Tender For special Repair Of Brigade Magazine Building Number P-32 And Bldg No 113 Security Officer For B/R And E/M At 505 Abw And Other Sanction Work Under Ge (North) Delhi Cantt-10
Tender Value
42.09 Lakhs
Estimated cost
Bid Submission
10 Jul 2026
4 days left
EMD
84500
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
New Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair Of Brigade Magazine Building Number P-32 And Bldg No 113 Security Officer For B/R And E/M At 505 Abw And Other Sanction Work Under Ge (North) Delhi Cantt-10
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling of brick tiles, terracing tiles, single layer from roof laid, bedded and pointed in any mortar all as specified & directed. |
| 2 | Removal of Mud from top roof slab, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and directed. |
| 3 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc 1.50 sqm each and removing from site, complete all as specified and directed. |
| 4 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm eachand n exc 4 sqm and removing from site,complete all as specified and directed. |
| 5 | Demolition of brick work built in cement mortar including all quions, arcches, pillars etc complete all as specified and as directed. |
| 6 | Taking down cement plaster on brick or concrete surfaces, parapets including raking out joint, hacking for key, scrubbing down with water, at any description with necessary scaffolding of any height, etc complete all as specified and as directed. |
| 7 | Demolition of cement concrete including floor tiles or stone in any description and any position etc removal from site up to 500 m complete all as specified and directed |
| 8 | Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing), and rubbish off the premises complete all as specified and directed. |
| 9 | M&L cutting crack to 'V' groove section in existing roof cleaning out wetting grouting with cement and sand slurry of 1:3 complete all as specified and directed. |
| 10 | M&L Plain cement concrete type B1 (1:2:4) using 20mm graded stone aggregate as in levelling course and other works as in roof, kerb, coping, padding etc complete all as specified and as directed. |
| 11 | M&L for rendering 10mm thick in CM 1:4 on roof suraces with liquid water proofing compound @ 200 ml per bag finished even and smooth without using extra cement complete all as specified and directed. |
| 12 | M&L for water proofing treatment to non accessible roof and edges (vertical or tapered) / sumken portion etc. in following sequence:- (i) Properly cleaning and drying the surface (ii) Applying a coat of bitumen primer @ 1.2Kg/Sqm and primer shall be allowed to dry over night. (iii) Laying APP based modified water proofing membrane of weight not less than 3kg per sqm and thickness not less than 3 mm, with 100mm overlaps, sealed and bonded to the surface by 'torchon' method (iv) Applying two coat of bituminous based aluminum painting @ 0.15 kg/Sqm each coat on water proofing treatment with preparation of surfaces complete all as specified and directed at site. |
| 13 | M&L brick work in CM ( 1:4 ) with using sub class `B ` modular brick straight or curved on plan exceeding 6.0mtr mean radius complete all as specified and directed. |
| 14 | M&L for providing rust proof /anti corrosive treatment to bars :-(i) cleaning of all exposed bars (new & old) alround(ii) Apply a single coat of Alkaline rust converting primer on alround bars new & old as recommended by the manufactuer(iii) Apply two coats of Epoxy phenolic anti corrosive protective coat on bars alround new & old as recommended by the manufactuer. Note : Anti corrosive treatment shall be continuous espcially in the regions where pitting, imperfections, etc were present on the surface of the bars. It is important that the rear portions of re bars (those towards the concrete substrate) should not be left without coating. |
| 15 | M&L for providing PMM (Polymer modified cementitious mortar) :-(i) Dry sub strate surface and free of debris & dust(ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes).(iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness.Note:- Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use.(iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed. Please Enable Macros to View BoQ information |
| 16 | M&L for providing PMM (Polymer modified cementitious mortar) :-(i) Dry sub strate surface and free of debris & dust(ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes).(iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness.Note:- Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use.(iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 19, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 10, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysJul 13, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender