|
| 1 | Dismantling old fencing wire mesh/chain link fencing, any description, any type complete all as specified and as directed. |
| 2 | Dismantling fencing posts or struts (wood, steel or R.C.C.) any section complete all as specified and as directed. |
| 3 | Excavation in post holes in any type of soil, each not exceeding 0.5 Cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance not exceeding 50 m and making good surface complete all as specified and as directed. |
| 4 | Excavation in trenches, not exc 1.5m wide and not exc 1.5 m in depth, in any type of soil for foundation, laying pipes for drains or manholes etc, n exc. 10 Sqm on plan and n.exc 1.5 m in depth and getting out including trimming sides and forming bottom surfaces to required level/slope etc complete all as specified and as directed. |
| 5 | Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm thick with soils all complete all as specified and as directed. |
| 6 | Removing excavated soil to distance exc 250m and not exc 500m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and as directed. |
| 7 | M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregates) as in foundation, filling and mass concrete etc. including demolition of existing cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed. |
| 8 | M&L for PCC, 1:2:4, type B1 (using 20 mm graded stone aggregates) as in lintels upto 1.50m clear span, cills, steps, seismic and other similar bands, plinth courses, copings and the like including watering, slightly rounded or chamfered angles and throating complete including demolition of existing cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed. |
| 9 | M&L for RCC 1:2:4 (nominal mix) type B-1 using 20 mm graded stone aggregate as in foundations, beams, plinth beams, base of columns etc including demolition of existing RCC of any description complete all as specified and as directed. |
| 10 | M&L for RCC 1:2:4 (nominal mix) type B-1 using 20 mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span,etc including demolition of existing RCC of any description complete all as specified and as directed. |
| 11 | M&L for RCC 1:2:4 (nominal mix) type B-1 using 20 mm graded stone aggregate as in Columns, pillars, piers, posts and struts etc including demolition of existing RCC of any description complete all as specified and as directed. |
| 12 | M&L Providing precast cement concrete type B1 1:2:4 using 12.5 mm stone aggregate in cills, lintels, quoin blocks (for use with masonry), copings, kneelers, apex stones, bed plates, pintle blocks, anchorage blocks, with plain fair faces, including chamfers, weatherings throating etc. and setting in CM 1:4 complete with joints to match including demolition of existing precast cement concrete of any description complete all as specified and as directed. |
| 13 | M&L for 35mm thick precast cement concrete louvers and jallies including mouldings in precast cement concrete 1:2:4 type B-0 using 12.50mm graded stone aggregate and fixed in cement mortar 1:4 including dismantling old precast louvers and jallies complete all as specified and as directed. |
| 14 | M&L for brickwork with old size fly ash bricks straight or curved on plan with mean radius exc 6m built in CM 1:6 including demolition of brick/ block/ stone masonry built in cement mortar complete all as specified and directed. |
| 15 | Use and waste form work to sides of concrete in foundations, footings, bases of columns, side and soffits of plinth beam and simillar work for rough finished surfaces of concrete complete all as specified and as directed. |
| 16 | Use and waste of formwork to sides and soffits of beams for rough finished surfaces of concrete all as specified and as directed. |
| 17 | Use & waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces of concrete complete all as specified and as directed. |
| 18 | S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 including dismantling of existing wrought iron or mild steel work of any description complete all as specified and directed. |
| 19 | S&F 1.25 mm thick mild steel plain black sheet as in hearths, covering to door shutters, coverings to door chowkats (frames), funnels etc cut to size, edges beaded if directed holespunched, including rounded headed screw, clout nails or rivts and fixed to steel members etc with plain 40mm lap joints or welded/riveted seams including bending, turning up, mitred angles,stopped ends, outlets etc as required complete all as specified and as directed. |
| 20 | M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 21 | M&L for mild steel TMT bars 5 mm dia and over upto and including 10mm dia, in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 22 | M&L for mild steel framed work conforming to Fe 410 -W (GdeE- 250) qualityA, as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing including dismantling of existing wrought iron or mild steel work of any description complete all as specified and directed. |
| 23 | S&F mild steel angle/flat iron as in fencing posts/struts for securing barbed/chain link fencing of any description including drilling holes, notching for wire etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or rivetting and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed. |
| 24 | S&F in repairs, galvanised, 2 strand, steel barbed wire, 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails restraining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. com plete all as specified and as directed |
| 25 | Restraining, resecuring including making good staples etc for repair of galvanised 2 strand, steel barbed wire complete all as specified and as directed. |
| 26 | Supply only mild steel galvanised chain link fencing, made out of GI wire, any size or type, complete all as specified and directed.Note :- (i) Dia and size of mesh shall be as decided by Engineer -in-Charge. (ii) Payment shall be allowed only after ascertaining weight of chain link fencing as per actual at site by the BOO ordered by GE.(iii) Engineer - in - charge shall ensure that the weight shall be not more than 3 Kg/ Sqm before execution. |
| 27 | Fixing only chain link fencing any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and as directed. |
| 28 | S&F mild steel in round or square bars as in line bars for fixing chain link fencing including cutting to length, bent to shape required, hooking ends complete all as specified and as directed. |
| 29 | M&L for machine made, mild steel bolts, 10 mm dia shank with hexagonal or square head one end and screwed the other or screwed both end, each screwed end to be fitted with, washers and one hexagonal or square nut, length length of bolt exc 5cm but n exc 10cm complete all as specified and as directed. |
| 30 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing rubbish off the premises complete all as specified and as directed. |
| 31 | M&L for precast cement concrete coloured chequered tiles with glossy finish of size 25cm x 25cm x 25mm thick/30cm x 30cm x 25mm thick, machine pressed with grey cement and pigment, set, jointed and pointed in neat cement slurry over and including 20mm thick screed bed or bedding layer in cement mortar 1:6 and pointed in coloured cement to match the colour of tiles complete all as specified and as directed. |
| 32 | Dismantling of stone slab and tiles laid bedded and pointed in any mortar description or thickness in floors, apron etc complete all as specified and as directed. |
| 33 | M&L for 75mm thick plain cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base of floors and pavings including demolition of existing cement concrete of any description complete all as specified and as directed. |
| 34 | M&L for 60mm thick, factory made, chamfered edge, cement concrete interlocking paver blocks (glossy/ rubber matt finish) of M-35 grade with approved colour, design & pattern of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as required size and pattern, finishing and sweeping extra sand; etc complete all as specified and as directed.Note : Size, shape, pattern and shade shall be as approved by Engineer-in-Charge. |
| 35 | M&L for 45 to 50mm thick Prestressed reinforced cement concrete solid slabs finished fair on both sides in Prestressed cement concrete 1:2:4 type B-0 (12.5mm graded stone aggregate) (with interlocking joints as directed) including mouldings and fixed as compound wall in grooves of Prestressed posts as per approved design and pattern and set in cement mortar 1:4 complete all as specified and as directed. Note : (a) The cost of reinforcement and form work shall deemed to be included in rate quoted.(b) Surface area of slabs excluding embedded portion in grooves shall be measured for payment. (c) Prestressed concrete posts shall be measured and paid separately. |
| 36 | M&L for prestressed reinforced cement concrete solid posts with fair faces in precast cement concrete 1:2:4 type B-0 (12.5mm graded stone aggregate) (with grooves for interlocking of precast slabs as directed) including mouldings and fixed in columns, posts, boundary pillars with and including grooves to locking of precast RCC precast wall panels, set in cement mortar 1:4,including arrengment for fixing of barbered wire/concertina coil etc complete all as specified and as directed.Notes : (a) The cost of reinforcement and form work shall deemed to be included in rate quoted.(b) Precast/prestressed slabs for wall shall be measured and paid separately under respective item. |
| 37 | M&L at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed. |
| 38 | Taking down cement plaster on walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and as directed. |
| 39 | M&L for rendering 15 mm thick on other than fair faces of brick work /concrete surfaces in cement mortar 1:4, finished even and fair without using extra cement complete all as specified and as directed. |
| 40 | M&L for preparation of new plastered or unplastered surfaces and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and as directed. |
| 41 | M&L for preparation of old plastered or unplastered surfaces of walls including cornices and applying one coat of cement base paint (white or tinted) complete all as directed and as specified. |
| 42 | M&L for preparation of new steel surfaces of any description exc 10cm in width or grith and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 43 | M&L for preparation of new steel surfaces of any description n.exc 10 cm in width or grith and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and as directed. |
| 44 | M&L for machine cut cudappah stone slab 20-25mm thick for cooking platform, verticals of wash basins and sinks etc including cutting chases in wall and fixing the slab in cement mortar including rubbing and polishing complete all as specified and as directed. |
| 45 | M&L 18 to 20mm thick pre-polished granite stone slab of approved shade and colour as in table top, top of WHB, kitchen slab/platform, gate pillars, cills etc or on vertical surfaces including vertical projection, urinal partition, including full round moulding the outer edge, laid over and including screed bed 20mm thick in cement mortar 1:4 jointing, pointing in white cement 1:2 using marble dust with admixture or pigment to match the shade of granite and rubbing, polishing to achieve mirror finish complete all as specified and as directed.Note : Colour and shade shall be as approved by GE. |
| 46 | M&L for machine cut Kota stone flooring 20 to 22 mm thick (size of kota stone slab 22\\"x22\\") laid over and including 20 mm thick bedding layer of cement mortar 1:6, jointed with grey cement slurry mixed with pigments to match the shade of slab including cutting, rubbing and mirror polishing including removing dust complete all as specified and as directed. |
| 47 | All as per item No 46.00 here in before but 18-20 mm thick as in risers to steps and skirting laid over and including backing coat of 10mm thick in cement mortar 1:3 complete all as specified and as directed.Note : Risers provided to steps shall be in one piece. |
| 48 | M&L for non skid coloured ceramic mat finished tiles 7-8mm thick (square or rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm (600X600 mm) in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified & directed.Note: Color and shade shall be as approved by Engineer-in-charge |
| 49 | M&L for non skid coloured ceramic 7-8mm thick (square or rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified & directed.Note: Color and shade shall be as approved by Engineer-in-charge |
| 50 | M&L for glazed ceramic tiles of size 450mm x 350mm x 7 mm thick on vertical surfaces, laid over and including 10 mm thick rendering in cement mortar 1:4, set & jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles complete all as specified and as directed. |
| 51 | S&F Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as directed. |
| 52 | S & F stainless steel grating with square frame (grating thickness 1mm and frame thickness 1.5mm) of size 125mm (minimum) with waste hole complete all as directed. |
| 53 | S&F in repairs rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), 500 litres capacity, tripple layered, hoisted and fixed in position including 20 mm dia ball valve PTMT high pressure float valve with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting complete all as specified and as directed. |
| 54 | S&F in repairs 20 mm float valves high pressure PTMT with epoxy coated aluminium rod & high density plastic ball screwed for 20 mm bore iron pipe complete all as specified and directed. |
| 55 | S&F 16 mm outer dia of CPVC pipes SDR 11 & brass CPVC SDR 11 fittings on walls/ceiling or laying in floors complete including taking down old GI pipe 15mm bore all as specified. |
| 56 | S&F 20 mm outer dia of CPVC pipes SDR 11 & brass CPVC SDR 11 fittings on walls/ceiling or laying in floors complete including taking down old GI pipe 20mm bore all as specified. |
| 57 | S&F in repairs 20mm dia gun metal globe or gate valve, wheel head cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union, ISI marked complete all as specified & as directed |
| 58 | S&F in repair Vitreous China, Squatting pan Orissa pattern size 580 x 440mm, white with integral foot rests (excluding flushing cistern and flush pipe) with Vitreous China ‘P’ or ‘S’ trap, front or back inlet including connection to trap and to flushing pipe, anti syphonage pipe, including PCC (1:2:4) type B-1 for fixing of WC and making good the floor to match the existing complete all as specified and as directed.Make: Cat No. S3010102 of CERA or equivalent model of makes specified |
| 59 | S&F in repairs, vitreous china wash down water closet (pedestal pattern) white, including connection to drain (or outgoing pipe) and flushing pipe, anti syphonage pipe, trap set and including white or black seat cover for pedestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws, etc. complete all as specified and as directed.Make: Cat No. S1053102 of CERA or equivalent model of makes specified. |
| 60 | S&F in repairs, Health faucet (ABS Body) suitable for 15 mm dia pipe with 1 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.Make: Cat No. F8030111AB of CERA or equivalent model of makes specified. |
| 61 | S&F in repairs 10 ltr capacity PVC valve-less, syphonic action type flushing cistern, low level, white with inlet ball valve and handle including brackets complete all as specified and as directed.Make: Cat No. B1010110 of CERA or equivalent model of makes specified. |
| 62 | S&F vitreous china wash hand basin, white flat back of size 550 mm x 400 mm including brackets, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts and PVC waste pipe15mm dia, PVC connection pipe 450mm long complete all as specified and as directed.Make: Cat No. S2040141 of CERA or equivalent model of makes specified. |
