|
| 1 | Seating and Satanding twisterDIMENSIONS : 1700mm(L)x540mm(W)x1250mm(H). (ii). SAFE AREA : 3Mtr X 1Mtr. (iii).Seating & Standing Twister equipment made from ''B'' Class G.I pipe of different NB, NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters(iv). The Center pipe is of 100mm NB made from ''B'' Class G.I Round Pipe.(v). The MS round plate of Dia 250mm and 10mm thickness is welded at bottom.(vi). Handle and Bottom sleeve pipe of 125mm OD with thickness 5mm provided for easy assembly, replacement and maintenance. (vii).The Bottom frame of the Seating & Standing twister is of 32 NB, 50 NB, and 25 NB made from \\"B\\" class G.I pipe. (viii). The handle frame of Seating & Standing Twister is 25 NB & Foot resting frame of seating side is made from \\"B\\" class G.I pipe of 25mm NB.(ix). The foundation used for fixing is a structureand made from center pipe of G.I of 80 NB \\"B\\"class, Welded with M.S Round Plate of size Dia 250mm and 10mm Thickness. Main pipe supported with 25mm x 25mm M.S anglesof 3mm thickness and 20mm x 40mm CRCA square pipe of 3mm thickness.(x). The twister plate fitted on the bottom frame is made up of Injection Moulded plastic LLDPE/HDPE and Mounted on M.S Round Plate of size Dia 300mm and 10mm Thickness.(xi). Closing Caps are made up of Injection Moulded Plastic LLDPE/HDPE.(xii). The Pins used are made up Dia 35mm SAE 8620 bright material.(xiii). The bearing used are of \\"6205zz\\" permanent lubricated sealed bearing of reputed brand.(xiv). High tensile steel with galvanized nuts & bolts are used for assembly.(xv). The powder coating is done by pure Polyester powder of Berger Piant with 60 to 70 micron thickness. (xvi). Installtion including with civil work. |
| 2 | Sky Walker(i). DIMENSIONS : 1720mm(L)x630mm(W)x1750mm(H).(ii). SAFE AREA : 2.7Mtr X 1.6Mtr.(iii). Sky Wlaker equipment made from ''B'' Class G.I pipe of different NB, NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters(iv). The Main frame pipe is of 80mm NB made from ''B'' Class G.I Material which is bend at the radius of 250mm.(v). The leg movement frame is of 50mm x 50mm and 3mm thick CRC square pipe.(vi). sleeve are made up of 100mm OD M.S pipe with thickness 5mm. this results in easy replacement of berings, pins and handle.(vii). The handle frame is of 25mm NB made from \\"B\\" class G.I pipe.(viii). The foundation used for fixing is a structureand made from center pipe of G.I of 80 NB \\"B\\"class, Welded with M.S Round Plate of size Dia 250mm and 10mm Thickness. Main pipe supported with 25mm x 25mm M.S anglesof 3mm thickness and 20mm x 40mm CRCA square pipe of 3mm thickness. two foundations are provided for rigid support.(ix). The footrests made from Injection Moulded plastic LLDPE/HDPE.(x). Closing Caps are made up of Injection Moulded Plastic LLDPE/HDPE.(xi). The Pins used are made up Dia 25mm SAE 8620 bright material. Pins are fixed at the outer end with M8 grub screws and Dia 8nn SS ball.(xii). The bearing used are of \\"6205zz\\" permanent lubricated sealed bearing of reputed brand.(xiii). High tensile steel with galvanized nuts & bolts are used for assembly.(xiv). The cerclips used for assembly are of A24 type.(xv). The powder coating is done by pure Polyester powder of Berger Piant with 60 to 70 micron thickness. (xvi). Installtion including with civil work. |
