|
| 1 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing etc. as required of following size. OEM must have its own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work refer Annexure A attached with this BSR 16.0 Sq. mm 4 Core |
| 2 | : Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing etc. as required of following size. OEM must have its own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work refer Annexure A attached with this BSR 25.0 Sq. mm 3.5 Core |
| 3 | Add Extra for Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade direct in ground including excavation of trench of size 75 cm (Depth) x 35 cm(Width) , with procedure as per following points:- (a) Make a river sand bed of height 125 mm along the trench, (b) Lay the cable in the middle of the trench, (c) Provide river sand bed of height 125 mm on top of the cable, (d) Lay the protective Common burnt clay F.P.S. Bricks of Class designation 75 / Sand stone slabs of 50 mm thickness and 225 mm wide just above the sand bed vertically across the cable ( Approx. 9 no. Bricks per Mtr.), (e) Backfill the excavated soil leaving 300 mm from the Ground level, (f)Lay the Cable warning tape and again back-fill the remaining portion of the trench upto the ground level and compacting the earth |
| 4 | P / L of Double wall corrugated HDPE pipe confirming to IS : 16205 P-24,Stiffness Class 750 N, Externally corrugated and having smooth surface insidewith HDPE Coupler, Elbow, Tee at required Depth below the ground for layingcable of following Nominal Outer dia. MFR Test report from NABL accrediated is to be submitted.(Excavation of Earth & Back filling with compaction is to be Paid Extra)All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR 50mm Dia |
| 5 | Providing & Fixing of IK08 IP65 protected Top/Bottom mounted LED Post top Luminarie made of single piece construction powder coated die cast alluminium housing with UV stabalized Clear / frosted Polycarbonate diffuser and Aluminium anodised with sand blast reflector. The System level Luminous efficacy ≥ 100 Lumen/W. SMD LEDs is to be used, System CRI>70, CCT: 3000/4000/6500 K. The integral electronic driver must be potted & has a unique BIS R number must be potted & has a unique BIS R number constant current and Internal/external surge protection device of min. 4KV(L-N) and efficiency > 85%, PF>0.9, THD<10% and input Voltage range of 140-270V AC at 50Hz. System life of 50000 Burning hours with 70% of Initial Lumens maintained . Driver current <750mA. Fixture must be in compliance with BIS Standards and Trade mark Certificate complete in all respect.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR . Minimum lumen output 4500 lm Post top Luminarie |
| 6 | Providing and Laying RCC Foundation for Octagonal / Conical Street Light poles, High mast Poles as per Drawing attach at Table P-4 with Following Procedure & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure A attached with this BSR . A) Excavation of Pit for Foundation Size upto required depth from Ground level B) Dressing of Pit and Dry stone pitching 200 mm thick including supply of stones and preparing surface complete.C) Providing and laying in position cement concrete of M-10 grade of 75 mm thickness.D) Reinforcement for R.C.C. work with TMT bars including straightening, cutting, bending, placing in position and binding all complete.E) Centring and shuttering including strutting , propping etc. and removal of form work for Footing and Pedestal.F) Providing & Fixing of 2 no. Required Size PLB HDPE Pipe & Foundation Bolt with template as per OEM Recommendations.G) Providing and Laying Reinforce cement Concrete of M-25 grade in Footing and Pedestal including Curing the foundation for 7 days.H) Providing and Fixing Nosing Angle 40 mm x 40 mm x 6mm with 2 no. 100 mm long, 10 mm dia. Lugs on each face. Pole Foundation for Octagonal pole from 7 Mtr. To 9 Mtr. |
| 7 | Supply and installation of spike of M.S. rod 20mm dia 3.0mtr. long for earthing of (tower/pole) drive into earth by mechanical means sturcture connection the spike with cross arm top hamper PCC pole, lattics tower to earth etc. complete as per technical specification of DISCOM. |
| 8 | Supply & Laying following size B class, G.I. Pipe confirming to 15: 1239 P-1 (2004) with accessories like bend, socket etc. for laying earth conductor/strip/ cable in ground/ surface/ recess as required. All as per pre approved by Engineer in charge. (Earth Excavation will be Paid Extra)All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annex ure A attached with this bsr.40mm dia. |
| 9 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure A attached with this BSR 2 x 1.5 sq.mm |
| 10 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR Single pole MCB (With B/C curve tripping Characteristics) , 6 A to 32 A rating |
| 11 | SITC of Automatic Street Light Control system with CCMS to schedule the timing of lights (Reprogrammed based on astronomical clock or on field or through central control), ON/OFF switch (On field or centrally). connection type Three phase 18 Kw load, operating voltage 90-415V ac per phase L-N 50 Hz, Load Handling Capacity Minimum 8 kVA per phase, supports LED Light. 24 Hours Li-ion battery back-up for communication, 220mAh coin cell for RTC, with earthing of panel and devices and 5 years comprehensive maintenance including communication system. Protective features with auto cut and auto recovery using threshold configuration for short circuit, over voltage. CCMS system to capture the energy usage and other parameters at predetermined interval and store data for 30 days, download data in field via mobile app or mobile dash board, system protection against surges, upgrade firmware on field using a communication device via WIFI / GSM and GPRS low voltage High Voltage Trip, Overload cutoff and operating voltage. Surge Protection: CAT B (6 kV/3 kA). Lamp Protection: 160-280Vac per phase L N, 63A relay, 40A SP MCBs and 63 A 4P MCBs Monitoring: Voltage, current, power, power factor, energy, lamp hours Data Storage: 30 days history, 1-year report. Timers: Scheduled and astronomical Switching: Remote and onsite. Additional Features: GPS locator, event recording for supply and relay ON/OFF. MS sheet with two coats of enamel paint, duly hinged doors operable from both side with gasketing and locking arrangement mounted on angle iron frame of size 35 mm x 35 mm x 3 mm and proper lugging ferruling and gland plate and glands contractor phase indicator lamps and power and control wiring/cabling, proper earthing provision having Panel Size-3.2mm Sheet(L)-600mm*(H)-1000mm*(D)-350mm. |
| 12 | 150Watt Led Light (Warm White): Providing & Fixing of Suspended mounting IK08, IP 66 protected LED Light Luminaire on pole arm. Fixture design & Shape shall be as per provided drawing. Fixture made of powder coated single piece pressure die cast aluminium material with heat dissipation fins on housing with PC Clear Diffuser & LED should be SMD type of 3 to 5W each. The System efficacy ≥ 110 lm/wt output and potted driver & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with High voltage Cutoff @ 300 V AC and Auto resetting Safety, Power Factor > 0.95 driver Efficiency > 85%, THD < 10%, CRI >70, life time of minimum 50000 burning hours with 70% of initial lumen maintained, LED driving output current <750mA and CCT 3000K ±300K. Surge protection shall be min >= 4 KV internal and min 10 KV external inside driver compartment. The luminaire should have a separated driver compartment to ensure better thermal management. Driver should have Phase to phase protection of 440 V for 4 Hrs. Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be as per IS 10322 Compliance. OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre-approved by Engineer in charge. LED Light fixture with Minimum lumen output 16500 lm. |
| 13 | Item Code: [9 Mtr Mayur Decorative Single Arm Pole]-Supply,fabrication, transportation, loading, unloading, erection, fixing, testing and commissioning of 9.0 Meter Decorative Single Arm Peacock Pole, complete in all respect as per approved drawing, approved sample, technical specifications and as per directions of Engineer- in-Charge, comprising the following:• Main Shaft: MS Pipe (YST-240 grade),bottom section of 165 mm Dia × 3.25 mm thick and upper section of 139 mm Dia × 3.25 mm thick as per approved drawing, complete with all required internal supports. •Decorative Base: 1000 mm height & Cast Aluminum material which Include an in-built, removable cover on service window. • Base Plate: 380 mm dia × 12 mm thick MS plate, PCD 300 mm, 24 mm dia holes suitable for M20 foundation bolts & complete with rib supports of size 65 × 150 × 6 mm, with fixing accessories. The decorative Single arm: Peacock / Mor-Pankh top assembly, arm 1925 mm projection, 2.5mm thick MS(IS 2062 Grade E250/350), sheets complete with approved artistic profile and decorative shape as per drawing include CNC / laser cut patterns, including Mor-Pankh and artistic ornamental motifs on Shaft backed with UV-stabilized milky polycarbonate / acrylic diffuser pole with proper structural strength, stability & free from any deformation. The decorative CNC / laser cut portions of arms shall be internally illuminated with IP-67 (3000K Warm White) Flexible Neon silicon profile Flexible Silicon neon strip will be square in shape 14x14mm having minimum 6 Watt per meter, 12V DC operated, complete with all required fixing accessories and suitable capacity Heavy Duty IP-67 HPF drivers / SMPS housed inside the service window for outdoor use.• The approximate total Neon LED Strip length shall be 12Mtr per pole +/- 10%, complete for full illumination of decorative ornamental arms.• 05 Nos. 1 Watt LED Spot Lights, IP-65, aluminum body, warm white, shall be mounted at approved decorative locations as shown in drawing. •Provision for an internal termination box with a 4-way heavy-duty connector and 3 Nos. 6 Amp SP MCB (10kA). •The pole shall also include complete mounting arrangement, housing, support frame, cut- out and internal route for wiring at arm ends for installation of 150 Watt Flush Mounted Decorative LED Street Light; however, 150W LED street light fixtures / luminaires themselves shall not be included in this item. •The arm for 45Watt lantern shall be the part of pole & same as shown in provided drawing •The complete pole shall be finished with proper surface cleaning & surface preparation, anti-corrosive primer, UV-stabilized powder coating, and final approved Artistic High-Gloss Exterior PU Paint micron not less than 80 micron Finish in combination of Royal Blue and Golden shades, including multicolour artistic paint Highlighting on Peacock feathers and ornamental motifs, or as approved by Engineer-in-Charge. • Final shades, artistic pattern detailing, and finish quality of the pole shall be finalized based on an approved prototype sample prior to commencement of bulk production. The scope of the item shall include provision of all labour, T&P, consumables, welding, fitting, proper alignment, erection, testing, commissioning, and all incidental works necessary for complete and satisfactory installation of the pole system. |
| 14 | Supply, fabrication, transportation, loading, unloading, erection, fixing, testing and commissioning of 9.0 Meter Decorative Dual Arm Peacock Pole, complete in all respect as per approved drawing, approved sample, technical specifications and as per directions of Engineer- in-Charge, comprising the following:• Main Shaft: MS Pipe (YST-240 grade),bottom section of 165 mm Dia × 3.25 mm thick and upper section of 139 mm Dia × 3.25 mm thick as per approved drawing, complete with all required internal supports. •Decorative Base: 1000 mm height & Cast Aluminum material which Include an in-built, removable cover on service window. • Base Plate: 380 mm dia × 12 mm thick MS plate, PCD 300 mm, 24 mm dia holes suitable for M20 foundation bolts & complete with rib supports of size 65 × 150 × 6 mm, with fixing accessories. The decorative dual arm: Peacock / Mor-Pankh top assembly, arm 1925 mm projection, 2.5mm thick MS(IS 2062 Grade E250/350), sheets complete with approved artistic profile and decorative shape as per drawing include CNC / laser cut patterns, including Mor-Pankh and artistic ornamental motifs on Shaft backed with UV-stabilized milky polycarbonate / acrylic diffuser pole with proper structural strength, stability & free from any deformation. The decorative CNC / laser cut portions of arms shall be internally illuminated with IP-67 (3000K Warm White) Flexible Neon silicon profile Flexible Silicon neon strip will be square in shape 14x14mm having minimum 6 Watt per meter, 12V DC operated, complete with all required fixing accessories and suitable capacity Heavy Duty IP-67 HPF drivers / SMPS housed inside the service window for outdoor use.• The approximate total Neon LED Strip length shall be 16Mtr per pole +/- 10%, complete for full illumination of decorative ornamental arms.• 03 Nos. 1 Watt LED Spot Lights, IP-65, aluminum body, warm white, shall be mounted at approved decorative locations as shown in drawing. •Provision for an internal termination box with a 4-way heavy-duty connector and 3 Nos. 6 Amp SP MCB (10kA). •The pole shall also include complete mounting arrangement, housing, support frame, cut- out and internal route for wiring at both arm ends for installation of 150 Watt Flush Mounted Decorative LED Street Light; however, 150W LED street light fixtures / luminaires themselves shall not be included in this item. •The complete pole shall be finished with proper surface cleaning & surface preparation, anti-corrosive primer, UV-stabilized powder coating micron not less than 80 micron, and final approved Artistic High-Gloss Exterior PU Paint Finish in combination of Royal Blue and Golden shades, including multicolour artistic paint Highlighting on Peacock feathers and ornamental motifs, or as approved by Engineer-in-Charge. • Final shades, artistic pattern detailing, and finish quality of the pole shall be finalized based on an approved prototype sample prior to commencement of bulk production. The scope of the item shall include provision of all labour, T&P, consumables, welding, fitting, proper alignment, erection, testing, commissioning, and all incidental works necessary for complete and satisfactory installation of the pole system. |
| 15 | Compressive Operation and Maintenance के कार्य को सफलतापूर्वक सम्पादित करने पर द्वितीय वर्ष की अवधि के पश्चात् Part -A के अन्तर्गत सम्पादित कार्य की कुल राशि की 0.50 प्रतिशत राशि की दर से भुगतान किया जायेगा। |
| 16 | Compressive Operation and Maintenance के कार्य को सफलतापूर्वक सम्पादित करने पर तृतीय वर्ष की अवधि के पश्चात् Part -A के अन्तर्गत सम्पादित कार्य की कुल राशि की 0.75 प्रतिशत राशि की दर से भुगतान किया जायेगा। |
| 17 | Compressive Operation and Maintenance के कार्य को सफलतापूर्वक सम्पादित करने पर चतुर्थ वर्ष की अवधि के पश्चात् Part -A के अन्तर्गत सम्पादित कार्य की कुल राशि की 1.0 प्रतिशत राशि की दर से भुगतान किया जायेगा। |
| 18 | Compressive Operation and Maintenance के कार्य को सफलतापूर्वक सम्पादित करने पर पंचम वर्ष की अवधि के पश्चात् Part -A के अन्तर्गत सम्पादित कार्य की कुल राशि की 1.0 प्रतिशत राशि की दर से भुगतान किया जायेगा। Please Enable Macros to View BoQ information |
