|
| 1 | M&L for de-watering and taking out sludge / algae / vegitation from SWTs of any size and removing sludge and cleaning the SWTs ,complete all as specified & as directed by Engr-in-Charge. |
| 2 | Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) floors, aprons etc ,complete all as specified & as directed by Engr-in-Charge. |
| 3 | M&L for opening out cracks, making V grooves, removing the loose material and Filling with Dr Fixit Crack -X shrink free ,complete all as specified & as directed by Engr-in-Charge. |
| 4 | M&L for concrete surface is thoroughly cleaned once again using wire brush and after that applying One liberal coat of Make Fosroc Nitobond EP / or equivalent- two component Epoxy bonding agent shall be brush applied to the parent concrete ,complete all as specified & as directed by Engr-in-Charge. |
| 5 | M&L for nominal mix PCC 1:2:4 using 40mm graded stone aggregate as in flooring or mass concreting, complete all as specified and as directed by Engr-in-charge. |
| 6 | M&L for providing and applying of Dr Fixit / Fosroc / Equivalent exterior acrylic polyurethene elastomeric coating in 2 coats complete all as specified.(a) Apply initial layer of polyurethene elastomeric coating over cement slurry over concrete work (b) After 1 Hrs of drying of initial layer apply 2nd layer of polyurethene elastomeric coating in perpendiculer direction to 1st coat.(c) After that sprinkling the quartz sand over the coating for better adhesion of the next layer of protective screed..Note : (a) Recommend Coverage rate is approximately 1.1 kg./m2/coat for 1 mm. (Minimum 2 coat.). (b) Allow the slurry to cure for at least 15-30 min. before applying second coat. Do not leave the first coat to dry longer than 8 hours. |
| 7 | M&L for Screed bed 15mm thick in CM (1:4) on fair faces of brickwork or concrete surfaces or for protection of PU coating, finished even and smooth (without using extra cement) complete all as specified and directed. |
| 8 | M&L for water proofing treatment on wall / concrete surface and applying 2 coats of Dr Fixit Rain coat exterior acrylic elastomeric coating ,complete all as specified & as directed. (Note:- seepage/dampness portion of bldgs only considered for measurement) |
| 9 | M&L for Providing, cement concrete type C1 1:3:6 (using 20mm graded stone aggregate) in plinth courses, string courses, lacing courses, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angle,complete all as specified & as directed |
| 10 | Site clearance in any type of soil ,complete all as specified and as directed by Engr-in-charge. |
| 11 | M&L for 7.5cm thick (compacted thickness) WBM, with coarse aggregates granite, trap and basalt of grading 2 (63 to 40mm size) or of grading 3 (50 to 20mm size), spread, rolled and consolidated to gradient and camber required ,complete all as specified and as directed by Engr-in-charge. |
| 12 | M&L for Applying evenly a priming/tack coat with paving bitumen bituminous primer at 10 kg per 10 sq metre ,complete all as specified and as directed by Engr-in-charge. |
| 13 | M&L for Premix bituminous, macadam with paving bitumen any penetration laid/rolled and compacted to required gradient and camber (consolidated thickness 40mm or less) ,complete all as specified and as directed by Engr-in-charge. |
| 14 | M&L for Bituminous premix asphaltic dense concrete 40mm consolidated thickness with 6% binder with paving bitumen content by weight of total mix, rolled and compacted to required camber and gradient ,complete all as specified and as directed by Engr-in-charge. |
| 15 | Supplying, installation, commissioning and testing of open well submersible motor 5 HP BEE 5 Star rating, electic driven, 50 metre head in load,discharge range 4.5 LPS,Model No KOS-550+, suitable for pumping raw water, complete all as specified and directed and comprising of the following specifications:-(i) submersible motor horizontal type discharge dia 50 mm Suction 65 mm, at 50 metre head, 3000 RPM having bronze impeller and stainless steel shaft single stage directly (ii) Including suitable size of foundation with angle iron for installation of above pump set duly drilled holes and painted with two coats of synthetic enamel paint over a coat of red oxide primer Make :- Kirloskar Brothers Ltd / Beacon / KSB / JyotiNote:- Sluice valve and reflux valve, DI pipe and fittings etc. required for suction and delivery and common header etc. shall be measured and paid separately in respective items. Please Enable Macros to View BoQ information |
| 16 | Supplying, installation, commissioning and testing of open well submersible motor 5 HP BEE 5 Star rating, electic driven, 50 metre head in load,discharge range 4.5 LPS,Model No KOS-550+, suitable for pumping raw water, complete all as specified and directed and comprising of the following specifications:-(i) submersible motor horizontal type discharge dia 50 mm Suction 65 mm, at 50 metre head, 3000 RPM having bronze impeller and stainless steel shaft single stage directly (ii) Including suitable size of foundation with angle iron for installation of above pump set duly drilled holes and painted with two coats of synthetic enamel paint over a coat of red oxide primer Make :- Kirloskar Brothers Ltd / Beacon / KSB / JyotiNote:- Sluice valve and reflux valve, DI pipe and fittings etc. required for suction and delivery and common header etc. shall be measured and paid separately in respective items. Please Enable Macros to View BoQ information |