| 3 | Quad SpinnerQUAD SPINNER(i). DIMENSIONS : 1500mm(L)x 1500mm(W)x 1800mm(H).(ii). SAFE AREA : 3Mtr X 1Mtr.(iii). Quad Spinner Four Wheeler equipment made from ''B'' Class G.I pipe of different NB, NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters.(iv). The Center pipe is of 100mm NB made from ''B'' Class G.I Round Pipe.(v). The bottom welded with support of MS round plate of Dia 250mm and 10mm thickness.(vi). The handle movement frame is of 25mm NB made from \\"B\\" Class G.I pipe.(vii). The foundation used for fixing is a structureand made from center pipe of G.I of 80 NB \\"B\\"class, Welded with M.S Round Plate of size Dia 250mm and 10mm Thickness. Main pipe supported with 25mm x 25mm M.S anglesof 3mm thickness and 20mm x 40mm CRCA square pipe of 3mm thickness.(viii). Foundation cover Closing Cap is made from Injection Moulded Plastic LLDPE/HDPE.(ix). Closing Caps are made up of Injection Moulded Plastic LLDPE/HDPE.(x). The Pins used are made up Dia 25mm SAE 8620 bright material.(xi). The bearing used are of \\"6201zz\\" & \\"6205zz\\" permanent lubricated sealed bearing of reputed brand.(xii). High tensile steel with galvanized nuts & bolts are used for assembly.(xiii). The cerclips used for assembly are of A24 type.(xiv). The nylon bush is used for handle knob,(xv). The powder coating is done by pure Polyester powder of Berger Piant with 60 to 70 micron thickness. (xvi). Installtion including with civil work. |
| 4 | Back ExtensionDIMENSIONS : 1500mm(L) x 600mm(W) x 1350(H).(ii). SAFE AREA : 2.4 Mtr X 1.7 Mtr.(iii). Back Extension equipment made from ''B'' Class G.I pipe of different NB, NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters(iv). 50mm NB:- Main Frame.(v). 32mm NB:- Footrest support frame, Foundation hole-pass.(vi). 25mm NB:- Handle Frame.(vii). MS Angle 23 x 23 x 1.8mm :- Foundation support frame.(viii). MS Sheet of size 330 x 330 x 1.8mm :- Seat.(ix). MS plate of 245 x 113 x 2.8mm :- Footrest support plate.(x). Nut & Bolts :- High tensil steel with galvanised nut & bolts are used.(xi). HDPE/LLDPE Plastic:- Footrest.(xii). Handle grips :- Handle grips are made up of high quality rubber material.(xv). Powder coating :- The powder coating is done with pure Polyester powder of Berger Piant with 60 to 70 micron thickness. (xvi). Installtion including with civil work. |
| 5 | Chest Cum Seated Puller(i). DIMENSIONS : 2000mm(L)x710mm(W)x2200mm(H).(ii). SAFE AREA : 3Mtr x 1.7Mtr.(iii). Chest press cum seated puller equipment made from ''B'' Class G.I pipe of different NB, NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters(iv). The Center pipe is of 100mm NB made from ''B'' Class G.I Round Pipe.(v). The bottom welded with support of MS round plate of Dia 250mm and 10mm thickness.(vi). The connecting pipe are made up from 25NB \\"B\\" Class G.I. pipe.(vii). The handle frame is made up from 32NB made from \\"B\\" Class G.I pipe.(viii). The build structure bushes are used which are made from seamless pipe of 50mm OD and thickness as well as 50mm diameter soild bar is used.(ix). The foundation used for fixing is a structureand made from center pipe of G.I of 80 NB \\"B\\"class, Welded with M.S Round Plate of size Dia 250mm and 10mm Thickness. Main pipe supported with 25mm x 25mm M.S anglesof 3mm thickness and 20mm x 40mm CRCA square pipe of 3mm thickness.(x). The seats and back rest are fitted on outer frames are made up of MS Sheet of size 330mm x 300mm x 2mm thickness and deep drawn and pressed in tools and dies to have uniform raduis of 20mm with no sharp edges.(xi). Foundation cover Closing Cap is made from Injection Moulded Plastic LLDPE/HDPE..(xii). Closing Caps are made up of Injection Moulded Plastic LLDPE/HDPE.(xiii). The Pins used are made up Dia 25mm SAE 8620 bright material.(xiv). The bearing used are of \\"6205zz\\" & \\"6203zz\\" permanent lubricated sealed bearing of reputed brand.(xv). High tensile steel with galvanized nuts & bolts are used for assembly.(xvi). The cerclips used for locking is made up of A24 & A16.(xvii). The powder coating is done by pure Polyester powder of Berger Piant with 60 to 70 micron thickness. (xviii).Installtion including with civil work. |
| 6 | Leg Press DIMENSIONS : 1840mm(L)x360mm(W)x1560mm(H). (ii). SAFE AREA : 2.8 Mtr x 1.4 Mtr. (iii). Leg Press equipment made from ''B'' Class G.I pipe of different NB, NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters(iv). The Center pipe is of 100mm NB made from ''B'' Class G.I Round Pipe.(v). The Sleeve frame is of 100mm OD and of MS Seamless pipe with thickness 5mm. This sleeve can be disassembled from main frame.(vi). The bottom support of MS round plate of Dia 250mm and 10mm thickness.(vii). The remaining outer frame is of 32NB made from \\"B\\" c;ass G.I pipe.(viii). The foundation used for fixing is a structureand made from center pipe of G.I of 80 NB \\"B\\"class, Welded with M.S Round Plate of size Dia 250mm and 10mm Thickness. Main pipe supported with 25mm x 25mm M.S anglesof 3mm thickness and 20mm x 40mm CRCA square pipe of 3mm thickness.(ix). The seats and back rest are fitted on outer frames are made up of MS Sheet of size 330mm x 300mm x 2mm thickness and deep drawn and pressed in tools and dies to have uniform raduis of 20mm with no sharp edges.(x). The footrests made from Injection Moulded plastic LLDPE/HDPE with the support of 310mm x 130mm and 3mm thick MS Plate.(xi). The frame of footrests made up of 25 NB \\"B\\" class G.I pipe.(xii). Foundation cover Closing Cap is made from Injection Moulded Plastic LLDPE/HDPE.(xiii). Closing Caps are made up of Injection Moulded Plastic LLDPE/HDPE.(xiv). The Pins used are made up Dia 25mm SAE 8620 bright material.(xv). The bearing used are of \\"6205zz\\" permanent lubricated sealed bearing of reputed brand.(xvi). High tensile steel with galvanized nuts & bolts are used for assembly.(xvii). The powder coating is done by pure Polyester powder of Berger Piant with 60 to 70 micron thickness. (xviii). Installtion including with civil work. |
| 7 | Shoulder Builder(i). DIMENSIONS : 900mm(L)x900mm(W)x1580mm(H).(ii). SAFE AREA : 1.9 Mtr x 1.9 Mtr.(iii). Shoulder Builder equipment made from ''B'' Class G.I pipe of different NB, NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters(iv). The Center pipe is of 100mm NB made from ''B'' Class G.I Round Pipe and bottom support of MS round plate of 250mm Dia and 10mm thickness.(v). Sleeve provided is of MS Seamless pipe outer diameter 125mm with thickness 5mm provided. (vi). Thehandle movement frame is of 25mm NB made from \\"B\\" class G.I Pipe.(viii). The foundation used for fixing is a structureand made from center pipe of G.I of 80 NB \\"B\\"class, Welded with M.S Round Plate of size Dia 250mm and 10mm Thickness. Main pipe supported with 25mm x 25mm M.S anglesof 3mm thickness and 20mm x 40mm CRCA square pipe of 3mm thickness.(viii). Closing Caps are made up of Injection Moulded Plastic LLDPE/HDPE.(ix). The Pins used are made up Dia 25mm SAE 8620 bright material.(x). The bearing used are of \\"6205zz\\" permanent lubricated sealed bearing of reputed brand.(xi). High tensile steel with galvanized nuts & bolts are used for assembly.(xiii). The cerclips used for assembly are of A24 type.(xiii). The nylon bush is used for handle knob,(xiv). The powder coating is done by pure Polyester powder of Berger Piant with 60 to 70 micron thickness.(xv). Foundation cover Closing Cap is made from Injection Moulded Plastic LLDPE/HDPE.(xvi). Installtion including with civil work. |
| 8 | SURF BOARD (i).DIMENSIONS : 910mm(L)x860mm(W)x1400mm(H). (ii). SAFE AREA : 1.39 Mtr x 1.27 Mtr.(iii). Surf Board equipment made from ''B'' Class G.I pipe of different NB, NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters(iv). The Center pipe is of 100mm NB made from ''B'' Class G.I Pipe.(v). The Sleeve frame is of 125mm OD and of MS Seamless pipe with thickness 5mm and bolted to main frame with M10 SS bolts.(vi). The bottom support welded of MS plate of OD 250mm and 10mm thickness.(vii). The handle movement frame is of 25mm NB made from \\"B\\" class G.I Pipe.(viii). The paddle frame is of 50NB made from \\"B\\" class G.I pipe supported with 70x8mm bend MS flat and can be replaceable.(ix). The foundation used for fixing is a structureand made from center pipe of G.I of 80 NB \\"B\\"class, Welded with M.S Round Plate of size Dia 250mm and 10mm Thickness. Main pipe supported with 25mm x 25mm M.S anglesof 3mm thickness and 20mm x 40mm CRCA square pipe of 3mm thickness.(x). Bushes are used 70m OD with 5mm thickness is used.(xi)The footrest made from InjectionMoulded Plastic LLDPE/HDPE.(xii). Footrest support 200mm x 250mm with 3mm thickness MS plate used.(xiii). Closing Caps are made up of Injection Moulded Plastic LLDPE/HDPE.(xiv). The Pins used are made up Dia 35mm SAE 8620 bright material.(xv). The bearing used are of \\"6207zz\\" permanent lubricated sealed bearing of reputed brand.(xvi). High tensile steel with galvanized nuts & bolts are used for assembly.(xvii). The cerclips used for assembly are of A34 type.(xviii). The powder coating is done by pure Polyester powder of Berger Piant with 60 to 70 micron thickness. |
| 9 | SIT UP BOARD (i). DIMENSIONS : 1820mm(L)x430mm(W)x580mm(H). (ii). SAFE AREA : 2.8 Mtr x 0.6 Mtr. (iii). Sit UP Board equipment made from ''B'' Class G.I pipe of different NB, NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters(iv). The main frame is of 50mm NB made from \\"B\\" class G.I pipe supportedwith the MS round plate of OD 250 and 10mm thickness.(v). Fiber reinforced Plastic sheet of 3mm thickness is Bounded on 25mm NB \\"B\\" calss G.I pipe of maine frame.(vi). The base support of the sit up board is made 40NB \\"B\\" class G.I pipe.(vii). The foundation used for fixing is a structureand made from center pipe of G.I of 80 NB \\"B\\"class, Welded with M.S Round Plate of size Dia 250mm and 10mm Thickness. Main pipe supported with 25mm x 25mm M.S anglesof 3mm thickness and 20mm x 40mm CRCA square pipe of 3mm thickness.(viii). The powder coating is done by pure Polyester powder of Berger Piant with 60 to 70 micron thickness.(ix). Installtion including with civil work. |
| 10 | Cycle DIMENSIONS : 1570mm(L)x570mm(W)x900mm(H). (ii). SAFE AREA : 2.5 Mtr x 1.5 Mtr. (iii). Cycle equipment made from ''B'' Class G.I pipe of different NB, NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters.(iv). The main frame is of 25mm NB made from \\"B\\" class G.I pipe.(v). MS round plate of OD 300mm and 10mm thickness used to from a paddle assembly.(vi). The handle frame is of 25NB made from \\"B\\" class G.I pipe.(vii). The seats and back rests are fitted on the outer frames are made up of MS sheet of size 330 x 300mm and 2mm thickness and deep drawn and pressed in tools and dies to have uniform raduis of 20mm with no sharp edges.(viii). The foundation used for fixing is a structureand made from center pipe of G.I of 80 NB \\"B\\"class, Welded with M.S Round Plate of size Dia 250mm and 10mm Thickness. Main pipe supported with 25mm x 25mm M.S anglesof 3mm thickness and 20mm x 40mm CRCA square pipe of 3mm thickness.(ix). Closing Caps are made up of Injection Moulded Plastic LLDPE/HDPE.(x). Pins used of Diameter 25mm are made up from SAE 8620 bright material.(xi). Pins used of Diameter 13mm are made up from EN8 material with CRAC pipe 20x20mm of thickness 3mm for paddle assembly.(xii). The bearing used are 6001zz & 6205zz permanent lubricated sealed bearing of reputed brand. (xiii). High tensile steelwith galvanized nuts & bolts are used for assembly. (xiv). The cerclips used for assembly are of A24 type.(xv). The powder coating is done by pure Polyester powder of Berger Piant with 60 to 70 micron thickness. (xvi). Installtion including with civil work. |
| 11 | HORSE RIDER (i).DIMENSIONS : 1200mm(L) x 600mm(W) x 1100mm(H).(ii). SAFE AREA : 2.2 Mtr x 1.4 Mtr.(iii). Horse Rider equipment made from ''B'' Class G.I pipe of different NB, NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters.(iv). The main frame of 100NB made from \\"B\\" class G.I pipes welded with MS round plate of OD 250mm & 10mm thick.(iv). The seats and Back rests are fitted on the outer frames are made up of MS Sheet of size 330mm x 300mm x 2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20mm with no sharp edges.(v). Foundation cover closing cap is made from Injection Moulded Plastic LLDPE/HDPE.(v). The foundation used for fixing is a strucure and made from center pipe of GI of 80 NB \\"B\\" class Welded with MS round plate of OD 250mm x 40mm CRC square pipes of 3mm thickness.(vi). MS angles of 20mm x 40mm and 3mm thickness .(vii). The leg movement frame is of 32 NB made from \\"B\\" class GI pipe .(viii). The handle frame is of 32 NB made from \\"B\\" class G.I pipe..(ix). The footrest are made from 25 NB \\"B\\" class G.I pipe.(x). The Pins used are made up Dia 17mm SAE 8620 bright material.(xi). The bearing used are of \\"6203zz\\" permanent lubricated sealed bearing of reputed brand.(xii). High tensile steel with galvanized nuts & bolts are used for assembly.(xiii). The cerclips used for assembly are of A24 type.(xiv). The powder coating is done by pure Polyester powder of Berger Piant with 60 to 70 micron thickness. (xv).Installtion including with civil work. |
| 12 | LEG EXTENSION(i). DIMENSIONS : 1000mm(L)x 680mm(W)x 1600mm(H).(ii). SAFE AREA : 2 Mtr x 1.4 Mtr.(iii). Leg Extension equipment made from ''B'' Class G.I pipe of different NB, NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters.(iv). Center pipe :- 1000mm NB.(v). Foundation main pipe :- 80mm NB.(vi). Pedal Link :- 32mm NB.(vii). Handle frame duly bend, Footrest :- 25mm NB.(viii). MS Angle 23x23 and 1.8mm Thick :- Foundation support frame.(ix). Bearings :- Permanent lubricated bearings \\"6203\\" of reputed brand are used.(x). Bearing End cap :- Made up from SS304/Nylon material.(xi). Bsae Cover :- HDPE/LLDPE.(xii). Nut & Bolts :- High tensile steel with galvanised nut & bolts are used.(xiii). Circlips :- The circlips are used for locking is made up of A16.(xiv). The powder coating is done by pure Polyester powder of Berger Piant with 60 to 70 micron thickness. (xv).Installtion including with civil work. |
| 13 | Pec DeckDIMENSIONS : 2000mm(L)x 710mm(W)x 2000mm(H).(ii). SAFE AREA : 3.0 Mtr x 1.7 Mtr.(iii). Pec Deck equipment made from ''B'' Class G.I pipe of different NB, NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters.(iv). Center pipe :- 1000mm NB.(v). Foundation main pipe :- 80mm NB.(vi). Handle frame, Seat frame, support :- 32mm NB.(vii). Connecting link Handle :- 25mm NB.(viii). Peck Deck small links :-15mm NB.(viii). Foundation support frame:- MS Angle 23x23 and 1.8mm Thick.(ix). Foundation support frame:- MS pipe 19mm x 38mm and 1.8mm thickness.(x). Peck Deck profile :- Ms plate of 8mm.(xi). Bushes :- OD 50mm seamless pipe.(xii). Bushes :- OD 60mm seamless pipe.(xiii). Seat and Backrest:- MS sheet of size 330mm x 330mm and thickness 1.8mm.(xiv). Ms bright material :- Pins made of Dia 25mm & Dia 17mm.(ix). Bearings :- Permanent lubricated bearings \\"6203\\" of reputed brand are used.(x). Bearing End cap :- Made up from SS304/Nylon material.(xi). Bsae Cover, Closing caps :- HDPE/LLDPE Plastic.(xii). Nut & Bolts :- High tensile steel with galvanised nut & bolts are used.(xiii). Circlips :- The circlips are used for locking is made up of A24 & A16.(xiv). The powder coating is done by pure Polyester powder of Berger Piant with 60 to 70 micron thickness. (xv). Installtion including with civil work. |
| 14 | PUSH UP BAR (i). DIMENSIONS : 1800mm(L)x 900mm(W)x 1350mm(H).(ii). SAFE AREA : 2.0 Mtr x 1.0 Mtr.(iii). Push up bar equipment made from ''B'' Class G.I pipe of different NB, NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters.(iv). Center pipe :- 100mm NB.(v). Foundation main pipe :- 80mm NB.(vi). Handle frame pipe support :- 32mm NB.(vii). Foundation support frame:- MS Angle 23x23 and 1.8mm Thick.(viii). Foundation support frame:- MS pipe 19mm x 38mm and 1.8mm thickness.(ix). Closing caps, Base cover :- HDPE/LLDPE Plastic.(x). Nut & Bolts :- High tensile steel with galvanised nut & bolts are used.(xi). The powder coating is done by pure Polyester powder of Berger Piant with 60 to 70 micron thickness. |
| 15 | UNEVEN BAR (i). DIMENSIONS : 3200mm(L)x 500mm(W)x 2200mm(H).(ii). SAFE AREA : 5.4 Mtr x 5.2 Mtr.(iii). Uneven bar equipment made from ''B'' Class G.I pipe of different NB, NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters.(iv). Foundation main pipe; Main frame duly bend :- 80mm NB.(v). Horizontal link, Handle frame duly bend:- 32mm NB.(vi). Handle frame duly bend :- 25mm NB.(vii). Foundation support frame:- MS Angle 23x23 and 1.8mm Thick.(viii). Foundation support frame:- MS pipe 19mm x 38mm and 1.8mm thickness.(ix). Closing caps :- HDPE/LLDPE Plastic.(x). Nut & Bolts :- High tensile steel with galvanised nut & bolts are used.(xi). The powder coating is done by pure Polyester powder of Berger Piant with 60 to 70 micron thickness. (x). Installtion including with civil work. |
