Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | M&L Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 2 | M&L for cleaning and preparing the surfaces to be welded together, holding the members in true position while welding and bevelling of edges, thickness of metal to be welded exc 3 mm but n exc 6 mm complete all as specified and directed. (Note : Taking down the article and refixing in position after welding shall be measured separately) |
| 3 | M&L for cleaning and preparing the surfaces to be welded together, holding the members in true position while welding and bevelling of edges, thickness of metal to be welded exc 6 mm but n exc 9 mm complete all as specified and directed. (Note : Taking down the article and refixing in position after welding shall be measured separately) |
| 4 | M&L for Fe 410-W (Gde E-250 quality A) Framed work as in doors or gates of angle or other section with gusset plates,rails,braces etc complete,drilled for fixing of steel sheeting or other covering. Doors,etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening anf fixing complete all as specified and directed. |
| 5 | M&L Mild steel, plain, 1.25 mm thick sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed. |
| 6 | M&L Mild steel, plain, 1.25 mm thick sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required including dismantling of plain sheet complete all as specified and directed. |
| 7 | Taking down shutter of any description exc 1 sqm but n exc 2 sqm each and removing to store complete all as specified and directed. |
| 8 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 9 | Taking down chowkhat or frames n exc 1.50 Sqm each with shutters (without taking off shutters from the frame) and removing to store complete all as specified and directed |
| 10 | Taking down chowkhat or frames exc 1.50 Sqm and n exc 4 Sqm each with shutters (without taking off shutters from the frame) and removing to store complete all as specified and directed |
| 11 | Taking down shutter of any description area exceeding 1 sqm but n exc 2 sqm each and removing to store complete all as specified and directed. |
| 12 | Taking down shutter of any description area not exceeding 1 sqm each and removing to store complete all as specified and directed. |
| 13 | Taking down shutter of any description not exceeding 1 sqm each leaf and refixing, in same opening after easing and adjusting building hard ware etc complete all as specified and directed |
| 14 | Taking down shutter of any description exceeding 1 sqm but not exiding 2 Sqmeach leaf and refixing, in same opening after easing and adjusting building hard ware etc complete all as specified and directed |
| 15 | S&F aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples complete all as specified and directed. |
| 16 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet re-inforced with MS square tube in opening as per specification and shown on drg SSR Part-II 2020. |
| 17 | S&F, factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain cover PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top rails lock rail and bottom rail on either side & as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and jointed together with solvent cement , as per specification and shown on drawing in SSR Part-II (2020). |
| 18 | S&F mild steel flat iron as in bands straps, supports or stays for rainwater, ventilating pipes including bolt if required, hooks (stay) heavy for large gates,hook and pintle hinges,large hasps and staples, brackets for WHB, hold fasts, wall ties, hooks for hanging fans ,cleats for securing purlins to wood trusses or rafters and similar small articles conforming to Fe -290 Gde E-165 complete all as specified and directed. |
| 19 | S&F 150 mm long aluminium anodised, barrel tower bolts of extruded section and fixed etc complete all as specified and directed. |
| 20 | S&F 100 mm long aluminium handles cast type, anodized complete all as specified and directed |
| 21 | S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed |
| 22 | S&F 75 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed |
| 23 | S&F 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed |
| 24 | S&F in repair 100 mm long aluminium anodized handles fabricated type complete all as specified and directed |
| 25 | S&F in repair 150 mm long aluminium anodised, barrel tower bolts of extruded section and fixed etc complete all as specified and directed. |
| 26 | S&F in repair 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed |
| 27 | S&F in repair 75 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed. |
| 28 | S&F in repair 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed. |
| 29 | S&F 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed. |
| 30 | S&F in repairs 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed. |
| 31 | Hacking out old broken glass (any thickness, size quality or description) form wooden frames or stone, concrete or brick surrounds glazed with oil putty or fixed with beads complete all as specified and directed. |
| 32 | S&F 3 mm thick sheet glass ordinary quality and gazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and directed. |
| 33 | S&F 3 mm thick figured glass pin headed type and gazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and directed. |
| 34 | S&F in repairs aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples complete all as specified and directed. |
| 35 | Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be miteredcut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing withselected quality glass. (Note: The unit rate quoted by contractor includes cost of glass and panel and includes all other connected accessories) |
| 36 | Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm),Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of wateretc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor includes cost of glass and includes all other connected accessories.) (Area not exceeding 2.00 sqm) |
| 37 | Providing and fixing factory made uPVC white colour fixed or lovoured window/ ventilator made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glass (Note: The unit rate quoted by contractor includes cost of glass and includes all other connected accessories) (Area not exceeding 1 sqm each) |
| 38 | Supply and fix factory made uPVC Door Espag complete all as specifed and directed |
| 39 | Supply and fix factory made uPVC Lever Door Handle complete all as specifed and directed |
| 40 | Supply and fix factory made uPVC Standard Cylinder complete all as specifed and directed |
| 41 | Supply and fix factory made uPVC Centre Striker complete all as specifed and directed |
| 42 | Supply and fix factory made uPVC 3D Hinge complete all as specifed and directed |
| 43 | Supply and fix factory made uPVC Striker complete all as specifed and directed |
| 44 | Supply and fix factory made uPVC Drainage complete all as specifed and directed |
| 45 | Supply and fix factory made uPVC Glazing Bridge complete all as specifed and directed |
| 46 | Supply and fix factory made uPVC Silicon Sealant complete all as specifed and directed |
| 47 | S & F Powder coated three track Aluminium sliding window with frame not less than 1.8 mm thick excluding aluminium grill and including 4 mm thick tinted glass, beading & necessary rubber packing, locking & opening arrangement, all fitting and fixture complete all as specified and directed. |
| 48 | S&F Powder coated (Minimum thickness of Powder Coating 50 micron) Aluminium doors with frame (sliding or otherwise) with or without 12 mm thick prelaminated particle board, exterior grade, prelaminated both sides with decorative choice laminations, thickness of powder coated aluminium member not less than 1.8 mm thick & 5 mm thick tinted selected glass including bedding and necessary rubber packing, 150 mm aluminium handle,150 mm tower bolt in its all fitting and fixture, mortice lock 4 lever etc complete all as specified and directed. |
| 49 | S&F 7mm thick aluminium grills of make \\"Decogrill' model DG 104 surrounded by aluminium 'C' channel with mesh size 75 X 75mm all as specified and directed. |
| 50 | Demolition of brickwork built in cement or cement lime mortar including all quoins, arches pillar etc complete all as specified and directed. |
| 51 | M&L Brick work with flyash bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 52 | Taking down cement or cement lime plaster, of any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 53 | M&L for Rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) complete all as specified and directed. |
| 54 | M&L for rendering 5 mm thick in CM 1:3 on RCC ceiling surface and finished even and smooth with out using extra cement complete all as specified and directed . |
| 55 | M&L for applying 2mm thick Birla / JK Putty in two layers on newly plastered wall surfaces absolutely even and smooth, rubbing with sand paper complete all as specified and directed. |
| 56 | M&L for applying 2mm thick Birla / JK Putty in two layers on old wall surfaces including complete removal of existing wall finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper complete. |
| 57 | M&L for applying 2mm thick Birla / JK Putty in two layers on newly plastered ceiling surfaces absolutely even and smooth, rubbing with sand paper complete all as specified and directed. |
| 58 | M&L for applying 2mm thick Birla / JK Putty in two layers on old Ceiling surfaces including complete removal of existing Ceiling finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper complete all as specified and directed. |
| 59 | M&L for applying two coats of oil bound distemper on wall or concrete surfaces over & including a coat of primer on prepared surfaces including, rubbing with sand paper complete all as specified and directed. |
| 60 | M&L for applying two coats of oil bound distemper on Ceiling surfaces over & including a coat of primer on prepared surfaces including, rubbing with sand paper complete all as specified and directed. |
| 61 | M&L for preparation of newly plastered surfaces of walls and apply three coat of white wash complete all as specified and directed. |
| 62 | M&L for preparation of newly plastered surfaces of ceilings and apply three coat of white wash complete all as specified and directed. |
| 63 | M & L for two coats of cement based paint over a coat of primer on new plastered surface of walls including preparation of surface complete all as specified and directed. |
| 64 | M&L applying two coats Cement based paint on old decorated wall surfaces, includes complete removal of existing wall finish of any type with wire brush, brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc complete all as specified and directed. |
| 65 | M&L applying two coats of acrylic exterior weather proof emulsion paint over a coat of exterior primer on newly plastered wall surfaces/ old decorated wall surfaces, in case of old decorated wall surfaces includes complete removal of existing wall finish of any type with wire brush, brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc complete all as specified and directed. |
| 66 | M&L for Complete removal of existing treatment and applying two coats of OBD over a coat of alkali resistant primer on wall complete all as directed by Engineer-in-Charge. |
| 67 | M&L preparation of old painted surfaces and applying one coat of white wash on walls complete all as specified and as directed. |
| 68 | M&L preparation of old painted surfaces and applying one coat of white wash but on ceiling complete all as specified and as directed. |
| 69 | M&L preparation of old painted surfaces and applying one coat of oil bound distemper on walls complete all as directed. |
| 70 | Removing old paints by paint removes or burning off by blow lamps and cleaning with scrapers, any number of coats,any width or girth complete all as specified and directed. |
| 71 | M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 72 | M&L for preparation of old wood or wood based surfaces of any description, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 73 | M&L preparation of old decorated wooden painted surfaces of any description not other wise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 74 | M&L for preparation of old steel surfaces of any description, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 75 | M&L preparation of old decorated Steel painted surfaces of any description not other wise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 76 | M&L for two coats synthetic enamelled paint to new steel surfaces after preparation over a coat of red oxide primer area over exc 10cm in width or girth etc complete all as specified and directed. |
| 77 | M&L for two coats synthetic enamelled paint to new steel surfaces after preparation over a coat of red oxide primer area over exc 10cm in width or girth etc complete all as specified and directed. |
| 78 | M&L preparation of new steel surfaces of any description n exc 10cm in width or girth and priming with red oxide zinc chrome and applying two coat of synthetic enamel paint complete all as specified and as directed. |
| 79 | M & L for Preparation of plastered surface including a coat of primer on prepared surfaces including, rubbing with sand paper and applying Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50gms/litre, of approved manufacturer, ofrequired shade and colour complete, as per manufacturer's specification. Two or more coats |
| 80 | S&F in repairs 18/19 mm thick high density PVC/ WPC solid fibre board with prelaminated PVC sheet as Kitchen cupboard and frame including taking down the old cupboard shutters and removing to store complete all as specified and directed. |
| 81 | S&F continuous (piano) hinges of width of flaps (when open) 30 mm, mild steel, bright finish or electrogalvanised complete all as specified and directed. |
| 82 | S & F magnetic catcher catcher with nut and screw of mild steel bright finish all as specified and directed. |
| 83 | S & F 40 mm dia cupboard knobs fixed with nuts screw and washer of mild steel bright finish complete all as specified and directed. |
| 84 | S & F in repair 40 mm dia cupboard knobs fixed with nuts screw and washer of mild steel bright finish complete all as specified and directed. |
| 85 | S & F in repair hasp and stapple safety type aluminium anodised 75 mm long with mild steel hinge pin including bolt to hinge plate fixed with screw complete all as specified and directed. |
| 86 | S&F in repairs door closer hydraulically regulated designation No 2, universal type, suitable for door shutter of weight between 36 to 60 Kg of aluminium (Die cast) body complete all as specified and directed. |
| 87 | S&F Flush shutters 35 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sidescomplete all as specified and directed. |
| 88 | M&L Second class hard wood 30 mm thick factory made glazed and skeleton shutters, open rebated and prepared to receive glass , gauze etc with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR part I section 8 clause 8.24 (a) complete all as specified and directed. |
| 89 | M&L Second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed. |
| 90 | S&F Plain, framed,panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board edium density, wood particle board with commercial face veneers: supplied and fitted to chowkats |
| 91 | S&F 35mm 1st class teak hardwood plain, framed,panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board edium density, wood particle board with commercial face veneers: supplied and fitted to |
| 92 | S&F Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkat. |
| 93 | S& F Skeleton shutter, open rebated and prepared to receive glass , guaze etc divided into squares made with 19 mm thick ply along with 12 mm glass , door spring & mortice lock with 12 mm thick plywood frame with finishing of veneer sheet wit complete polish all as specified and directed |
| 94 | S& F frame made out of with 12 mm thick plywood with finishing of veneer sheet with complete polish all as specified and directed |
| 95 | M&L 16 to 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. |
| 96 | S&F in repairs door closer hydraulically regulated designation No 2, universal type, suitable for door shutter of weight between 36 to 60 Kg of aluminium (Die cast) body complete all as specified and directed. |
| 97 | S&F in repairs Aluminium Mortice lock 2 lever, vertical type, size 100 mm with escutcheon plates and two keys complete all as specified and directed. |
| 98 | S&F in repairs Aluminium Mortice lock 4 lever, vertical type, size 100 mm with escutcheon plates and two keys complete all as specified and directed. |
| 99 | M&L Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed |
| 100 | M&L At points of contact of wood work by chemical emulsion (in oil or kerosenebased solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed. |
| 101 | S&F 12 mm thick toughened glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required and pivot at top fancy type SS handle of size not less than 300 mm on both sides of shutter with suitable locking arrangement and all necessary fitting complete all as specified and directed. |
| 102 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement. |
| 103 | Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs /blankets, any thickness, including cover fillets complete all as specified and directed. |
| 104 | S&F 12 mm thick plain Gypsum Board False Ceiling with GI frame including all necessary drilling cutting to fix electric items complete all as specified and directed with following:- (a) GI Grid channel 30x25x20 mm of 24 gauge fixed with rawl plug and screw 450 mm centre to centre alongwith perimeter walls. (b) GI channel made to shape 50x40x40 mm of 24 gauge placed @ 600 mm centre to centre from perimeter at wall except long wall (in one span). (c) GI intermediate runners of size 45x10x10 mm of 24 gauge fixed @ 1200 mm centre to centre leaving frame of one side walls (in other span). (d) GI sheet 25 mm wide and 20 mm gauge suspended fixed with steel fastner to roof ceiling and 1200 mm centre to centre including pluging of RCC Slab. (e) 12 mm thick gypsum board filling joints with POP and finishing complete with two coat of plastic emulsion paint over one coat of primer on ceiling. |
| 105 | S & F Anodised aluminium snap grid frame work size 605mm x 605mm for false ceiling all as specified |
| 106 | S &F Hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long (removing old hangers) complete all as specified |
| 107 | M&L 6mm thick Exposed metal frame ceiling with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid (Frame work for ceiling shall be measured and paid separately) complete all as specified and directed |
| 108 | M&L Water proofing treatment on \\"Non approachable / non accessible and approachable roof\\" surface (Horizontal & Vertical surfaces) in following sequence through manufacturer / authorized applicator of the manufacturer including taking down of existing roof treatment, properly cleaning & drying the concrete surfaces complete (i) Applying a coat of oxidised bitumen based solvent primer @ 0.3 Kg / Sqm (ii) Applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 kg/ Sqm incl cleaning surfaces complete all as specified and directed. (iii) Laying evenly over the bitumen coated surface, polymeric water proofing membrane Hyperplas standard wt not less than 3kg /Sqm with 100 mm over laps shall be sealed by flame as per manufacturers instruction complete all as specified and directed. (iv) Applying two coats of bituminous aluminium paint including preparation complete all as specified and directed by Engr-in-Charge/GE. |
| 109 | M&L for PCC 1:2:4 type B0 (Using 12.50 mm graded stone aggregate) in roof padding/ kerbs/ sunken slab etc complete all as specified and directed by Engr-in-Charge. |
| 110 | M&L 10 mm thick rendering on roof surfaces/ concrete surface in CM 1:4 with liquid water proofing compound @ 200 ml per 50 Kg cement complete all as specified and directed. (Waterproofing compound should be measured and paid separately). |
| 111 | S & F in repair bevelled edge Looking mirror of any size without frame of selected quality glass mounted on wall with chromium plated stainless screws complete all as specified and directed |
| 112 | M&L dismantling boarding , any description fixed with screws in any position complete all as specified and directed. |
| 113 | M&L PVC wall lining consisting of 5 mm thick single side prelam PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified and directed. |
| 114 | M & L for 5 mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as specified and directed. |
| 115 | Taking down carefully copper/aluminium point wiring (light,fan,bell, socket or power) complete,including fixtures and fittings such as switches, ceiling roses, holders,regulators, sockets, tube light fittings i.e removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made for conditions separately ) and including making good the disturbed surfaces to match with existing surface and colour shade with proper putty for smooth finishing without andulations complete all as specified and directed.( Note:- All credit materials should be deposited in MES yard as available on work site the same materials should be issued to contractor through gate pass as per contract schedule of credit materials against contract agreement or taken on ledger with approval by accepting officer). |
| 116 | Material and labour for cutting chasing,pinning of brick/ stone/concrete wall at any height wall cutting and chases for concealed wiring for 20/25 mm PVC conduit dia pipe,water tubing,etc and making good to facings where required and pointing in cement motor 1:3 to ends or edges of landigs,wall surfaces etc,cutting not exc 10 cm girth and including making good the disturbed surfaces to match with existing surface and colour shade with proper putty for smooth finishing with existing wall complete all as specified and directed |
| 117 | M&L for point wiring using approved colour coding incl providing circuit wiring with 1.5 sqmm PVC insulated, FRLSH type, ISI marked,conf to IS-694/1990 unsheathed, multistranded, single core, copper cable 1100 volts grade cables drawn through in PVC Conduit 20/25 mm dia medium grade ISI marked (MMS) at any height/places and all accessories are concealed in walls / roofs / floors / ceiling etc. including suitable arrangements for flush mounting modular MS/GI boxes as per site requirement/suitable for modular top cover and frame for fixing of modular switches,sockets,fan regulators, blank plate etc and including 1.5 Sqmm PVC insulated multistranded FRLSH type unsheathed(Green colour),single core cable with copper cable as earth continuity conductor and connecting to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour shade with necessary putty for smooth finishing complete all as specified and directed for the following:- (a) One light point controlled by one 10amps switch. |
| 118 | (b) One fan point controlled by one switch 10 amps, and one regulator. |
| 119 | (c) One exhaust fan point controlled by one 10 amps switch . |
| 120 | (d) One 5 pin 6 amps socket point controlled by one 10 amps switch on independent board . |
| 121 | (e) One 5 pin 6 amps socket point controlled by one 10 amps switch on same board . |
| 122 | (f) One bell/buzzer point controlled by one bell push. |
| 123 | (g) One light point controlled by two 2 way switches/bed switch point |
| 124 | All as per item No.120 & 121 above,but point wiring with 2.5 sqmm and earth conductor of size 2.5 sqmm incl circuit wiring complete all as specified and directed for the following:-(a) One 6 pin 16/6 amps socket outlet point controlled by one 16/20 amps switch on independent board. |
| 125 | (b) One 6 pin 16/6 amps socket outlet point controlled by one 16/20 amps switch on same board. |
| 126 | All as per item No.121 above ,but point wiring with 4.0 sqmm and earth conductor of size 4 sqmm incl circuit wiring complete all as specified and directed. |
| 127 | M&L for point wiring using approved colour coding incl providing circuit wiring with 1.5 sqmm PVC insulated, FRLSH type, ISI marked,conf to IS-694/1990 unsheathed, multistranded, single core, copper cable 1100 volts grade cables drawn through PVC casing and caping 20/25 mm width double locking medium grade ISI marked (MMS) at any height and all accessories such as Tee,bend,short piece & elbow on surface on walls / roofs / floors / ceiling etc. including providing suitable arrangements for flush mounting modular MS boxes as per site requirement/suitable for modular top cover and frame for fixing of modular switches,sockets,fan regulators, blank plate etc and including 1.5 Sqmm PVC insulated multistranded FRLSH type unsheathed(Green colour),single core cable with copper cable as earth continuity conductor and connecting to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour shade with necessary putty for smooth finishing complete all as specified and directed for the following: (a) One light point controlled by on switch |
| 128 | (b) One fan point controlled by one switch and regulator |
| 129 | (c) One exhaust fan point controlled by one switch. |
| 130 | (d) One 5 pin 6 amps socket point controlled by one 6 amps switch on independent board . |
| 131 | (e) One 5 pin 6 amps socket point controlled by one 6 amps switch on same board . |
| 132 | (f) One bell point controlled by one bell push. |
| 133 | (g) One light point controlled by two 2 way switches. |
| 134 | All as per item No.130 & 131 above,but point wiring with 2.5 sqmm and earth conductor of size 2.5 sqmm and incl providing circuit wiring complete all as specified and directed for the following:- (a) One 6 pin 6/16 amps socket outlet point controlled by one 16 amps switch on independent board. |
| 135 | (b) One 6 pin 6/16 amps socket outlet point controlled by one 16 amps switch on same board. |
| 136 | All as per item No.134 above ,but point wiring with 4.0 sqmm and earth conductor of size 4 sqmm incl providing circuit wiring complete all as specified and directed. |
| 137 | Supply & fixing and fixing in repairs modular type switch 10 Amps, single pole,1way,1 module,240V,AC, ISI Marked complete all as specified and directed by Engr-in-Charge. |
| 138 | Supply & fixing and fixing in repairs modular type switch 10 Amps ,2way,single pole,1 module,240V,AC, ISI Marked complete all as specified and directed by Engr-in-Charge. |
| 139 | Supply & fixing and fixing in repairs modular type bell push 6 Amps,1 module, single pole, 240 volts,AC, ISI Marked complete all as specified and directed by Engr-in-Charge. |
| 140 | Supply & fixing and fixing in repairs modular type switch 16 Amps, single pole,1way,1 module,240V,AC, ISI Marked complete all as specified and directed by Engr-in-Charge. |
| 141 | Supply & fixing and fixing in repairs modular type socket shuttered type 6 Amps, 2/3 Pin combined 2 module,240V,AC ISI Marked complete all as specified and directed by Engr-in-Charge. |
| 142 | Supply & fixing and fixing in repairs modular type socket 6 A/16 Amps, 6 Pin combined shuttered socket 2 module,240V,AC ISI Marked complete all as specified and directed by Engr-in-Charge |
| 143 | Supply & fixing and fixing in repairs red color lighting indication lamp 6 Amps, single pole,240volts,AC,50 Hz suitable for 1 module ISI Marked complete all as specified and directed by Engr-in-Charge. |
| 144 | Supply & fixing and fixing in repairs modular type step fan speed regulator 120W, 2 module,230volts,AC, 360 degree rotation 0 to 4/5 steps, ISI Marked complete all as specified and directed by Engr-in-Charge. |
| 145 | Supply & fixing and fixing in repairs call bell AC, 230 Volts single pole, multi music type ISI marked, complete all as specified and directed by Engr-in-Charge. |
| 146 | Supply & fixing and fixing in repairs call bell ding dong AC, 230 Volts single pole, multi music type ISI marked, complete all as specified and directed by Engr-in-Charge. |
| 147 | Supply & fixing and fixing in repairs angle lamp holder, insulated body with back plate for batten fittings complete all as specified and directed by Engr-in-Charge. |
| 148 | Supply & fixing and fixing in repairs ceiling rose, 3 terminal ,PVC/polycarbonate body ISI marked, complete all as specified and directed by Engr-in-Charge. |
| 149 | Supply & fix decorative box type 20 watt light fitting,blue coloured end caps, pre-wired and including providing single/double side LED tubelight(tube rod) white/warm 20 watt-01 No made of aluminium extrusion with high efficient LED driver,IP-20, including PVC/Wooden round/square block -02 Nos and connected with LED fitting to ceiling rose and including removing old unserviceable fitting complete all as specified and directed by Engr-in-Charge. |
| 150 | Supply & fix decorative box type 9 watt light fitting,blue coloured end caps, pre-wired providing single side LED tube 9 watt-01 No, and including PVC/Wooden round/square block -02 Nos and connected with LED fitting to ceiling rose and including removing old unserviceable fitting complete all as specified and directed by Engr-in-Charge. |
| 151 | Supply and fixing, in repairs 20 watt LED pride plus batten white decorative type,high quality materials,240V,50Hz, and slim integrated body,easy to install,,PC diffuser and connected with LED fitting to ceiling rose terminal and incl removing old unserviceable fitting complete all as specified and directed by Engr-in-Charge. |
| 152 | Supply & fixing, in repairs 40 watt LED light fitting white lighting, high quality materials and intergrated design, PC diffuser, reliable and robust housing structure, easy to install, efficency 125 lm/w necessary arrangements for fixing with LED fitting to ceiling rose complete all as specified and directed by Engr-in-Charge. |
| 153 | S & F Energy efficient and energy saving new generation 10 watts LED bulk head light fitting IP-65 luminaire with opel diffuser pre-wired of luminaires including LED light driver and connected with LED fitting to ceiling rose terminal and incl removing old unserviceable fitting complete all as specified and directed by Engr-in-Charge. |
| 154 | Supply & fixing , in repairs LED bldg secruity light fitting sensor based of capacity 35 Watt LED street light fitting in aluminium PDC housing, toughened glass cover with IP65 protection and including removing of old unserviceable item complete all as specified and directed by Engr-in-Charge. |
| 155 | Supply and fix GI bracket pipe of size 25 to 32 mm dia as suitable medium grade of 1.2 mtr long bent to shape suitable degree of bending as per site requirement with hot or cold bending method of process for making the one end of GI pipe bracket suitable for fixing of any type street light fitting and shall be fixed on wall surfaces and including providing suitable fabricate galvanised flat iron clamps of 20X4 mm thick -02 Nos suitable for fixing at any place/height with hole fastners,nuts,bolts & washers including grouting on wall etc and including removing of old unserviceable item complete all as specified and directed by Engr-in-Charge. |
| 156 | Supply & fixing , in repairs in sheet metal enclosure, 415 volts AC,TPN DB, 4 way,8+12 modules, flush mounting with copper busbar, 2 neutral/earth bars links and MCB incomer, and MCB SPN/SP/TPN as outgoing and complete for IP43&54 DBs protection and including removing old unserviceable DBs and incl making good the disturbed surfaces to match with existing surface and colour shade complete all as specified and as directed by Engr-in-Charge. |
| 157 | Supply & fixing , in repairs in sheet metal enclosure, double door ,415 volts AC,VTPN DB, 4 way,8+12 modules, flush mounting copper busbar, 2 neutral/earth bars links and MCCB incomer, and MCB SPN/SP/TPN as outgoing and complete for IP43&54 DBs protection and including removing old unserviceable DBs and incl making good the disturbed surfaces to match with existing surface and colour shade complete all as specified and as directed by Engr-in-Charge. |
