
| 147 | Anteriomedial Portal guides with 45 degree curvature |
| 148 | Osteochondral drilling system set :- Should be autoclavable, should be used in Knee, Shoulder & hip in femoryal condyle, Actabulam, & underside of patella. , should have long & small sleaves for knee, Shoulder & hip, should be in 45 deg available |
| 149 | Osteochondral drilling system set :- Should be autoclavable, should be used in Knee, Shoulder & hip in femoryal condyle, Actabulam, & underside of patella. , should have long & small sleaves for knee, Shoulder & hip, should be in 70 deg available |
| 150 | Osteochondral drilling system set :- Should be autoclavable, should be used in Knee, Shoulder & hip in femoryal condyle, Actabulam, & underside of patella. , should have long & small sleaves for knee, Shoulder & hip, should be in 90 deg available |
| 151 | Angled ring curette |
| 152 | Angled reversed triangle curette for above Osteochondral drilling system |
| 153 | Angled pear curette for above Osteochondral drilling system |
| 154 | Long Angled Ring curette for above Osteochondral drilling system |
| 155 | Long Angled reverse Triangle curette for above Osteochondral drilling system |
| 156 | Long angled pear curette. for above Osteochondral drilling system |
| 157 | Osteochondral Guide- 0° |
| 158 | Osteochondral Guide - 45° |
| 159 | Osteochondral Guide -70° |
| 160 | Osteochondral Guide - 90° |
| 161 | Osteochondral Guide, Long -45° |
| 162 | Osteochondral Guide, Long -70° |
| 163 | Osteochondral Guide, Long - 90° |
| 164 | Osteochondral Snap Cap- 4 mm |
| 165 | Osteochondral Snap Cap- 5 mm |
| 166 | Osteochondral Snap Cap- 6 mm |
| 167 | Osteochondral Snap Cap- 7 mm |
| 168 | Angled Ring Curette |
| 169 | Angled Reverse Triangle Curette |
| 170 | Angled Pear Curette |
| 171 | Long Angled Ring Curette |
| 172 | Long Angled Reverse Triangle Curette |
| 173 | Long Angled Pear Curette |
| 174 | Osteochondral Universal Drill ( box of 5) |
| 175 | Autoclavable instrument tray for above system |
| 176 | Switching stick 4 mm for portal placements for shoulder arthroscope |
| 177 | Switching stick 5 mm for portal placements for shoulder arthroscope |
| 178 | Reusable cannula obturators of diameter 6.5 mm with a length of 75 mm for shoulder arthroscope |
| 179 | Reusable cannula obturators of diameter 8 mm with a length of 75 mm for shoulder arthroscope |
| 180 | Probe 3 mm for shoulder arthroscope |
| 181 | Tissue liberators for preparation of bone and tissue: Blade up |
| 182 | Tissue liberators for preparation of bone and tissue: Blade down |
| 183 | Rasp to create bleeding on glenoid to prepare for labrum reattachment site- 20 degree up bend |
| 184 | Rasp to create bleeding on glenoid to prepare for labrum reattachment site- 20 degree down bend |
| 185 | Tissue Grasper with rachet for shoulder arthroscope |
| 186 | Suture manipulator for manipulating the suture for shoulder arthroscope |
| 187 | Crochet hook for shoulder arthroscope |
| 188 | Knot pusher for shoulder arthroscope |
| 189 | Suture Grasper with Rachet for shoulder arthroscope |
| 190 | 2mm suture cutter with transverse loading technique |
| 191 | Tray for sterilization and storage of above instruments |
| 192 | Penetrating Graspers for Suture passage and retrieval for bankart and slap repair - left |
| 193 | Penetrating Graspers for Suture passage and retrieval for bankart and slap repair - right |
| 194 | Penetrating Graspers for Suture passage and retrieval for bankart and slap repair - 45 degree up |
| 195 | Penetrating Graspers for Suture passage and retrieval for bankart and slap repair - 30 degree up |
| 196 | Penetrating Graspers for Suture passage and retrieval for bankart and slap repair - straight |
| 197 | Stability hooks - specifically designed for suture passing and retrieving at the 6 o’clock position of the glenoid labrum Using a twist-in, twist-out motion, the StabiliHook is designed for instability repair twist in and twist out motion. - Left |
| 198 | Stability hooks - specifically designed for suture passing and retrieving at the 6 o’clock position of the glenoid labrum Using a twist-in, twist-out motion, the StabiliHook is designed for instability repair twist in and twist out motion. - Right |
| 199 | Cuff hook – specifically designed for suture passing and retrieving during cuff repair - Left |
| 200 | Cuff hook – specifically designed for suture passing and retrieving during cuff repair - Right |
| 201 | HIP ARTHROSCOPY Instrument set :- Autoclavable and should be made up of Stainless still with ergonomic handle and should have very minute precision , Should have direct view, with 4.0 mm – 30 degree with wide angle and speed lock mechanism, |
| 202 | HIP ARTHROSCOPY Instrument set :- Autoclavable and should be made up of Stainless still with ergonomic handle and should have very minute precision , Should have direct view, with 4.0 mm – 70 degree with wide angle and speed lock mechanism, |
| 203 | 5.8 mm operative cannula with trocar for hip arthroscopy |
| 204 | 5.8 mm Compatible cannulated obturator for hip arthroscopy |
| 205 | Cannula, trocar and obturator with working length 140 cm and 300 cm, diameter 4 mm for hip arthroscopy |
| 206 | Cannula, trocar and obturator with working length 140 cm and 300 cm, diameter 5.5 mm for hip arthroscopy |
| 207 | Cannula, trocar and obturator with working length 140 cm and 300 cm, diameter 6.5 mm for hip arthroscopy |
| 208 | Hip bridge for hip arthroscopy |
| 209 | Cannulated switching stick compatible with cannulas – 4 mm for hip arthroscopy |
| 210 | Cannulated switching stick compatible with cannulas – 5 mm for hip arthroscopy |
| 211 | Graspers 4 mm straight and 15 degree up |
| 212 | Graspers Size 4 mm, straight |
| 213 | Graspers Size 4 mm, left |
| 214 | Graspers Size 4 mm, right |
| 215 | Suture Manipulation-1 each |
| 216 | 4 mm suture passer and retriever right |
| 217 | 4 mm suture passer and retriever left |
| 218 | 4 mm suture passer and retriever 15 degree up |
| 219 | 4 mm suture passer and retriever 35 degree up |
| 220 | 4 mm suture grasper |
| 221 | 5 mm suture cutter |
| 222 | 3 mm knot pusher |
| 223 | Probes-3mm 90 degree straight |
| 224 | Probes-3mm 90 degree curved |
| 225 | Microfracture- Microfracture pick 2.3mm straight |
| 226 | Rigid Instruments-4 mm hip curette |
| 227 | 4 mm hip rasp |
| 228 | 4 mm hip liberator |
| 229 | Accessories-Hip Needle |
| 230 | Hip Long Knife Handle |
| 231 | Nitinol guide wires |
| 232 | Sealing cap |
| 233 | Hip Autoclavable Instrument tray |
| 234 | Suture Passer -Ratchet Straight Capture |
| 235 | Suture Passer -Ratchet Straight Capture 16 mm bite which allows for optimal management of the rotator cuff tissue. |
| 236 | Suture Passer -Ratchet Straight Capture low-profile, 4.6 mm wide jaw with small upper \\"teeth\\", for a secure grasp of the tissue to enable accuracy and precision when passing suture. |
| 237 | Suture Passer -Ratchet Straight Capture 10 mm open jaw height: 6.1 mm closed height. |
| 238 | Suture Passer -Ratchet Straight Capture automatic suture-capture retrieving jaw. |
| 239 | Suture Passer -Ratchet Straight Capture straight, low-profile upper jaw. |
| 240 | Suture Passer -Ratchet Straight Capture compatible with a 6.5 mm Cannula. |
| 241 | Passer Needle(Disposable)- (Box of 5) for Suture Passer -Ratchet Straight Capture |
| 242 | Suture passing needle and nitinol shuttles :- Suture slider to pass nitinol shuttle for suture passing-should include autoclavable handle |
| 243 | Suture passing needle |
| 244 | Suture passing needle 25 degrees left |
| 245 | Suture passing needle 25 degrees right |
| 246 | Suture passing needle 45 degrees left |
| 247 | Suture passing needle 45 degrees right |
| 248 | Suture passing needle Straight 60 degree |
| 249 | Slider nitinol shuttle - (Box of 5) |
| 250 | 3.4 mm Backbiter punch |
| 251 | 3.4 mm Straight Big Bite Punch |
| 252 | 2.7 mm Straight Big Bite Punch |
| 253 | 3.4 mm 30 Right Big Bite Punch |
| 254 | 2.7 mm 30 Right Big Bite Punch |
| 255 | 3.4 mm 30 Left Big Bite Punch |
| 256 | 3.4 mm 15 up Big Bite Punch |
| 257 | 2.7 mm 15 up Big Bite Punch |
| 258 | 3.4 mm Upshaft Big Bite Punch |
| 259 | 2.7 mm Upshaft Big Bite Punch |
| 260 | 3.4 mm 45 Left Tip Biter |
| 261 | 2.7 mm 45 Right Tip Biter |
| 262 | 3.4 mm Straight Scoop Jaw Punch |
| 263 | 3.4 mm 30 Right Scoop Jaw Punch |
| 264 | 3.4 mm 30 left Scoop Jaw Punch |
| 265 | 3.4 mm Narrow Punch |
| 266 | 2.7 mm Narrow Punch |
| 267 | 3.4 mm 15 Up Narrow Punch |
| 268 | 3.4 mm Right Meniscal Crescent Punch |
| 269 | 3.4 mm Left Meniscal Crescent Punch |
| 270 | 3.4 mm 30 Left Meniscal Crescent Punch |
| 271 | 3.4 mm 30 Right Meniscal Crescent Punch |
| 272 | 3.4 mm 90 Right Rotary Punch |
| 273 | 3.4 mm 90 Left Rotary Punch |
| 274 | 3.4 mm Hook Scissors |
| 275 | 3.4 mm 30 Left Hook Scissors |
| 276 | 3.4 mm 30 Right Hook Scissors |
| 277 | 3.4 mm Micro Scissors Punch |
| 278 | 2.7 mm Micro Scissors Punch |
| 279 | 4 mm Soft Tissue Grasper |
| 280 | 3.4 mm Soft Tissue Grasper |
| 281 | 2.7 mm Soft Tissue Grasper |
| 282 | 3.4 mm Soft Tissue Grasper with Ratchet |
| 283 | 2.7 mm Soft Tissue Grasper with Ratchet |
| 284 | 3.4 Grasper |
| 285 | 3.4 mm Grasper with Ratchet |
| 286 | Sterilization Box with Tray for long instruments 24 x 12 inch made up from Medical grade anodized alluminium |
| 287 | Wrist ARTHROSCOPY Instrument set :- Autoclavable and should be made up of Stainless still with ergonomic handle and should have very minute precision , Should have direct view, with 2.7 mm – 30 degree with wide angle and speed lock mechanism, |
| 288 | Arthroscopic Transosseous Tunnel device system for Arthroscopic transosseous rotator cuff repair |
| 289 | Ti Button with Adjustable Fiber Loop, with Flipping & Pulling suture - Sterile |
| 290 | Ti Button with Adjustable Fiber Loop with Fiber Tape Size 2 for Augmentation with Flipping & Pulling suture - Sterile |
| 291 | Adjustable Fiber Loop without button for attachable button- Sterile |
| 292 | Ti Button with Adjustable Fiber Loop kit for BPTB ACL reconstruction - Sterile |
| 293 | Biocomposite Absorbable Interference screw (75percentage PLDLLA & 25percentage BCP) assorted size (Dia 7mm to 11mm) -Sterile |
| 294 | PEEK Interference Screw With Perforation Holes, assorted size (Dia 6mm to 11mm) -Sterile |
| 295 | Titanium Interference Screw With soft thread, assorted size (Dia 7mm to 10mm) -Sterile |
| 296 | Tibial Base Plate tapered with serration, Attachable Button titanium , 4 holes(Small & large size) -Sterile |
| 297 | Tibial Base Plate, Attachable Button PEEK , 4 holes (standard size ) -Sterile |
| 298 | Attachable Button round tapered with 4 holes, , dia 10mm Titanium -Sterile |
| 299 | Attachable Button round tapered with 4 holes ,round, dia 10mm PEEK -Sterile |
| 300 | Fiber wire size 2 with curved needle suture length 38\\", (Colour : White, White-Blue, White-Black) - Sterile |
| 301 | Fiber Wire size 5 with curved needle suture length 38\\", (Colour : White, White-Blue, White-Black) - Sterile |
| 302 | Fiber Wire size 2-0 with reverse curved needle suture length 38\\", (Colour :White-Blue) - Sterile |
| 303 | Fiber Wire Loop, size 2 with the straight needle len 6 cm, White -Blue Len 24\\" (Graft stitching) - Sterile |
| 304 | Fiber Tape Size 2 , Length 38\\", with both end round,Tape working length 15\\" (Colour : White-Blue, White-Black) - Sterile |
| 305 | Fiber Tape Size 1.4 , Length 38\\", with both end round, Tape working length 30\\" (Colour : White-Blue, White-Black) - Sterile |
| 306 | Fiber Tape Size 1.1 , Length 38\\", with both end round, Tape working length 30\\" (Colour : White-Blue, Blue-Black) - Sterile |
| 307 | All Inside Meniscal Repair Kit, 2 PEEK implant with Fiber wire 2-0, 360 degree deploy mechanism , needle dia should not more than dia 1.5 (Type : Straight, Curved, Reverse Curved ) -sterile |
| 308 | All Inside Meniscal repair kit with 2 PEEK implant with Fiber Tape size 0.7mm , 360 degree deploy mechanism ,needle dia should not more than dia 1.5 (Type : Straight,Curved,Reverse Curved ) -sterile |
| 309 | Inside-Out Meniscal repair set with flexible needles Fiber USP Size 2-0/ USP size 0, suture Len. 75cm, straight needles-2 units, needle Len. 25cm - sterile |
| 310 | Inside-Out Meniscal repair set with flexible needles Fiber Tape size 0.7, Tape Len. 50cm, straight needles-2 units, needle Len. 25cm - Sterile |
| 311 | MPFL Repair Kit - SterileComprises of - PEEK Suture Anchor, Knotless, dia. 3.5mm, closed eyelet with Screw (Total Length 19mm), loaded on disposable driver (Qty 2 Pcs),PEEK Interference Screw With Perforation Holes, dia 6mm, len 23mm (Qty 1 pcs),Fiber Tape Size 2 , Len 19\\", with flat end (Qty 1 pcs), |
| 312 | Titanium Suture Anchor, dia. 5.0mm, with Double-Loaded/Triple-Loaded Fiber Wire, (USP Size 2) (different colors), loaded on disposable driver – Sterile |
| 313 | Titanium Suture Anchor, dia. 5.0mm, with Double-Loaded/Triple-Loaded Fiber Wire, (USP Size 2)(different colors), with needle, loaded on disposable driver – Sterile |
| 314 | Titanium Suture Anchor, dia. 6.5mm, double-loaded Fiber Wire, (USP Size 2)(different colors) for Osteoporotic bone, loaded on disposable driver – Sterile |
| 315 | PEEK Suture Anchor, dia. 4.5 mm/ 5.5mm, with Double-Loaded/Triple-Loaded Fiber Wire (USP Size 2)(different colors), loaded on disposable driver – Sterile |
| 316 | PEEK Suture Anchor, dia. 4.5 mm/ 5.5mm, loaded with one Fiber Wire (USP Size 2) and one Fiber Tape Size 1.4mm, loaded on a disposable driver – Sterile |
| 317 | PEEK Suture Anchor, Knotless, dia. 4.75mm/ 5.5mm, for lateral row / double row repair, loaded on disposable driver – Sterile |
| 318 | PEEK Suture Anchor, Knotless, dia. 3.5mm, for lateral row repair, closed eyelet with Screw (Total Length 19mm), loaded on disposable driver – Sterile |
| 319 | Self-Punching Suture Anchor, Knotless, dia. 4.75mm/ 5.5mm, for lateral row / double row repair, with Ti eyelet option & PEEK screw, loaded on disposable driver – Sterile |
| 320 | All-Suture Anchor /Soft Anchor, dia. 2.9mm, Double-Loaded/Triple-Loaded with Fiber Wire (USP Size 2)(different colors), loaded on a self-punching rigid disposable driver – Sterile |
| 321 | All-Suture Anchor/ Soft anchor, dia. 2.9mm, loaded with one Fiber Wire (USP Size 2) and Fiber Tape size 1.4mm,loaded on a rigid self-punching disposable driver – Sterile |
| 322 | All-Suture Anchor/ Soft anchor, dia. 2.9mm, One sliding Fiber Wire (USP Size 2)and one Fix Fiber tape size 1.4mm with , loaded on the self punching rigid disposable driver for medial row repair, |
| 323 | All-Suture Anchor/ Soft anchor, dia. 2.9mm, loaded with Two Fiber Tape size 1.4mm, loaded on a rigid self-punching disposable driver – Sterile |
| 324 | All-Suture Anchor/ Soft anchor, dia. 2.9mm, loaded with Two Fiber Tape size 1.4mm with needle, loaded on a rigid self-punching disposable driver – Sterile |
| 325 | All-Suture Anchor/ Soft anchor, dia. 2.9mm, Knotless, Double-Loaded, loaded on a self-punching rigid disposable driver for Medial row repair– Sterile |
| 326 | Biocomposite Absorbable Suture Anchor, dia. 4.5mm/5.5 mm, double-loaded with Fiber Wire, (USP Size 2)(different colors), loaded on disposable driver – Sterile |
| 327 | Biocomposite Absorbable Suture Anchor, Knotless, dia. 4.75mm/5.5 mm, for Lateral Row / Double Row repair, PEEK eyelet, loaded on a disposable driver – Sterile |
| 328 | Biocomposite Absorbable Suture Anchor, dia. 4.5mm/5.5 mm, loaded with one Fiber Wire, (USP Size 2) and one Fiber tape size 1.4mm, loaded on disposable driver – Sterile |
| 329 | Rotator Cuff repair kit (PEEK) - SterileComprises of : PEEK Suture Anchor, dia. 4.5 mm/ 5.5mm, loaded with one Fiber Wire (USP Size 2) and one Fiber Tape Size 1.4mm, loaded on a disposable driver (2 pcs)PEEK Suture Anchor, Knotless, dia. 4.75mm/ 5.5mm, for lateral row / double row repair, loaded on disposable driver (1 pcs)Disposable Shaver Blade Aggressive Full Radius Plus dia 4.2mm (1 pcs)Disposable Cannula Trocar Set dia. 6.5mm (1 pcs)Disposable Cannula Trocar Set dia. 8.5mm (1 pcs) Disposable Nitinol Flexible Needle for the automatic suture passer for Knee/Shoulder (1 pcs)Disposable RF Probe 90° (1 Pcs) |
| 330 | Rotator Cuff repair Kit (Biocomposite Absorbable) - SterileComprises of : Biocomposite Absorbable Suture Anchor, dia. 4.5mm/5.5mm, loaded with one Fiber Wire, (USP Size 2) and one Fiber tape size 1.4mm, loaded on Disposable driver - (2 pcs)Biocomposite Absorbable Suture Anchor, Knotless, dia. 4.75mm/5.5 mm, for Lateral Row / Double Row repair, PEEK eyelet, loaded on a Disposable driver (1 pcs)Disposable Shaver Blade Aggressive Full Radius Plus dia 4.2mm (1 pcs)Disposable Cannula Trocar Set dia. 6.5mm (1 pcs)Disposable Cannula Trocar Set dia. 8.5mm (1 pcs) Disposable Nitinol Flexible Needle for the automatic suture passer for Knee/Shoulder (1 pcs)Disposable RF Probe 90° (1 Pcs) |
| 331 | Titanium Suture Anchor, dia. 2.8mm, loaded with one Fiber Wire (USP Size 2), loaded on disposable driver – Sterile |
| 332 | PEEK Suture Anchor, dia. 2.8mm, loaded with one Fiber Wire (USP Size 2), loaded on disposable driver – Sterile |
| 333 | PEEK Suture Anchor, dia. 2.8mm, knotless, loaded on disposable driver – Sterile |
| 334 | PEEK Suture Anchor, dia. 3.0mm, double-loaded with Fiber Wire (USP Size 2)(different colors), loaded on a disposable driver – Sterile |
| 335 | All-Suture Anchor/ Soft Anchor, dia. 1.5mm, loaded with one Fiber Wire (USP Size 2), loaded on a flexible disposable driver – Sterile |
| 336 | All-Suture Anchor/ Soft Anchor, dia. 1.8mm, double-loaded with Fiber Wire (USP Size 2)(different colors), loaded on a flexible disposable driver – Sterile |
| 337 | All-Suture Anchor/ Soft Anchor, dia. 1.8mm, knotless, with one Fiber Wire (USP Size 2) and pulling fiber loop, loaded on a flexible disposable driver – Sterile |
| 338 | Bankart Repair Kit (All Suture) -SterileComprises of : All-Suture Anchor/ Soft Anchor, dia. 1.8mm, knotless, with one Fiber Wire (USP Size 2) and pulling fiber loop, loaded on a flexible Disposable driver – (4 Pcs)Disposable Suture Passer 45°, Left/Right (1pcs)Disposable Nitinol Loop Wire for Suture Passer (1 Pcs)Disposable Shaver Blade Aggressive Full Radius Plus dia 4.2mm (1 pcs)Disposable Cannula Trocar Set dia 6.5mm (1 pcs)Disposable Cannula Trocar Set dia 8.5mm (1 pcs) Disposable Nitinol Drill bit for all Suture Anchor/ Soft Anchor (1 pcs) |
| 339 | Bankart Repair Kit (PEEK) - SterileComprises of : PEEK Suture Anchor, dia. 2.8mm, knotless, loaded on Disposable driver – Sterile (4 pcs)Fiber Tape Size 1.4 , Len 38\\", with both end round, Tape working length 30\\" (Colour : White-Blue, White-Black) - Sterile (4 pcs)Disposable Suture Passer 45°, Left/Right (1pcs)Disposable Nitinol Loop Wire for Suture Passer (1 Pcs)Disposable Shaver Blade Aggressive Full Radius Plus dia 4.2mm (1 pcs)Disposable Cannula Trocar Set dia 6.5mm (1 pcs)Disposable Cannula Trocar Set dia 8.5mm (1 pcs) |
| 340 | Acromioclavicular Joint Repair Titanium Attachable Button with Two Side Open for ACJ (Chronic) Repair – Sterile |
| 341 | AC Joint (Acute) Repair Kit with One Oblong Button,Ti round Tapered Washer with Adjustable Loop (Knotless) loaded on Threaded Introducer – Sterile |
| 342 | Titanium Flat Head Cannulated Self-Tapping Screw, Dia 3.75mm, Length 28 mm to 40 mm, for Open Latarjet System (Assorted Sizes) - Sterile |
| 343 | Adjustable Fiber Loop with dia 2.5mm,Ti Oblong Button and Ti round Tapered Button , Knotless Kit loaded on Threaded Introducer - Sterile |
| 344 | Titanium Suture Anchor, dia 2.8mm, loaded with one Fiber Wire (USP Size 2) with Needle loaded on disposable driver - Sterile |
| 345 | Titanium Suture Anchor, dia 3.5mm, Double-Loaded Fiber Wire (USP Size 2)(different colors) with Needle, loaded on disposable Driver - Sterile |
| 346 | PEEK Suture Anchor, dia 3.0mm, Double-Loaded Fiber Wire (USP Size 2)(different colors) with Needle, loaded on disposable Driver - Sterile |
| 347 | PEEK Suture Anchor, dia 4.5mm/ 5.5mm, Double-Loaded Fiber Wire (USP Size 2)(different colors) with Needle, loaded on disposable Driver - Sterile |
| 348 | PEEK Suture Anchor, Knotless, dia. 3.5mm, Open eyelet with Screw (Total Length 12.5mm), loaded on disposable driver – Sterile |
| 349 | Biocomposite Suture Anchor, dia 4.5mm/ 5.5mm, Double-Loaded Fiber Wire (USP Size 2)(different colors) with Needle, loaded on disposable Driver - Sterile |
| 350 | All-Suture Anchor/ Soft anchor, dia. 1.5mm/ 1.8mm, Single / Double-Loaded with Fiber Wire (USP Size 2)(different colors) , with Needle, loaded on disposable Driver - Sterile |
