|
| 1 | providing and fixing double scaffolding system(cup lock type ) on theexterior side of building/struture, up to 25 meter hieght , above ground level , comp providing and fixing double scaffolding system(cup lock type ) on theexterior side of building/struture, up to 25 meter hieght , above ground level ,including additional rows of scoffolding in stepped ,manner as per etc all |
| 2 | Scrapping old white or colour wash including disposal of refuse as directed by Engineer-In-charge within a distance of 60 meters (200 feet) Scrapping old white or colour wash including disposal of refuse as directed by Engineer-In-charge within a distance of 60 meters (200 feet)- |
| 3 | 12mm cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement. 12mm cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement. |
| 4 | Finishing walls with Putty approved brand and manufacture and of required shade on undacorated wall surface Finishing walls with Putty approved brand and manufacture and of required shade on undacorated wall surface to give even shade over including curing and cost of all material, labour, T&P etc. required for proper completion of work |
| 5 | Finishing walls with exterior emulsion paint (Apex) Finishing walls with exterior emulsion paint (Apex) of approved brand and manufacture and of required shade on undacorated wall surface to give even shade over @ 1.25 Ltr/l0sqm including one coat of primer applld @ 0.75Ltr/10sqm coat curing and cost of all material, labour, T&P etc. required fororooer comoletlon of work.for two coat. |
| 6 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 2n and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25xl0x0.SO mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws@ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I): 2011 (Board with BIS Certification marks) |
| 7 | Dismantling brick work or stone work in lime or cement mortar and Including stacking of materials as directed by Engineer-In-Charge within a distance of 60 meters 1200 feet\. Dismantling brick work or stone work in lime or cement mortar and Including stacking of materials as directed by Engineer-In-Charge within a distance of 60 meters 1200 feet\. |
| 8 | Brick work with common burnt clay (non modular) bricks of class -150 in super structure Cement mortar 1:4 (1 cement: 4 coarse sand) Brick work with common burnt clay (non modular) bricks of class -150 in super structure above plinth level up to floor V level in all shapes and sizes. Cement mortar 1:4 (1 cement: 4 coarse sand) |
| 9 | Supply and fixing of anodized aluminium partition having 2mm thick aluminium. Section, partly glazed and partly 12mm thick laminated board. Aluminium board size 83.50x44.65mm as vertical member and 11.40x44.45 as bottom and horizontal member with all fitting, glass panes of 4mm thick handle and locks complete |
| 10 | Tile work in skirting risers of steps and dado up to 2m height over 12mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) 8mm thick Tile work in skirting risers of steps and dado up to 2m height over 12mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) 8mm thick etc all comp |
| 11 | Providing and laying Vitrified tiles In different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % Size of TIie 600x600 mm Providing and laying Vitrified tiles In different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, In all colours & shade, In skirting. riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), Jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the init with white cement & matching pigments etc. complete.- |
| 12 | Providing and flxlng aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on thebody, door weight upto 36 kg to 80 kg and door width from 701mm to 1000 No mm), with double speed adjustment with necessary accessories and screwsetc. complete. Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for f1Xing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein shall be made. dimension I.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this accountCasement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.) (Single Shutter Openable Window)- |
| 13 | Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of Joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured.\\" \\"Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:(a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm.(b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of Joints of fibre cloth should not be less than 10 cm.(c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around.(d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately.For the purpose of measurement the entire treated surface will be measured.\\" |
| 14 | Providing and fixing in position wall panels of plain teak wood particle board 12mm thick bonded with B.W.P. type Phenol formaldehyde synthetic resin tiles kall wood frame and provision for providing switch board fixtures etc. as per drawing complete with polishing and fining with Fremg wax polish as per direction given by Engineer-In-Charge. Wall Paneling: Providing and fixing in position wall panels of plain teak wood particle board 12mm thick bonded with B.W.P. type Phenol formaldehyde synthetic resin tiles kall wood frame and provision for providing switch board fixtures etc. as per drawing complete with polishing and fining with Fremg wax polish as per direction given by Engineer-In-Charge.- |
| 15 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part 1) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part 1) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary- |
| 16 | Painting on iron work with one coat of priming coat and two coat with superior synthetic enamel including supply of all material etc all comp. Painting on iron work with one coat of priming coat and two coat with superior synthetic enamel including supply of all material etc all comp.-Rate-103.00 per 1 Sqm. |
| 17 | 15 mm nominal outer dia Pipes Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, Including all CPVC plain & brass threaded fittings, 1/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same Including testing of Joints complete as per direction of Engineer In Charge. Concealed work, Including cutting chases and making good the walls etc.- |
| 18 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of Joints complete as per direction of Engineer In Charge.n External work |
| 19 | Wiring point for light with 1.5sq mm FR PVC insulated single core copper conductor cable in pvcconduct pipe on surface, complete with 14 SWG copper earth continuity wire, piano type switch and ceiling rose/angle/batten holder on 3mm thick phenolic laminated backelite-sheet etc. But in PVC cunduct with 1.5 sq.mm. FR PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduct. Wiring points in surface Cinduct with PVC insulated 1100 V grade cable. complete in all respects, a directed. Wiring point for light with 1.5sq mm FR PVC insulated single core copper conductor cable in pvcconduct pipe on surface, complete with 14 SWG copper earth continuity wire, piano type switch and ceiling rose/angle/batten holder on 3mm thick phenolic laminated backelite-sheet etc. But in PVC cunduct with 1.5 sq.mm. FR PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduct. Wiring points in surface Cinduct with PVC insulated 1100 V grade cable. complete in all respects, a directed.- |
| 20 | Wiring point for fan/fresh air fan (light duty exhaust fan) with 1 sq. mm. FR PVC insulated multistrand single core copper conducter cable in PVC conduit pipe on surface, complete with 14 SWG copper earth continuity wire, piano type switch & ceiling rose on 3 mm. thick phenolic laminated backelite sheet etc. But in PVC conduit with 1.5 sq. mm. FR PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit. Wiring points in surface conduit with PVC Insulated 1100 V garde cable. complete in all respects. Wiring point for fan/fresh air fan (light duty exhaust fan) with 1 sq. mm. FR PVC insulated multistrand single core copper conducter cable in PVC conduit pipe on surface, complete with 14 SWG copper earth continuity wire, piano type switch & ceiling rose on 3 mm. thick phenolic laminated backelite sheet etc. But in PVC conduit with 1.5 sq. mm. FR PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit. Wiring points in surface conduit with PVC Insulated 1100 V garde cable. complete in all respect |
| 21 | S/F of Exhaust fan with 1.5sq mm FR PVC insulated copper conductor cable in 25mm dia heavy duty etc all compete. S/F of Exhaust fan with 1.5sq mm FR PVC insulated copper conductor cable in 25mm dia heavy duty etc all compete |
| 22 | Supply and fitting of ceiling fan Usha, Khetan, Bajaj I.S.I mark including all complete. Supply and fitting of ceiling fan Usha, Khetan, Bajaj I.S.I mark including all complete. |
| 23 | Renewing glass panes and refixing existing wooden fillets: Float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm)- |
| 24 | SUPPLY WORK-p/f CP brass bib cock 15 mm size etc all comp p/f CP brass bib cock 15 mm size etc all comp- |
| 25 | Providing and fixing of white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. Brasss spreaders with brass unions and G.I. clamps complete. one urinal basin with 5litre wihte P.V.C. automatic flushing cistern. Providing and fixing of white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. Brasss spreaders with brass unions and G.I. clamps complete. one urinal basin with 5litre wihte P.V.C. automatic flushing cistern.- |
| 26 | Providing and fixing vitreous china dual purpose closet suitable for use as Squatting pan or European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of Standard make and mosquito proof coupling of approved municipal design Providing and fixing vitreous china dual purpose closet suitable for use as Squatting pan or European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of Standard make and mosquito proof coupling of approved municipal design |
| 27 | Mirror of Atul make with Indian polish of 600x450 mm dia size with beveled edge null |
| 28 | Mild Steel Iron Grill & Staircase railing of a approved qualitiy and drawing Including supply of all materials, fabrication, labour, T&P In all respect asper direction of Engineer-In-charge for proper completion of work at site.- |
| 29 | Providing and fixing wash basin with C.I. Brakckets, 15mm C.P. Brass pillar taps, 32mm C.P. Brass waste pipe of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White vitreous china wash basin size 630x450mm with a pair of 15mm C.P. brass pillar taps. Providing and fixing wash basin with C.I. Brakckets, 15mm C.P. Brass pillar taps, 32mm C.P. Brass waste pipe of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White vitreous china wash basin size 630x450mm with a pair of 15mm C.P. brass pillar taps |
| 30 | Supply and fixing of switch box 250 x 250 x 65 mm size of approved make made up of 1.0 mm thick ISI Marked G.P.sheet Supply and fixing of switch box 250 x 250 x 65 mm size of approved make made up of 1.0 mm thick ISI Marked G.P.sheet |
| 31 | Supply and fixing of LED Tube Light with batten suitable for up to 1 X 22 watt LED tube light fitting including tube on Surface complete in all respect. Supply and fixing of LED Tube Light with batten suitable for up to 1 X 22 watt LED tube light fitting including tube on Surface complete in all |
| 32 | S/F of L.E.D. bulb lighting of approved quality etc all complete. S/F of L.E.D. bulb lighting of approved quality etc all complete.- |
| 33 | Supply and Fixing of recess mounting round 18 Watt COB LED Spot Light having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. AR Supply and Fixing of recess mounting round 18 Watt COB LED Spot Light having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. |
| 34 | Add 18 % G.S.T. Please Enable Macros to View BoQ information |