| 158 | Supply & fixing , in repairs sheet metal enclosure, double door, 240 volts AC,SPN,DB, 12 way, flush mounting with 100amps copper busbar,neutral bar,earth bar links and MCB incomer MCB SPN/DP and MCB SP as outgoing for IP 43& IP54 DBs protection nd including removing old unserviceable DBs and making good the disturbed surfaces to match with existing surface and colour shade acomplete all as specified and as directed by Engr-in-Charge. |
| 159 | Supply & fixing in repairs sheet metal enclosure, double door, 240 volts AC,SPN,DB, 8 way, flush mounting with 100amps copper busbar,neutral bar,earth bar links and MCB incomer MCB SPN/DP and MCB SP as outgoing for IP 43& IP54 DBs protection nd including removing old unserviceable DBs and making good the disturbed surfaces to match with existing surface and colour shade acomplete all as specified and as directed by Engr-in-Charge. |
| 160 | Supply & fix and fixing in repairs and sheet metal enclosure, with acrylic type double door, 240 volts AC,SPN,DB, 4 way, flush mounting with 100amps copper busbar,neutral bar,earth bar and MCB incomer,MCB SPN/DP, and MCB SP as outgoing for IP 43& IP54 DBs protection nd including removing old unserviceable DBs making good the disturbed surfaces to match with existing surface and colour shade complete all as specified and as directed by Engr-in-Charge. |
| 161 | Supply & fix and fixing in repairs MCB SP 6 to 32 Amps 10 KA,\\"C\\" series,AC,240Volts,50Hz , ISI marked and including removing old unsv items complete all as specified and directed by Engr-in-Charge. |
| 162 | Supply & fix and fixing in repairs MCB SPN 32 to 40 Amps 10 KA,\\"C\\" series,AC,240Volts,50Hz, ISI marked and including removing old unsv items complete all as specified and directed by Engr-in-Charge. |
| 163 | Supply & fix and fixing in repairs MCB SPN 40 to 63 Amps 10 KA,\\"C\\" series,AC,240Volts,50Hz, ISI marked and including removing old unsv items complete all as specified and directed by Engr-in-Charge. |
| 164 | Supply & fix and fixing in repairs MCB TPN 40 to 63/100 Amps 10 KA,\\"C\\" series,AC,440Volts,50Hz, ISI marked and including removing old unsv items complete all as specified and directed by Engr-in-Charge. |
| 165 | M & L for sub main wiring complete in repairs with 2 run of 10 sqmm single core copper conductor (ISI marked)cable 1100 volts grade, ISI marked,FRLSH type (conforming to IS-694/1990 as amended) PVC insulated, unsheathed,flexible,multi stranded colour coded cables drawn drawn through and including PVC conduit in concealed ISI marked medium grade(MMS) accessories such as Tee,corner, overlaping connector etc and including one run of 10 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade, ISI marked,FRLSH type as earth continuity conductor connected to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour shade and complete all as specified and directed.Note : - Two run of 10 sqmm single core copper conductor cable and one run of 10 sqmm single core copper conductor cable as earth continuity and one run of PVC conduit shall be measured as one unit. |
| 166 | All as per ditto item No 165 but 2 run x 6 sqmm+1 run earth wire complete all as specified and directed. |
| 167 | All as per ditto item No 165 but 2 run x 4 sqmm+1 run earth wire complete all as specified and directed. |
| 168 | All as per ditto item No 165 but 2 run x 2.5 sqmm+1 run earth wire complete all as specified and directed. |
| 169 | All as per ditto item No 165 but 2 run x 1.5 sqmm+1 run earth wire complete all as specified and directed. |
| 170 | Supply & fix and fixing in repairs suitable for flush mounting sheet steel enclosure metal clad plug and socket including MCB SP 20 Amps, 10KA 'C 'series, 230 Volts,50Hz suitable for AC's/Geysers complete all as specified and directed by Engr-in-Charge. |
| 171 | Supply & fix and fixing in repairs MCCB, 125 Amps,4 pole,415 Volts , 16/18KA thermal magnetic type with necessary lugs,thimbles, nuts bolts and washers and including removing old unserviceable item complete all as specified and as directed by Engr-in-Charge. |
| 172 | Material and labour for earthing complete with galvanised steel earth plate electrode 600mmX 600mmX 6mm thick buried directely in ground vertically ( earth pit not less than 2.25 metres deep below ground level) with top edge of plate not less than 1.5 metres below ground level, connected to and including galvanised iron strip of size 32 X 6 mm from earth electrode to test point or up to 7.5mtr whichever is less by means of GI bolts, nuts, check nuts and washers all as per electrical plate no 3 of SSR Pt-I and GI watering pipe of 20 mm dia medium grade,GI funnel with wire mesh,including char coal, salt packed all around the earth electrode plate in layers,PCC earth pit chamber 1:3:6 type C1,RCC cover 1:2:4 type B1, including excavation,earth work in any strata and returning filling, removal of surplus soil and testing for required value complete all as specified and directed. |
| 173 | S&F for PVC non-metalic rigid conduit incl boxes,junctions boxes 1 to 4 way & terminals but incl of all tees,bends,elbows,reducers,bell mouth tube ends and fixing accessories such as couplers lock nuts,saddles,pipes hookes etc ISI marked heavy duty of size 20/25 mm dia for LAN,telephone and TV connections cablesincluding cutting,chasses and making good disturbed surfaces to match with existing surfaces with plaster/putty and including removing of old unserviceable item complete all as specified and directed. |
| 174 | Supply & fix and fixing in repairs copper conductor cable, PVC insulated, sheathed,flexible, multistranded,ISI marked, 1100 volts grade 3 core ;2.5 sqmm and including electric connection through PVC conduit in concealed/casing caping in surface from ceiling fan to ceiling rose and including removing old unserviceable item complete all as specified and directed by Engr-in-Charge. |
| 175 | Supply & fix and fixing in repairs 40 watts LED post top lantern made in cast aluminium spigot housing with decorative opal polycarbonate diffser and IP65 protection and providing suitable fixing arrangements ,nuts,bolts and washers and including removing old unserviceable item complete all as specified and directed by Engr-in-Charge. |
| 176 | Supply & fix and fixing in repairs LED flood light light fitting of capacity 120 Watt LED, light fitting in aluminium PDC housing, toughened glass cover with IP-65 protection and including removing of old unserviceable item complete all as specified and directed by Engr-in-Charge. |
| 177 | Supply & fix and fixing in repairs LED flood light light fitting of capacity 100 Watt LED, light fitting in aluminium PDC housing, toughened glass cover with IP-65 protection and including removing of old unserviceable item complete all as specified and directed by Engr-in-Charge. |
| 178 | Supply and fixing and in repairs galvanised metal flush box 1/2 module, ISI marked,and suitable for existing type as per site requirement and including removing old unserviceable item from existing loaction complete all as specified and as directed by Engr-in-Charge. |
| 179 | All as per item No-178 ditto but meteal box 3 module |
| 180 | All as per item No-178 ditto but meteal box 4/5 module |
| 181 | All as per item No-178 ditto but meteal box 6 module |
| 182 | All as per item No-178 ditto but meteal box 8/9 module |
| 183 | All as per item No-178 ditto but meteal box 12 module |
| 184 | All as per item No-178 ditto but meteal box 16 module |
| 185 | All as per item No-178 ditto but meteal box 18 module |
| 186 | Supply and fixing in repairs modular white/wood/glazed type cover plate with frame 1 module,ISI marked and suitable for existing type as per site requirement and incl screws,washears etc and including removing old unserviceable item from existing loaction complete all as specified and as directed by Engr-in-Charge. |
| 187 | All as per item No-186 ditto but modular white/wood/glazed type cover plate with frame 2 module |
| 188 | All as per item No-186 ditto modular white/wood/glazed type cover plate with frame 3 module |
| 189 | All as per item No-186 ditto but modular white/wood/glazed type cover plate with frame 4/5 module |
| 190 | All as per item No-186 ditto modular white/wood/glazed type cover plate with frame 6 module |
| 191 | All as per item No-186 ditto but modular white/wood/glazed type cover plate with frame 8/9 module |
| 192 | All as per item No-186 ditto but modular white/wood/glazed type cover plate with frame 12 module |
| 193 | All as per item No-186 ditto but modular white/wood/glazed type cover plate with frame 16 module |
| 194 | All as per item No-186 ditto butmodular white/wood/glazed type cover plate with frame 18 module |
| 195 | Supply and fix in repairs of PVC/bakalite sheet round cover blanking plate as per site requirement with screws of existing fan junctions/ wiring junctions boxes etc |
| 196 | M&L for preparation of new plastered of wall/ceiling or concrete surface of walls or concrete and applying two coats of 3 mm thick wall care putty complete all as specified and directed |
| 197 | M&L for preparation of old decorated surface of wall and apply two coats of white wash complete all as specified and directed |
| 198 | Fixing only and connecting electric meters 10-60 Amps any type single or three phase complete all as specified and directed and including providing necessary accessories complete all as specified and as directed. |
| 199 | Taking down carefully existing electric meters of any type/capacity from work site and deposit to MES store yard/ Charge holder without damage for safe custody and supply and fixing single phase electronic meters temper proof LCD display with polycarbonate cover 230Volts,10-60 Amps, accuracy class-I,50Hz, confirming to IS-13779,IP-54,with parameters to show data,time current reading,load,PF,voltage and KWH including connected necessary items for functioning complete all as specified and directed. |
| 200 | Supply & Fixing of SITC of LED Patient bed head light with Up-Down twin side glow 20W+20W batten type wall mounted luminaire. CCT 6500K (CW) on down side & 3000K (WW) on up side & total system lumen not less than 2000Lm on each side. Color Rendering Index (CRI) ≥80, long life of 35000hrs of operation, Fully diffused optics with eye comfort technology, Inbuilt electronic driver, PF >0.90 and THD <20% with operating voltage 160-270V AC, 50Hz. Inbuilt surge protection minimum 2.5 KV, complete in all specified and directed by Engr-in-charge. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
