Tender For Addn/Altn To Offr Toilet, Bathroom At Quarter Guard And special Repair To Hardstanding Near P 1040 At Chandimandir
Tender Value
43.50 Lakhs
Estimated cost
Bid Submission
11 Jul 2026
2 days left
EMD
87000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Panchkula → Haryana
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Addn/Altn To Offr Toilet, Bathroom At Quarter Guard And special Repair To Hardstanding Near P 1040 At Chandimandir
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brickwork or stone/ boulder masonry, built in lime mortar including all quoins, arches pillars etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 2 | Brick work with sub class ‘B’ bricks old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:4 complete all as specified & directed. |
| 3 | All as per serial item No 02 herein before but except bricks (using old serviceable bricks obtained from ser item No 02 here-in-above) complete all as specified & directed. |
| 4 | Rendering 15mm thick on fir faces of brick work or concrete surface in CM 1:4 surface finished even and smooth without using extra cement. |
| 5 | Rendering 15mm thick on fir faces of brick work or concrete surface in CM 1:6 surface finished even and smooth without using extra cement. |
| 6 | Rendering 5mm thick in Cement and Sand mortar 1:3 concrete surfaces as in ceiling / chajjas facia at any position finished even and smooth without using extra cement, including taking down old cement plaster complete all as specified and directed. |
| 7 | Demolition of reinforced cement concrete in roofs, floors, beams, staircases, landing, chajjas and similar suspended work, complete all as specified and directed. |
| 8 | Excavation in trenches in hard/dense soil not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation etc. or for shafts, wells cesspits, manholes, pier hole etc. and getting out, complete all as specified. |
| 9 | providing cement concrete type D2, 1:4:8 using 40 mm graded stone aggregate, as in foundations, filling and mass concrete etc., complete all as specified and as directed |
| 10 | Reinforced cement concrete type A-1, 1:1½:3 (nominal mix, using 20mm graded crushed stone aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed |
| 11 | Reinforced cement concrete, type A-1, 1:1½:3 (nominal mix, using 20mm graded crushed stone aggregate) as in coloumns, pillars etc complete all as specified and directed (reinforcement shall be measured and paid for separately). |
| 12 | Reinforced cement concrete, type A-1, 1:1½:3 (nominal mix, using 20mm graded crushed stone aggregate) as in beams, cantilevers, bressumers, lintels over 1.5 metre span and the like complete all as specified and directed (reinforcement shall be measured and paid for separately). |
| 13 | Material and labour reinforced cement concrete 1:1.5:3, nominal mix, type A-1 using 20mm graded crushed stone aggregate as in Chajja and similar works, all as specified. Note : Reinforcement and form work shall be measured and paid separately |
| 14 | Reinforced cement concrete type A-1, 1:1½:3 (using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams, balconies, roofs, canopies shelves and the like complete all as specified and directed. |
| 15 | Form Work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundations and plinth beams and similar work, vertical or to batter to give rough finish to flat surfaces complete all as specified and directed. |
| 16 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed. |
| 17 | Form work to edges of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls, floor and roofs exc 20cm wide and side of RCC / PCC bends in walls , horizontal or sloping and similar work. |
| 18 | Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm complete all as specified and directed. |
| 19 | Mild steel TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips as in stirrups complete all as specified & directed. |
| 20 | Earth filling under floor including watering and consolidation in layers n.exc 25cm thick complete all as specified & directed. |
| 21 | Hard core of broken stone or boulders of gauge exc. 63mm but n.exc 100mm, deposited, spread and leveled in layers n.exc. 15cm thick, watered and rammed to a true surface complete all as specified & directed. |
| 22 | 100mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in sub base etc, finished even and rough complete all as specified and directed. |
| 23 | 50mm thick plain cement concrete type C-1 1:3:6 (Using 20mm graded crushed stone aggregates) as in plinth protection finished fair and even without using extra cement complete all as specified and directed. |
| 24 | 25mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in flooring, finished even and fair complete all as specified and directed. |
| 25 | Returning filling in including spreading, levelling, watering and well ramming in layers not exc.25cm thick each layer of soil all as specified. |
| 26 | Removal of excavated material to distance exceeding 200 metre but n exc 500 and depositing where directed at a level not exceeding 1.5 metre above the starting pointurning, filling in including spreading, levelling, watering and well ramming in layers not exc 25cm complete all as specified and directed. |
| 27 | Supply only integral water proofing compound complete all as specified & directed. |
| 28 | Framed work such as grill guard bars etc welded to steel frame MS round/square bar conforming to Fe 410 Gde-E 165 complete all as specified and directed. |
| 29 | 4mm thick figured glass pin head type ordinary quality any size and in any type of frame and glazing with oil putty in square n.exc 0.5 Sqm in each panes complete all as specified and directed. |
| 30 | Galvanised mild steel wire cloth 0.56 mm nominal dia of wire & avg width of aperture 1.18 mm in fixed with stainless steel wire complete all as specified and directed. |
| 31 | Three coats of white wash on plastered or unplastered ceiling surfaces including preparation of new surfaces complete all as specified and directed |
| 32 | Preparation of new plastered surfaces of walls and applying two coats of cement base paint, complete all as specified and directed. |
| 33 | Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed. |
| 34 | Cleaning top surface, terracing or cement concrete, including flashings and junction of parapets, etc., and adjoining vertical surfaces and applying bituminous primer @ 0.40 litres per square Metre including APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced with polyester non woven fabric (weight not less than 150 gms/sqm) laid on primed surface by torch application & membrane complete all over and including 20mm thick rendering in CM 1 :4 mixed with water proofing compound complete all as specified and directed.Note : WPC shall be measured and paid separately |
| 35 | Granite work (of any type table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in, set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite compelte all as specified and directed. |
| 36 | Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, and fixing in opening as per specification complete all as specified and directed. |
| 37 | Factory made solid PVC moulded door shutter,with wood free EPS core 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site complete all as specified and directed. |
| 38 | 100mm size, butt hinges, medium weight, cold rolled mild steel cmplete all as specified & directed. |
| 39 | 150 mm size aluminium anodized, barrel tower bolt of extruded section and fixed complete all as specified and directed. |
| 40 | 150mm Extruded aluminium alloy handle fabricated type, complete all as specified and directed. |
| 41 | Aluminum alloy, anodized, sliding door bolt 250mm long hasp , staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed, complete all as specified and directed. |
| 42 | Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar (1:3) for concealed pipe etc and making good, cutting not exceeding 10cm girth complete all as specified & directed by Engineer-in-charge. |
| 43 | Non skid, first quality ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area or each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed. |
| 44 | Glazed ceramic coloured tiles of size 300mmx450mmx7mm on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed. |
| 45 | 15 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors, fixed as in repair complete all as specified and directed. |
| 46 | 20 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors fixed as in repair complete all as specified and directed. |
| 47 | 25 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors, fixed as in repair complete all as specified and directed. |
| 48 | PVC (SWR) pipe 110mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed. |
| 49 | PVC (SWR) pipe, 75mm bore, single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed. |
| 50 | 110mm bore PVC (SWR) bends any radius complete all as specified and directed |
| 51 | 75mm bore PVC (SWR) bends any radius complete all as specified and directed |
| 52 | 110mm bore PVC (SWR) junction single, (Single T) equal or unequal, complete all as specified and directed. |
| 53 | 75mm bore PVC (SWR) junction single, (Single T) equal or unequal, complete all as specified and directed. |
| 54 | 75/ 110mm bore PVC (SWR) vent cowl any radiuscomplete all as specified and directed. |
| 55 | PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed. |
| 56 | 1000 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) Double layered hoisted and fixed in position, including tank nipple, float valve of PTMT 20mm bore etc, fixed as in repair complete all as specified and directed. |
| 57 | Ceramic wall mount/hung western toilet/rimless commode/water closet with softclose seat cover 52x 36x36cm (white colour) including all necessary accessories as requried to fix the WC, complete all as specified and directed. |
| 58 | Vitreous China Urinal, Half stall type, white and including flushing cistern, flush pipe and waste pipe, fixed as in repair complete all as specified & directed |
| 59 | Vitreous china urinal partition white of size 310 x 700mm urinal partitions slabs terminating about 40cm above floor line complete all as specified and directed. |
| 60 | Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) fixed as in repair complete all as specified and directed. |
| 61 | Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect, fixed as in repair complete all as specified and directed. |
| 62 | Liquid soap container of CP fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms) complete all as specified and directed. |
| 63 | Towel ring of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 90gms), fixed as in repair complete all as specified and directed. |
| 64 | Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with CP bracket guard and railing 60cm long, fixed as in repair complete all as specified and directed. |
| 65 | Toilet paper holder, stainless steel, chromium plated fixed in position, fixed as in repair , complete all as specified and directed. |
| 66 | Bevelled edge mirror size 600mm x 450 mm, 5mm thick of selected quality glass mounded on 5 mm thick PVC board fixed to wooden plugs with chromium plated brass screws and cup washer with aluminium channel of suitable section alround , all as specified & directed. |
| 67 | PVC connections 15 mm size with PTMT nuts of length 450 mm , fixed as in repair complete all as specified and directed. |
| 68 | PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75mm bore, fixed as in repair complete all as specified and directed. |
| 69 | Vitreous China designer counter top wash basin/tabletop of size 18x13x5 inch white gold designer tip, including CP waste coupling and PVC waste pipe fixed as in repair complete all as specified and directed. |
| 70 | 15mm Brass basin mixer tap, chromium plated, screwed down high pressure , with or without lettered Hot or Cold with long screwed shanks and fly-nuts, scewed for iron pipe and fixed, fixed as in repair complete all as specified and directed. |
| 71 | Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed. |
| 72 | Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 20mm bore pipe, fixed as in repair complete all as specified and directed. |
| 73 | Angular stop cock, fancy type, cast copper alloy chromium plated, screwed down, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in reapir complete all as specified and directed. |
| 74 | Bib tap, fancy type cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed. |
| 75 | PVC valve less syphonic action type flushing cistern low level white with PVC in let ball valve, float and handle, 10 ltrs capacity and connection to pipes including PVC connection with PTMT nuts and 32mm dia CP flush pipe (long type for squatting pan), fixed as in repair, complete all as specified & directed. |
| 76 | Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge |
| 77 | Powder coated aluminium (minimum thickness of powder coating 50 micron) for frame / shutters of doors, windows & ventilators (Sliding, openable / three track including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 78 | Door closer hydraulically regulated aluminum (die cast) body, designation No 3, universal type, suitable for door shutters of 701mm to 850mm in width and of weight between 36 to 60 Kg, fixed as in repair complete all as specified and directed. |
| 79 | Supply only 3mm thick aluminium composite panel sheet (ACP) of colour as approved by Engr In Charge, all as specified and directed. |
| 80 | Providing and fixing false ceiling at all heights with GRG (Glass Fibre Reinforced gypsum) false ceiling tiles of size 595x595mm of approved texture, designand patterns having moisture content less than 2% humidity resistance of 99% NRC 0.50 to 0.75 as per IS 8225:1987, Non-combustible as per BS 476 (part 4) - 1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33 mm thick (galvanised @ 120 grams per sqm includig both sides) comprising of main T runners of size 15x32 mm of length 1200mm and secondary module of size 600x600mm, suspended from ceilingusing galvanised mild steel items (galvanizing @ 80 grams per sqm) ie., 50mm long 8mm outer diaMetre M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size 85 X 25 x 0.40 mm of length 3000mm to be fixed on periphery wall/patition with the help of plastic rawl plugs at 450mm centre to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per direction of Engineer-in-charge. |
| 81 | HDPE double wall corrugated (DWC) pipes (ISI Marked) 150mm SN-8 class as per IS 16098 Part -II for non pressure underground drainage and sewage applications with speials including cost of special O rubber rings couplers etc, laid in trenches on concred bed to level / gradient, jointing with appropriate class fittings as per manufacturer's instructios including jointing accessories and fittings complete all as specified and directed. |
| 82 | PCC 1:3:6, type C-2 (using 40mm graded crushed stone aggregate), concrete bed to drain pipes of 150mm bore pipe including packing under and hunching against the sides of the pipe after they are laid and tested complete all as specified and directed by Eng-in-charge. |
| 83 | Mangalore pattern roof tile interlocking at side joints, laid over including 20mm thick screed bed in CM 1:4 complete all as specified and directed |
| 84 | Ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in cement mortar 1:6 complete all as specified and directed |
| 85 | Automatic hand dryer for bathroom stainless steel super high speed for fast drying, energy efficient compete. |
| 86 | Napkin hanger for bathroom silver with chrome finish, corrosion resistant premium metal construction for durability modern design complete. |
| 87 | PVC (SWR) pipe 110mm bore single socketed in any length with rubber ring joints, fixed to walls or floor etc, complete all as specified and directed. |
| 88 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviveable tiles to store and rubbish off the premises complete all as specified and directed |
| 89 | 20mm thick Granite work (of any type table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in, set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite compelte all as specified and directed. |
| 90 | Taking down chowkhats or frame n.exc 1.5 Sqm with shutter (without taking off shutters from the frame) and removal from site complete all as specified & directed. |
| 91 | Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100/ 50 x 75 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 92 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in- Charge |
| 93 | 125mm Extruded aluminium alloy handle fabricated type, complete all as specified and directed. |
| 94 | Butt hinges (ISI marked) 100mm size, of extruded aluminum alloy with galvanised mild steel hinge pin, anodised, type C-21, complete all as specified and directed. |
| 95 | 200mm aluminium anodized barrel tower bolts of extruded section complete all as specified and directed. |
| 96 | 4mm thick sheet glass ordinary quality any size and in any type of frame and glazing with oil putty ( or beading ) in square n.exc 0.5 Sqm in each panes complete all as specified and directed. |
| 97 | stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm including fixed with stainless steel wire staples complete all as specified & directed. |
| 98 | PVC (SWR) pipe 75mm bore single socketed in any length with rubber ring joints, fixed with walls, complete all as specified and directed. |
| 99 | PVC (SWR) floor trap 100mm bore, plain with grating incl jointing with solvent cement, complete all as specified and directed. |
| 100 | Vitreous china squatting pan \\"orissa\\" pattern, size 580 x 440 mm white, with integral foot rest including 'P' or 'S' trap, flush pipe (excluding flushing cistern) and making good to the floor fixed as in repair complete all as specified & directed by Engineer-in-charge. |
| 101 | Towel ring of CP fixed with and including chromium plated brass screws and wooden / plastic cleats fixed as in repair complete all as specified and directed. |
| 102 | Vitreous China wash basin, angle back, size 600x480 white, excluding taps, waste, chain and plug and porcelain stopper but including brackets |
| 103 | Taking down chowkats or frame exc. 1.5 Sqm and n exc 4 Square metre with shutters, without taking off shutters from the frame, complete all as specified and directed. |
| 104 | Supply only 5.00mm thick ordinary quality tinted glass, fixed to aluminum frame work in panels exc 0.5 Sqm in each pane, complete all as specified & directed. |
| 105 | 15mm thick rendering in Cement and Sand mortar 1:6 over concrete /brick surfaces finished even and smooth without using extra cement and providing necessary scaffolding , safety precautions and other requisite arrangements all as per site requirement complete all as specified & directed. |
| 106 | Cement concrete type B-1, 1:2:4 using (20 mm graded crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, parapets and railings upto 60 cm in height, copings, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including the use of forms or moulds with plain faces complete all as specified and directed. (Cement concrete item shall be reinforced, where ordered. Reinforcement shall be measured and paid separately. |
| 107 | 100mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base etc, finished even and rough complete all as specified and directed. |
| 108 | Sand filling under floors, inter locking tiles/paver blocks or in foundations including watering and consolidation complete all as specified |
| 109 | Demolition of stone slabs and tiles of any description or thickness in floors laid, bedded and pointed in any mortar including disposal of demolished material complete all as specified and directed. |
| 110 | Machine pressed Concrete interlocking paver block, any shape and size conforming to IS 15658-2006 of 80 mm thickness, M-40 Grade with gray cement and pigment complete all as specified and directed |
| 111 | Precast concrete interlocking paver block, with grey cement and no pigment, design as approved, any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade, and including laid over 25mm thick sand cushioning, complete all as specified and directed |
| 112 | Factory made rubber moulded machine pressed coloured chequered cement concrete tiles 250mm x 250mm x 22-25mm thick (with grey cement and pigments), set, jointed and pointed in neat cement slurry with grey cement with pigment to match the colour of tiles, glossy finish, laid over and including 20mm thick screed bed in cement mortar 1:4, complete all as specified and directed. |
| 113 | Exterior grade, coloured, non skid porcelain tiles (Parking tiles), heavy duty of size 300mm X 300mm X 9-10mm as in floor, set and jointed in neat slurry and pointed in coloured cement to match the colour of tiles over and including screed bed or bedding layer of 15mm thick in cement mortar 1:6, complete all as specified and directed. |
| 114 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed. |
| 115 | Preparation of new plastered surfaces of walls and applying two coat of cement base paint (any colour) over chalk whiting, complete all as specified |
| 116 | Preparation of old decorated surfaces of walls and applying one coat of cement base paint (any colour) over chalk whiting, complete all as specified |
| 117 | Two coats of synthetic enamel paint over priming coat on new stone and concrete surfaces of any description not otherwise described over 10 cm width or girth including preparation of new surfaces complete all as specified |
| 118 | 3mm thick aluminium composite panel sheet (ACP) fixed with aluminium beading with rubber gasket including all necessary clips and fittings colour as approved by Engr-in-Charge all as specified and directed. |
| 119 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed. |
| 120 | Material and labour for point wiring with approved colour code multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade, two run of single core cable for phase & neutral and one run of single core multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade for earth continuity conductor to common earth and connected to earth dolly in and including new concealed PVC conduit terminated on and including new modular sunken box and suitable size of frame, cover for mounting switch, socket and regulator fixed on surface flush with wall , comprising of One light /bell/buzzer point controlled by one switch or one fan point controlled by one switch &fan regulator, complete all as specified and directed. Note : Unit rate is inclusive of making good the disturbed surfaces by provding by wall putty/POP after mason work and finshing to match the original and nothing extra shall be paid on this account. Note :Unit rate is inclusive of cutting chases in wall /foor/PCC and making good the disturbed surfaces to match the original and nothing extra shall be paid on this account. |
| 121 | All as per serial item 122 herein before but for socket outlet 3 pin 5 Amps on same board complete all as specified and directed |
| 122 | All as per serial item 122 herein before but for socket outlet 3 pin 6 Amps on independent board complete all as specified and directed |
| 123 | All as per serial item 122 herein before but One socket outlet three pin ,6/16 Amp, independent board, with 2.5 Sqmm (nominal area ) FRLSH cable & 2.5 Sqmm (nominal area ) cable as earth continuity conductor |
| 124 | Switch modular type (ISI marked), single pole, one way 6 Amps, one module (ISI marked), complete all as specified & directed. |
| 125 | Switch modular type (ISI marked), single pole, one way 16 Amps, one module (ISI marked), complete all as specified & directed. |
| 126 | Socket shutters outlet 2/3 pin 6 Amp modular type multi purpose two module (ISI marked), complete all as specified & directed. |
| 127 | Socket shutters outlet 2 in 1 pin 6/16 Amp modular type multi purpose combined 2 module (ISI marked), complete all as specified & directed. |
| 128 | Modular switch type stepped fan regulator, single pole, 230 volt two module complete all as specified and directed. |
| 129 | Ceiling rose, PVC or polycarbonate of size 65mmx50mm three terminals (ISI marked) all as specified and directed by Engineer-in-charge. |
| 130 | Disconnecting the power supply and taking down carefully by unscrewing from boards fittings and fixtures such as DBs, Junction Box, Panels of any size complete with all MCCB's ,MCB's etc and removing from site, Complete all as specified and directed . |
| 131 | MCB DB, IP 43 protection, powder coated double door with locking arrangement suitable for surface and flush mounting, 08 way SPN with 200 Amps busbar 240V completed all as specified and directed. |
| 132 | MCB, SPN , 240 volt, 40 to 63Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed |
| 133 | MCB ,SP , 240 volt, 6Amps to 32Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed |
| 134 | LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, fixed as in repair complete all as specified and directed. |
| 135 | Slim LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete fixed as in repair complete all as specified and directed. |
| 136 | LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size fixed as in repair complete all as specified and directed. |
| 137 | flexible LED strip with optimum brightness and uniformity of light for perfect cove lighting IP 20 complete with connection of two core copper wire complete all as specified and directed. |
| 138 | Taking down carefully old copper or aluminium sub main wiring of any Nos of wiring and size with earth wire on wooden batten/ surface conduit/ casing- capping complete with its all accessories and making good disturbed surfaces of wall , floors etc complete all as specified and directed. |
| 139 | Sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with copper conductor of size 6 Sqmm (nominal area), 1100 Volt grade(with approved colour coding as per IS) with and including continuous earth wire of size 6 Sqmm PVC insulated and unsheathed FRLSH multi stranded copper conductor 1100 volts grade , and connected to main board drawing through PVC concealed conduit 25mm size(minimum size), cutting chases in walls for PVC concealed conduit and making good the disturbed surfaces by providing by wall putty/POP after mason work and finshing to match the original surfaces and nothing extra shall be paid on this account all as specified and directed. Note : (i) For the purpose of measurement, 2 single core of 6 sqmm and one single core earth cable of 6 sqmm cable shall be considered as 1 running metre. (ii) colour code shall be Red for phase, Black for neutral and green for earth |
| 140 | LED panel surfance mounted ultra slim 2'x2' - 36 watts ultra slim (cool day) ceiling light, aluminum extruded housing with milky diffuser, heat exchanger unit, LED driver, surge protection complete suitable for perfect lighting cutting hole of required size in POP/false ceiling making good disturbed including taking down any type ceiling fitting complee all as specified and directed. |
| 141 | Round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size, fixed as in repair complete all as specified and directed. |
| 142 | ABS plastic1800W White Crescent Wall Mounting hand dryer machine (ISI Marked) suitable for bathroom compelte all as specified and directed. |
| 143 | LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete, including taking down old street lght complete all as specified and directed. |
| 144 | Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm and provision of flexible copper cable 3 core from ceiling rose to exhaust fan complete all as specified and directed. |
| 145 | Earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6mm buried directly in ground vertically to a depth not less than 2.25 meter below normal ground level (with top edge of earth plate not less than 1.5 meter below ground level) connected to galvanized iron earth lead wire 4mm dia, (main earthing lead ) by means of galvanized bolts, nuts and washers all as shown in electrical plate no 5 of MES Schedule Part-I (1991) with connected to earth test point & to main switch board with & including adequate quantity of charcoal dust and common salt alround earth plate & 15 mm dia GI pipe light grade for earth lead protection pipe for suitable length and GI pipe 20 mm dia light grade for watering pipe with funnel & wire mesh including necessary earth work and PCC (1: 3 : 6) type C-1 for earth pit and 40 mm thick pre-cast RCC cover in 1 : 2 : 4 type B1 with 3 Nos 8 mm dia TMT bars both ways with lift hook made out of 8mm dia bar including dismantling of old eathing set complete all as specified & directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 19, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysJul 13, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender