|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.-All kinds of soil |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. All kinds of soil |
| 3 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level |
| 5 | 1:3:6 ( 1 Cement: 3 fine sand : 6 graded well burnt brick aggregate 40 mm nominal size) |
| 6 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement- All work upto plinth level i) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size) |
| 7 | Providing structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as required. |
| 8 | Supply & installation of pre-painted Galvalume sheets for roofing/cladding (size, shape and pitch of corrugation as approved by Engineer-in-charge) in 550mpa steel grade, made out of Cold Rolled Steel coated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to ASTMA792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality Polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-incharge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required and as per direction of Engineer-in-charge. |
| 9 | 11.22.4) 0.60mm thickness |
| 10 | First class brick work in foundation and plinthincluding cost of all materials as required complete:- i) In cement mortar 1:4 (1 cement : 4 fine sand) |
| 11 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sqm and under including cutting the patch in proper shape and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground with all leads and lifts including finishing even and smooth and curing complete as per direction of the Engineer in charge:- a) With cement mortar 1:4 ( 1 cement : 4 fine sand ) |
| 12 | 15 mm cement plaster on the rough side of single or hal brick wall of mix: a) In cement mortar 1:4 (1 cement: 4 fine sand) |
| 13 | 12 mm cement plaster of mix i) In cement motar 1:4 (1 cement : 4 fine sand) |
| 14 | Neat cement punning. |
| 15 | Supply & installation of pre-painted Galvalume sheets roofing accessories in 550mpa steel steel grade, made out of Cold rolled steel coated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to AASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side etc. complete as per direction of Engineer-in-charge. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. The sheetshall be fixed using self drilling /self tapping screws with EPDM washers complete for Ridges/Valley/Gutter/Flashing of width 610mm:. |
| 16 | 11.23.4) 0.60mm thickness |
| 17 | Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. complete as required:a) In grating, frames, guard bar, railing, brackets, gates and similar works, all complete. |
| 18 | Applying priming coat [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : a)With ready mixed red oxide zinc chromate primer ofapproved brand and manufacture on steel work (second coat ) |
| 19 | Aluminium Composite Panels of 3mm total thickness with Top coil – 0.25mm AA3003 Grade manufactured as per IS-737 1986, FR Grade Class B1 with 2.50mm Mineral Core with minimum 70-72% Inorganic content (Aluminium Hydroxide and Magnesium Hydroxide) 28- 30% Organic content (LDPE) conforming to ASTM E-119- 16,18 and EN 13501 - 1 class B1 and Bottom coil – 0.50mm AA3003 Grade manufactured as per IS-737 1986 with minimum 25 microns lead free PVDF Coating conforming to AAMA2605 on top coil and Service coating on Back Coil (4 - 6 microns) having minimum panel weight of 5.25 Kg/m2. |
| 20 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete |
| 21 | Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :- |
| 22 | 16.3.2 With float glass panes of 5.5 mm thickness ( weight not less than 13.75 kg / sqm ) |
| 23 | Finishing walls with premium acrylic smooth exterior paint with Silicon additives of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : a) New work ( two or more coats applied @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 24 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]a)Two or more coats on new work |
| 25 | Providing and fixing aluminium work for doors,windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge. (Glazing and paneling and dash fasteners to be paid for separately) :- |
| 26 | 16.1.1.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 27 | For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):- |
| 28 | 16.1.2.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 29 | Providing and making bamboo make ladder around the Steel/RCC Over Head Tank, up to the top of the steel/RCC tank Reservior, making bamboo staging covering all the prephere and platform by mulli bamboo at bracing level whenever required, gradually with progress of work upwards, covering the entire plan area and around the Steel/RCC Overhead tank to create passage for worker and transshipment of materials at various level including dismantling and disposal of the staging after completion of repair job, as directed by the Engineer-in-charge. (Sufficient propping and strutting of barack bamboo at least 80 mm dia and platform at bracing levels and rectangular steel/RCC OHT may be of muli bamboo, exposed vertical sides of the platform may be covered by the nylon or jute net /Nail & G.I. wire to avoid the ocurrence of workers fall during work. Staging thus erected to be maintained through periodical maintenance through out the entire period at the risk and cost of the agency). (For big size steeltank 13.20m x 13.20m ) & after completion of big size steel/RCC tank for Small Size Steel tank 13.20 m x 8.40m) |
| 30 | Installation of 8 nos. CC Camera with HDD 4TB ,SMPS 20 AMP, 22 Inch LED Monitor, DVR etc. of approved brand and manufacturer complete as per direction of the Engineer-in-Charge. |
| 31 | Providing and installation of ACP sign board with retro reflective sticker (Cautionery / mendatory / informatory) to be fixed on existing structures like gate, boundary wall etc. as per direcion of the Engineer-in-charge. |
| 32 | Providing and installation of Vinyl sun board (Cautionery / mendatory / informatory) to be fixed on existing structures like gate, boundary wall etc. as per direcion of the Engineer-in-charge. |
| 33 | Providing and installation of Glow Sign board (Cautionery / mendatory / informatory) to be fixed on existing structures like gate, boundary wall etc. as per direcion of the Engineer-in-charge. |
| 34 | Providing and erecting direction and placeidentification retro-reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide MoRD technical specification Clause 1701.2.3 fixed over aluminium sheeting, 2 mm thick with area exceding 0.9 sqm supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm 2 Nos. firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete (using jhama brick aggregate) 450 mm x 450 mm x 600 mm, 600 mm bellow ground level as per approved drawings and MoRD Technical Specification Clause 1701. |
| 35 | Lettering with black Japan paint of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer]. Please Enable Macros to View BoQ information |