| 63 | S&F in repairs, 15 mm bore pillar taps, cast copper alloy with capstan heads, fancy type, chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed.Make: Cat No. F1015101 of CERA or equivalent model of makes specified. |
| 64 | S&F in repairs, bib tap 15mm dia, with wall flange and aerator screwed down for iron pipe or for brass ferrule complete all as specified and as directed.Make: Cat No. F1015151 of CERA or equivalent model of makes specified. |
| 65 | S & F in repairs, stop/ angle valves, 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.Make: Cat No. F1015201 of CERA or equivalent model of makes specified. |
| 66 | S & F in repairs, PVC connections, 15 mm size with brass check nuts of length 600 mm complete all as specified and as directed. |
| 67 | S&F in repair Soap dish, chromium plated, fixed to plugs with chromium plated screws complete all as specified & directed. |
| 68 | S&F in repairs, 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated screws and cup washers complete all as specified and as directed. |
| 69 | S&F in repairs wall mixer for mixing hot and cold water and bend for connecting to shower, 15 mm bore screwed for iron pipe and fixed complete all as specified and as directed.Make: Cat No. F1015401 of CERA or equivalent model of makes specified. |
| 70 | S&F in repair overhead shower rose 125mm size with 200mm long shower arm and wall flange complete all as specified & directed by Engr-in-charge.Make: Cat No. F7020111AB of CERA or equivalent model of makes specified. |
| 71 | S&F in repair sheet glass assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets guard and railing 60cm long complete all as specified and directed by Engr-in-Charge |
| 72 | S&F in repairs towel rail 60 cm long between flanges complete all as specified and as directed.Make: Cat No. F5015103CH of CERA or equivalent model of makes specified. |
| 73 | S&F in repairs, stainless steel sink with drain board made of 1mm thick sheet for kitchen with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 350mm x 185 mm including CP waste coupling complete all as specified and as directed.Make: Cat No. SBSD 05 (RR) of JAYNA or Elegance Small of Nirali or equivalent model of makes specified. |
| 74 | S&F in repairs, 32/ 40 mm bore PVC flexible outlet pipes for wash basin/ sink/ urinal fixed complete all as specified and as directed. |
| 75 | Taking down chowkhats or frames with shutter (without taking out shutter from the frame), area n.exc 1.5 sqm each all as specified and as directed. |
| 76 | S & F powder coated aluminum windows, three track, made out of aluminium sections including all necessary fittings, 5mm thick sheet glass, stainless steel wire cloth 0.36 nominal dia of wire and average width of aperture 1.4mm, rubber/ neoprene beading, locking arrangements all as specified and as directed and comprising of following sections :- (a) Window frame: (i) Bottom-Section 20671 (Wt not less than 0.699 Kg/m) (ii) Top & Side - 20672 (Wt not less than 0.594 Kg/m)(b) Shutter: (i) Vertical (end)- 20669 (Wt not less than 0.548 Kg/m) (ii) Vertical (lock) - 20689 (Wt not less than 0.481 Kg/m) (iii) Bottom - 20718 (Wt not less than 0.263 Kg/m) (iv) Top - 20668 (Wt not less than 0.377 Kg/m)Note : Shade shall be as approved by Engineer-in-Charge. |
| 77 | S&F uPVC ventilator of size 600 x 900 mm including glass louvers, S/S wiremesh, complete all as per TD No CEPZ/2019/TD/01 sheet 1/2 & 2/2 complete all as specified and as directed. |
| 78 | S&F in repairs 25mm dia mild steel chromium plated Curtain rails with end brackets , stops , rollers etc all as specified and directed. |
| 79 | M & L for Framed work such as grills, gratings, etc., framed guard bars and similar work with ends of bars shoulders and / or riveted, or forged into spikes; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete including dismantling of old iron, mild steel work of any description all as specified and as directed. |
| 80 | S&F in repairs, 75 mm dia PVC(SWR) nahani/floor trap with grating including jointing to waste pipe with solvent cement complete all as specified and as directed. . |
| 81 | S&F in repairs, 110mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed. |
| 82 | S&F in repairs, 110mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls all as specified and as directed. |
| 83 | S&F in repairs, 110mm bore PVC (SWR) branch piece, double (double Y) equal or unequal with oval access door all as specified and as directed. |
| 84 | S&F in repairs, 110 mm dia PVC (SWR) bends of any radius with oval access door complete all as specified and as directed |
| 85 | S&F in repairs, 110 mm dia PVC (SWR) bends of any radius complete all as specified and as directed |
| 86 | S&F in repairs, 75mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed. |
| 87 | S&F in repairs, 75mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls all as specified and as directed. |
| 88 | S&F in repairs, 75mm bore PVC (SWR) branch piece, single (single Y) equal or unequal with oval access door all as specified and as directed. |
| 89 | S&F in repairs, 75 mm dia PVC (SWR) bends of any radius with oval access door complete all as specified and as directed |
| 90 | S&F in repairs, 75 mm dia PVC (SWR) bends of any radius complete all as specified and as directed Please Enable Macros to View BoQ information |
