|
| 1 | Repair to potholes any depth, not exceeding 1 sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc., cutting around edges to at least 25 mm in depth, making good by applying tack coat at the rate of 5 kg per 10 Sqm, putting in bituminous macadam well rammed (including supply of bituminious carpet, binder and chhipping) and sealed with bitumen 9.8 kg per 10 sqm blinded with 0.09 cum stone chippings, 6.3 mm size depth of pot holes exc 30mm and rolled and compacted with power roller 8 to 12 tonnes to required camber and gradient complete all as specified and as directed. |
| 2 | Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area exceeding 400 sqm, depth of pot hole exceeding 50 mm but not exceeding 100 mm including rolling over the broken surfaces using 8 to 10 tonnes power roller to required camber and gradient complete all as specified and as directed. |
| 3 | M&L for preparation of Unsurfaced water bound macadam by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc and applying evenly a priming/tack coat with bituminous primer at 10kg per 10 sq meters of paving bitumen (VG10) complete all as specified and directed. |
| 4 | Material and labour for providing premixed bituminous macadam laid/rolled and compacted to required gradient and camber using 8 to 10 tone capacity power roller (consolidated thickness 75mm or less) using paving bitumen (VG 30 Grade) @ 4% by weight of total mix complete all as specified and directed. Note:- (i) The exact bitumen content required shall be determined Mix Design procedure and approved by GE. The adjustment in rate on MINUS side variation in quantity of bitumen if any shall be priced at the rate of ₹95 per kg. No claim whatsoever shall be made for adjustment in plus side. (ii) Bituminous macadam shall be laid using self propelled hydrostatic paver finisher and preparation of mix shall be using hot mix plant and transporting the mix in tipper. |
| 5 | Preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc., sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc. complete all as specified and as directed. |
| 6 | M & L for applying evenly a tack coat with bituminous primer (paving grade bitumen VG-10 grade) @ 5 kg per 10 sq metres complete all as specified & as directed. |
| 7 | Material and labour for bituminous premixed semi-dense asphaltic concrete, 40mm consolidated thickness using 5.5% paving bitumen (VG 30 Grade) binder content any penetration by weight of total mix, mixed in central computerized hot mix plant and laid using mechanical self propelled paver and rolled and compacted with 8 to 12 tonne power roller to uniform surfaces with required camber and gradient complete all as specified and as directed.Note:- Semi dense asphaltic bituminous concrete shall be designed as per design mix. Contractor shall quote his unit rate considering the bitumen contents as 5.5 %. Any variation in binder content on minus side shall be adjusted at the rate of ₹95.00 per KG of binder. No adjustment in price shall be made if the variation is on plus side. |
| 8 | Material and labour for preparing bituminous surfaces of road and marking 2.5mm thick centre lines stop line dashe arrow etc and the like not exceeding 10cm wide on road pavement with hot applied thermo plastic road marking paint with reflectorizing glass beads on bituminious surface @ 250gms/ sqm area as per IRC: 35- 1997 of approved colour conforming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed. |
| 9 | S&F in repair speed breaker of size 750mm X250 mm X75mm made out of ABS material with two highly reflective reflectors moulded in PMMA materials welded with ABS plate through ultrasonic welding process fixed on to the speed breaker so the dust and water can not touch reflectors inside and fixed complete all as specified and directed. |
| 10 | S&F in repair traffic convex mirror of of 60cm dia having 130 degree viewing angle made of polycarbonate material , brim and back holding plate is made of metal/FRB along with pole mounted brackets and pole 60mm dia made with galvanised steel pipe of suitable length fixed to the ground by means of PCC 1:2:4 type B2 (using 40mm dia graded stone aggregate) in foundation/filling (size 50cmx50cmx60cm) all as specified and as and as directed. |
| 11 | S & F in repair metal tubular delineators (road way indicators) made out of ABS round body fitted with 2 Nos of 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm mild steel pipe of 600 mm height duly power coated and thermo plastic elastomers 3 bands of green, red and yellow reflector radium tape of 25 mm wide strip with anti theft steel net for reflector protection including embedded 200 mm below ground level including excavation and PCC M15(Nominal Mix) (150x150x300mm) with using 20 mm graded stone aggregate in foundation and making good surface complete all as specified and as directed. |
| 12 | S&F in repair cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of suitable size as per manufactures instructions complete all as specified and directed. |
| 13 | Supply and fixing in repair solar cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/ 0.3 watt one NI-ed rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd, 3 pieces each side and total 6 pieces are used for high brightness and backup for 12 hours completed as per manufactures instructions etc complete all as specified and as directed. |
| 14 | Demolition of cement concrete(unreinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level) and complete all as specified and as directed. |
| 15 | M & L for cement concrete in foundation, filling and mass concrete in M15(Nominal Mix) using 40 mm nominal size graded crushed stone aggregate complete all as specified and as directed. |
| 16 | M & L for cement concrete M7.5 (Nominal Mix) using 40 mm nominal size graded crushed stone aggregate 75 mm thick in sub base for laying tiles, pavings, floorings etc. complete all as specified and as directed. |
| 17 | M & L for hardcore (broken stone or boulders) of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed. |
| 18 | M & L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed. |
| 19 | Providing and laying 80 mm thick factory made cement concrete interlocking paver block of M40 grade conforming to IS 15658-2006 made by block making machine with strong vibratory compaction, of approved size, design & shape with grey cement and no pigment complete all as specified and directed. |
| 20 | Demolition of ashlar facings, dressed stonework, precast concrete articles and precast concrete block walling built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed. |
| 21 | M & L for precast cement concrete solid block masonry of grade C(5.0) with concrete M 10 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate exceeding 10 cm in width and set in cement mortar (1:6) complete all as specified and as directed. |
| 22 | Material and labour for plastering 15 mm thick (in two layers of 10mm and 5mm thk) on fair faces of brick wall or concrete surfaces in cement mortar 1:4 with water proofing compound as per manufacturer's printed instruction finished even and fair complete all as specified and directed.Note: (i) Water proofing compound shall be measured and paid for separately. (ii) The cost of scaffolding is included in this item. |
| 23 | Supply only integral water proofing compound complete all as specified and directed. |
| 24 | M&L for preparation of newly plastered surfaces on walls and applying three coats of white wash complete all as specified and as directed. |
| 25 | Manufacturing, supplying and fixing retro reflective Mandatory/ Regulatory sign boards of 900 mm diametre with support length of 3750 mm and made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-charge including taking down old. |
| 26 | Manufacturing, supplying and fixing retro reflective Overhead informatory sign boards of round in shape of dia 900mm with support length of 3650mm and made up of 2mm thick aluminium sheet, face to be fully covered with high intensity encapsulated lens type heat activated retro reflective sheeting conforming to type -III of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloy rivets bolts @ 30 cm c/c all along the periphery as well as in two vertical rows alongwith theft resistant measures, including painted with two or more coats of grey colour epoxy paint on the backside of aluminium sheet to be painted with two or more coats of over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-charge.Note- (i) The rate includes the cost of rounding off the corners, structural framework and lowering down the structural frame work from the gantry, fixing and errecting the same in position. (ii) Rectangular area of the sheet shall be measured for payment purpose. Please Enable Macros to View BoQ information |
