Name of Work:- PROVN OF 05 NOS HIGH MAST LIGHT POLE WITH LUMINARIES & UG CABLE AT BENGDUBI MIL STN UNDER GE BENGDUBI.
Sl. No.
Item Description
1
Supply , erection, Installation and commissioning of 16 Meter high mast pole suitable for 8 Nos LED flood light, symmetrical (Material construction of high mast sheet shall be of BSEN 10025/IS 5986 Gr Fe 510) High mast pole shall be in two section,with plate thickness of top section as 3mm and bottom section as 4mm hot dip galvanised and suitable for wind velocity as per IS 875 part 3, Three point suspension system. It shall also include foudation as per manufacuture & drawing & scope of work shall also be deemed to include the following:-(a) Galvanised Lantern carriage arranegment suitable for 8 luminaires symmetrically & lts control gear boxes and lightning finial and with 03 point suspension system.(b) Double drum winch motor and manual method of operation tested load drum 500 kgs.(c) Stainless steel wire rope 6mm dia 7/19 construction conforming to AISI-316 grade.(d) The mast shall have an integral power tool 1.5 HP 1400 RPM single speed Reversible 415 Volt, installed inside the base compartment for its operation.(e) 01 No LEd type Aviation obstruction light.(f) Service Wiring feeder to flood light with multistranded copper conductor cable with double run for one standby cable. (g) Design costing of suitable RCC Foundation with Concrete grade for high mast considering SBC of soil as 10 T/sqm (after cutting of concrete & bituminous road and incl bolts manufactured from special steel along with nuts washers, anchor plates and templates etc and including PCC (1:2:4) for panel grounting, complete all as per manufacuturers instructions subject to approval of the GE.(j) Supply, installing, testing and commissioning, factorymade tested, LT feeder pillar box outdoor type (CPRI approved). The panel shall be dust and vermin proof , IP 65 class protection and made out of 3.15mm CRCA MS sheet and 40x40x4mm thick angle iron frame work. powder coated finish over one coat of red oxide primer outside and two coats of red oxide primer on inside double door openable type, with aprons for cable entry, internal wiring with PVC insulated stranded copper conductor, FRLSH cables, IS-694 marked of adequate size but not less than 10 Sqmm . 2 Nos danger notice plate made of 1.6mm thick mild steel sheet, vitreous enamelled white of size 25 x 20cm with appropriate size nuts, bolts and washers etc indicating the voltage and danger in Hindi and english complete all as specified and directed, The following items/accessories shall also be deemed to be incuded and accomdated in the above panel:-(i) Stag type 4 way terminal (I/P) 63 Amps- 1 No (PCb 150 ACBC). (ii) MCCB, 63 Amps., 4 Pole, 25KA, 415V-1 no. (iii) Contactor 3 pole,63 Amps -01 Nos. (iv) Toggle Switch 6Amps-1 No. (v) Timer (analogue). (vi) Stag type, 4way terminal (O/P) 63A -1 No(PCB 150ACBC). (vii) Over load relay 2/3.5A- 1 No. (viii) F.contactor 9A- 1No. (ix) R. contactor 9A- 1 No. (x) Motor terminal 32 Amps-1 No(xi) Push switch terminal -1No. (xii) Push switch (F/R) STD-1 No. Please Enable Macros to View BoQ information
2
Supply , erection, Installation and commissioning of 16 Meter high mast pole suitable for 8 Nos LED flood light, symmetrical (Material construction of high mast sheet shall be of BSEN 10025/IS 5986 Gr Fe 510) High mast pole shall be in two section,with plate thickness of top section as 3mm and bottom section as 4mm hot dip galvanised and suitable for wind velocity as per IS 875 part 3, Three point suspension system. It shall also include foudation as per manufacuture & drawing & scope of work shall also be deemed to include the following:-(a) Galvanised Lantern carriage arranegment suitable for 8 luminaires symmetrically & lts control gear boxes and lightning finial and with 03 point suspension system.(b) Double drum winch motor and manual method of operation tested load drum 500 kgs.(c) Stainless steel wire rope 6mm dia 7/19 construction conforming to AISI-316 grade.(d) The mast shall have an integral power tool 1.5 HP 1400 RPM single speed Reversible 415 Volt, installed inside the base compartment for its operation.(e) 01 No LEd type Aviation obstruction light.(f) Service Wiring feeder to flood light with multistranded copper conductor cable with double run for one standby cable. (g) Design costing of suitable RCC Foundation with Concrete grade for high mast considering SBC of soil as 10 T/sqm (after cutting of concrete & bituminous road and incl bolts manufactured from special steel along with nuts washers, anchor plates and templates etc and including PCC (1:2:4) for panel grounting, complete all as per manufacuturers instructions subject to approval of the GE.(j) Supply, installing, testing and commissioning, factorymade tested, LT feeder pillar box outdoor type (CPRI approved). The panel shall be dust and vermin proof , IP 65 class protection and made out of 3.15mm CRCA MS sheet and 40x40x4mm thick angle iron frame work. powder coated finish over one coat of red oxide primer outside and two coats of red oxide primer on inside double door openable type, with aprons for cable entry, internal wiring with PVC insulated stranded copper conductor, FRLSH cables, IS-694 marked of adequate size but not less than 10 Sqmm . 2 Nos danger notice plate made of 1.6mm thick mild steel sheet, vitreous enamelled white of size 25 x 20cm with appropriate size nuts, bolts and washers etc indicating the voltage and danger in Hindi and english complete all as specified and directed, The following items/accessories shall also be deemed to be incuded and accomdated in the above panel:-(i) Stag type 4 way terminal (I/P) 63 Amps- 1 No (PCb 150 ACBC). (ii) MCCB, 63 Amps., 4 Pole, 25KA, 415V-1 no. (iii) Contactor 3 pole,63 Amps -01 Nos. (iv) Toggle Switch 6Amps-1 No. (v) Timer (analogue). (vi) Stag type, 4way terminal (O/P) 63A -1 No(PCB 150ACBC). (vii) Over load relay 2/3.5A- 1 No. (viii) F.contactor 9A- 1No. (ix) R. contactor 9A- 1 No. (x) Motor terminal 32 Amps-1 No(xi) Push switch terminal -1No. (xii) Push switch (F/R) STD-1 No. Please Enable Macros to View BoQ information
We takes all possible care for accurate & authentic tender information, however Users
are requested to refer Original source of Tender Notice / Tender Document published by
Tender Issuing Agency before taking any call regarding this tender.
