Tender For Special Repairs To Samudra Building (P-29) To Facilitate Installation Of Newsagar -Iii System At 2N Det Vellachi Under Ge Navy Chennai
Tender Value
46 Lakhs
Estimated cost
Bid Submission
09 Jul 2026
1 days left
EMD
92000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chennai → Tamil Nadu
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repairs To Samudra Building (P-29) To Facilitate Installation Of Newsagar -Iii System At 2N Det Vellachi Under Ge Navy Chennai
BOQ
| Sl. No. | Item Description |
| 1 | Demolition cement concrete (unreinforced) in ground floors and paving n.exc 15cm thick (below & above ground level) |
| 2 | M&L for PCC 1:2:4 type B-1(using 20mm graded stone aggregate) 40 mm thick as in flooring and finishing surfaces even and smooth (without using extra cement) Complete all as specified and directed by Engineer-in-Charge. |
| 3 | M&L for 25mm thick PCC 1:2:4 type B0 (12.5mm graded stone aggregate) as in screed bed over sub base Complete all as specified and directed by Engineer-in-Charge. |
| 4 | Dismantling of wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises including removing of all the debris to a distance not exc 2 km out side the base Complete all as specified and directed by Engineer-in-Charge. |
| 5 | M&L for screed bed or bedding layer of cement mortar 1:6, 15 mm thick for laying floor finishes |
| 6 | M&L for 10mm thick screed plaster on fair faces of brick work/concrete in CM 1:3 to receive tiles as in dado Complete all as specified and directed by Engineer-in-Charge. |
| 7 | S&F Coloured non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 11 sqm but not exceeding 0.18 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match Complete all as specified and directed by Engineer-in-Charge. |
| 8 | M&L for glazed ceramic coloured tiles 350 x 250mm x7mm/450 X 350 X 7mm thick as in skirting/dados set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick backing coat on fair faces of brick work/concrete in CM 1:4 to receive tiles as in dado Complete all as specified and directed by Engineer-in-Charge. |
| 9 | S&F Double charged vitrified tiles 8 to 10 mm thick (Square/rectangular) area of each tile exceeding 0. 18 sqm but not exceeding 0.38 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 15mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified and as directed. |
| 10 | All as per item No 9 here in before but Double charged vitrified tiles in skirtings |
| 11 | S & F Chequered cement concrete tiles bullnosed 30 cm x 30 cm x 20 mm thick,as in treads with grey cement and pigments, set, jointed and pointed in neat cement slurry in treads including 20mm screed bed in CM 1:6 |
| 12 | Taking down chowkat or frame with shutters (without taking off shutters from the frames) not exc 1.5 sqm each. |
| 13 | Taking down Chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each(without taking off shutters from the frames) |
| 14 | S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification complete all as specified and as directed. |
| 15 | Supply & Fix Factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face as per specification complete all as specified and as directed. |
| 16 | S & F Second class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints. |
| 17 | S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides including 6mm thick teak wood lipping all as specified. |
| 18 | M&L 35mm thick 2nd class hard wood plain framed panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces.The size of rail and stile as per IS:1003 (Part1),kiln seasoned and chemically pressure treated, all as specified and directed. |
| 19 | S & F 30 mm thick second class hard made Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars) chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in SSR Pt I Section 8, clause 8.24 (a) |
| 20 | Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.) (A) Area not exceeding 2.00 sqm each. |
| 21 | Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.)comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc.Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass will be paid measured and paid separately). |
| 22 | Supply and fix Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of gradeAC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete as per requirement and direction of Engineer-in-charge. |
| 23 | S&F sheet glass ordinary quality 5.5 mm thick, in squares n exc. 0.5 sqm each pane complete all as specified. |
| 24 | S & F in repairs Aluminium alloy wire cloth, 0.45 mm dia of wire and average width of aperture 1.40 mm and fixed with stainless wire staples |
| 25 | S&F 100mm hinges extruded aluminium alloy with galvanised mild steel pin anodized and fixed type C-21 Complete all as specified and directed by Engineer-in-Charge. |
| 26 | S&F 125 mm butt hinges, medium weight, cold rolled mild steel and fixed |
| 27 | S&F 150mm size aluminium handle, cast type, anodised.Complete all as specified and directed by Engineer-in-Charge. |
| 28 | S&F 200 mm size aluminium anodised, barrel tower bolts of extruded section and fixed. |
| 29 | S&F 300mm long Aluminium, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded section all as specified. |
| 30 | S&F magic eye15mm dia steel body suitable for 35 to 40 mm th doors with all necessary fittings all as specified and direcetd by Engr-in-Charge |
| 31 | S & F Mild steel Angles, bars, flats etc., as in supports for stiffening of fencing, wall ties, hold fasts, clamps, plain angle cleats for securing purlins and similar small articles confirming to Fe 290 Gde E165 |
| 32 | M&L Providing PCC Type B1, 1:2:4 (20mm graded stone aggregate) as in hold fast etc Complete all as specified and directed by Engineer-in-Charge. |
| 33 | S & F couple of 25 mm of Stainless Steel fancy Glossy Matte Series Curtain Bracket Complete all as specified and directed by Engineer-in-Charge. |
| 34 | S&F in repair aluminium anodised tubular rail 20mm dia D type 60cm long between flanges including a pair of brackets for each towel rail. |
| 35 | S & F 150 mm door stopper of alumiminium alloy body, with rubber bush |
| 36 | S&F 300mm mild steel ordinary rat tail rod pattern springs incl roller and roller plates complete. |
| 37 | S & F in repairs Vitreous China wash down water closet pan (pedestal pattern), white (excluding , low level flushing cistern and Flush pipe of 32mm dia but including seat cover) complete all as specified and directed. |
| 38 | S&F in repairs PVC valve less flushing cistern low level 10 litres capacity with syphonic action type with inlet ball valves, float and handle and connections to pipes and fixing of chain and pull (or) lever including brackets and 32mm dia PVC flush pipe of 60cm long complete all as specified. |
| 39 | S & F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 40 | S&F in repair vitreous china, wash hand basin white flat back size 550 x 400 mm white complete waste, chain and plug and porcelain stopper including bracket complete |
| 41 | S & F 32 mm bore brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipes or connections including necessary packing union and cap. |
| 42 | Supply & fixing fancy type pillar tap 15mm dia, cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shank and fly nut screwed for iron pipe & fixed in repairs. |
| 43 | S&F for 32 mm bore High density polythylene pipes (HDPE) of pressure rating 6Kgf/cm2 fixed compete to in walls, floors,ceilings etc |
| 44 | S&F in repair bib taps concealed type with long shank and cup of fancy type,chromium plated screwed down high pressure with crutch or butterfly handle screwed for iron pipes of 15mm bore. |
| 45 | S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm |
| 46 | S & F PVC (SWR) multiple Floor trap of 75 mm outlet plain with grating including jointing with solvent cement. |
| 47 | S&F in repair Angle valves fancy type,chromium plated cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe of 15mm bore. |
| 48 | Supply and fixing Brass CP mixer of 20mm dia for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. |
| 49 | S&F in repair Brass chromium plated shower rose 125mm size, with or without swivel joints, including fixing to steel pipe or union. |
| 50 | S&F in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass 12cm wide with chromium plated bracket guard and railing 60cm long |
| 51 | S&F soap dish, vitreous China white, approximate size 160x160x90mm |
| 52 | Taking down cement plaster on brick walls including racking out joints, hacking for key, scrubbing down with water etc. |
| 53 | M & L Rendering for 10mm thick in cement mortar (1:6) on other than fair faces of internal bricks or concrete surfaces finished even and smooth without using extra cement all as specified and s directed.. |
| 54 | M&L for rendering 15 mm thick in two layers 10 mm thick backing coat in cm 1:6 and 5mm thick finishing coat in cm 1:4 . mixed with water proofing @ 2% by weight of cement with fair & even plasters finshes. (Note :- WPC will be measured and paid separately). |
| 55 | M & L Rendering 5mm thick on ceiling in CM 1:3 finished even and smooth without using extra cement. |
| 56 | M&L for preparing newly plastered surfaces and applying two coats of distemper oil emulsion over coat of primer on surfaces of walls including 3mm th wall care putty on walls |
| 57 | M & L prepartion of new plastered surface and finishing walls with Acrylic Smooth exterior emulsion paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and as directed. |
| 58 | M & L Preparing newly plastered surfaces of celings and applying three coats of white wash. |
| 59 | M & L for complete removal of existing treatment & prepartion of surfaces and Finishing walls with Acrylic Smooth exterior emulsion paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) by smart paint application method complete all as specified and as directed. |
| 60 | M & L complete removal of existing treatment & preparation of walls and applying two coat of distemper oil emulsion over a coat of primer on surfaces of walls including 3mm th wall care putty on walls by smart paint application method complete all as specified and as directed |
| 61 | M & L preparing old plastered surfaces of ceilings and applying one coat of white wash. |
| 62 | M & L preparing old plastered surfaces of walls and applying one coat of white wash. |
| 63 | M & L preparing new or previously untreated wooden surfaces of any description, exceeding 10 cm width or girth, not otherwise described and applying two coats of Synthetic Enamel paint over a coat of pink primer. |
| 64 | Taking up or down steel tubing 20mm dia bore and connection complete all as specified |
| 65 | Taking up or down steel tubing 25mm dia bore and connection complete all as specified |
| 66 | Taking up or down steel tubing 40mm dia bore and connection complete all as specified |
| 67 | Cutting chases, pinning in , for concealed water tubing on brick or stone walls, making good to facing where required and pointing in cement mortar 1:3, not exc 10 cm girth complete all as specified and directed. |
| 68 | Supplying and laying of CPVC pipes of outer dia 20mm dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 69 | Supplying and laying of CPVC pipes of outer dia 25mm dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 70 | Supplying and laying of CPVC pipes of outer dia 40mm dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 71 | Supplying and fixing CPVC Brass Elbow (3/4 x 1/2) as in special fittings |
| 72 | Supplying and fixing CPVC Brass Tee of 20mm dia as in special fittings |
| 73 | Supplying and fixing CPVC 40mm dia Male Brass Threaded Adaptor (MTA/ MBTA) ) as in special fittings |
| 74 | Supplying and fixing CPVC 40mm dia UNION as in special fittings |
| 75 | Supplying and fixing CPVC 25mm dia UNION as in special fittings |
| 76 | S & F in repairs Gun metal globe or gate valve 40 mm dia of pipe with Iron wheel head, screwed both end for Iron pipe one fixed. |
| 77 | Taking down rain water pipe and sewage pipe of any size of pattern including all fittings, heads, shoes, bends etc. |
| 78 | S&F for 110mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls. |
| 79 | S&F for 75mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls. |
| 80 | S&F for 75mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring jointslaid in trenches or floors |
| 81 | S&F for 110mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or floors |
| 82 | S&F for 75mm dia bore PVC (SWR) branch piece, single (Single 'Y') equal or unequal with access door |
| 83 | S&F for 110mm dia bore PVC (SWR) junction single, (Single 'T') equal or unequal with access door |
| 84 | S&F for 75mm dia bore PVC (SWR) bends any radius. |
| 85 | S&F for 110mm dia bore PVC (SWR) bends any radius |
| 86 | S&F for 110mm dia bore PVC (SWR) vent cowl. |
| 87 | S&F for 75mm dia bore PVC (SWR) vent cowl. |
| 88 | Surface Excavation not exceeding 30 Cm deep and averaging 15 Cm deep and getting out in Soft/ Loose soil complete all as specified and as directed. |
| 89 | M&L hardcore of gauge exc 63mm deposited ,spread &levelled in layers n exc 15cm thick,watered and rammed to a true surface. |
| 90 | M & L 75 mm thick Cement concrete type C2, 1:3:6 (using 40 mm graded stone aggregate) in sub base of flooring/ hard standing/pavings/plinth protections. |
| 91 | M&L ATT for treating the soil under plinth protection at the rate of 5.0 ltr of emulsion per sqm of surface area |
| 92 | M&L ATT for treating the soil along with external perimeter of building at the rate of 2.25. ltr of emulsion per mtr of the perimeter walls. |
| 93 | M & L ATT by injecting at point of contact of wood work by chemical emulsion (oil or kerosene based solution)@ 0.5 lit/ hole by driling 6mm dia hols at downward angle of 45 degrees at 150 mm centre to centte and sealing the same all as specifiled . |
