|
| 1 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, Pole, Laying UG cable etc. and n exc 1.5 m in depth and getting out soft/loose soil complete all as specified and as directed. |
| 2 | Returning, filling in, including spreading, levelling, watering and well ramming in layer not exceeding 25 cm thick in soft/loose soil complete all as specified and as directed. |
| 3 | Removing excavated material (soils) not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed. |
| 4 | M&L providing river sand (washed and screened) cushioning for protection of UG cable (8cm deep before laying & 15cm above the top of cable after laying in trenches with dry sand of approved quality including fillling, spreading and pulling down to desired thickness complete all as specified and as directed.Note: (Punned take of 18cm only shall be considered for payment purpose). |
| 5 | Supply and laying sub class B bricks available best quality brick in trenches for protection of UG cable with width equal to length of bricks laid dry and flat complete all as specified and as directed. |
| 6 | Laying only old burnt old size bricks, straight or curved on plan, laid flat with width equal to length of brick, laid dry over electric cable for protection complete all as specified and as directed.Note: old serviceable brick obtained shall be reused. |
| 7 | M&L horizontal boring of holes, under road/ pavement / hard standing etc. not exceeding 10 Meters in length, in any type of soil, suitable for passing through up to 50 mm bore, galvanised steel tubing complete all as specified and as directed.Notes :-(a) Pipe shall be measured and paid separately under relevant item of this schedule.b) Removal of surplus soil shall be deemed to be included in the Unit Rate. |
| 8 | S&F Galvanised mild steel pipe/tubing, light grade complete with all fittings of 50 mm bore dia, laid in trenches / under roads, fixed to poles/ walls with Mild steel clamps, bolts, nuts and washers as in cable protection complete all as specified and as directed. |
| 9 | Disconnecting & taking out defective under ground LT cable from trenches, pole, pipe, floor, wall etc including bricks, Gl pipes and removing from work site of unserviceable material and keep serviceable material for reuse in safe custody for any size complete all as specified and as directed.Note: Excavation/earth work shall be measured & paid separately under relevant item of this schedule) |
| 10 | Supply, laying, jointing and testing LT underground electric power cable crossed linked XLPE insulated, two or more core galvanized steel strip or wire armored / PVC insulated armored cable heavy duty electric cable with aluminium conductor 1100 volts grade, cross-sectional area 16 sqmm 4 core laid in trenches / laid under floor or fixed to walls/on poles / in ducts or passing through pipes etc fixing and connecting accessories such as Aluminium cable lugs, cable glands, nut, bolts, washers etc complete all as specified and as directed.Note: Earth work, excavation, Gl pipe, sand cushioning and protection brick shall be measured and paid separately under appropriate items. |
| 11 | Supply, laying, jointing and testing LT underground electric power cable crossed linked XLPE insulated, two or more core galvanized steel strip or wire armored / PVC insulated armored cable heavy duty electric cable with aluminium conductor 1100 volts grade, cross-sectional area 10 sqmm 4 core laid in trenches / laid under floor or fixed to walls/on poles / in ducts or passing through pipes etc fixing and connecting accessories such as Aluminium cable lugs, cable glands, nut, bolts, washers etc complete all as specified and as directed.Note: Earth work, excavation, Gl pipe, sand cushioning and protection brick shall be measured and paid separately under appropriate items. |
| 12 | Relaying in trenches or passing through pipe, 1100 volts grade, LT electric power UG cables, of any type/Size with and including all fixing & connecting accessories such as Alluminium cable lugs, cable gland, nut, bolts, washer etc complete as specified and as directed.Note: The Excavation and earth work shall be mesured and paid separately under relevant item of Schedule. |
| 13 | M&L LED street light epoxy powder coated pressure die-cast aluminium housing with weatherproof gasket for LEDs with lens and control gear compartments, pressure die-cast aluminium frame with heat resistant toughened clear glass fixed with SS screws, input voltage 140-270 Volts, delivering lumen equal to/greater than 4500 lumen, system wattage 45 Watt, Ingress protection IP-66 with all accessories including taking down unserviceable light fitting and removing from site complete all as specified and as directed. |
| 14 | M&L LED street light epoxy powder coated pressure die-cast aluminium housing with weatherproof gasket for LEDs with lens and control gear compartments, pressure die-cast aluminium frame with heat resistant toughened clear glass fixed with SS screws, input voltage 140-270 Volts, delivering lumen equal to/greater than 6000 lumen, system wattage 60 Watt, Ingress protection IP-66 with all accessories including taking down unserviceable light fitting and removing from site complete all as specified and as directed. |
| 15 | M&L LED street light epoxy powder coated pressure die-cast aluminium housing with weatherproof gasket for LEDs with lens and control gear compartments, pressure die-cast aluminium frame with heat resistant toughened clear glass fixed with SS screws, input voltage 140-270 Volts, delivering lumen equal to/greater than 9000 lumen, system wattage 90 Watt, Ingress protection IP-66 with all accessories including taking down unserviceable light fitting and removing from site complete all as specified and as directed |
| 16 | M&L LED flood light epoxy powder coated pressure die-cast aluminium housing with weatherproof gasket for LEDs with lens and control gear compartments, pressure die-cast aluminium frame with heat resistant toughened clear glass fixed with SS screws, input voltage 140-270 Volts, delivering lumen equal to/greater than 10000 lumen, system wattage 100 Watt, Ingress protection IP-66 with all accessories including taking down unserviceable light fitting and removing from site complete all as specified and as directed. |
| 17 | M&L LED flood light epoxy powder coated pressure die-cast aluminium housing with weatherproof gasket for LEDs with lens and control gear compartments, pressure die-cast aluminium frame with heat resistant toughened clear glass fixed with SS screws, input voltage 140-270 Volts, delivering lumen equal to/greater than 20000 lumen, system wattage 200 Watt, Ingress protection IP-66 with all accessories including taking down unserviceable light fitting and removing from site complete all as specified and as directed. |
| 18 | Digging out incoming and outgoing cables of any sizes from loops near junction box/ feeder pilar box in trenches, cutting burnt out uninsulated portion of cable and relaying /refixing in trenches & returning, refilling the excavated soil and connecting the cables with bus bars including provision of suitable size of aluminium lugs complete all as specified and as directed. Note:- The excavation and earth work shall be included in the item itself. Contractor shall quote the rate accordingly. |
| 19 | S&F loop in- loop out fuse junction box of internal dimention 250 x 200 x 100mm made of FRP sheet with weather proof canopy and locking screw fitted with and including 50 Amp rated 4 way connectors for 3 phase and neutral incoming/outgoing. mounted in the box, fixing on street pole/rail poles including necessary aluminium clamps, suitable glands, lugs and Gl nut and bolt and 01 SP of 6 Amp for controlling including taking down old unserviceable junction box all as specified and as directed.(Note: Contractor shall provide cable lugs and PVC gland of suitable size if required on site for connecting cable in junction box). |
| 20 | S&F In repair single run 3 core, 2.50 sqmm nominal cross sectional area multistranded copper conductor cable, over all PVC sheathed, 1100 Volts grade confirming to IS-694-2010 (FRLS) heavy duty cable PVC insulated and PVC sheathed from pole junction box to light fitting complete all as specified and as directed |
| 21 | 20 mm nominal bore dia, UPVC pipes of pressure rating 06 kg/cm2 fixed to pole, any type including provision MS clamp of size 20mm x 3mm flat at interval of 1.5 m length complete all as specified and as directed. |
| 22 | S&F in repair power contractor 40 amps 3 pole (1NO+1NC), 415 Volts AC 50Hz, including connecting with existing system complete all as specified and as directed. |
| 23 | S&F in repair of Astronomical Digital Time switch (5-40) Amps, 240 Volts, AC, Singlephase complete all as specified and as directed. |
| 24 | M&L disconnection of all electric connection and taking down of street light fittings of any type, size, capacity and model removing of unserviceable spares or accessories for repair/ replacement of the same including reconnecting and refixing of street light to its existing position viz pole / high mast and testing complete all as specified and as directed. |
| 25 | S&F repair Electronic driver suitable for 60 Watts LED Street light fittings of approved make / brand complete all as specified and as directed. |
| 26 | S&F MCB TPN 63 Amps, 'C' series 10kA, 415 Volts and to be housed in DBs complete including necessry connection all as specified and directed.Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating). |
| 27 | Supply, installation and testing of outdoor Time line distribution board for street light, degree of protection IP 54, three phase, maximum load 12 kW, prewired with Digital timer switch, contactor TP rating 65 Amp and MCB Tripple pole & neutral rating 63 Amp, complete all as specified and as directed. |
| 28 | Material and labour for steel tubular poles complete with cast iron base palate, final taper plug bolts, nuts & screws as specified type 410 SP-31, 9.0 meter long including painting all external exposed steel surfaces with two coats of aluminum paints over a coat of red oxide zinc chrome primer and all internal surfaces and external surfaces in contact with concrete with two coats of black bituminous paint including taking down old existing concrete poles / struts any size after demolition of foundation and removing debries of the site complete all as specified and as directed. |
| 29 | M&L cement concrete (1:3:6) type C-2 using 40mm graded stone aggregate for foundation of stay assembly/struts/pole etc. (around the poles in pit) complete all as specified and as directed. |
| 30 | M&L PCC (1:3:6) type C-1 using 20mm graded stone aggregate for coping / pedestal of poles including necessary form work, fair finishing to exposed surfaces by using extra cement complete all as specified and as directed. |
| 31 | M&L for painting to the LT PCC poles (surface area exc. 5 Sqm & not exc. 5.7 Sqm) with strips in alternate bottom to top with three strip of black synthetic paint & two strip of yellow/sky blue paint (as per existing pattern) throughout the circumference of pole including one coat of white wash on PCC coping of pole, two coat of white cement base paint on pole and two coat of aluminium paint to channel, cross arm, clamp and pipe fixed/mounted on pole after scraching out old paint, cleaning and making existing surface rust free, preparation of the existing surface, including marking pole numbers in a 15cm dia yellow circle with number writing black synthetic paint/sticker complete all as specified and as directed. |
| 32 | M & L painting of steel pole (swan neck type or straight type) up to 10 mtr height with cross arms, clamp of any length and shape for LT overhead line/ for street light with two coat of aluminium paint after scratching out old paint, cleaning and exiting surface rust free, preparation of the existing surface, including marking pole numbers in a 15 cm dia yellow circle with number writing with black synethic paint/ Sticker, including painting strips in alternate from bottom to top with three strips of black synthetic paint & two strips of Yellow/ Red paint (as per existing pattern through out the circumference of pole, including removing extra wall papdi (dampness), peel off wall papdi by sand paper and making good with putty as per existing thickness and applying one coat of white washing on PCC copping of pole and re-numbering of pole with approved size of letter (Example P-001) with synthetic enamel paint of white colour background and black colour lettering complete all as specified and as directed. |
| 33 | M&L earthing complete with galvanized steel plate electrodes of size600x600x6mm thick buried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised wire 4.00 mm earth lead by means of nuts, bolts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No-3 of SSR Part-I including necessary excavation and earth work, PCC 1:3:6 type C-1 with 50mm thick pre-cast RCC cover 1:2:4 type B-1 cover slab reinforced with 8 mm dia TMT bar @ 15cm C/C both ways with suitable handle of 10mm dia MS rod including providing charcoal or coke & common salt in alternate layer of 15cm compacted thickness all around the earth electrode with funnel and 20mm bore (light grade Gl watering pipe wire mesh, aluminium lugs complete in all respect GI earth wire protected by 15mm bore Gl pipe and other end connected with main switch/ earth test pont, including dismantling old unserviceable earth pit complete all as specified and as directed. |
| 34 | M&L for cross arms, bracing, support, clamps and back plates fabricated from structural steel section including nuts, bolts, washer, welding bending cold or hot drilling holes for bolts in any shape or size as indicated or directed including Gl clamp and including of one primer coat, one under coat and one finishing coat of synthetic enamel paint complete all as specified and as directed. Please Enable Macros to View BoQ information |
