Tender For Special Repairs (B/R) To Senior Sailors Married Acommodation Mackeral - V/8, V/10(Bldg No P-40) And Mackeral -Vi/3, Vi/4, Vi/5, Vi/6 (Bldg No P-41) At installation Pallava Under Ge Navy Chennai
Tender Value
44.50 Lakhs
Estimated cost
Bid Submission
15 Jul 2026
2 days left
EMD
89000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chennai → Tamil Nadu
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repairs (B/R) To Senior Sailors Married Acommodation Mackeral - V/8, V/10(Bldg No P-40) And Mackeral -Vi/3, Vi/4, Vi/5, Vi/6 (Bldg No P-41) At installation Pallava Under Ge Navy Chennai
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 08-Jul-2026 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 15-Jul-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Demolition cement concrete (unreinforced) in ground floors and paving n.exc 15cm thick (below & above ground level) |
| 2 | Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided including padding concrete on roof all as specified and directed. |
| 3 | M&L for applying epoxy water proofing treatment for sunken floor over and including rendering 15mm thick on fair faces of brick work or concrete surfaces with cement plaster 1:3 with WPC @ 2% by weight of cement including finishing even and smooth without using extra cement. (Note : Water proofing compound will be measured and paid separately) |
| 4 | M&L for PCC 1:5:10 type E-2 (using 40mm graded stone aggregate) as in mass concrete as in sunken floor etc finished fair complete all as directed by Engr-in-Charge. |
| 5 | M&L for 25mm thick PCC 1:2:4 type B0 (12.5mm graded stone aggregate) as in screed bed over sub base finished fair complete all as directed by Engr-in-Charge. |
| 6 | Dismantling of wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises including removing of all the debris to a distance n exc 2 km out side the base at the disposal of the contractor. |
| 7 | M&L for screed bed or bedding layer of cement mortar 1:6, 15 mm thick for laying floor finishes complete all as directed by Engr-in-Charge. |
| 8 | M&L for glazed ceramic coloured tiles 350 x 250mm x7mm/450 X 350 X 7mm thick as in skirting/dados set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick backing coat on fair faces of brick work/concrete in CM 1:4 to receive tiles as in dado. |
| 9 | M&L for Coloured non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 18 sqm but not exceeding 0.38 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match complete all as specified and directed by Engineer-in-Charge. |
| 10 | All as per item No 9 here in before but Coloured non skid ceramic tiles 7 to 8 mm thick in skirtings. |
| 11 | M & L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) joint free tiles, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match |
| 12 | Cutting grooves in brick/concrete wall, 75mm wide and 65mm deep and shaping horizontal face of grooves with cement mortar 1:3`complete all as specified and as directed. |
| 13 | Removing of debries any description obtained from demolition beyond the lead included in the rates including loading unloading to a distance exceeding 1.5Km and not exceeding 2.00 KM out side defence land. |
| 14 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc all as specified and as directed by the Engr-in -charge. |
| 15 | M&L for applying cement slurry @3Kg/Sqm provided over cleaned roof surface |
| 16 | M&L PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) as in padding concrete to maintain required slope including coving to junctions of parapet and roofs. . |
| 17 | M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces with cement plaster 1:3 with WPC @ 2% by weight of cement including finished even and smooth without using extra cement. (Note : Water proofing compound will be measured and paid separately) |
| 18 | M & L Preparation of new plastered surface & applying bituminous primer @ 0.41Kg/Sqm all as specified and directed. |
| 19 | M&L for APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/sqm) over a coat of hot blown bitumen 85/25 grade @ 1.20 Kg/Sqm over primed surfaces by forced application complete in roof surfaces and on verticle surfaces, all as specified. |
| 20 | M & L for Cement concrete tiles 25cm x 25cm x 22mm thick machine pressed, set jointed and pointed in neat cement slurry in floors with grey cement and pigments over a coat of 20mm thick screed bed in CM 1:6 complete. |
| 21 | Supply only integral water proofing compound. |
| 22 | Taking down chowkat or frame with shutters (without taking off shutters from the frames) not exc 1.5 sqm each. |
| 23 | Taking down Chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each(without taking off shutters from the frames) |
| 24 | Taking down shutters of any description exc 1 sqm and n.exe 2 Sqm . |
| 25 | Supply & fix Solid PVC Door Frame of size 50mm x 47mm made out of 5mm, but wood grain printed PVC sheet used instead of Plain colour PVC sheet & edge reinforced with M.S. Square tube will be painted to match with printed sheet Complete all as specified. |
| 26 | Supply & Fix Factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site but 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face as per specification. |
| 27 | S & F Second class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints. |
| 28 | S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides including 6mm thick teak wood lipping all as specified. |
| 29 | M&L 35mm thick 2nd class hard wood plain framed panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces.The size of rail and stile as per IS:1003 (Part1),kiln seasoned and chemically pressure treated, all as specified and directed. |
| 30 | S & F 30 mm thick second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars) chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in SSR Pt I Section 8, clause 8.24 (a) |
| 31 | M & L Cup boards stuttters made with 18/19 mm thick prelaminated particle board with decorative lamination on one side and other side balancing white lamination medium density, exterior grade, including 6 mm teak wood lipping all as directed. |
| 32 | S & F 6mm thick marine plywood fixed with nails/Screws to frame works as in cabinets cupboards with SS angle cleats etc complete all as specified and as directed |
| 33 | S & F white laminates of 0.9mm thick surface finish matte or glossy colour and pattern as approved adhesive complete all as specified and directed . |
| 34 | S & F decorative coloured laminates of 1.5mm thick glossy finish, colour and pattern as approved adhesive complete all as specified and directed |
| 35 | S&F stainless steel accessories grade 202 (make:- V-Boss/ Olive -silver / Godrej accessories) Cutlery basket of size 19''x20''x4'' complete all as specified and as directed. |
| 36 | All as per item No.35 above but Cup and saucer basket of size 19''x20''x6'' |
| 37 | All as per item No.35 above but Plain basket of size 19''x20''x8'' |
| 38 | S&F CP decorative type Brass handles, cast type, polished bright handles 75 mm long fixed to plywood or frame complete all as specified and directed |
| 39 | Supply and fix for telescopic channel of size 450mm to 560mm of load per 45 kg/cmsq complete all as specified and directed |
| 40 | S&F 80mm Auto SS hinges of crank 0 degree to 90degree, fixed with screws to plywood or frame work as per sample approved by EIC complete all as specified and directed |
| 41 | S&F sheet glass ordinary quality 4mm thick, in squares exc. 0.5 sqm each pane complete all as specified. |
| 42 | S&F sheet glass ordinary quality 4mm thick, in squares n exc. 0.5 sqm each pane complete all as specified and directed by Engineer in Charge |
| 43 | S & F in repairs Aluminium alloy wire cloth, 0.45 mm dia of wire and average width of aperture 1.40 mm and fixed with stainless wire staples |
| 44 | S & F Aluminium alloy wire cloth, 0.45 mm dia of wire and average width of aperture 1.40 mm and fixed with stainless wire staples |
| 45 | S&F 100mm hinges extruded aluminium alloy with galvanised mild steel pin anodized and fixed type C-21 Complete all as specified and directed by Engineer-in-Charge. |
| 46 | S&F 150 mm size,Extruded aluminium alloy handles, fabricated type, anodised |
| 47 | S&F 200 mm size aluminium anodised, barrel tower bolts of extruded section and fixed. |
| 48 | S&F 300mm long Aluminium, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded section all as specified. |
| 49 | S&F magic eye15mm dia steel body suitable for 35 to 40 mm thick doors with all necessary fittings all as specified and direcetd by Engr-in-Charge |
| 50 | S & F Mild steel Angles, bars, flats etc., as in supports for stiffening of fencing, wall ties, hold fasts, clamps, plain angle cleats for securing purlins and similar small articles confirming to Fe 410-O 0r Fe 310-O |
| 51 | M&L Providing PCC Type B1, 1:2:4 (20mm graded stone aggregate) as in hold fast fixing etc |
| 52 | S&F in repair aluminium anodised tubular curtain rail 20mm dia |
| 53 | S&F in repairs aluminium anodised, brackets (designer pattern) for curtain rods |
| 54 | S&F in repair aluminium anodised tubular rail 20mm dia D type 60cm long between flanges including per pair brackets for each towel rail. |
| 55 | S & F 150 mm door stopper of alumiminium alloy body, with rubber bush |
| 56 | S&F in repair aluminium hat pegs solid body 125mm to 175mm long. |
| 57 | S&F in repair vitreous china squating pan \\"Orisa\\" patern size 580 x 440mm white with 'P' or 'S' trap front or back inlet with integral foot rest (excluding flushing cistern and flush pipe), squating pan including connection to trap and flushing pipe, anit syphonic pipe etc incl making good to floor complete. |
| 58 | S & F in repairs Vitreous China wash down water closet pan (pedestal pattern), white (excluding , low level flushing cistern and Flush pipe of 32mm dia but including seat cover) complete all as specified and directed. |
| 59 | S&F in repairs PVC valve less flushing cistern low level 10 litres capacity with syphonic action type with inlet ball valves, float and handle and connections to pipes and fixing of chain and pull (or) lever including brackets and 32mm dia PVC flush pipe of 60cm long complete all as specified. |
| 60 | S & F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 61 | S&F in repairs vitreous china, wash hand basin white flat back size 550 x 400 mm white complete waste, chain and pug and precelain stopper including bracket. |
| 62 | S & F 32 mm bore brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipes or connections including necessary packing union and cap. |
| 63 | S&F in repairs fancy type pillar tap 15mm dia, cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shank and fly nut screwed for iron pipe . |
| 64 | S&F for 32 mm bore High density polythylene pipes (HDPE) of pressure rating 6Kgf/cm2 fixed compete to in walls, floors,ceilings etc |
| 65 | S&F in repair bib taps concealed type with long shank and cup of fancy type,chromium plated screwed down high pressure with crutch or butterfly handle screwed for iron pipes of 15mm bore. |
| 66 | S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm |
| 67 | S & F PVC (SWR) multiple Floor trap of 75 mm outlet plain with grating including jointing with solvent cement. |
| 68 | S&F in repair Angle valves fancy type,chromium plated cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe of 15mm bore. |
| 69 | S&F in repairs 15mm bore concealled stop valves cast copper alloy fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions. |
| 70 | S&F in repair Brass chromium plated shower rose 125mm size, with or without swivel joints, including fixing to steel pipe or union. |
| 71 | S&F in repair 600 mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers. |
| 72 | S&F in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass 12cm wide with chromium plated bracket guard and railing 60cm long |
| 73 | S&F soap dish, vitreous China white, approximate size 160x 160x90mm |
| 74 | S&F kitchen plate rack of size 910 x 790 x 255 mm made of stainless steel including bedding in cement mortar on to wall or including fixing cantilever brackets |
| 75 | Taking down cement plaster on brick walls including racking out joints, hacking for key, scrubbing down with water etc. |
| 76 | M & L Rendering for 10mm thick in cement mortar (1:6) on other than fair faces of internal bricks or concrete surfaces finished even and smooth with using extra cement all as specified and s directed.. |
| 77 | M&L for rendering 15 mm thick in two layers 10 mm thick backing coat in cm 1:6 and 5mm thick finishing coat in cm 1:4 . mixed with water proofing @ 2% by weight of cement with rough cast plasters finshes. (Note :- WPC will be measured separately). |
| 78 | M & L Rendering 5mm thick on ceiling in CM 1:3 finished even and smooth without using extra cement. |
| 79 | M&L for preparing newly plastered surfaces and applying two coats of distemper oil emulsion over coat of primer on surfaces of walls including 3mm th wall care putty on walls |
| 80 | M&L preparation of newly plastered surfaces of wall and applying three coats of white wash |
| 81 | Material & Labour prepartion of new plastered surface and Finishing walls with Acrylic Smooth exterior paint of required shade with Two or more coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm complete all as specified and as directed. |
| 82 | Material & Labour complete removal & prepartion of existing treated surfaces and Finishing walls with Acrylic Smooth exterior paint of required shade with Two or more coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm complete all as specified and as directed. |
| 83 | M & L complete removal of existing treatment & preparation on walls and applying two coat of distemper oil emulsion over a coat of primer on surfaces of walls including applying 3mm th wall care putty on walls complete all as specified and as directed. |
| 84 | M & L Preparing old plastered surfaces of celings and applying one coat of white wash. |
| 85 | M & L Preparing old plastered surfaces of walls and applying one coat of white wash. |
| 86 | M & L Preparation of new or previously untreated wooden surfaces of any description, exceeding 10 cm width or girth, not otherwise described and applying two coats of Synthetic Enamel paint over a coat of pink primer. |
| 87 | M & L for Preparation of old treated surfaces of any description, exc 10 cm in width or girth when unconnected with other work or painted in different tint and finishing with synthetic varnish for handrail complete all as specified |
| 88 | Taking up or down steel tubing 20mm dia bore and connection complete all as specified |
| 89 | Taking up or down steel tubing 25mm dia bore and connection complete all as specified |
| 90 | Taking up or down steel tubing 40mm dia bore and connection complete all as specified |
| 91 | Cutting chases, pinning in , for concealed water tubing on brick or stone walls, making good to facing where required and pointing in cement mortar 1:3, not exc 10 cm girth complete all as specified and directed. |
| 92 | Supplying and laying of CPVC pipes of outer dia 20mm dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 93 | Supplying and laying of CPVC pipes of outer dia 25mm dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 94 | Supplying and laying of CPVC pipes of outer dia 40mm dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 95 | Supplying and fixing CPVC Brass Elbow (3/4 x 1/2) as in special fittings |
| 96 | Supplying and fixing CPVC Brass Tee of 20mm dia as in special fittings |
| 97 | Supplying and fixing CPVC 40mm dia Male Brass Threaded Adaptor (MTA/ MBTA) ) as in special fittings |
| 98 | Supplying and fixing CPVC 40mm dia UNION as in special fittings |
| 99 | Supplying and fixing CPVC 25mm dia UNION as in special fittings |
| 100 | S & F in repairs Gun metal 40 mm dia of pipe globe or gate valve with Iron wheel head, screwed both end for Iron pipe one fixed. |
| 101 | Taking down rain water pipe and sewage pipe of any size and pattern including all fittings, heads, shoes, bends etc. |
| 102 | S&F for 110mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls. |
| 103 | S&F for 75mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls. |
| 104 | S&F for 75mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring jointslaid in trenches or floors |
| 105 | S&F for 110mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring jointslaid in trenches or floors |
| 106 | S&F for 75mm dia bore PVC (SWR) branch piece, single (Single 'Y') equal or unequal with access door |
| 107 | S&F for 110mm dia bore PVC (SWR) junction single, (Single 'T') equal or unequal with access door |
| 108 | S&F for 75mm dia bore PVC (SWR) bends any radius. |
| 109 | S&F for 110mm dia bore PVC (SWR) bends any radius |
| 110 | S&F for 110mm dia bore PVC (SWR) vent cowl. |
| 111 | S&F for 75mm dia bore PVC (SWR) vent cowl. |
| 112 | Surface Excavation not exceeding 30 Cm deep and averaging 15 Cm deep and getting out in Soft/ Loose soil complete all as specified and as directed. |
| 113 | M&L hardcore of gauge exc 63mm deposited ,spread &levelled in layers n exc 15cm thick,watered and rammed to a true surface. |
| 114 | M & L 75 mm thick Cement concrete type C2, 1:3:6 (using 40 mm graded stone aggregate) in sub base of flooring/ hard standing/pavings/plinth protections. |
| 115 | M&L ATT for treating the soil under plinth protection at the rate of 5.0 ltr of emulsion per sqm of surface area |
| 116 | M&L ATT for treating the soil along with external perimeter of building at the rate of 2.25. ltr of emulsion per mtr of the perimeter walls. |
| 117 | M & L providing ATT by injecting at point of contact of wood work by chemical emulsion (oil or kerosene based solution)@ 0.5 lit/ hole by driling 6mm dia hols at downward angle of 45 degrees at 150 mm centre to centte and sealing the same all as specifiled . |
| 118 | M & L ATT for treatment of soil under existing floors using emulsion @ one litre per hole, 300mm part including drilling and plugging 12mm dia holes with cement mortar 1:2 to match the existing floors. |
| 119 | Demolition of stone slabs and tiles of any description or any thickness in floors, skirtings, risers etc laid ,bedded and pointed in any mortar. |
| 120 | M & L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over rendering 15 mm thick in CM 1:6 complete all as specified.. |
| 121 | M & L 20mm thick Granite (of any type) work (table rubbed and polished) in Skirting for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified.. |
| 122 | Providing edge moulding/ Full nosing to 18-20mm thick Granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete |
| 123 | S & F Cement Concrete tiles 200 x 150 x 20 mm thick machine pressed, jointed and pointed in neat cement slurry in risers and cut and polished with grey cement and pigments including rendering 15mm thick in CM 1:4 all as specified. |
| 124 | S & F Cement Concrete tiles 30cm x 30cm x 20 mm thick machine pressed, jointed and pointed in neat cement slurry in floors and cut and polished with grey cement and pigments including 20mm cement screed in CM 1:6 all as specified., |
| 125 | S & F Chequered cement concrete tiles bullnosed 30 cm x 30 cm x 20 mm thick,as in treads with grey cement and pigments, set, jointed and pointed in neat cement slurry in treads including 20mm cement screed in CM 1:6 |
| 126 | S & F in repairs Ball brass valves of 40mm dia, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in repairs |
| 127 | S&F in repair aluminium wardrobe hooks (single) solid body 50mm to 60mm long. |
| 128 | S & F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm. |
| 129 | S & F MS framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165. |
| 130 | Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles |
| 131 | M & L brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in CM 1 : 6 |
| 132 | Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.) (A) Area exceeding 2.00 sqm each |
| 133 | Providing and fixing factory made uPVG white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.) (A) Area not exceeding 2.00 sqm each. |
| 134 | Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Note: Glass will be measured and paid separately. Net Opening will be measured for payment purpose.) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 08, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Jul 15, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 2 daysJul 15, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysJul 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender