|
| 1 | Dismantling Old Plaster or Skirting Racking out joint and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metars lead. DAR No-15.56 |
| 2 | 15 mm thick Cement Plaster with Cement mortar in proportion of mix 1:4 (1 cement : 4 coarse sand) DSR-13.5.1, |
| 3 | Removing White or Colour wash by Scrapping and sand papering and preparing the surface smoothincluding necessary repairs to scratches etc. complete. DSR-13.88, |
| 4 | Providing and Applying white Cement based Putty of average thickness 1 mm. of approved brand and manufacture. Over the Plastered wall Surface to Prepare the Surface even and Smooth Complete. (DSR-13.80), |
| 5 | Wall Painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) Content less than 50 grams/litre of approved brand and manufacture, lncluding applying additional coats wherever required, to achieve even shade and colour. Two Coat, DSR.N0-13.82.2), |
| 6 | Finishing wall with Premium Acrylic Smooth exterior Paint with Silicone Additives of required Shade Old work. (Two or More Coats applied @1.43 ltr/10 sqm) Over Existing Cement Paint Surface. (DSR-13.112.1), |
| 7 | Painting with Synthetic enamel paint of approved brand and manufacture of required colour to give an even shade two of more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. DSR.N0-13.62.1), |
| 8 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot Finished welded type tubes DSR No-10.16.1, Rs-194.4/153.56) |
| 9 | Providing and Fixing of UV Stabilised Fiberglass reinforced Plastic Sheet Roofing up to any Pitch, including Fixing with Polymer Coated 'J' or 'L' hooks, bolts & nuts 8 mm dia, G.l. Plain/bitumen Washers Complete but excluding the Cost of Purlins, Rafters, Trusses etc. the Sheets shall be manufactured out of 2400 TEX Panel Roving Incorporating Minimum 0.3%, Ultra-Violet Stabiliser in resing system under approximately 2400 PSl and hot Cured. they Shall be of Uniform Pigmentation and thickness without air Pockets and shall Conform to IS 10192 and IS 12866. the Sheets Shall be Opaque or translucent, Clear or Pigmented Textured or Smooth as Specified. 2 mm thick Corrugated (2.5'' or 4.2'' or 6'') or Step-Down (2'' or 3'' or 6'' ) as Specified. DSR N0-12.47.1, (Rs-1401.35/1107.00) |
| 10 | Providing And Fixing Fly Proof galvanized M.S. wire gauge to windows and Clerestory window using wire gauge with average widht of aperture 1.4 mm both directions with wire of dia 0.63 mm all complete with second class teak wood beading 62x19 mm. DSR No-9.51.1, |
| 11 | Providing and fixing ISI marked flush door Shutters Conforming to IS : 2202 (Part I) Non decorative type core of block board construction with frame lst class hard wood and well matched commercial 3 ply Veneening with vertical graints or cross brand and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt Hinges with Necessary Screws. DAR N0-9.21.1, |
| 12 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door widht upto 700 mm), with necessary accessories and screws etc. complete. DAR-9.83, Rs-1124.85/888 |
| 13 | Providing and fixing brass Curtain Rods of wall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete. 25 mm dia meter. DAR-14.28.2, |
| 14 | Providing and fixing bright finished brass lower bolts (barrel type) with necessary screws etc complete. 250x10 mm (DAR -9.74.1) |
| 15 | Providing and fixing bright finished brass lower bolts (barrel type) with necessary screws etc complete. 200x10 mm (DAR -9.74.2) |
| 16 | Providing and fixing C.P. Brass Stop cock (Concealed) Standerd desingn and approved make conforming to IS:8931. 15 mm nominal bore ( 18.52.1) |
| 17 | Providing and fixing C.P. Brass Angle Valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15 mm nominal bore ( 18.53.1) |
| 18 | Providing and fixing C.P. Brass extentsion nipple (Size-15x50mm) of approved make and quality as per direction of engineer-in-charge. ( 18.53A) |
| 19 | Providing and fixing ball valve brass (brass ) of approved quality, high or low pressure, with plastic floats complete: ( 20 mm nominal bore) 18.18.2 |
| 20 | Providing and fixing ball valve brass (brass ) of approved quality, high or low pressure, with plastic floats complete: ( 25 mm nominal bore) 18.18.3 |
| 21 | Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. Note - item to be applicable in urban areas having directions for restricted hours for movement/plying of load carrying motor vehicle of 3.5 cum or more. DAR-1.1.18, Please Enable Macros to View BoQ information |
