|
| 1 | Taking down storage type water heater from wall by disconnecting the electric connection and water inlet/outlet connection from main and repairing the water heater storage type capacity 25/50 ltrs of any type and make, at site complete all as specified & directed by Engineer-in-charge. |
| 2 | Refixing storage type water heater storage type capacity 25/50 ltrs of any type and checking the serviceablity of all parts of such as inner vesser, rubber gasket, non return valve, heating element, thermostat etc and refixing the same after replacing of unserviceable parts and assembly completet (considered as one unit) and installing and testing the same as per the direction of Engineer-In-Charge.Note :- Supply only for parts against unserviceable parts shall be measured and paid for separately under relavent items given below) |
| 3 | Supply & Fix including taking out for heating elements, 1.5/2 KW ISI mark 230 volts complete all as specified & directed by Engineer-in-charge. |
| 4 | Supply & Fix including taking down for thermostat immersion point ,Length 175 mm to 250 mm , Temperature 0 to 75 degree C , 230 volts/AC complete all as specified & directed by Engineer-in-charge. |
| 5 | Supply & Fix including taking down for replacement of safety valve for 25/50 ltr geyser complete all as specified & directed by Engineer-in-charge. |
| 6 | Supply & Fix including taking down for replacement of pressure releasing valve for 25/50 ltr geyser complete all as specified & directed by Engineer-in-charge. |
| 7 | S&F in repair connecting sheet metal enclosure with two pin and earth metal clad plug and socket complete, with one double pole MCB 20 Amp complete all as specified & directed by Engineer-in-charge. |
| 8 | Supply & Fix including taking down for Three pin plug top, 16 amp capacity, 240 V AC, heavy duty complete all as specified & directed by Engineer-in-charge. |
| 9 | Supply & Fix including taking down for MCB SP 16 Amps single pole,B curve, 230volt, 50 Hz complete all as specified & directed by Engineer-in-charge. |
| 10 | Supply & Fix including taking down for Fastners screw for fixing Geyser storage capacity 25/50 ltrs of any type and make complete all as specified & directed by Engineer-in-charge. |
| 11 | Supply & Fix including taking down for replacement of PVC connection pipe duly chromium plated 8 mm dia both end threaded incl brass coupling bolt cone washer complete , length of pipe is not less than 450 mm suitable for Hot/ cold water system complete all as specified & directed by Engineer-in-charge. |
| 12 | Supply & Fix including taking down for replacement of PVC connection pipe duly chromium plated 8 mm dia both end threaded incl brass coupling bolt cone washer complete , length of pipe is not less than 600 mm suitable for Hot/ cold water system complete all as specified & directed by Engineer-in-charge. |
| 13 | Supply & Fix including taking down for replacement of indicator lamp assembly for geyser complete all as specified & directed by Engineer-in-charge. |
| 14 | Supply & Fix including taking down for replacement of 3 core PVC insulated and sheathed cable with copper conductor of size 40/0.076 complete all as specified & directed by Engineer-in-charge. |
| 15 | Supply & Fix including taking down for replacement of inlet & outlet assembly plate suitable for 25 ltrs capacity geyser as per existing pattern complete all as specified & directed by Engineer-in-charge. |
| 16 | All as per serial item No. 16 but 50 Ltrs |
| 17 | Supply & Fix including taking down for Inner tank of geyser of 25 Ltr capacity of made out of steel tank in replecement of leakage tank of geyser complete all as specified & directed by Engineer-in-charge. |
| 18 | All as per item No. 17 for 50 Ltr |
| 19 | Supply & Fix including taking down for STOP COCK cast copper alloy, screwed down high pressure screwed both ends for iron pipe of 15 mm bore fancy type chromium plated complete all as specified & directed by Engineer-in-charge. |
| 20 | S & F including taking down for Bib tap chromium plated 15 mm dia cast copper alloy with butter fly handle, screwed down, screwed one ends for pipe of 15 mm dia complete all as specified & directed by Engineer-in-charge. |
| 21 | M&L for servicing of ETC/FPC type solar water heater of any capacity including taking down ,cleaning and descaling of tubes,refixing of tubes,checking and prevention of any leakages,functioning of NRV & gate valves,cleaning of stainless steel hot water tank, checking and repair the heating coil connections, functioning of thermostst etc complete all as specified & directed by Engineer-in-charge.Note :- Defective items replaced will be measured under respective items. |
| 22 | Dismantling old defective FPC solar water heater collector of any type any make complete all as specified & directed by Engineer-in-charge. |
| 23 | S&F MNRE registered/approved polyester powder coated solar water heater Flat plate collector with high transmitive clear toughened glass glazing having absorber material as headers, risers and fins made up of 99.9% pure copper with selective black chrome coating with ultra sonic laser permanent bonding between copper fins & tubesell with inlet and outlet connections with collector top and bottom leg complete suitable for 500 LPD with minimum one year warranty complete all as specified & directed by Engineer-in-charge. |
| 24 | S&F MNRE registered/approved polyester powder coated solar water heater Flat plate collector with high transmitive clear toughened glass glazing having absorber material as headers, risers and fins made up of 99.9% pure copper with selective black chrome coating with ultra sonic laser permanent bonding between copper fins & tubesell with inlet and outlet connections with collector top and bottom leg complete suitable for 300 LPD with minimum one year warranty complete all as specified & directed by Engineer-in-charge. |
| 25 | S&F MNRE registered/approved polyester powder coated solar water heater Flat plate collector with high transmitive clear toughened glass glazing having absorber material as headers, risers and fins made up of 99.9% pure copper with selective black chrome coating with ultra sonic laser permanent bonding between copper fins & tubesell with inlet and outlet connections with collector top and bottom leg complete suitable for 200 LPD with minimum one year warranty complete all as specified & directed by Engineer-in-charge. |
| 26 | S&F MNRE registered/approved polyester powder coated solar water heater Flat plate collector with high transmitive clear toughened glass glazing having absorber material as headers, risers and fins made up of 99.9% pure copper with selective black chrome coating with ultra sonic laser permanent bonding between copper fins & tubesell with inlet and outlet connections with collector top and bottom leg complete suitable for 150 LPD with minimum one year warranty complete all as specified & directed by Engineer-in-charge. |
| 27 | S&F MNRE registered/approved polyester powder coated solar water heater Flat plate collector with high transmitive clear toughened glass glazing having absorber material as headers, risers and fins made up of 99.9% pure copper with selective black chrome coating with ultra sonic laser permanent bonding between copper fins & tubesell with inlet and outlet connections with collector top and bottom leg complete suitable for 100 LPD with minimum one year warranty complete all as specified & directed by Engineer-in-charge. |
| 28 | Taking down of Old U/S hot water tank of any capacity any make complete all as specified & directed by Engineer-in-charge. |
| 29 | S & F MNRE registered/approved 500 LPD non pressurised FPC stainless steel hot water tank with inner tank material SS 304 with outer cladding of painted & oven baked pre coated galvanised sheet, insulated with 40mm thick high density PUF insulation with thermostat and heater coil 2/3 KW and suitable size of MS powder coated stand 32x3 mm angle frame with required PCC work 1:2:4 for foundation/fixing complete all as specified & directed by Engineer-in-charge. |
| 30 | S & F MNRE registered/approved 300 LPD non pressurised FPC stainless steel hot water tank with inner tank material SS 304 with outer cladding of painted & oven baked pre coated galvanised sheet, insulated with 40mm thick high density PUF insulation with thermostat and heater coil 2/3 KW and suitable size of MS powder coated stand 32x3 mm angle frame with required PCC work 1:2:4 for foundation/fixing complete all as specified & directed by Engineer-in-charge. |
| 31 | S & F MNRE registered/approved 200 LPD non pressurised FPC stainless steel hot water tank with inner tank material SS 304 with outer cladding of painted & oven baked pre coated galvanised sheet, insulated with 40mm thick high density PUF insulation with thermostat and heater coil 2/3 KW and suitable size of MS powder coated stand 32x3 mm angle frame with required PCC work 1:2:4 for foundation/fixing complete all as specified & directed by Engineer-in-charge. |
| 32 | S & F MNRE registered/approved 150 LPD non pressurised FPC stainless steel hot water tank with inner tank material SS 304 with outer cladding of painted & oven baked pre coated galvanised sheet, insulated with 40mm thick high density PUF insulation with thermostat and heater coil 2/3 KW and suitable size of MS powder coated stand 32x3 mm angle frame with required PCC work 1:2:4 for foundation/fixing complete all as specified & directed by Engineer-in-charge. |
| 33 | S & F MNRE registered/approved 100 LPD non pressurised FPC stainless steel hot water tank with inner tank material SS 304 with outer cladding of painted & oven baked pre coated galvanised sheet, insulated with 40mm thick high density PUF insulation with thermostat and heater coil 2/3 KW and suitable size of MS powder coated stand 32x3 mm angle frame with required PCC work 1:2:4 for foundation/fixing complete all as specified & directed by Engineer-in-charge. |
| 34 | S & F MNRE registered/approved 200 LPD non pressurised ETC stainless steel hot water tank with inner tank material SS 304 with outer cladding of painted & oven baked pre coated galvanised sheet, insulated with 40mm thick high density PUF insulation with 20 tube holes of 58mm diameter and outer PPGI with 20 Nos of 58x1800 mm tubes , thermostat and heater coil 2 KW and suitable size of MS powder coated stand 25x3 mm angle frame with required PCC work 1:2:4 for foundation/fixing complete all as specified & directed by Engineer-in-charge. |
| 35 | S & F MNRE registered/approved 150 LPD non pressurised ETC stainless steel hot water tank with inner tank material SS 304 with outer cladding of painted & oven baked pre coated galvanised sheet, insulated with 40mm thick high density PUF insulation with 15 tube holes of 58mm diameter and outer PPGI PUF insulation with 15 Nos of 58x1800 mm tubes with thermostat and heater coil 2 KW and suitable size of MS powder coated stand 32x3 mm angle frame with required PCC work 1:2:4 for foundation/fixing complete all as specified & directed by Engineer-in-charge. |
| 36 | S & F MNRE registered/approved 100 LPD non pressurised ETC stainless steel hot water tank with inner tank material SS 304 with outer cladding of painted & oven baked pre coated galvanised sheet, insulated with 40mm thick high density PUF insulation with 10 tube holes of 58mm diameter and outer PPGI with 10 Nos of 58x1800 mm tubes with thermostat and heater coil 2 KW and suitable size of MS powder coated stand 32x3 mm angle frame with required PCC work 1:2:4 for foundation/fixing complete all as specified & directed by Engineer-in-charge. |
| 37 | S&F tubes of Evacuated tube collector (ETC) type 1800mm long tubes with inner dia 47mm and outer dia 58mm with frame and frame angle 30 degree complete all as specified & directed by Engineer-in-charge. |
| 38 | S&F tubes of Evacuated tube collector (ETC) type 2100mm long tubes with inner dia 47mm and outer dia 58mm with frame and frame angle 30 degree complete all as specified & directed by Engineer-in-charge. |
| 39 | Taking down old U/S , broken pipe of any type any size complete all as specified & directed by Engineer-in-charge. |
| 40 | Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete of size 20mm including union, bends and tees complete all as specified & directed by Engineer-in-charge. |
| 41 | S&F including taking down for heating element for solar water heating system of capacity 2/3 KW complete all as specified & directed by Engineer-in-charge. |
| 42 | S&F including taking down for thermostat 3 KW suitable for 100 to 500 litres capacity of solar water heater complete all as specified & directed by Engineer-in-charge. |
| 43 | Dismantling & taking out the unserviceable Gun-metal, globe or gate valves of any size from geyser/solar connection pipe complete all as specified and directed by Engr-In-Charge. |
| 44 | S&F for Gun-metal, globe or gate valves, with iron wheel head ,screwed both ends from iron pipe and fixed size 15 mm complete all as specified & directed by Engineer-in-charge. |
| 45 | All as per Serial Item No 44.00 above but size 20 mm complete all as specified & directed by Engineer-in-charge. |
| 46 | All as per Serial Item No 44.00 above but size 25 mm complete all as specified & directed by Engineer-in-charge. |
| 47 | S&F including taking out Ball brass valves,high pressure,with polythene float valve 20mm and flynut complete,screwed for iron pipe complete all as specified & directed by Engineer-in-charge. |
| 48 | S&F Non return valve of 20/25 mm dia complete all as specified & directed by Engineer-in-charge. |
| 49 | Supply & Fix including taking down for rotational moulded synthetic (HDPE) water storage tank of capacity of 1000 litre capacity triple layered, cylindrical vertical with closed top hoisted and fixed in position all as specified in SSR Part-I complete all as specified & directed by Engineer-in-charge. |
| 50 | Supply & Fix including taking down for rotational moulded synthetic (HDPE) water storage tank of capacity of 500 litre capacity triple layered, cylindrical vertical with closed top hoisted and fixed in position all as specified in SSR Part-I complete all as specified & directed by Engineer-in-charge. |
| 51 | S & F including taking out for GI tubing 20 mm dia medium grade galvanised with necessary fittings such as tees, elbows, bends, reducers, union etc laid in wall ceiling & Floor including all fittings complete all as specified & directed by Engineer-in-charge. |
| 52 | S & F including taking out for GI tubing 15 mm dia medium grade galvanised with necessary fittings such as tees, elbows, bends, reducers, union etc laid in wall ceiling & Floor including all fittings complete all as specified & directed by Engineer-in-charge. |
| 53 | S & F including taking down sheet metal single pole and neutral enclosure with a two pin and eath plug and socket complete with one single pole MCB 20 Amp 240 V complete all as specified & directed by Engineer-in-charge. |
| 54 | M&L for submain wiring with approved colour code/as per IS (Red, black & green for single phase) circuit with two single core PVC insulated cable with multistranded copper coductor of nominal cross sectional area of 6.0 Sqmm (FRLSH) in existing concealed /surface conduit non metallic including one run of PVC insulated multistranded copper conductor nominal cross section area of 6.0 Sqmm (FRLSH) of continuous earth wire green in colour including taking down old u/s sub-main wiring complete all as specified and directed by Engineer-in-charge.Note: Two runs of 6.0 Sqmm cable & One run of 6.0 Sqmm cable shall be paid as one unit length. |
| 55 | M&L for submain wiring with approved colour code/as per IS (Red, black & green for single phase) circuit with two single core PVC insulated cable with multistranded copper coductor of nominal cross sectional area of 6.0 Sqmm (FRLSH) in through incl concealed conduit non metallic including one run of PVC insulated multistranded copper conductor nominal cross section area of 6.0 Sqmm (FRLSH) of continuous earth wire green in colour including taking down old u/s sub-main wiring complete all as specified and directed by Engineer-in-charge.Note: Two runs of 6.0 Sqmm cable & One run of 6.0 Sqmm cable shall be paid as one unit length. |
| 56 | S & F for sheet metal enclosure MCB SPN DB 8 way IP 43 with 200 Amps rated bus bar 240 volts double door with magnitic locking system complete all as specified & directed by Engineer-in-charge. Make : Legrand Cat pot No 507611 or equivalent list of makes |
| 57 | S & F for sheet metal enclosure MCB SPN DB 4 way IP 43 with 200 Amps rated bus bar 240 volts double door with magnitic locking system complete all as specified & directed by Engineer-in-charge. Legrand Cat pot No 507610 or equivalent list of makes |
| 58 | S & F for sheet metal enclosure MCB SPN DB 2 way 240 volts sngle door with magnitic locking system complete all as specified & directed by Engineer-in-charge. |
| 59 | Supply and fixing MCB's single pole and neutral 25/32 Amps, 240 Volts,10 KA rapturing capacity 'C' curve complete all as specified & directed by Engineer-in-charge. |
| 60 | Taking down of old U/S rusted MS structure of solar water tank any type any shape complete all as specified & directed by Engineer-in-charge. |
| 61 | Taking down of old U/S rusted MS structure of cold water tank any type any shape complete all as specified & directed by Engineer-in-charge. |
| 62 | S&F compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like includind caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates grade Fe-290 (Gde E-165), including all lattice bars, stiffeners, gusset plates etc welded together, anchor duly painted with two coats of synthetic enamel paint over and coat of red oxide primer and and forming PCC work and 12mm thick etc complete to avoid any deformation complete all as specified & directed by Engineer-in-charge. |
| 63 | M&L for taking down carefully existing aluminium/ copper point wiring (light, fan, socket or power) complete fittings fixture such as switches Ceiling roses, pendents,regulators, sockets etc to be measured separately)unscrewing from Board/outlet boxes, fittings & fixtures such as switches, sockets, ceiling rose lamp holder tube/ceiling fitting, bulk head fittings, tube lights & regulator etc and making good disturbed surfaces of walls, floors etc complete all as specified & directed by Engineer-in-charge. Please Enable Macros to View BoQ information |
| 64 | M&L for taking down carefully existing aluminium/ copper point wiring (light, fan, socket or power) complete fittings fixture such as switches Ceiling roses, pendents,regulators, sockets etc to be measured separately)unscrewing from Board/outlet boxes, fittings & fixtures such as switches, sockets, ceiling rose lamp holder tube/ceiling fitting, bulk head fittings, tube lights & regulator etc and making good disturbed surfaces of walls, floors etc complete all as specified & directed by Engineer-in-charge. Please Enable Macros to View BoQ information |
