|
| 1 | 2.6.1.Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge. All kinds of soil |
| 2 | 4.1.3. Providing and laying in position cement concrete of specified grade excluding thecost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 3 | 4.1.8.Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand(zone-III) : 8 graded stone aggregate 40 mm nominal size). |
| 4 | 10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes |
| 5 | 9.48.1 Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding |
| 6 | 50.6.1.4. Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete. |
| 7 | 13.2.1. 15 mm cement plaster on the rough side of single or half brick wall of mix:1:4 (1cement :4 fine sand) |
| 8 | 12.51.3. Providing and fixing precoated galvanised steel sheet roofing accessories 0.350 mm(+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screwscomplete: |
| 9 | 21.1.1.1. Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portionAnodised aluminium (anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15) |
| 10 | LMR. Supply and fixing UV stabilized sheet of th 200 microns, UV stabilised, light transmission: 86%, light diffusion: 55 %, anti dust and anti drip. Make as GINAGER plastic ldt ISREAL. Including cost and conveyance of all amterials and labour charge and complete as directed by engineer in charge ( Market rate) |
| 11 | LMR.Providing and fixing shade net of 50 % black/green tape type colour red, monofilement light diffusing net 90 GSM thick |
| 12 | LMR. Providing and laying weed mat in rainshelter including labour transportation etc. 80 GSM |
| 13 | Providing and fixing irrigation facilities like PP screen filter 50mm x 25 cum KP120 mesh , pressure gauge 250 GLZ 8 bar 25mm BSP, air vaccum release valve AV 10 25 mm, barber start 16, rubber grommet dia 400mm 10.7 mm, spnt flt 07/L/H 60 cm W/STB , PP ball valve 63 mm PVC flush valve 63 mm and 63 mm pvc pipe and 50 mm pipe including labour and transportation charges. Please Enable Macros to View BoQ information |
