|
| 1 | SCHEDULE-'A' Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. a) All kinds of soil. |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. a)All kinds of soil. |
| 3 | Excavating holes more than 0.10 cum & upto 0.5 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5 m. a) All kinds of soil. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: a) 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 5 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge .(a) 60 mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. |
| 6 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). |
| 7 | Making bajri path including preparation of subgrade, supplying and laying brick aggregate of 50 mm nominal size 7.5 cm deep with binding material consisting of 12 mm moorum and 12 mm red bajri consolidated with road roller. |
| 8 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:(a) Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. |
| 9 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : (a) 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural source:3 graded stone aggregate 20 mm nominal size) derived from natural source. |
| 10 | Providing and fixing \\"Air Walker\\" with the specifications below:1. Dimensions (LxWxH) 1100 x 450 x 1300 mm.2. Fabricated with main post of NB 100mm (G.I.) \\"C\\" Class Pipe of approved make.3. U-shaped main frame of NB 80mm (G.I.) \\"C\\" Class Pipe Leg support frame of NB 50mm (0.1) \\"C\\" Class Pipe4. Handy frame pipes of NB 32mm (G.I.) \\"C\\" Class (NB stands for Nominal Bore i.e internal Diameter of pipe in millimetres).5. All pipes are powder-coated with 80-120 micron thick AkzoNobel or equivalent paints.6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Baseplate cover made of virgin LLDPE plastic by rotational molding with a minimum of 4.00mm thickness, UV resistant and coloured.9. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury.10. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured.11. The equipment must be fitted with inbuilt limiters to prevent unwanted movements.12. The equipment is to be fixed on the ground by providing and laying Cement Concrete wilh a minimum size of block to be constructed of 0.60mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.13. High tensile steel with galvanized nut bolts is used for assembly.14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover.15. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.16. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years.17. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. |
| 11 | Providing and fixing a double \\"Sit-Up Station\\" with the specifications below:1. Dimensions (LxWxH): 1500 x 11500 x 650 mm.2. Fabricated with main frame of NB 100mm (G.I.) \\"C\\" Class Pipe of approved make.3. Main frame of NB 25mm (G I.) \\"C\\" Class Pipe.4. Leg support of NB 65mm (G.I.) \\"C\\" Class Pipe ('NB' stands for Nominal Bore i.e . Internal Diameter of pipe in millimetres).5. Fixed on its top is back support made of perforated MS sheet of 2mm thickness.6. All pipes are powder-coated with 80-120 micron thick AkzoNobel or equivalent paints.7. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.8. Zinc primer paint is applied at all the welding points prior to finishing9. Baseplate cover made of virgin LLDPE plastic by rotational molding with a minimum of 4.00mm thickness, UV resistant and coloured.10. The equipment is to be fixed on the ground by providing and laying Cement Concrete wilh a minimum size of block to be constructed of 0.60mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.11. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with a basteplate cover.12. High tensile steel with galvanized nut bolts is used for assembly.13. Equipment made to EN16630 & DIN 79000 lnternational standard for outdoor fitness equipment.14. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years.15.This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. |
| 12 | Providing and fixing \\"Air Swing\\" in a pair with the below specifications:1. Dimensions (LxWxH) 1150 x 900 x 1250 mm.2. Fabricated with main post of NB 100mm (G.I.) \\"C\\" Class Pipe of approved make.3. Leg Support frame of NB 50mm (G.I.) \\"C\\" Class Pipe4. Handle support frame of NB 32mm (G.I.) \\"C\\" Class Pipe. ('NB' stands for Nominal Bore i e.. Internal Diameter of pipe in millimeters).5. All pipes are powder-coated with 80-120 micron thick AkzoNobel or equivalent paints.6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Handle bars are provided with high-end quality rubber grips.9. Baseplate cover made of virgin LLDPE plastic by rotational molding with a minimum of 4.00mm thickness, UV resistant and coloured.10. Foothold made of MS Sheet Metal with rounded edges to prevent impact and injury.11. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured.12. The equipment must be fitted with inbuilt limiters to prevent unwanted movements.13. The equipment is to be fixed on the ground by providing and laying Cement Concrete wilh a minimum size of block to be constructed of 0.60mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.14. Once the concrete is set, the equipment is fixed on to it.15. High tensile steel with galvanized nut bolts is used for assembly.16. Equipment made to EN16630 & DIN 79000 lnternational standard for outdoor fitness equipment17. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years..18. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. |
| 13 | Providing and fixing \\"Horse Rider Station\\" with the specifications below:1. Dimensions (LxWxH): 1000 x 600 x 1100 mm.2. Fabricated with main post of NB 100mm (G.I.) \\"C\\" Class Pipe of approved make.3. Main frame of NB 65mm (G I.) \\"C\\" Class Pipe.4. Handle support frame of NB 50mm (G.I.) \\"C\\" Class Pipe and other pipes of 4 NB 32mm & NB 25mm (G.I.} \\"C\\" Class Pipe. ('NB' stands for Nominal Bore i.e . Internal Diameter of pipe in millimeters).5. All pipes are powder-coated with 80-120 micron thick AkzoNobel or equivalent paints.6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Baseplate cover made of virgin LLDPE plastic by rotational molding with a minimum of 4.00mm thickness, UV resistant and coloured.9. Foothold made of NB 32mm (G.I.) \\"C\\" Class Pipe.10. Seat to be made up from virgin LLDPE manufactured by rotational moulding with 4.00mm thickness, coloured, UV resistant and environmental friendly.11. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured.12. The equipment must be fitted with inbuilt limiters to prevent unwanted movements.13. The equipment is to be fixed on the ground by providing and laying Cement Concrete wilh a minimum size of block to be constructed of 0.60mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover.15. High tensile steel with galvanized nut bolts is used for assembly.16. Equipment made to EN16630 & DIN 79000 lnternational standard for outdoor fitness equipment17. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years..18. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. |
| 14 | Providing and fixing \\"Leg Press\\" in a pair with the below specifications:1. Dimensions (LxWxH) 2000 x 550 x 1600 mm2. Fabricated with main post of NB 100mm (G.I.) \\"C\\" Class Pipe of approved make.3. Seat Main frame of NB 50mm (G.I.) \\"C\\" Class Pipe and Pipe connecting main post to seat main frame of NB 65mm (G.I.) \\"C\\" Class Pipe. ('NB' stands for Nominal Bore i.e.. Internal Diameter of pipe in millimetres).4. All pipes are powder-coated with 80-120 micron thick AkzoNobel or equivalent paints.5. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.6. Zinc primer paint is applied at all the welding points prior to finishing.7. Baseplate cover made of virgin LLDPE plastic by rotational molding with a minimum of 4.00mm thickness, UV resistant and coloured.8. Foothold is made of NB 50mm (G.I.) \\"C\\" Class Pipe.9. Seat to be made up from virgin LLDPE manufactured by rotational moulding with 4.00mm thickness, coloured, UV resistant and environmental friendly.10. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured.11. The equipment must be fitted with inbuilt limiters to prevent unwanted movements.12. The equipment is to be fixed on the ground by providing and laying Cement Concrete wilh a minimum size of block to be constructed of 0.60mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover.14. High tensile steel with galvanized nut bolts is used for assembly.15. Equipment made to EN16630 & DIN 79000 lnternational standard for outdoor fitness equipment16. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years..17. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. |
| 15 | Providing and fixing \\"Pull Chair\\" in a pair with the below specifications:1. Dimensions (LxWxH). 2400 x 800 x 2000 mm2. Fabricated with main post of NB 100mm (G.I.) \\"C\\" Class Pipe of approved make.3. Seat Main frame of NB 50mm (G.I.) \\"C\\" Class Pipe, Pipe connecting main post with handle frame of NB 65mm (G.I.) \\"C\\" Class Pipe.4. Handle frame of NB 32mm (G.I.) \\"C\\" Class Pipe. (\\"NB\\" slands for Normnal Bore i e .. Internal Diameter of pipe in millimetres).5. All pipes are powder-coated with 80-120 micron thick AkzoNobel or equivalent paints.6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Handle bars are provided with high-end quality rubber grips.9. Baseplate cover made of virgin LLDPE plastic by rotational molding with a minimum of 4.00mm thickness, UV resistant and coloured.10. Seat to be made up from virgin LLDPE manufactured by rotational moulding with 4.00mm thickness, coloured, UV resistant and environmental friendly.11. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured.12. The equipment must be fitted with inbuilt limiters to prevent unwanted movements.13. The equipment is to be fixed on the ground by providing and laying Cement Concrete wilh a minimum size of block to be constructed of 0.60mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover.15. High tensile steel with galvanized nut bolts is used for assembly.16. Equipment made to EN16630 & DIN 79000 lnternational standard for outdoor fitness equipment17. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years.18. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. |
| 16 | Providing and Fixing \\"SEATED CHEST PRESS\\" in a pair with the below specifications:-1. Dimensions (LxWxH): 1800 x 700 x 2000 mm2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Seat Main frame of NB 50mm (G.I.) ‘C’ Class Pipe.4. Handle frame of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Handle bars are provided with high end quality rubber grips.9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly.11. Maintenance-free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.12. The equipment are fitted with inbuilt limiters to prevent unwanted movements.13. The equipment is to be fixed on the ground by providing and laying Cement Concrete with a minimum size of block to be constructed of 0.60mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.15. High tensile steel with galvanized nut bolts are used for assembly.16. Equipment made to EN16630 & DIN 79000 lnternational standard for outdoor fitness equipment17. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years.18.This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. |
| 17 | Providing and Fixing \\"ARM WHEEL\\" in a pair with the below specifications:-1. Dimensions (LxWxH): 850 x 800 x 1800 mm2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Wheel frame of NB 32mm with connecting spokes of NB 25mm, Pipe connecting main pillar with wheel frame of NB 50mm. All pipes must be (G.I.) ‘C’ Class Pipes. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).4. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.5. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.6. Zinc primer paint is applied at all the welding points prior to finishing.7. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.8. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.9. The equipment is to be fixed on the ground by providing and laying Cement Concrete with a minimum size of block to be constructed of 0.60mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.10. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover.11. High tensile steel with galvanized nut bolts is used for assembly.12. Equipment made to EN16630 & DIN 79000 lnternational standard for outdoor fitness equipment.13. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years.14. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. |
| 18 | Providing and Fixing an \\"ELLIPTICAL EXERCISER\\" with the below specifications:1. Dimensions (LxWxH): 1200 x 550 x 1600 mm2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Main frame of NB 80mm (G.I.) ‘C’ Class Pipe.4. Handle frame of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Handle bars are provided with high end quality rubber grips.9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.11. The equipment is to be fixed on the ground by providing and laying Cement Concrete wilh a minimum size of block to be constructed of 0.60mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.12. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.13. High tensile steel with galvanized nut bolts are used for assembly.14. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.15. Self-Explanatory stainless steel label fixed on equipment for ease of use.16. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury, including maintenance cost for 2 years.17.This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. |
| 19 | Providing and Fixing \\"DOUBLE CROSS WALKER\\" with the specifications below:1. Dimensions (LxWxH): 1600 x 600 x 1600 mm2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Handle main frame of NB 50mm and other connecting pipes of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).4. Foot support frame of 96 x 46 x 3mm MS rectangular pipe.5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness, UV resistant and colored.9. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury.10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.11. The equipment are fitted with inbuilt limiters to prevent unwanted movements.12. The equipment is to be fixed on the ground by providing and laying Cement Concrete wilh a minimum size of block to be constructed of 0.60mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.14. High tensile steel with galvanized nut bolts are used for assembly.15. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.16. Self-Explanatory stainless steel label fixed on equipment for ease of use including maintenance cost for 2 years.17. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. |
| 20 | Providing and Fixing \\"Triple Twister\\" with the specifications below:1. Dimensions (LxWxH): 1300 x 1300 x 1650 mm2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Handle Main frame of NB 32mm (G.I.) ‘C’ Class Pipe.4. Handle frame spokes of NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).5. Foothold plate made of MS Sheet Metal of 3mm thickness.6. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.7. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.8. Zinc primer paint is applied at all the welding points prior to finishing.9. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.10. The equipment is to be fixed on the ground by providing and laying Cement Concrete wilh a minimum size of block to be constructed of 0.60mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.11. Once the concrete is set, the equipment is fixed on to it.12. High tensile steel with galvanized nut bolts are used for assembly.13. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.14. Self-Explanatory stainless steel label fixed on equipment for ease of use including maintenance cost for 2 years.15. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. |
| 21 | Providing and Fixing \\"ROWING MACHINE\\" with the specifications below:1. Dimensions (LxWxH): 1250 x 800 x 1150 mm2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Main frame of NB 65mm (G.I.) ‘C’ Class Pipe.4. Handle support frame of NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.9. Foothold made of NB 50mm (G.I.) ‘C’ Class Pipe.10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly.11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.12. The equipment are fitted with inbuilt limiters to prevent unwanted movements.13. The equipment is to be fixed on the ground by providing and laying Cement Concrete wilh a minimum size of block to be constructed of 0.60mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.15. High tensile steel with galvanized nut bolts are used for assembly.16. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.17. Self-Explanatory stainless steel label fixed on equipment for ease of use including maintenance cost for 2 years.18. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. |
| 22 | Providing and fixing \\"STAIR STEPPER WITH TWISTER\\" with the specifications below:1. Dimensions (LxWxH): 1000 x 800 x 1400 mm2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters)3. Twister main frame of NB 32mm (G.I.) \\"C\\" Class Pipe and Handle frame of NB 32mm (G.I.) ‘C’ Class Pipe. Twister Foothold plate made of MS Sheet Metal of 3mm thickness.4. Stepper main frame of MS pipe 96 x 46mm and Handle frame of NB 32mm & 25mm (G.I.) ‘C’ Class Pipe.5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury.9. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.10. The equipment is to be fixed on the ground by providing and laying Cement Concrete wilh a minimum size of block to be constructed of 0.60mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.11. Once the concrete is set, the equipment is fixed on to it.12. High tensile steel with galvanized nut bolts are used for assembly.13. Equipment made to EN16630 & DIN 79000 lnternational standard for outdoor fitness equipment.14. Self-Explanatory stainless steel label fixed on equipment for ease of use.15. The equipment are fitted with inbuilt limiters to prevent unwanted movements.16. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored including maintenance cost for 2 years.17. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. |
| 23 | Providing and fixing an\\"EXERCISING BAR\\" with the specifications below:1. Dimensions (LxWxH): 1800 x 550 x 1500 mm2. Fabricated with main frame of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Main frame of NB 32mm (G.I.) ‘C’ Class Pipe.4. Leg support of NB 65mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).5. Fixed on its top is back support made of perforated MS Sheet of 2mm thickness.6. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.7. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.8. Zinc primer paint is applied at all the welding points prior to finishing.9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.10. The equipment is to be fixed on the ground by providing and laying Cement Concrete wilh a minimum size of block to be constructed of 0.60mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.11. Once the concrete is set, the equipment is fixed on to it.12. High tensile steel with galvanized nut bolts are used for assembly.13. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.14. Self-Explanatory stainless steel label fixed on equipment for ease of use including maintenane cost for 2 years.15. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. |
| 24 | SCHEDULE -'B' |
| 25 | Regular maintenance for three years (after free maintenace for 2 years) of all the Gym Equipment 14 Nos. installed at each location in DDA parks as per schedule A consists of the following:-a) Replacement/repair of repair of parts of equipment in case of theft/vandalism.b) Check and set right/replacement for worn bearings, misaligned moving points, adjust/tighten loose parts, covers, seats, foundation and flooring.c) Tightening nuts/bolts/screws welding of various parts/joints of equipment wherever required.d) Calibration of instrument every three months.e) Priming coat & painting coat , if required.f) Lubrication/oiling every 15 days.g) Inspect and adjustment of drive, timing and running belts.h) Replacement of damaged parts & rectification of any other defects observed as per the direction of the Engineer-in-charge except:i. Due to force majeure or ii. Abnormally bad weather,serious loss or damage by fire oriii. Damage due to the act of god oriv. Any other cause which is in the absolute discretion of the Engineer-in-charge is beyond the contractor's control. |
| 26 | Annual comprehensive maintenance of equipments to be carried out by the agency after the date of completion of the work as per Schedule-A shall be as follows:- |
| 27 | Ist Year AMC (Free) (All 2 set open Gym equipment) |
| 28 | IInd Year AMC (Free) (All 2 set open Gym equipment) |
| 29 | IIIrd Year AMC (3% of equipment cost) (All 2 set open Gym equipment) |
| 30 | IVth Year AMC (3% of equipment cost) (All 2 set open Gym equipment) |
| 31 | Vth Year AMC (3% of equipment cost) (All 2 set open Gym equipment) |
| 32 | Total 2229014.00 |
| 33 | Total amount of DSR items (item no 1 to 9) = 858,051.00 |
| 34 | GST Correction factor @ 0.973 on DSR Items (i.e. item no. 1 to 9) = 834,883.62 |
| 35 | Add Cost Index @ 3% on DSR items |
| 36 | Total of DSR Items after GST C.F & C.I = 859,930.13 |
| 37 | Sum of amount of Non- DSR items (i.e, item no. 10 to 24.5) = 1,370,963.00 |
| 38 | TERMS & CONDITIONS 1 The agency shall regular inspect or upkeep the equipment in working condition as required.2 The complaint as and when occurred shall be attended within 3 days during 5 years maintenance period, failing which penalty @ Rs. 2000.00 per day shall be imposed and shall be recovered.3 If the equipment (or its parts) is stolen due to negligence in maintenance by the agency, the agency must replace the stolen equipment/parts. No payment will be made to the agency for this replacement (i.e., the agency bears the full cost).4 The performance guarantee of 5% submitted by the agency shall be released after recording of final completion certificate (i.e. after completion of 5-year maintenance period).5 The provisional completion shall be recorded by the competent authority separately for the period of replacement & refurbishment of equipments and maintenance of refurbished equipments. However, the final completion certificate shall be recorded by the competent authority after successful completion of 5-year maintenance period.6 The security deposit @ 2.5% of the gross amount of each running bill and final bill till the sum deducted will amount to security deposit of 2.5% of the tendered amount of the work shall be released after recording of final completion certificate (i.e. after completion of 5 year maintenance period).7 An amount equal to 40% cost of new equipments (i.e New equipments from S.No. 10 to 23 in schedule) shall be withheld apart from security deposit from each R/A bill against warranty. This amount shall be proportionately released year wise after successful completion of each year of maintenance period of 5 year (i.e. including free and paid maintenance period). Please Enable Macros to View BoQ information |