| 16 | BENCH WITH FIXED DUMBBELL(i). DIMENSIONS : 2350mm(L)x 660(W)x 600mm(H).(ii). SAFE AREA : 3.5 Mtr x 2.0 Mtr.(iii). Bench with fixed dumbbell equipment made from ''B'' Class G.I pipe of different NB, NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters.(iv). The main frame having pipe 50mm NB made up of \\"B\\" class G.I pipe.(v). The middle connecting pipes are made up from 40mm x 20mm rectangular MS pipe.(vi). The handle frame is made up from 32NB \\"B\\" class GI pipe.(vii). The build structure bushes are used which are made from seamless pipe of 50mm OD and 6mm thickness as well as 25mm outer diameter solid bar is used.(viii). The structure having hole pass provision for foundation.(ix). Weight plates are made from iron casting material which is permanently attached with 25mm MS soild bar.(x). Shaft used of Dia 25mm made up from SAE 8620 bright material.(xi). Bearings :- Permanent lubricated bearings \\"6205zz\\" of reputed brand are used.(xii). Circlips :- The circlips are used for locking is made OD 25mm.(xiii). The powder coating is done by pure Polyester powder of Berger Piant with 60 to 70 micron thickness.(xiv). Installtion including with civil work. |
| 17 | Air WalkerDIMENSIONS : 1200mm(L)x 400mm(W)x 1290mm(H).(ii). SAFE AREA : 2.0 Mtr x 1.8 Mtr.(iii). Air Walker equipment made from ''B'' Class G.I pipe of different NB, NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters.(iv). Air Walker Prime stand duly bend, Foundation Center pipe :- 80mm NB.(v). Air Walker pedal frame :- 80mm NB.(vi). Air Walker Handle frame :- 32mm NB.(vii). Connecting link Handle :- 25mm NB.(viii). Foundation support frame:- MS Angle 23x23 and 1.8mm Thick.(ix). Footrest frame support:- MS pipe 48mm x 48mm and 2.8mm thickness.(x). Foundation plate support :- MS Flat 48mm x 9mm.(xi). Footrest support plate :- MS plate of 245mm x 113mm and 2.8mm thick.(xii). Ms bright material :- Pins made of Dia 25mm.(xiii).Air Walker pedal L-bend, support :- MS plate of 8mm .(xiv). Bushes:- OD 60mm seamless pipe . (xv). Bearings :- Permanent lubricated bearings \\"6205\\" of reputed brand are used.(xvi). Nut & Bolts :- High tensile steel with galvanised nut & bolts are used.(xvii). Circlips :- The circlips are used for locking is made up of A24.(xviii). Bearing end caps, top cap :- SS 304 material.(xix). The powder coating is done by pure Polyester powder of Berger Piant with 60 to 70 micron thickness. (xx). Installtion including with civil work. |
| 18 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and removing from the ste. |
| 19 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm |
| 20 | Grubbing up tree trunk including of trunk portion protrruding over ground digging out roots. Fillings holes and levelling off ground etc. |
| 21 | Demolition of brick work and removing from site. |
| 22 | Demolition of Cement Concrete and removing waste malba. |
| 23 | Excavation over and area n exc 1.5 mtr deep and getting out loose soil and removing from site. |
| 24 | Cement concrete in foundations, filling and mass concrete (1:2:4) |
| 25 | Cement concrete in foundations, filling and mass concrete (1:4:8, 40 mm graded agreegate) |
| 26 | Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:4 |
| 27 | Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match |
| 28 | Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match |
| 29 | Chequered cement concrete tiles 20cm x20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors |
| 30 | Screed bed or beddinglayer of mortar 15 mm thick for laying floor finishes |
| 31 | Painting brick, stone, concrete or plaster surfaces of any descriptions over 10 cm grith or width including prepration, priming paint plaster, synthetic enamel. Please Enable Macros to View BoQ information |
