|
| 1 | Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed. |
| 2 | M&L Brickwork with sub class ‘B’ bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 3 | M&L for Brickwork with burnt old size bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and as directed. |
| 4 | M&L providing plain cement concrete type B1 (1:2:4), (using 20mm graded stone aggregate), as in copings, bed etc all as specified and directed. |
| 5 | M&L plain cement concrete type B-2, (1:2:4),(using 20 mm graded stone aggregate), surface channels and drains complete all as specified and directed. |
| 6 | M&L rendering 15mm thick with cement mortar 1:4 on fair faces of brick work mixed with water proofing compunder as per manufacturers instruction or 2% by weight of cement and finishing the surfaces even and fair complete all as specified and directed. Note:- WPC shall be measured & paid separately |
| 7 | M&L for Precast reinforced cement concrete type 1:2:4 (using 20mm graded aggregate) cover slab as in drain cover, manhole cover, etc, set in cement mortar 1:4 complete all as specified and directed. |
| 8 | M&L TMT bar 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 9 | Demolition of unreinforced Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed. |
| 10 | M&L 75mm thick cement concrete type D-2 (1:4:8) using 40 mm graded stone aggregate as in sub base complete all as specified and directed. |
| 11 | M&L 50mm thick cement concrete type D-2 (1:4:8) using 40 mm graded stone aggregate as in sub base complete all as specified and directed. |
| 12 | S&F 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 13 | M&L Heavy duty Coloured Ceramic Tiles, 600 x 600 x 12-15mm thick as in steps, stairs, in flooring set and jointed in adhesive compound as per manufacturers instruction and pointed in White Cement mixed with Pigment to match the colour of tiles over and including 15 mm thick screed bed or bedding layer in CM 1:4 including dismantling of old heavy duty tiles, complete all as specified and directed. |
| 14 | Dismantling Plain or corrugated steel sheeting, any thickness roof coverings complete all as specified and as directed |
| 15 | S&F color coated (SDP) pre painted galvalume aluminium zinc coating AZ150 GI based corrugated steel sheet 0.5 mm thick (BMT) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self taping screw, butyl tape, end foam filler including dismantling plain or corrugated steel sheeting any gauge, thickness in roof covering as specified. |
| 16 | Dismantling wrought iron or mild steel work of any description not otherwise provided for. complete all as specified and directed. |
| 17 | S&F Rolled sections as in main and cross beams, hip and jack rafters;purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates. confirming to Fe-290.410W. Gde-E- 165 quality A) complete all as specified and as directed. |
| 18 | Dismantling posts or struts (Steel / wooden / RCC) any section embedded in natural ground, including taking out embedded portion and making good disturbed ground complete all as specified and directed. |
| 19 | Dismantling fencing wire mesh, any type complete all as specified and directed. |
| 20 | Excavation in post holes or similar hole each not exceeding 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layer not exceeding 25cm in soft/loose soil, complete all as specified and directed. |
| 21 | M&L plain cement concrete type B-2 (1:2:4) using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed. |
| 22 | M&L for MS work for fencing post and struts made from angle iron and flat iron in any section including cutting tops to shape, drilling holes and notching for fixing of wires including including bolting with MS screw bolt etc confirming to Fe-290 or Fe-330, complete all as specified and directed. |
| 23 | Supply only PVC coated chain link MS Zinc coating 60gsm as per IS 4826 fencing of any mesh size (as desired) and 4mm dia wire complete all as specified. |
| 24 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and as directed. |
| 25 | S&F in repair Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and as directed. |
| 26 | S&F MS round bar 10mm dia for holding chain link fencing, nibs etc. with fencing postscomplete all as specified and as directed. |
| 27 | M&L preparing new or previously untreated Steel and Iron Surfaces of any description, over 10 Sq Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a Red Oxide Zinc Chrome Primer, complete all as specified and as directed. |
| 28 | M&L preparation new iron and steel surfaces of any description, not exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chromr primer complete all as specified and directed. Please Enable Macros to View BoQ information |