| 94 | M & L ATT Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm part including drilling and plugging 12mm dia holes with cement mortar 1:2 to match the existing floors. |
| 95 | Demolition of stone slabs and tiles of any description or any thickness in floors, skirtings, risers etc laid ,bedded and pointed in any mortar. |
| 96 | M & L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over rendering 15 mm thick in CM 1:6 complete all as specified.. |
| 97 | Providing edge moulding/ Full nosing to 18-20mm thick Granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete |
| 98 | S & F in repairs Ball brass valves of 25mm dia, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed in repairs |
| 99 | Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles |
| 100 | M&L for brick work with fly ash modular bricks, straight or curved on plan exc. 6m mean radius built in CM 1:6 complete all as specified and directed. |
| 101 | Demolition of Reinforced cement concrete (Reinforcement cut as required ) of any description and in any position not otherwise specifically provided including padding concrete on roof all as specified and directed. |
| 102 | M & L TMT bars 10mm dia and over, cut to length, bent to shape equired, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips |
| 103 | All as per item no 102 here in before but 6mm to 8mm diaTMT bars |
| 104 | S&F of Rotational moulded polyethylene 1000 Litrs water storage tanks (cylindrical vertical with closed top)3 layered, hoisted and fixed in position all as specified in SSR Part I |
| 105 | S&F frame work for seamless ceiling comprising of GI framework with perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm center to center/ intermediate channel 0.9mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm center to center with GI cleat and steel expansion fasteners with and including ceiling section (not exc. 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lip of 10.5 mm fixed to the intermediate channel at 457 mm center to center complete all as per manufacturer's instructions and as directed by Engineer-in Charge. |
| 106 | S & F Hangers 6mm dia G>I (Upto 1200mm length ) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long omplete all as specified and directed by Engineer-in-Charge. |
| 107 | M&L for 12 mm thick seamless calcium silicate false ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having philips head with under head cutter at 200 mm centre to centre, including finishing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish Complete all as specified and directed by Engineer-in-Charge. Note: Frame work for ceiling shall be measured and paid separately |
| 108 | Material and Labour for preparation of celing surfaces and applying two coats of distemper oil-emulsion over 2mm putty complete all as specified and directed by Engineer-in-Charge. |
| 109 | Demolition of padding concrete in roofs, any thickness, existing roof treament of any description in any condition including removing top surface and removing all the debries Complete all as specified and directed by Engineer-in-Charge. |
| 110 | Demolition of roof treament on verticle surfaces in roofs parapet walls any thickness, existing roof treament of any description in any condition including removing top surface and removing all the debries Complete all as specified and directed by Engineer-in-Charge. |
| 111 | Removing of debries any description obtained from demolition beyond the lead included in the rates including loading unloading to a distance exceeding 1.5Km and not exceeding 2.00 KM out side defence land Complete all as specified and directed by Engineer-in-Charge. |
| 112 | Cutting grooves in brick/concrete wall, 75mm wide and 65mm deep and shaping horizontal face of grooves with cement mortar 1:3`complete all as specified and as directed. |
| 113 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and applying evenly cement slurry @3Kg/Sqm over cleaned roof surface all as specified and as directed by the Engr-in -charge. |
| 114 | M&L PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) as in padding concrete to maintain required slope including coving to junctions of parapet and roofs complete all as specified and directed by Engineer-in-Charge. |
| 115 | M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces with cement plaster 1:3 with WPC @ 2% by weight of cement (Note : Water proofing compound will be measured and paid separately) including finished even and smooth without using extra cement.(for sunken floor ) |
| 116 | M& L for applying evenly a tack coat of industrial bitumen 85/25 grade at the rate of 1.20 kg/Sqm applied on the cleaned surfaces. |
| 117 | M&L for APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/sqm) laid on primed surfaces with 0.40 liter/sqm of bituminious primer, by forced application complete in roof surfaces and on verticle surfaces, all as specified. |
| 118 | Supply only integral water proofing compound |
| 119 | S&F for solid PVC wall lining consisting of 5mm thick single side prelam PVC sheet used instead of plain colour sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing |
| 120 | M&L for 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to the wall to make PVC frame as per specifications and drawing |
| 121 | Taking down DB/main switch of any size and making good disturbed surface of wall/floor complete all as specified. |
| 122 | Taking down carefully sub-main wiring of any description and making good to ther disturbed surfaces to match the existing all as specified and as directed by EIC. |
| 123 | M & L for sub main wiring (concealed) complete with two single core 4 Sqmm FRLS PVC insulated unsheathed stranded copper conductor cable drawn through in and including 20 mm dia rigid non-metallic PVC conduit heavy grade and conduit accessories including 4 Sqmm FRLS PVC insulated unsheated stranded copper earth cable connected to common earth dolly complete and including cutting chasing in walls for concealed wiring using machine cutting and making good the disturbed surface all as specified and directed. Note: 3 run of 4 sqmm cable & one run of PVC conduit shall be measured as single unit |
| 124 | Taking down carefully any type point wiring (light, fans, socket etc) complete including battens and fittings such as switch, ceiling rose, light fittings, regulators, socket, etc. and making good disturbed surface of wall/floor, etc. complete all as specified and as directed. |
| 125 | M & L for point wiring (concealed) on walls and surface on ceiling complete with FRLS PVC insulated unsheathed 1100 Volts grade, conforming to IS-694, 1.5 sq mm (nominal area) multi stranded copper conductor cable drawn though in and including non metallic medium grade rigid PVC conduit heavy grade accessories, ISI marked, 19/20 mm dia including all accessories, concealed in walls by cutting chases using machine and making good the disturbed surface, with and including suitable 1.5 sq mm copper earth continuity wire connected to earth dolly complete for One light point controlled by one switch complete all as specified and as directed. |
| 126 | All as per item No 125 here in before but for One fan point controlled by one switch. |
| 127 | All as per item No 125 here in before but for One exhaust fan point controlled by one switch. |
| 128 | All as per item No 125 here in before but for One bell/ buzzer point controlled by one push switch |
| 129 | All as per item No 125 here in before but for One switch socket outlet modular type 3 pin 6 amp on same board. |
| 130 | All as per item No 125 here in before but for One light point controlled by one two way switches |
| 131 | All as per item No 125 above but 1.5 sq mm cable size and 1.5 sq mm earth continuity wire for one 5 pin socket outlet, 6 amps on Independent board. |
| 132 | All as per item No 125 above but 2.5 sq mm cable size with 2.5 sq mm earth continuity wire for one 5 pin socket outlet, 16 Amps on independent board. |
| 133 | S & F Switch modular type, single pole one way 6 Amps all as specified and as directed. |
| 134 | S & F 0-4 step, one module, modular type electronic regulator for ceiling fan 1200 mm sweep, 240 volts, 100 Watts humfree single pole, all as specified and as directed. |
| 135 | S & F bell push switch, modular type, 6 Amps, 1 module, 250 volts all as specified and as directed . |
| 136 | Supply and fixing calling bell Ding Dong type , AC, single pole one way 230 volts. |
| 137 | S & F socket modular type 6 Amps multistandard 240 volts all as specified and as directed. |
| 138 | S & F switch modular type single pole two way 6 amps 250 volts, all as specified and as directed. |
| 139 | M & L for ceiling rose, surface bakelite, 65 x 50 mm, two to three terminals all as specified and as directed. |
| 140 | S & F switch modular type 16 Amps, 240 volts all as specified and as directed. |
| 141 | S & F socket modular type 16 Amps, 3 pin combine, 2 module,240 volts all as specified and as directed. |
| 142 | S & F Lamp Holder, PVC/Polycarbonate type with cord gird cap all as specified and as directed. |
| 143 | S & F for Modular white cover plate with frame,2 Module |
| 144 | S & F for Modular white cover plate with frame,3 Module |
| 145 | S & F for Modular white cover plate with frame,6 Module |
| 146 | S & F for Modular white cover plate with frame,8 Module |
| 147 | S & F for Modular Metal flux box,2 Module |
| 148 | S & F for Modular Metal flux box,3 Module |
| 149 | S & F for Modular Metal flux box,6 Module |
| 150 | S & F for Modular Metal flux box,8 Module |
| 151 | Supply and Fixing LED luminaire 600x600 mm 35/36 watt ,220V AC recessed type with efficiency PMMA diffuser soft giare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as directed |
| 152 | Supply and fix LED light fitting 2 feet,10 W or nearest higher wattage,230v,suitable for Surface, Wall & Conduit mounting,with extrunded aluminium housing,with integrated LED driver, etc. complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size |
| 153 | S & F sheet metal enclosures for DB's for incorporating MCBs, TPN, 4 way, IP-43 with metal double door with 200 amps rated busbar, 415 volts, as per IS-8623 including taking down the old unserviceable TPN DB, all as specified and as directed. |
| 154 | S & F MCB TPN, 100 Amps, breaking capacity 10 KA 'B' curve confirming to IS/IEC 60898-1 2002,integrated label holder, sliding bottom clamp , IP 20 protected terminal, sliding shutters, 240 volts, 50 HZ including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc. |
| 155 | S & F sheet metal enclosures for SPN DB's with metal double door for incorporating MCBs,IP-43 , 8 way with 200 amps rated busbar, 240 volts, as per IS-8623 all as specified and as directed. |
| 156 | S & F MCB SPN, 40 Amps, breaking capacity 10 KA 'B' curve confirming to IS/IEC 60898-1 2002,integrated label holder, sliding bottom clamp , IP 20 protected terminal, sliding shutters, 240 volts, 50 HZ including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc. |
| 157 | S & F MCB SP 40 Amps, breaking capacity 10 KA 'B' curve confirming to IS/IEC 60898-1 2002,integrated label holder, sliding bottom clamp , IP 20 protected terminal, sliding shutters, 240 volts, 50 HZ including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc. |
| 158 | S & F MCB SP 10-32 Amps, breaking capacity 10 KA 'B' curve confirming to IS/IEC 60898-1 2002,integrated label holder, sliding bottom clamp , IP 20 protected terminal, sliding shutters, 240 volts, 50 HZ including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc. |
| 159 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm Make : Orient / Usha / CG.Note:The rate quoted shall be deemed to be inclusive of cutting of hole in PCC or through brick wall of appropriate dia, making nitche for 250 mm sweep exhaust fan and making good in cement mortar 1:3 or cement concrete 1:2:4 type B0 as required including making good as per existing surface colour matching of wall including 4 Nos of nut & bolts to fix the Exhaust fan complete all as specefied and as directed. |
| 160 | M & L for Earthing complete with galvanised steel plate electrode, 600 x 600 x 6 mm thick, buried directly in ground (earth pit not less than 2.25 mtrs deep below nominal ground level) with top edge of the plate not less than not less than 1.5 metres below nominal ground level connected to earthing lead of 4 mm dia galvanised iron or steel wire all as shown in plate No. 4 of SSR PART 1 of 2009 to the earthing test point all as specified and as directed. Note :- the cost of excavation and earth work PCC pit and RCC cover funnel & watering pipe, wiremesh, charcoal dust and common salt earth lead protection pipe upto 7.5 Rmt shall be deemed included in the unit rate for earthing all as specified and as directed. |
| 161 | M & L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4 mm dia galvanised iron or steel wire all as specified and as directed. |
| 162 | Taking down fan,dismantling blades and removing fan and blades including repair,servicing, rewinding and replacement of spare parts including painting of ceiling fan complete complete all as specefied and as dirceted. |
| 163 | S & F sheet metal box of indoor type CRCA sheet 2mm thick power coted of sze 700mm x 700mm x 300mm for accomodaing of single phase meters 4 Nos and VTPN DB 1 No including taking down the old unserviceable metal box, all as specified and as directed. |
| 164 | S & F LED Bulb 9 Watt all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 20, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 09, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayJul 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender