Tender For Provision Of One Walk In Cold Room At 92 Bh At Bb Cantt, Srinagar.
Tender Value
21.19 Lakhs
Estimated cost
Bid Submission
14 Jul 2026
3 days left
EMD
42380
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
srinagar → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Provision Of One Walk In Cold Room At 92 Bh At Bb Cantt, Srinagar.
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 03-Jul-2026 | Corrigendum for revised BOQ and Particular specification | BOQ | 14-Jul-2026 |
| 2 | 03-Jul-2026 | Corrigendum for revised Date | Date | 14-Jul-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Taking down frame with shutters (without taking off shutters from frame) exc 1.5 sqm but n.exc 4 sqm each, complete all as specified and directed. |
| 2 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for, Door frame and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws,all as per architectural drawings, complete all as specified and directed. |
| 3 | M&L for 12 mm thick prelaminated particle board exterior grade,prelaminated both sides with decorative choice laminaions fixed with EPDM rubber /neoprene gasket etc to aluminium frame in lower pane, complete all as specified and directed |
| 4 | S&F 5.5mm thick Sheet glass,ordinary quality and glazing fiexed to Aluminiu Partition with required EPDM rubber/neoprene gasket etc n exc 0.5 sq. m in each pane in upper portion, complete all as specified and directed. |
| 5 | S & F of Powder coated aluminium of any colour (Thickness of powder coating not less than 50 micron ) anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including providing and fixing hinges/pivots and making provision for fixing of fittings whereever required ,necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as door stopper double leged (1 No.). hinges type B-21 125mm long (3 Nos.) suitable handles 2 Nos including Mortice lock arrangment and frosted glass 5.5mm thk in upper panel and 12mm thick Prelaminated decorated on both face Particle board sheet in lower Panel .) for each shutter, complete all as specified and as directed. |
| 6 | M&L for brickwork with old sized subclass 'B' bricks straight or curved on plan exc 6m mean radius and built in CM 1:6 etc including demolition of brick work, complete all as specified and directed. |
| 7 | M&L for glazed ceramic coloured tiles of size not exceeding 450x350x7mm or 350x250 x7mm thick as skirting/dado, wall, on vertical surface etc . ,set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile with and including 10mm thick backing coat in CM 1:4 (if reqd in any portion), including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) etc. removing rubbish off the premises, complete all as specified and directed. |
| 8 | M & L for rendering 15mm thick cement plaster in CM (1:4) on brick work or concrete surfaces finished even and fair without using, extra cement all as specified and directed. |
| 9 | M&L for preparation of new plastered surfaces of walls and applying two coats of cement based paint over a coat of primer, complete all as specified and directed. |
| 10 | M & L for complete removal of existing paint on old surface of wall/ceiling and p apply one coats of oil bound distemper, complete all specified and directed. |
| 11 | Demolition of Cement Concrete (reinforced) of any description and in any position not otherwise specifically provided for, complete all as specified and directed. |
| 12 | Excavating in post holes each n.exc 0.5 cum getting out in soft/loose soil and removing surplus soil to a distance n.exc 50 m and making good surface complete.all as specified and directed |
| 13 | M & L for plain cement concrete 1:4:8 Type D-2 (using 40mm graded crushed stone aggregate) 75mm thick, as in sub base over rammed earth, complete all as specified and as directed. |
| 14 | M&L for plain cement concrete 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) 40mm thick, as in flooring, rough finished, complete all as specified and directed. |
| 15 | M & L for plain cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in post/strut foundation, complete all as specified and directed. |
| 16 | S & F mild roof structural steel angles/rectangular hollow section/steel tubular roof trusses (framed), purlines and fastening including distance pieces etc., complete all as specified and directed. |
| 17 | S&F for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws, complete all as specified and directed |
| 18 | M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enameled paint over a coat of red oxide primer, complete all as specified and directed. |
| 19 | M&L 6mm thick Non Asbestos fibre cement /Pre Laminated self embosssed texture designer board E-Board classic size 595x595mm, HPSC (High pressure steam cured) to be fixed or inserted to pre laminated GI frame work for seamless ceiling size 600mm x 600mm with main runner 38x24x0.9mm thick, cross tee 8.6x24x0.9mm and wall angle 19x19x0.9mm duly suspended with 2mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip, complete all as specified and directed. |
| 20 | M & L for cutting, bending, welding cold or hot incl drilling, jointing, assembly and making different type/size as req shape and size of fitting and fixture any other desc shape as per user req or all as decided, specified and directed by EIC with making shape of multipurpose and multi storey type cabin of rack shape shelves like vertical colns/tiers/shelves based type with help of providing and fixing stainless steel grade 304 rack, channels, plates, solid plate sheet, cross arms, angle,m channel or any type/ size of stainless steel grade 304 etc incl welding, grinding, buffing, polishing and make curvatures and fitting the same with stainless steel nuts and bolts complete incl fixing the shelves with necessary accessories & stainless steel fasteners, bolts etc of req size on the shelves or the side of waist slab along with providibng suitable arrangement for fabricated structural steel sections of rack work for use inside a walk-in-cold room as designed for blood storage system, complete all as specified and directed. |
| 21 | Supply, fixing, installation, testing and commissioning of Walk - in cold room of two chambers ,Freezer Room of size 8'x8'x8' consisting of wall & ceiling panel made out of PGI sheet filled with 120 mm PUF insulation, and Ante Room of size 5'x5'x8' consisting of wall and ceiling panel made out of PGI sheet filled with 60 mm PUF insulation, for Blood Bank and other low temperature application along with anti skid GI flooring on 60 mm PUF, door of suitable dimension,hydraulic door closer, digital temperature indicator, Air cooled low temperature split unit of 2 HP rating with twin cooling system (one working and one stand by cooling unit) compltete unit system having Reciprocating/Scroll Compressors working on R - 22/R - 410a refrigerants to maintain temperature of 4+/- 2 degree Centigrade at an ambient temperature of 30 degree centigrade complete job all as specified ,decided and all direction by Engr In Charge. Please Enable Macros to View BoQ information |
| 22 | Supply, fixing, installation, testing and commissioning of Walk - in cold room of two chambers ,Freezer Room of size 8'x8'x8' consisting of wall & ceiling panel made out of PGI sheet filled with 120 mm PUF insulation, and Ante Room of size 5'x5'x8' consisting of wall and ceiling panel made out of PGI sheet filled with 60 mm PUF insulation, for Blood Bank and other low temperature application along with anti skid GI flooring on 60 mm PUF, door of suitable dimension,hydraulic door closer, digital temperature indicator, Air cooled low temperature split unit of 2 HP rating with twin cooling system (one working and one stand by cooling unit) compltete unit system having Reciprocating/Scroll Compressors working on R - 22/R - 410a refrigerants to maintain temperature of 4+/- 2 degree Centigrade at an ambient temperature of 30 degree centigrade complete job all as specified ,decided and all direction by Engr In Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 03, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Jul 14, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 3 days
Jul 14, 2026
18:00 IST
Corrigendum-2 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 3 daysJul 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender