|
| 1 | Providing, fiting, testing and commisioning of grade sp 320/140 2.1 KLPM Air Blower with 2hp motor of standard make ISI mark coupled with suitable 3 phase induction electric motor complete with auxilary pipe system upto filter beds with pressure guage, nozzels, air check valve ,non return valve ,starter etc - all complete |
| 2 | Providing & fixing CI gate valve 150mm dia (6”) gate Valve,for drainage and backwash. |
| 3 | Supply and filling of filter media from approved source - Gravel (Graded gravel - size ranging from 2.0mm to 40.00 mm), and Sand (Coarse filter sand - in filter beds alongwith mesh/strainer. Including all carriages, complete job. 3m x 1.5m x 2m |
| 4 | Desilting of filter beds by manual means and disposal of material as directed by engineer incharge |
| 5 | Supplying, installation & commissioning of Motors 0.5hp monoblock impeller 3 phase with gear system /madhani system for alum and bleaching dosing system, |
| 6 | Supplying, installation & commissioning 5 HP monoblock motor , Suction 4”, delivery 3”alongwith starter. |
| 7 | Supplying, installation of Mushrom valve 3” for back wash and air. |
| 8 | Supplying, installation of Alum gauge flow meter with necessary items. |
| 9 | Supplying, installation of Bleaching gauge flow meter with necessary items. |
| 10 | Desiliting/dewatering/cleaning of sedimentation tank Complete job |
| 11 | Providing & fixing CI gate valve 100mm(4”) dia |
| 12 | Providing & fixing MS Flanges 100mm |
| 13 | Providing & fixing MS Flanges 150mm |
| 14 | Providing & fixing MS Bends 100mm |
| 15 | Providing & fixing MS Bends 150mm |
| 16 | Providing & fixing Water level gauge (buble type) outside PST |
| 17 | Supplying Alum non ferric |
| 18 | Supplying High quality Bleaching powder with atleast 30- 34% available chlorine for effective water disinfection |
| 19 | Providing & fixing Main distribution pannel Switch board (Havels) 415 v 3 phase |
| 20 | Providing & fixing 3” brass gate valve |
| 21 | Providing & fixing CI (75mm) 3” gate valve |
| 22 | Providing & fixing CI Foot valve 100mm ( 4”) |
| 23 | Supplying, installation & commissioning of Starter 20 hp 3 phase |
| 24 | Supplying, Nut bolt with washer of required size |
| 25 | Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required in chequered plate wherever required, all complete. |
| 26 | Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA)conforming to IS - 1536 :100 mm dia pipe, for water distribution system |
| 27 | Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In frames, guard bar, ladder and similar works. |
| 28 | Providing, fabricating and supplying shadow box of required size and shape, for fixing in the spandrel portion of the structural glazing, in linear as well as curvilinear portions of the building by providing semi - rigid, inorganic, non-combustible fibre glass wool insulation 50 mm thick, conforming to IS: 8183 and BS: 3958 Part 5. The insulation layer shall have facing (factory bonded on surface # 1of the fibre glass insulation layer), of black nonwoven fibre glass tissue of nominal thickness 0.5 mm and nominal mass not less than 60 gm / sqm, made of randomly oriented glass fibres distributed in a binder by a wet-lay process including fixing 1.5 mm thick solid aluminum sheet backing using, 6 mm thick cement board including SS rivets, nuts, bolts, washers etc complete |
| 29 | Providing Hard drawn steel wire fabric 25 x 25 mm mesh of weight not less than 7.75 kg/sqm |
| 30 | Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded |
| 31 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 32 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade, one or more coats on old work. |
| 33 | Supplying Gasket sheet conforming to I.S. 5382 of good Quality |
| 34 | Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge: All kinds of soil |
| 35 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 36 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand) |
| 37 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15°,landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to five level including curing but excluding the cost of centering, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 38 | Centering and Shuttering including strutting, propping etc. And removal of form work for: Suspended floors,walls |
| 39 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Zsections and other sections of approved make conforming to IS: 733 andIS: 1285, fixed with dash fastener of required dia. and size includingnecessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing offittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately.) Anodized aluminum (Anodized transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15). For bathroom Door & ventilator |
| 40 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-I type-II) in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-incharge.Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side/float glass for ventilator. |
| 41 | CEMENT PLASTER (IN FINE SAND) 12mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand) |
| 42 | Supply of following GI accessories : G.I Pipe 15mm |
| 43 | Socket 15 mm |
| 44 | GI Union 15 mm |
| 45 | GI TEE 15 mm |
| 46 | Extension nipple (size 15mmx50mm) |
| 47 | Long Nose bib cock 15 mm |
| 48 | Engagement of Plumber for installation of supplied accessories. Plumber |
| 49 | Engagement of Helper with plumber. Helper |
| 50 | Supply of following electrical items: 1.50 sqmm make Havells or equivalent |
| 51 | 4.0 sqmm make Havells or equivalent for Geysor point |
| 52 | LED bulb 9 W make Havells or equivalent |
| 53 | Exhaust Fan 12 inches make Havells or equivalent |
| 54 | Combine switch socket 16 amp make Havells or equivalent |
| 55 | Engagement of electrical fitter for installation work of electric items |
| 56 | Providing and laying Ceramic glazed tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete.In colour such as White, Ivory, Grey, Fume Red Brown |
| 57 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 58 | Making soak pit 2.5 m diameter 3.0 meter deep with 45x45 cm dry brickhoney comb shaft with common burnt clay (non modular) bricks of class designation 7.5 bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 59 | Centering and shuttering including strutting, propping etc. and removal of form work for walls (any thickness) including attached pilasters buttresses, plinth and string course fillets, kerbs andsteps etc. |
| 60 | Carriage: A)cement avg lead 15KM |
| 61 | Sand avg lead 125KM |
| 62 | Agregate avg lead 15KM |
| 63 | Bricks per 1000Nos avg lead 90KM Please Enable Macros to View BoQ information |
