|
| 1 | Surface dressing of the ground including removing vegitation and in equalities not exceeding 15cm deep and disposal of rubbish lead up to 50 metres and lift up to 1.5 metres |
| 2 | Earth work excavation in foundation trenches or drains not exceeding 1.5m in width or 10 sq.m on plan including dressing of sides and ramming of bottoms, lift upto 1.5m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m. |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc layers not exceeding 20cm in depth consolidating each deposited layers by ramming and watering lead up to 50 mtr and lift up to 1.5 metres |
| 4 | Providing and laying cement concrete 1:4:8 (1 cement 4 M Sand 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering and reinforcement for foundation and plinth |
| 5 | Providing and laying cement concrete 1:5:10 (1 cement 5 M Sand 10 graded stone aggregate 20mm nominal size) excluding the cost of centring and shuttering and reinforcement for foundation and plinth |
| 6 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 M sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) |
| 7 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3(1 cement, 1.50 M.sand, 3 granite chips 20mm nomnal size) |
| 8 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3(1 cement, 1.50 M.sand, 3 granite chips 20mm nomnal size) |
| 9 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 M.sand : 3 graded stone aggregate 20 mm nominal size ). |
| 10 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 11 | Providing and fixing precast cement concrete 1:1.5:3(1 cement :1.5 M.sand :3 graded stone aggregate 20mm nominal size)sety in position with cement mortar 1:2(1cement :2coarse sand )and finished smooth with 6mm thick cement plaster 1:3( 1 cemnet :3 Msand )on exposed surface including cenetering and shuttering. |
| 12 | Cold twisted steel reinforcement for R.C.C. work including bending, binding and placing in position complete. |
| 13 | Centring and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns, etc. for mass concrete |
| 14 | Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts |
| 15 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, girders, bressumers and cantilevers |
| 16 | Centering and shuttering including strutting propping up to floor five level and removal of form work for Stairs (Excluding Landings) except spiral staircases |
| 17 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform |
| 18 | Providing and laying factory made Precast concrete solid blocks of size 40X20X15 cm of grade M10 made of C&D waste from approved manufacturer in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 M sand) |
| 19 | Providing and laying factory made Precast concrete solid blocks of size 40X20X15 cm of grade of grade M10 made of C&D waste from approved manufacturer in superstructure above plinth level up to floor V level Cement mortar 1:6 (1 cement : 6 Msand) |
| 20 | Half brick masonry in super structure above plinth level upto floor five level cement mortar 1:4 ( 1 cement 4 Metal sand ) |
| 21 | Providing wood work in frames of doors, windows, clerestory windows and other frames wrought, framed and fixed in position-I class Karimaruthu or equivalent ( hold fast lugs or dasg fastener shall be paid for separately ) |
| 22 | Providing and fixing 35 mm thick panelled, glazed or panelled and glazed shutters for doors windows and clerestory windows including anodised aluminium butt hinges with necessary screws. First class Karimaruthu or equivalent ( Single/Double leef shutters) |
| 23 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. |
| 24 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 25 | Providing and fixing brass door latch with necessarys screws etc completea) Brass door latch 300x16x5 mm |
| 26 | Providing and fixing brass tower bolt (barral type with necessarys screws etc complete.250 mm x 10mm |
| 27 | Providing and fixing brass handle with necessarys screws etc complete.a) Brass Handle 125 mm |
| 28 | Providing and fixing Bright finished brass door stoper with rubber cusion & necessary screws |
| 29 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 30 | Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete 25 mm dia |
| 31 | Providing and fixing to existing door frames.30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5mm thick FRP laminate for panels confirming to TADS 6: 1993 and / or IS: 14856 - 2000 including fixing to frames. |
| 32 | Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. |
| 33 | 6 mm cement plaster of mix :1:3 (1 cement : 3 P sand) |
| 34 | 12 mm cement plaster of mix :1:6 (1 cement: 6 P.sand) |
| 35 | 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 M sand) |
| 36 | 15 mm cement plaster on the rough side of single or half brick wall of mix :1:6 (1 cement: 6 P sand) |
| 37 | Providing plaster drip course/groove in plastered surface for RCC projectiosn |
| 38 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 39 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Size of Tiles 600 x 600mm |
| 40 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble |
| 41 | Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 800x800 mm |
| 42 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work |
| 43 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre |
| 44 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two Coats or more |
| 45 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 46 | Painting room floors and pavilion floors /runway/taxi track/apron marking with adequate nos of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-in-charge, i/c cleaning the surface of ail dirt, scales, oil, grease and other foreign material etc. and lining out complete. New work (Two or more coats) |
| 47 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture |
| 48 | Finishing with Deluxe Multi surface Epoxy paint system for interiors and exteriors using Primer as per manufacturers specifications Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture |
| 49 | Providing and fixing stainless steel ( Grade 316) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 50 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required EPDM rubber/ Neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer- in-charge. (Glazing and panelling to be paid for separately) For Fixed Portion Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 51 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 52 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade 1 Type II in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with approved lamination on both sides |
| 53 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness ( Weight not less than 12.5 Kg/Sqm) |
| 54 | Providing and Fixing in required profile twin wall 4mm thick Lexan thermo clean of GE equivalent one side UV protected polycarbonate sheet in required colour and shade to the frame provided in MS tubular / GI Tubes/Aluminium sections. The Alcox section shall be rigidly fixed to the supporting structure with self taping self drilling SS screws fixed approx 150mm centre to centre. The joints of the structure shall be properly sealed with silicon sealants wherever required so as to make the fabricated structure totally water proof. The rate shall include the cost of all materials such as aluminium alcox sections set and channel, EPDM gasket, self taping screws, nuts bolts and silicon sealant and all labour and material required to cut, fabricate and fix the structure complete as per direction of Engineer in Charge (Cost of supporting structural framework provided shall be paid for separately). Finished sheet area shall be measured for the purpose of payment |
| 55 | ROLLING SHUTTER: Supplying and fixing rolling shutters of approved make, made of 80 mm x 1.25 mm M.S. laths with 1.25 mm thick top cover. M.S. laths shall be interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 -part 1 and M.S. top cover of required thickness for rolling shutters. |
| 56 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. |
| 57 | a) 15mm Nominal dia pipes |
| 58 | b) 20mm Nominal dia pipes |
| 59 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work |
| 60 | a) 15mm Nominal dia pipes |
| 61 | b) 20mm Nominal dia pipes |
| 62 | c) 32mm Nominal dia pipes |
| 63 | d) 40mm Nominal dia pipes |
| 64 | Providing and fixing nominal guage PVC Pipe of approved quality complete with special flang compression type fittings including trenching and re filling etc. External work. |
| 65 | a) 50 mm diameter pipes |
| 66 | b) 63 mm diameter pipes |
| 67 | c) 90 mm diameter pipes |
| 68 | d) 110 mm diameter pipes |
| 69 | Providing and fixing CPVC ball valve of approved quality and manufacture complete |
| 70 | a) 20mm Nominal Bore |
| 71 | b) 40mm Nominal Bore |
| 72 | Providing and fixing C.P. Brass bib cock of approved quality coforming to IS:8931. 15mm Nominal Bore (Cera/ Hindware/ Parryware/ Jaguar or equivalent ) |
| 73 | Providing and fixing C.P. Brass stop cock ( concealed ) of standard design and of approved quality coforming to IS :8931. 15 mm Nominal Bore (Cera/ Hindware/ Parryware/ Jaguar or equivalent ) |
| 74 | Providing and fixing CP brass Angle Valve of approved quality and manufacture complete. 15 mm Nominal Bore (Cera/ Hindware/ Parryware/ Jaguar or equivalent ) |
| 75 | Providing and fixing Health Faucet ABS Body with 1 meter SS raided connection Pipe of approved quality and manufacture complete. (Cera/ Hindware/ Parryware/ Jaguar or equivalent ) |
| 76 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 77 | Providing and fixing C P Brass Shower Rose with 15 or 20 mm 300mm long shower arm inlet and flanges (Cera/ Hindware/ Parryware/ Jaguar or equivalent ) |
| 78 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 79 | Providing and fixing towel rail brackets fixed to wooden cleat with screws and washers. a)600x20mm C.P brass towel rail with brackets. 600mm long towel rail brackets with total length of 645mm width 78mm and effective height of 88mm weighing not less than 190gms (Cera/ Hindware/ Parryware/ Jaguar or equivalent ) |
| 80 | Providing and fixing 600x450mm mirror of superior glass(approved quality) fixed to walls with SS Studs including all fittings complete (Cera/ Hindware/ Parryware/ Jaguar or equivalent ) |
| 81 | Providing and Fixing CP Brass liquid soap container109 mm wide,125 mm high and 112 mm distance from wall of standard shape with bracketsof the same materials withsnap fittings of approved quality and colour,weighing not less than 105 gms (Cera/ Hindware/ Parryware/ Jaguar or equivalent ) |
| 82 | Providing and fixing CP Brass grating of approved quality and colour. Rectangular type with openable circular lid. 150 mm nominal size square 100 mm diameter of the inner hinged round grating (Cera/ Hindware/ Parryware/ Jaguar or equivalent ) |
| 83 | Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. (Cera/ Hindware/ Parryware/ Jaguar or equivalent ) |
| 84 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap and Half pedestal (Cera/ Hindware/ Parryware/ Jaguar or equivalent ) |
| 85 | Providing and placing on terrace at floor level Polythene water storage tank ISI:12701 marked with cover and suitable locking arrangement and making necessery holes for inlet, outlet an over flow pipe but without fittings and the base support for tank.(a) 1000 liter capacity circular or rectangular shaped tanks as per the direction of the Engineer In Charge (Sintex/ Ocean/Aquatech) |
| 86 | Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction and of approved size and design/ shape laid in required colour and pattern over and including 50mm thick compacted bed of Fine sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. |
| 87 | Painting name board on the wall surface with waterproof and weatherproof Arcylic wall paint of approved quality and manufacture as per the direction of the Engineer In Charge |
| 88 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group A |
| 89 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch connections etc. as required. |
| 90 | Wiring for light/ fan/circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 91 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit along with 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 92 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 93 | (a) 5/6 A switch |
| 94 | (b) 3 pin 5/6 A socket outlet |
| 95 | (c) 16 A Switch |
| 96 | (d) 32 Amps Switch |
| 97 | Supplying and fixing brass batten/ angle holder including connection etc. as required |
| 98 | Supplying and fixing 3pin, 5A cealing rose on the existing junction box/ wooden block including connections etc. as required. |
| 99 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. |
| 100 | Supplying of LED Tubelight set 20w 1800 lumen 4 feet |
| 101 | Supplying of LED Lamp 9watts |
| 102 | Supplying of PVC Bulkhead with Suitable LED bulb |
| 103 | Providing and erectingfresh air fan 250 mm dia with square frame make of ABS body with louvers Cat.III |
| 104 | Supplying and erecting waterproof LED street light/flood light fittings with High power White LED,s wattage of 250 Watt and above assembled on single MCPCB,efficiency more than 130 m/w and corrosion free high pressure die cast aluminium housing with smooth finish powder coated and heat sink extruded aluminium with diffuser and polycarbonate optics/lenses with company mark/name engrave or embosees 120 to 300 V power Factor morethan0.95,THD<10% CCT 5000 K uniformity ration >0.45,Luminaire efficiency >85 CREE/OSRAM/Philips Lumileds/NICHIA/ SEOUL/ Bridge Lux (USA) make LED used for luminaire (Each fittings requred LM79 M& LM 80 certificates) (A) Street light (IP-65).Surge-4KV(e) above 48 to 60Watt |
| 105 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 106 | (a) 6 Amps Single pole and neutral |
| 107 | (b) 10 Amps Single pole and neutral |
| 108 | (c) 16Amps Single pole and neutral |
| 109 | (d) 6 Amps Tripple pole and neutral |
| 110 | (e) 10 Amps Tripple pole and neutral |
| 111 | (f) 16Amps Tripple pole and neutral |
| 112 | Supplying and fixing following rating, double pole, (single phaseand neutral), 240 V, residual current circuit breaker (RCCB),having a sensitivity current 30 mA in the existing MCB DBcomplete with connections, testing and commissioning etc. as required. 40 A |
| 113 | Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) |
| 114 | (a) 6 way , Double door |
| 115 | (b) 8 way (4 + 24), Double door |
| 116 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt ) as required. |
| 117 | Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required. |
| 118 | CHANGE-OVER SWITCH- Supply and installation of 100A 4P on-load changeover switch in sheet steel enclosure on wall mounting angle iron frame work and including top & bottom cable boxes to receive incoming & outgoing cables. Please Enable Macros to View BoQ information |
