|
| 1 | S&F following sizes (dia.) of ISI marked MMS ( IS:9537 P - III ) PVC conduit along with ISI marked (IS:3419-1988) accessories as required in recess including making jhiri in the wall,clamps at suitable spacing, covering conduit and making good the same as required. |
| 2 | 25 mm |
| 3 | S&F following sizes of ISI marked ( IS:14927 P - II ) uPVC trunking along with accessories like coupler, inner, outer, elbow, square box, tee, end cap etc. on surface with screws, expansion fasteners etc. as required. |
| 4 | 38 mm x 25 mm |
| 5 | Supply and laying PVC Insulated and PVC Round Sheathed Multi Core copper conductor (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing pipe / open trench / Cable tray / on surface including making connection etc. as required. |
| 6 | 1.5 sq.mm x 3 core |
| 7 | Supply, Drawing and Testing of 4 pair, 23 AWG Solid Bare Copper wire insulated with PVC, U/UTP (Unscreened/Unshielded Twisted Pair), Category 6, Class E, 100 Ohm Impedance, Indoor Cable as per latest ammendments of ANSI/TIA/EIA-568 , The copper conductors should be balanced twisted in pairs, seperated by a cross-member fluted pair divider & protected by LSZH Jacket. Certified performance in a 4-connector configuration upto 100 Mtrs channel requirements & transmission frequencies ranging from 250 to 500 Mhz. in existing MS/PVC Conduits/casing capping including making connections to Information outlets and Patch Panels with jack & ferruling at both ends for identification with necessary tools for punching, stripping, crimping and testing etc as required complete in all respect. |
| 8 | Supply and Installation of unshielded/360 degree shielded PCB based Information outlets made of high impact plastic body with ABS, Flammability rating UL 94 V-0 with provision for protection against dust in jack or Faceplate, suitable for Cat 6/6A application complying to latest amendments, According. to Cat. 6/6A channel, It should support channel as well as components requirements of Cat 6/6A standards at frequencies 250/ 500 MHz. Cat 6/6A unshielded/shielded Jack should be suitable to terminate 4 pair, 23/24 AWG solid/stranded wire diameters, using 100 Ohm unshielded/shielded balance twisted pair cable, the jack should have toolless/impact termination on reliable copper tin plated Insulation displacement contact, with easy lock mechanism, It supports IEC 60603-7-4 and complied with ANSI/TIA 568 C.2 & ISO/IEC 11801 or latest standard. jack should be RJ11,RJ12 & RJ45 compatible. Should support Ethernet 1.2 Gb/s ATM,Digital video and broadband/baseband analog video, Voice over internet protocol (VOIP) Specifications in existing modular/MS Boxes along with necessary connections as required. All as per pre approved by Engineer in charge. |
| 9 | Cat 6, Un-sheilded Information Outlet |
| 10 | Supply & fixing of square Faceplate for Flush / Surface Mount Information Outlets Single/Dual or Quad Aperture with dust cover, material should be High-impact, flame retardant, thermoplastic, UL listed material, Suitable for RJ45 unshielded/shielded connection modules. Should match with I. O. OEM. Dimensions should be 86mm X 86mm as required complete in all respect. All as per pre approved by Engineer in charge. |
| 11 | Single Aperture |
| 12 | Supply, Installation, Testing and Commissioning of Rack mounted 19\\" 1U, 24 Port loaded, CRS chasis, powder coated, sheet steel, High-impact, flame retardant, thermoplastic, UL Listed, Modular Patch Panels with Rear Cable management system and mounting hardware to mount the patch panel. Should have port identification numbers printed/engraved on front of the panel. Etc. as required. All as per pre approved by Engineer in charge. |
| 13 | Modular Patch Panel Loaded with Cat -6 I/O |
| 14 | Supply , Installation and Testing of 4 pair, 100 Ohm impedance, Cat 6/6A /Class E/Ea patch cords should be constructed of minimum 23/24 AWG, stranded bare Copper cable with LSZH Jacket, with an enhanced performance by factory moulded RJ45 connectors with strain relief boots as per ANSI/TIA/EIA 568-C.2 suitable for Cat 6/6A application complying to latest ammendments Category 6/6A Standards, According. to TIA568C.2, ISO/IEC 11801, EN 50173, IEC 60603-7-51, EN 60603-7, IEEE 802.3an minimum requirement for 1G BASE-T to 10G BASE-T performance. Patch cords shall be straight thru cable compatible with both T568-A and T568-B wiring schemes, should support IEEE 802.3af / IEEE 802.3at for POE applications, Minimum 750 to 1000 mating cycles in plug contacts for long durability, Should support Ethernet 10GBASE-T, 1.2 Gb/s ATM, Token ring 4/16, Digital video and broadband/baseband analog video, Voice over internet protocal (VOIP). |
| 15 | Cat 6, U/UTP (Unscreened/Un-sheilded Twisted Pair) Patch Cord |
| 16 | 1 Mtr |
| 17 | 2 Mtr |
| 18 | Supply & Installation of IP-20 & IK-08 , Wall mounted Double Section Communication enclosure (Rack) made from powder coated (60 to 80 Micron) CRCA sheet, front sturdy sheet steel frame folded from one piece and welded with minimum 5mm toughened glass door,Vertical Mounting Rail 1.6 MM with 'U'Marking , with All round protective channel on the door aperture, lock integrated on front door, top and bottom cover with cable entry provision with gland plates, integrated side walls, 2 pair of 19\\" angles with wall mounting provision on wall. Accessories like: 1 No of 19\\" 1U Horizontal Cable manager, 1 No of 90 cfm 230V AC Fan with 1 mts long cable, mounting hardware , 1 No of 19\\" 1U, mountable socket strips with 5 nos of 5A universal sockets with 2 mts long power chord for supplying power to switches, fans etc along with earth continuity kit, indicator, moulded power supply cable. fixing on wall with Suitable Anchor fastner etc as required. |
| 19 | 15 U Rack with Width 600 mm & Depth 400 mm + 100 mm |
| 20 | SITC of following diagonal size professional Display, 4k Resolution, Brightness(Typ.) 440 nit and above , Contrast Ratio-2000:1 and above, Viewing Angle(H/V)-178/178, Response Time(G-to-G) 8ms, Input: RGB- Analog D-SUB, Video- HDMI 2.0 (2), HDCP- HDCP 2.2, Audio- Stereo mini Jack, USB- Only F/W upgrade, Outputs: RGB- DP1.2(Loop- out), Audio- Stereo mini Jack, External Control- RS232C(in/out), RJ45, External Sensor Detachable type(IR Ambient). Operation Hour 24/7. mounting bracket etc. as required. |
| 21 | SITC of 30 Watt speaker with taping facility having frequency range of 65Hz-20KHz@(-10db) with power handing of 200Watt continuous and more than 350 Watt @peak etc complete as required. |
| 22 | Supply & Installation of 240 Watt Mixer Amplifier Unit- for providing a crisp call or clear music with 4 microphone / line inputs, plus music source input, announcement only output, 3 wire volume override, with Mains power supply 230 VAC ±10%, 50 Hz (reduced power at lower mains), Inrush current 20 A , Power consumption 120W, Frequency response (Line) 80 Hz to 18 kHz (+1/‑3 dB @‑10 dB ref. rated output) Frequency response (Mic.) 80 Hz to 18 kHz (+1/‑3 dB @‑10 dB ref. rated output) Distortion <1%@ rated output power, 1 kHz Bass Control Max. ± 8 dB Treble Control Max. ± 8 dB, including making connection etc complete as required. |
| 23 | Supply & Laying of 2 Core size 0.5 sqmm copper shielded Cable for connectings Microphones with related conduits / fittings / termination, etc complete as required. |
| 24 | SITC of following capacity BIS certified 1Phase Input, 1Phase Output advance DSP controlled IGBT based rectifier Online UPS with Inbuilt Isolation Transformer having 0.99 Input power factor & 0.8 Output factor, Input voltage & frequency range of 180-300V on full load/ 110-300V on 50% load & 50 Hz +/- 5% and output voltage & frequency of 230V+/-1% & 50 +/- 0.1 Hz. Overall efficiency of upto 92% (without Transformer Loss), Overloading of 105 - 110% 30 mins, 111 - 130% 5 mins,131 - 150% 10 sec, THDv of < 3% for Linear & < 5% for Non linear load.UPS should have LED Panel with LCD display showing load level, Battery Voltage Level, Input & Output Voltage, Input & Output Frequency. UPS should have protection from Input High / Low;Over Load;Short Circuit; Over Temperature and give audible alarms on Battery Mode;Low Battery;Fault;Over Load & Bypass Mode. SMF Batteries of 12V VRLA for 30 mins with MS Rack and necessary cable for UPS to Batteries Installation. UPS should have valid Certification like Type III environmental declarations from third party renowned agency complying to ISO 14025, CE, ROHS,BIS,EN 62040-1, EN 62040-2, IEC 62040-3 Etc. as required. |
| 25 | 5KVA UPS with 4992 VAH Battery |
| 26 | S & F of 12V VRLA Lead Acid Sealed maintenance free (SMF) batteries of following capacity with Warranty of 2 years |
| 27 | 26 AH |
| 28 | Supply and laying speaker cable of following size 2 core twin twisted multi stranded electrolytic grade copper conductor, overall PVC insulated and armoured cable (Blue colour) on surface/ above false ceiling including cost of GI spacers, saddles etc. as required. |
| 29 | 1.5 Sq.mm |
| 30 | Providing & Fixing of Wiring Accessories OEM fabricated following size virgin material UPVC modular boxes on surface suitable for modular accessories as required. |
| 31 | 1-2 Module |
| 32 | Supplying, installation, Testing and commissioning of following capacity 24 port Non POE Layer 2 indoor Network Switch having features and specifications etc. as mentioned here under: At least 24 X RJ-45 Gigabit Ethernet Ports and additional 2 X 10G Base -T with 4 X SFP Ports with non-blocking architecture by having Switching capacity of min. 168Gbps and packet forwarding rate of 125Mpps or higher, 16K MAC table. Console Port, USB port, Stacking support of min. 8 units per stack. Internal dual AC Power supply, STP, RSTP, MSTP, BPDU Filter, BPDU Restriction, Min. 9K Jumbo Frame, LBD, IGMP Snooping V1/V2/V3, MLD Snooping V1/V2. IGMP /MLD Groups 1K or more, IPv4/IPv6 Loopback Interface, 16 L3 IP Interface, Ipv6 ND, VRRPv3, UDP Helper, ECMP. VLAN: 802.0Ǫ,Port based, Ǫ-in-Ǫ, Multicast VLAN, Protocol VLAN, VLAN Trunking, DHCP Snooping, Server, server Screening. RADIUS , TACACS+ Authentication, ǪoS: 802.0P, 8 queues per port, ǪoS : WRR, Strict+WRR, WRED, 802.0p. ACL: MAC based, IPv4C IPv6, TCP/UDP Port number, time based ACL, TFTP Client, SNMP V1, v2c, v3, SNMP traps, RMON, DHCP server, relay, client, LLDP, LLDP-MED, OAM, Dying Gasp, 802.0ah, sflow, RIP, OSPF v2/v3, policy based route, SSL, SSH. 6 kV surge protection on all Gigabit Ethernet ports and on all GE RJ-45 access ports. Certifications: UL, CE, FCC, RoHS, MTCTE, OEM/Product must be on Trusted Telecom Portal of Department of Telecommunication, Government of India etc. complete as required. |
| 33 | Supply, Installation, Testing & Commissioning of Digital Chairman Unit with Priority Button and Discussion Device that shall enable participants to take part in a discussion by speaking into a microphone and listening to proceedings on a loudspeaker. The device shall have Plug-and-play functionality, Compact, attractive, ergonomic design, with LED indicator in the Discussion Device and in head of microphone with flexible stem with Loudspeaker integrated into front of device having facility of headphone as well with Automatic level reduction when microphone is activated (configurable via web browser application of Control Unit): prevents acoustic feedback from headphone to microphone. GSM immunity with having Frequency response 200Hz-12.5kHz, Loudspeaker nominal output 72dB SPL. etc complete in repsect. |
| 34 | Supply, Installation, Testing & Commissioning of Digital Delegate Unit with Speak Button and Discussion Device that shall enable participants to take part in a discussion by speaking into a microphone and listening to proceedings on a loudspeaker. The device shall have Plug-and-play functionality, Compact, attractive, ergonomic design, with LED indicator in the Discussion Device and in head of microphone with flexible stem with Loudspeaker integrated into front of device having facility of headphone as well with Automatic level reduction when microphone is activated (configurable via web browser application of Control Unit): prevents acoustic feedback from headphone to microphone. GSM immunity with having Frequency response 200Hz-12.5kHz, Loudspeaker nominal output 72dB SPL. etc complete in repsect. |
| 35 | Supply, Installation, Testing & Commissioning of Control Unit with inbuilt recorder with Intuitive touch- buttons on the front panel for easy configuration and operation purposes. Intuitive LED indicators for clear and immediate feedback on the system settings.Web browser control – it shall be possible to use a web browser application to view and manage system settings.System control for up to 80 Discussion Devices.Hot swap of Discussion Devices, without having to power down the system. Plus/minus buttons and green LED indicators for setting the volume range of all connected Discussion Devices. Microphone-mode selection button and green LED indicators for selecting one of the following microphone operating modes: ‘open mode’, ‘override mode’, ‘voice activation mode’, and ‘push to talk (PTT) mode’. Number of Open Microphones (NOM) button and green LED indicators for selecting the number of microphones that can be activated at the same time. It shall be possible to select up to four open microphones at the Control Unit. Built-in Digital Acoustic Feedback Suppression (DAFS). USB connector on front of unit for connecting a USB memory stick. Gain reduction due to number of open microphones (NOM) 1/SQRT (NOM) Sample rate 44.1kHz Nominal input (85 db SPL) <0.5% Max. input (110 db SPL) <0.5%. etc complete in respect. |
| 36 | Supply, Installation, Testing & Commissioning of Extension cables and connectors for contribution units. etc complete in respect. |
| 37 | SITC of Cable Connectors. Of various types and sizes suitable for system etc complete in respect. |
| 38 | SITC of Cable locking clamps are used with extension cables to prevent accidental disconnectionas. etc complete in respect. |
| 39 | Supply, Installation, Testing & Commissioning of Handheld Wireless Mic with Cardiod polar pattern for transmitter,Dynamic microphone with Neodymium magnet , Receiver frequency response 80Hz- 18kHz,Receiver RF sensitivity < 1.0 µV,Receiver Image rejection>55dB,Receiver Dyanmic range >95dB and receiver having 32 channels possible,Receiver S/N ratio >100dB A,distortion <1 %, Transmitter sensitivity - 3.2 mV/Pa,modulation:+/-40kHz etc complete in respect. |
| 40 | Supply, Installation, Testing & Commissioning of 4X2 HDMI presentation switcher with matrix outputs. HDMI 2.0b, 4K@60Hz 4:4:4 8 bit, HDR 10, HDCP 2.2, 4K to 1080p down scaling. SPDIF and 3.5mm output for dual HDMI OUT audio extraction and dual HDMI OUT ARC, RS232, IR and TCP/IP control smart EDID managment complete in respect. |
| 41 | Supply, Installation, Testing & Commissioning of High−performance 19.5 meter HDMI male to HDMI male cable that supports signals up to 4K@60Hz (4:4:4), Deep color Should have Gold Plated pins Should have lockable connectors Should be of same make of Switcher,Scaler,Wall plate for the interoperability complete in respect. |
| 42 | Supply, Installation, Testing & Commissioning of High−performance 2 meter HDMI male to HDMI male cable that supports signals up to 4K@60Hz (4:4:4), Deep color Should have Gold Plated pins Should have lockable connectors Should be of same make of Switcher,Scaler,Wall plate for the interoperability complete in respect. |
| 43 | SITC of Digital Mixer : 4 balanced mic inputs, 2 balanced Mic/Line inputs and 1 stereo unbalanced input; 1 stereo and 2 mono outputs; 2-channel USB audio interface for soft codec (Skype, WebEx) integration or playback from computer; Full digital processing on inputs and outputs; 8 x 3 audio routing matrix; 6-channel Smart Mix (gate or gain sharing); Onboard acoustic echo canceler (AEC) processing; Front panel direct operation and Web Remote functionality; IP control for third-party CCS administration; Up to 6 mixers can be linked using Cat5e cable complete in respect. |
| 44 | Supply, Installation, Testing & Commissioning of 86\\" display along with Brightness : 500 nit (Typ.) Resolution : ULTRA HD (3,840 x 2,160) Pixel Pitch : 1.588 mm Built-in Speaker (30 W + 30 W) Interface : HDMI(3X2.0)/ DP/ DVI-D/ USB 2.0/ RS232C/ RJ45/ Audio/ IR, Contrast Ratio 5,000 : 1, nternal Memory4 GB, Wi-Fi Built-in Wi-Fi Input HDMI (3 (HDMI1/2 : HDCP 2.2/1.4, HDMI3)), DP (HDCP 2.2/1.3), DVI-D (HDCP 1.4), Audio In, RS-232C (4 Pin Phone-jack), RJ45 (LAN), IR In, USB 2.0 Type A, Output HDMI Out, Audio Out, RS-232C Out (4 Pin Phone-jack), Daisy Chain (Input HDMI, DP, DVI / Output HDMI) Complete in all respect. |
| 45 | Supply, Installation, Testing & Commissioning of Cable cubby having input of 15 pin HD,3.5mm audi,HDMI & ethernet,Pop-up pneumatic Lid cover etc complete etc. |
| 46 | \\"SITC of Digital Podium; Integrated Central Teaching Platform, (a) Main Cabinet System - Metallic structure customized to house hardware/software with powder coated fitted with cooling fans & caster wheels with brakes & provision to mount Smart Orator with beam splitting mirror, Podium with Std Dimension, External connectivity options: 2 x USB, 2 x XLR on Top and at right bottom – HDMI in/ Out, VGA In/ Out, Audio In/ Out, Gigabit LAN, Power socket with On/Off switch, Drawer for document camera, Metallic top tray for placing documents, laptop etc. dimensions 630mm x 655mm, Drawer for keyboard and mouse, Security- All drawers, Sliding Trays, and Doors should be lockable, Provision to fix Logo at the front side with the flexibility to change the logo, Provision of 19\\"\\" Rack inside podium to fit in international standard equipment with minimum adjustable shelves, Access doors for servicing both from front and back sides of the podium, Wire managers on for flexibility of managing additional wires/wiring. (b) Integrated multimedia controller on top panel with keypad to control Projector Screen, audio system volume control, switch on/off the PC & Projector, IR device control, RS232, LAN connector, USB etc. Switching among PC, Laptop and Document Camera with auto splitting between podium monitor & projection system, switching DVD & TV etc. Minimum three full HD (HDMI) input devices and minimum support for two full HD (HDMI) output for simultaneous display. (c) Interactive Display - Display size 21.5” Interactive Monitor with up to 60-degree adjustable motorized tilt, Resolution 1920 x 1080 pixel. 250 Cdm2, 10 Touch Point, HDMI/ DVI/VGA & USB Ports. (d)Hand Held Wireless Mic , Phantom Power for Gooseneck - Inbuilt selectable\\". |
| 47 | SITC of Workstation latest Intel® i7 processor, Intel Chipset motherboard, 08 GB RAM, 1 TB SATA HDD at 7200 rpm, with 2 x 4GB GPU type higher end Graphic card for H.265 compression technique with dual display ports/DVI/ HDMI port, Giga LAN Card, wireless Keyboard, wireless optical Mouse. |
| 48 | ADD GST@18% Please Enable Macros to View BoQ information |
