|
| 1 | Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed. |
| 2 | M & L brick work with fly ash bricks, Straight or curved onplan exc 6m mean radius,built in 1:6 in cement mortar all as Specified and Directed |
| 3 | M & L for brick work with sub class \\"B\\" brick (old size) straight or curved on plan to any radius in half brick thick walls built in CM 1:4 to any radius complete all as specified and directed. |
| 4 | Taking down cement plaster any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed. |
| 5 | M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surface of wall and to be finished even and smooth with out using extra cement complete all as specified and directed |
| 6 | Supply only integral water proofing compound all as specified and directed. |
| 7 | M&L for rendering 15mm thick in CM 1:6 on other than fair faces of brick work or concrete surface of wall and to be finished even and smooth with out using extra cement complete all as specified and directed |
| 8 | M&L 5mm thick rendering in CM 1:3 on ceiling surfaces even and smooth without using extra cement complete all as specified |
| 9 | M&L for Preparation of Newly Plastered surfaces of Wall and applying Two coats of Oil Bound Distemper over a coat of primer all as specified and directed. |
| 10 | M&L for preparation of newly plastered surfaces of wall applying two coat of white wash over a coat of primer all as specified and directed. |
| 11 | M&L Preparation of Newly Plastered surfaces of Ceiling and applying Three coats of White Wash complete all as specified and directed. |
| 12 | M&L for Preparation of old surfaces of Wall by brooming down or steel wire brushing, scraping down smoke soot, moulds, mass and efflorescent salts, trading oil and greasy spots etc and applying One coat of white wash over old decorated surface of walls all as specified and directed by Engineer-in-Charge. |
| 13 | M&L for preparation of old plastered surfaces of ceilings and apply one coat of white wash complete all as specified and directed. |
| 14 | M&L for preparation of old distempered surfaces of walls and applying one coat of oil bound distemper on walls all as specified and directed. |
| 15 | M&L for Complete Removal of existing treatment including preparation of old treated surface and applying Two coat of oil bound distemper over 2 mm thick wall care putty including preparation all as specified and directed. |
| 16 | M&L for complete removal of existing treatment incl preparation of New/ old decorated surfaces of wall and applying two coat of cement based paint complete all as specified and directed. |
| 17 | Preparation of Newly Plastered surfaces and applying two coat of Cement Base Paint on walls all as specified and directed by Engineer-in-Charge. |
| 18 | M&L for Preparation of old surfaces of Wall and applying one coat of Cement Base Paint on walls all as specified and directed by Engineer-in-Charge. |
| 19 | M&L for preparation of existing sunken floor treatment incl plaster and removal of all debris with the following specification and sequence complete all directed by Engr-In-Chrg (a) Cleaning internal surface areas of sunken thoroughly to remove all dirt & loose materials by various mechanical/manual means.(b) Providing and making fillets at the junction of the walls and the slabs using CM 1:4. (c) Laying protection plaster 15mm th. in CM 1:4 on floor and wall with integral water proofing compound (d) Applying two coats of Epoxy resin polymer modified cementitious coating like brushbond of FOSROC/ Dr. Fixit Fastflex/ Bostic Powermix both on floor and wall of sunken. |
| 20 | Demolition of cement concrete unreinforced in ground floor and paving n exc 15cm thick (below or above ground level) complete all as specified and directed. |
| 21 | M&L for PCC 1:5:10 type E-2 using 40mm graded stone aggregate as in filling of sunken floor etc and mass concrete complete all as specified and directed. |
| 22 | M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in Sub base flooring 100 mm thick surface finished even and smooth complete all as specified and directed. |
| 23 | M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in sub base flooring 25 mm thick surface finished even and rough to receive the topping layer complete all as specified and directed. |
| 24 | M&L for 100 mm thick Cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed. |
| 25 | S&F machine pressed precast concrete Pre Polished interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and directed. |
| 26 | M&L for sand cushioning including spreading in layers and rolled consolidated to thickness of 50mm (minimum) for receiving precast PCC interlocking blocks complete all as specified and directed |
| 27 | Dismantling floor, hearth or wall tiling including cement mortar bedding etc (but not backing) and removing rubbish off the premises complete all as specified and directed. |
| 28 | M&L for Machine cut kota stone slab flooring mirror finished 18-20 mm thick (each slab not less than 0.25 Sqm) over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab with 15 mm thick screed bed or bedding layer in cement mortar 1:6, including rubbing and polishing complete all as specified and directed. |
| 29 | M&L for Machine cut kota stone in riser of steps, skirting, dado and pillar mirror finished 18-20 mm thick over cement base rendering laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab with 10 mm thick screed bed or bedding layer in cement mortar 1:4, including rubbing and polishing complete all as specified and directed. |
| 30 | M/L Vitrified Ceramic tiles 10 mm thick (square/ rectagular) dark/light colour shade polished,area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floors over 15 mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 31 | M&L Vitrified Ceramic tiles 10 mm thick on vertical surface of wall of size not exceeding 0.36 sqm,as in dado/skitting including 10 mm thick rendering in CM 1:4 complete all as specified and directed |
| 32 | M&L for Non skid ceramic coloured tiles of design as approved by GE 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed. |
| 33 | M&L for Non skid ceramic coloured tiles vertical surfaces area of each tile exceeding 0.06 sq m but not exceeding 0.11 sqm as skirting non skid ceramic tiles ncluding 10 mm thick rendering in CM 1:4 complete all as specified and directed. |
| 34 | M&L for glazed ceramic coloured tiles 350 x 250 x 7 mm / 450 x 350 x 7 mm thick coloured on vertical surface such as dado /skirting / risers to steps etc jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles over and including rendering 10 mm thick in cement mortor 1:4 complete all as specified and directed. Note- (i) The size of tiles (except thickness) may be varied during execution without any price adjustment. |
| 35 | M&L for 20 mm thick granite (of any type & colour) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms/shelves incl screed bed 15 mm th. in CM (1:6) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. |
| 36 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations |
| 37 | Taking up & down GI steel tubing & connections including cleaning for refixing or removal to store for 15mm bore of pipe complete all as specified and directed. |
| 38 | Taking up & down GI steel tubing & connections including cleaning for refixing or removal to store 20mm bore of pipe complete all as specified and directed. |
| 39 | Taking up & down GI steel tubing & connections including cleaning for refixing or removal to store 25mm bore of pipe complete all as specified and directed. |
| 40 | Refixing old steel tubing and connections in new or old position (wall, floor, ceiling etc) of 15 mm bore of pipe complete all as specified and directed. |
| 41 | Refixing old steel tubing and connections in new or old position (wall, floor, ceiling etc) of 20 mm bore of pipe complete all as specified and directed. |
| 42 | Refixing old steel tubing and connections in new or old position (wall, floor, ceiling etc) of 25 mm bore of pipe complete all as specified and directed. |
| 43 | S & F 15 mm bore 3 layer PP-R pipes SDR 7.4 & SDR 11 UV stablised and anti microbial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded PP-R fittings complete to walls, ceilings or in floors complete all as specified |
| 44 | S & F 20 mm bore 3 layer PP-R pipes SDR 7.4 & SDR 11 UV stablised and anti microbial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded PP-R fittings complete to walls, ceilings or in floors complete all as specified |
| 45 | S & F 25 mm bore 3 layer PP-R pipes SDR 7.4 & SDR 11 UV stablised and anti microbial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded PP-R fittings complete to walls, ceilings or in floors complete all as specified |
| 46 | Dismantling PVC water tanks exc 250 ltr but not exc 500 ltr capacity and removing to store |
| 47 | Dismantling PVC water tanks exc 500 ltr but not exc 1000 ltr capacity and removing to store |
| 48 | S&F 500 ltr capacity Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I |
| 49 | S&F 1000 ltr capacity Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I |
| 50 | Cutting chases in brick walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete. |
| 51 | Taking down bib tap/wash basin pillar tap/ stop cock/mixture tap and refixing the same after repair/replacement of spindles for 15 mm bore size complete all as specified and directed. |
| 52 | S&F in repair bib tap cast copper alloy chromium plated with crutch or butterfly handle fixed to 15 mm dia GI tube/CPVC pipe all as specified and directed. |
| 53 | S&F in repair bib tap 2 in 1 type cast copper alloy chromium plated with crutch or butterfly handle fixed to 15 mm dia GI tube/CPVC pipe all as specified and directed. |
| 54 | S&F in repair 15 mm fancy type pillar taps chromium plated cast copper alloy with capstan heads screwed down high pressure with or without lettered ‘Hot’ or ‘cold’ with long screwed shanks and fly nuts . |
| 55 | S&F in repair 15 mm fancy type pillar taps chromium plated cast copper alloy of long swan neck type & quarter turn type with or without lettered ‘Hot’ or ‘cold’ with long screwed shanks and fly nuts . |
| 56 | S&F in repair 15 mm fancy type stop valve/angle valve cast copper alloy chromium plated screwed high pressure with crutch or butter fly handle screwed both ends for iron or union and fixed to 15 mm GI tube complete all as specified and directed by Engineer-in-Charge. |
| 57 | S&F in repair 20mm dia ball Brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipes or brass ferrule and fixed as in PVC Service tanks all as directed. |
| 58 | S&F in repair 25mm dia ball Brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipes or brass ferrule and fixed as in PVC Service tanks all as directed. |
| 59 | S & F in repairs 20mm bore gun metal gate valves with iron wheel head screwed both ends for iron pipe and fixed. |
| 60 | S & F in repairs 25mm bore gun metal gate valves with iron wheel head screwed both ends for iron pipe and fixed. |
| 61 | S&F in repairs PVC connection 15mm size with PTMT nuts, of 450mm length complete all as specified and directed. |
| 62 | S & F in repairs, vitreous china wash basin, white, flat back, size 550x400mm with brackets, inc.cutting for fixing & pinning in ends of brackets complete all as directed by Engr-in-Chrg |
| 63 | S & F in repairs, vitreous china wash basin oval type, white, for fixing in shelves standard size inc.cutting for fixing & pinning in ends of brackets complete all as directed by Engr-in-Chrg |
| 64 | S&F in repairs viterious china squatting pan orissa pattern size 580x440mm white integal foot rest including concrete bedding & including P or S trap 100mm complete all as directed by Engr-in-Chrg |
| 65 | S & F in repairs, vitreous china wash down water closet pan (pedestal pattern), white, incl 'P' or 'S' trap and plastic water closet seat, black, closed pattern with flat bottom and cover & MS chromium plated or aluminised hinging device, complete all as directed by Engr-in-Chrg |
| 66 | S & F in repairs Vitreous China urinals, bowl type flat back size of 465 x 355 x 265 mm white (minimum) with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement etc complete all as sapecified and directed. |
| 67 | S&F in repair PVC low level flushing cistern (white) 10 Ltrs capacity with inlet, ball valve, float and handle internal fitting, push button operated type with and including brackets etc complete. |
| 68 | S/F in repair CP health faucet with flex pipe and hand shover ,the length of hose 1.50 mtr fitted to the tap.complete all as specified |
| 69 | S&F in repairs EWC seat cover of any pattern including cover and Mild steel chromium plated hinging devices of any colour all as specified and directed. |
| 70 | S&F Iin repair CP Grating doom 75 mm dia with PVC (SWR) nahani/floor trap incl jointing with solvent cement complete all as specified and directed. |
| 71 | S&F in repair CP brass towel rail `D’ type 60Cm long fixed to wall all as spd and directed by Engr-in-Charge |
| 72 | S&F Chromium plated Towel Ring fixed with and including Chromium plated brass screws and wooden/plastic cleats(Minimum weight 90 gms) |
| 73 | S&F in repair soap dish any type fixed to plugs with chromium plated brass screws complete all as specified and directed |
| 74 | S&F Looking mirror 5.5 mm thick of selected quality glass of size 600 x 450 mm bevelled edge ,mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plug with chromium plated brass screw and cup washers including aluminium anodized frame complete all as specified and directed. |
| 75 | S&F in repair brass shower rose 125 mm dia any type fixed to plugs with chromium plated brass screws complete all as specified and directed |
| 76 | S&F as in repair glass shelf assembly consisting of 5.5mm thick sheet 12cm wide with chromium plated bracket guard railing 60cm long complete all as specified and directed |
| 77 | S&F as in repair cornner glass shelf of size 9\\"*9\\" shelf and frond,circle in design fixed over chromium plated brackets of heavy duty with frond linings with glass fixed in wall with necessary screws complete all as specified and directed. |
| 78 | S & F in repair Lid of water tank capacity of 500/1000/2000 Ltrs including necessary cleats/clamps complete all as specified and directed. |
| 79 | M&L for cleaning of water storage tank of capacity upto 500 ltrs mountred on roof incl removal of all vegetation if any, loose dirt and all other materials with help of tank cleaning motor jet pressure machine and pouring bleaching powder @0.25 kg per tank with date of cleaning clearly written over tank incl Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in positionall as directed by Engr-in-Chrg |
| 80 | M&L for cleaning of water storage tank of capacity exc 500 ltr but not exc 1000 ltrs ,size,type etc.mountred on roof incl removal of all vegetation if any, loose dirt and all other materials with help of tank cleaning motor jet pressure machine and pouring bleaching powder @0.25 kg per tank with date of cleaning clearly written over tank ncl Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in positionall as directed by Engr-in-Chrg |
| 81 | S & F in repair LDPE waste pipe for WHB, sink, urinal etc. pipes of pressure rating 6 kgf/sq. cm complete. |
| 82 | S & F in repair HDPE waste pipe 32 mm dia for EWC,Flushing cistern etc. pipes of pressure rating 6 kgf/sq. cm complete. |
| 83 | S & F in repair HDPE pipe 40 mm dia of pressure rating 6 kgf/sq. cm complete. |
| 84 | S & F in repair 32mm dia Bottle trap of PTMT having minimum water seal of 25 mm all as spd. |
| 85 | S & F in repair 32mm dia bore Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc.with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed as in repairs |
| 86 | Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete,PVC ) set in cement mortor for any size & type complete all as specified and directed. |
| 87 | M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls or in floors of 75 mm bore of pipe etc complete all as specified and directed. |
| 88 | M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints,fixed to walls or in floors of 110 mm bore of pipe etc complete all as specified and directed. |
| 89 | S&F PVC (SWR) bends any radius of 75 mm bore with out access door complete all as specified and directed. |
| 90 | S&F PVC (SWR) bends any radius of 110 mm bore with out access door complete all as specified and directed. |
| 91 | S&F PVC (SWR) bends any radius of 75 mm bore with access door complete all as specified and directed. |
| 92 | S&F PVC (SWR) bends any radius of 110 mm bore with access door complete all as specified and directed. |
| 93 | S&F PVC (SWR) vent cowl 75 mm bore complete all as specified and directed. |
| 94 | S&F PVC (SWR) vent cowl 100 mm bore complete all as specified and directed. |
| 95 | Taking down chowkhat or frames n exc 1.50 Sqm each with shutters (without taking off shutters from the frame) and removing to or from store complete all as specified and directed |
| 96 | Taking down chowkhat or frames exc 1.50 Sqm and n exc 4 Sqm each with shutters (without taking off shutters from the frame) and removing to or from store complete all as specified and directed |
| 97 | S & F for solid PVC door frame of size 50x47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening as specified and shown on drawing made on section 8 of SSR 2010 Part-II complete all as specified and directed |
| 98 | S & F factory made solid panel PVC door shutter 30 mm thick style consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC “C” channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, S & F in the frame as per specifications and shown on drawing in section 8 of SSR-2010 Part-II complete all as specified and directed |
| 99 | S&F 100 mm long butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised type B-21 complete all as specified and directed. |
| 100 | S&F 150 mm size extruded aluminium alloy handles fabricated type anodised of complete all as specified and directed. |
| 101 | S&F 150 mm long aluminium,anodised, barrel tower bolts of extruded section complete all as specified and directed. |
| 102 | S&F in repair 100 mm long butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised type B-21 complete all as specified and directed. |
| 103 | S&F in repair 150 mm size extruded aluminium alloy handles fabricated type anodised of complete all as specified and directed. |
| 104 | S&F in repair 150 mm long aluminium,anodised, barrel tower bolts of extruded section complete all as specified and directed. |
| 105 | S&F in repair 300 mm long aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. |
| 106 | S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4 mm fixed with stainless steel wire staples or with necessary beads complete all as specified and directed. |
| 107 | S&F in repair for 25mm dia Stainless Steel Curtain Rod with brackets on both ends incl T/D of any type old curtain rods and making good disturbed surfaces with cement mortar or putty complete all as specified and directed |
| 108 | M&L in repair 18/19 mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work incl taking down old cupboards etc. complete all as specified and directed. |
| 109 | S&F 100 mm long Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws |
| 110 | Dismantling of wall and ceiling boards (fibre,pulp,insulation,etc)or insulation boards/slabs/blankets,any thickness,including cover fillets. complete alll as specified and directed |
| 111 | Providing & fixing false ceiling at all heights with Semi perforated 12 mm thick micro tegular edged GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 1200 x 600 mm of approved texture,design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of mainT runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm , suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1 OOOmm length and Lshape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-inCharge. |
| 112 | M&L for applying 3 mm thick wall care Putty in two layers on ceiling surfaces absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper including and applying two coats of Oil bound distemper on ceiling complete complete all as specified and directed. |
| 113 | M&L 4 mm th. non asbestos fibre cement board fixied to GI/Aluminium framework with screws fixed in ceilings of size 600 x 600mm board incl anodised aluminium snap grid frame work for false ceiling all as specified and directed by Engr-In-Charge |
| 114 | Taking down UPVC door and windows/ventilator of any size and of any description built in wall complete all as specified & directed. |
| 115 | Providing and fixing factory made uPVC white colour casement ( Openable) Door made of extruded profiles with wall thickness of 2.3 mm (+-0.2 mm) window profile with hollow section with multi chamber . Frame (60 mm × 58 mm) sash (60 mm × 78 mm). T- Profile (one vertical length in two shutters)(60mm x 74mm) Glazing bead (35 mm × 20 mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2 +- 0.2 mm thick galvanized steel Frame (28 mm × 21.5 mm) sash (31mmx27mm) T- Profile(27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm × 100 mm long fasteners. HARDWARE: (Casement door handle made of zinc alloyed (white coloured coated),corner striker,secondary striker,cylinder,Door transmission gear made of mild steel with multi point locking system with strikes,3D Hinges of Zinc alloyed(white powder coated) and 5mm thick glazing with selected quality glass (Note: The unit rate quoted by contractor include cost of glass and includes all other connected accessories. |
| 116 | S&F factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and including 5mm thick glazing with selected quality glass & required accessories. (Note: The unit rate quoted by contractor includes cost of glass and includes all other connected accessories. |
| 117 | Providing and fixing factory made uPVC white colour fixed window made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing withselected quality glass (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories Net opening will be measured for payment purpose. (A) Area exceeding 1.00 sqm but not exceeding 2.00 sqm each |
| 118 | Taking down aluminium door and windows/ventilator of any size and of any description built in wall and making good at disturbed surface with cement mortar 1:4 and applying two coats of plastic emulsion paint as per existing treatment complete all as specified & directed. |
| 119 | S&F Powder coated Aluminium anodised glazed side hung door shutters with anodised aluminium frame of section of 100x44x2mm and bottom rail of 44.5x99x1.8mm including 5.5mm thick tinted sheet glass ordinary quality with all necessary suitable push & pull plate/handle , screw, jointing cleats, rubber packing aluminium snap beading and 1 No 200mm long Aluminium tower bolt, 100mm long 3 No Aluminium butt hinges B-21 Type and one No mortice brass lock 100 size 4 leaver (Vertical Type) with 01 No door closer Aluminium (Diie cast) body hydraullically regulated designation No 02 universal type, for each shutters complete all as specified and directed |
| 120 | S&F Powder coated three track Aluminium sliding window with frame not less than 1.8 mm thick including 4 mm thick tinted glass, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket, aluminium snap beading & necessary rubber packing, locking, roller & opening arrangement, incl Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm, all fitting and fixtures complete all as specified and directed by Engr-In-Charge |
| 121 | S&F Powder coated Aluminium Ventilator with frame not less than 1.8 mm thick & including 4 mm thick tinted glass including beading & necessary rubber packing, locking & opening arrangement if required, all fitting and fixture complete all as specified and directed. |
| 122 | S&F 5 to 6 mm thick aluminium grills of good quality surrounded by aluminium 'C' channel incl taking down old grills of any type complete all as specified and directed. |
| 123 | S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed. |
| 124 | S&F in repair door closer hydraulically regulated designation No 2, universal type, suitable for door shutter of weight not more than 60 Kg of aluminium (extruded section body) complete all as specified and directed. |
| 125 | Excavation of trenches in any type of soil n.exc 1.5 M wide and n.exc 1.5 M in depth for taking out/laying of pipe lines and getting out forming bottom surfaces to required gradients complete all as specified and as directed. |
| 126 | Returning, filling in and including spreading, leveling, watering and well ramming in layers n.exc 25 cm thick complete all as specified and directed |
| 127 | Removing excavated surplus materials to a distance not exceeding 50 Mtrs and deposited where directed at a level not exceeding 1.5 Mtr. Above starting point complete all as specified and directed. |
| 128 | Taking up or down old unserviceable GI pipe line and S&F 3-layer PP-R polypropylene random copolymer concealed pipe (PN 16/SDR 7.4) UV stablised and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings, floors or in trenches etc of size 110 mm OD complete all as specified and directed. Make : SFMC or equivalent in approved by E-in-C |
| 129 | All as per Item No. 128 above but of size 90 mm OD. |
| 130 | All as per Item No. 128 above but of size 63 mm OD. |
| 131 | All as per Item No. 128 above but of size 50 mm OD. |
| 132 | All as per Item No. 128 above but of size 32 mm OD. |
| 133 | All as per Item No. 128 above but of size 25 mm OD. |
| 134 | S&F in repair of PP-R gate valves(brass inlet) as per requirement of size 63 mm OD complete all as specified and directed. |
| 135 | All as per Item No. 134 above but 50 mm OD. |
| 136 | All as per Item No. 134 above but 32 mm OD. |
| 137 | All as per Item No .134 above but 25 mm OD. |
| 138 | S&F in repair of PP-R male threaded coupling (brass inlet) as per requirement of size 110mm OD complete all as specified and directed. |
| 139 | S&F in repair of PP-R male threaded coupling (brass inlet) as per requirement of size 63mm OD complete all as specified and directed. |
| 140 | All as per Item No. 139 above but 32 mm OD |
| 141 | S&F in repair of PP-R Female threaded coupling (brass inlet) as per requirement of size 110mm OD complete all as specified and directed. |
| 142 | S&F in repair of PP-R Female threaded coupling (brass inlet) as per requirement of size 63mm OD complete all as specified and directed. |
| 143 | All as per Item No. 142 above but 32 mm OD |
| 144 | M & L in replacement and making connection of PP-R distribution branch with PP-R mains of size (16 to 40mm) by providing and fixing tee including cutting and making fusion joint etc as per required at site. |
| 145 | M & L in replacement and making connection of PP-R distribution branch with PP-R mains of size (50 to 75 mm) by providing and fixing tee including cutting and making fusion joint etc as per required at site. |
| 146 | Boring across the road/hard surface with machanical boring equipments not less than 80 mm bore dia all as specified and directed. |
| 147 | S&F in repairs Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 1 20mm-210gms./ 25mm-455gms) of size 20 mm dia complete all as specified and directed. |
| 148 | All as per Item No 147 above but 25mm dia |
| 149 | Supply and fixing Ceiling Fan 1200 mm sweep with blade, down rod complete all as specified and directed. |
| 150 | Supply and fixing street light fitting LED type 25 Watt new generation in aluminium PDC housing, toughened glasscover with IP 66 protection complete in all respect with GI tubing 25mm/40mm dia, mounting bracket with its clamp incl two coats of synthetic enamel paint over a coat red oxide primer and with all accessories, incl connecting of with 2 run of flexible aluminium/copper conductor of size 1.5 sq mm cable from fitting to junction box/conductor to street light as suitable on site, testing & commissioning complete all as specified and directed. |
| 151 | S&F foot valve 100 mm dia CI/GI/DI with complete fittings including taking out old unsv complete all as specified and directed. |
| 152 | S&F foot valve 80 mm dia CI/GI/DI with complete fittings including taking out old unsv complete all as specified and directed. |
| 153 | S&F in replacement of NON return valve 80 mm bore class PN - 1.6 with flanged including jointing materials,rubber gasket suitable size nut bolts and washer etc complete all as specified and directed. Please Enable Macros to View BoQ information |
