Tender For Special Repair To Building No P-58 (Or Md Accn) And Allied Works At Rakhmuthi Mil Stn Under Ge (S) Akhnoor.
Tender Value
39.80 Lakhs
Estimated cost
Bid Submission
07 Jul 2026
2 days left
EMD
79600
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
akhnoor → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Building No P-58 (Or Md Accn) And Allied Works At Rakhmuthi Mil Stn Under Ge (S) Akhnoor.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling of mild steel work of any description, complete all specified and directed. |
| 2 | Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and as directed. |
| 3 | M&L for brick work with sub class 'B' bricks old size straight or curved in plane exc 6m mean radius built in cement mortar 1:6, complete all as specified and directed. |
| 4 | Description all as per Serial item No.3 here in above, but except brick, complete all as specified and directed. |
| 5 | Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. |
| 6 | M&L for rendering 10 mm thick in cement mortar 1:6 on any surfaces of brick work or concrete surfaces, finished even & smooth without using extra cement, complete all specified and directed. |
| 7 | M&L for rendering 15 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces, finished even & smooth without using extra cement,complete all specified and directed.Note:- Cost for rendering upto double storey height shall be deemed included in quoted area. |
| 8 | M&L for preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion over one coat of primer over two coats of wall care putty, complete all as specified and as directed by Engineer-In-Charge. |
| 9 | M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement based paint over a coat of primer , complete all as specified and as directed. |
| 10 | M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of exterior emulsion paint (Apex) over a coat of primer, complete all as specified and as directed. |
| 11 | M&L for preparation of old/ decorated, un-decorated, plastered or unplastered surfaces of walls including complete removal of existing treatment and applying two coats of distemper oil emulsion over one coat of primer over two coats of wall care putty, complete all as specified and as directed by Engineer-In-Charge.. |
| 12 | M&L for preparation of old/ decorated, un-decorated, plastered or unplastered surfaces of walls including complete removal of existing treatment and applying two coat of cement based paint, complete all as specified and as directed by Engineer-In-Charge. |
| 13 | M&L for complete removal existing treatment from old surface of walls and applying two coats of exterior emulsion paint (Apex Ultima or equivalent), over one coat of primer including preparation of old surfaces, complete all as specified and as directed by Engineer-In-Charge. |
| 14 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed. |
| 15 | M&L for 25mm thick cement concrete in sub bases, floors type B-1, 1:2:4 (20mm graded crushed stone aggregate), finishing concrete surface even and fair without using extra cement, complete all as specified and directed by Engineer-In-Charge. |
| 16 | M&L for non-skid ceramic coloured tiles of size 400x400 mm and 7 to 8 mm thick, set and jointed in neat cement slurry (3 Kg cement per Sqm) and pointed in white or coloured cement to match over screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar 1:6, complete all as specifed and directed. |
| 17 | M&L for non-skid ceramic coloured tiles of size 600x600 mm 7 to 8 mm thick, set and jointed in neat cement slurry (3 Kg cement per Sqm) and pointed in white or coloured cement to match over screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar 1:6, complete all specified and directed. |
| 18 | M&L for non-skid ceramic coloured tiles of size 600x600 mm 7 to 8 mm thick, set and fixing in skirting/dado or any other vertical surfaces and pointed in white or coloured cement to match and including 10mm thick for laying floor finishes in cement mortar 1:4, complete all specified and directed. |
| 19 | M&L for glazed ceramic coloured designer pattern tiles 450mmx 300mmx7mm thick on vertical surface such as skirting, dado etc. set and pointed in white colour cement, including rendering 10mm thick on fair faces of brick work or concrete surface in cement mortar 1:4 as backing coat for tiles, complete all as specified and directed. |
| 20 | M&L for machine cut kota stone slab, minimum size shall be (550x550mm), flooring 16-18mm thick laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with beeswax polish (mirror finish) complete, over and including screed bed or bedding layer of mortar 20mm thick in cement morat 1:3, complete all as specified and as directed. |
| 21 | M&L for machine cut kota stone slab, (size shall in one length), 16-18mm thick, as in riser of steps, skirting, dado and pillar, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete, and including laid over screed bed or back plastering layer of mortar 15mm thick in cement mortar 1:4, complete all as specified and as directed by Engineer-In-Charge. |
| 22 | M&L for black granite (of any type) 16-18mm work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite over and over 20mm thick screed bed in cement mortar 1:3, complete all as specified and as directed. |
| 23 | M&L for green marble work (of any type) 16-18mm work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with marble shade of following types, complete all as specified and as directed. |
| 24 | Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level), complete all as specified and directed. |
| 25 | M&L for providing plain cement concrete M-10 (1:3:6) type C-1, ( using 20mm graded crushed stone aggregate), 75mm thick as in plinth protection laid in bays not exceeding 2 Sqm each and finishing the surface even and fair on top without using extra cement with 6mm wide joints throughout the thickness of plinth protection in concrete bays and in between the walling and plinth protection, filling the joints with mastic filling comprising of one part of heated bitumen 85/25 grade and 3 parts of sand ( all by weight), complete all as specified and as directed. |
| 26 | Taking down chowkhat or frame with shutters (without taking off shutters from frames) exc. 1.5 Sqm but n.exc 4 Sqm each, complete all as specified and directed by Engineer-In-Charge. |
| 27 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 Sqm each, complete all as specified and directed by Engineer-In-Charge. |
| 28 | M&L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., size of frame 125x60mm, complete all as specified and as directed . |
| 29 | Providing & Fixing factory made 100% solid WPC (Wood Polymer Composite) door frame 125x65mm double rebated made from wood polymer composite (single extruded process) material comprising of virgin PVC polymer of K value 57-60 (suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat hust) and non toxic additives fabricated with meter joint after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm, having good crew holding capacity (screw withdrawl stregth of (Min. 990 N), minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite / borer proof, water / moisture proof & fire retardant & fixed in position with SS dash fasteners/ hold fast of required dia and length, all as per specification drawings as directed by the Engineer-in-Charge. |
| 30 | M&L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., size of frame 105x60mm, complete all as specified and as directed. |
| 31 | Providing & Fixing factory made 100% solid WPC (Wood Polymer Composite) door frame 100x65mm double rebated made from wood polymer composite (single extruded process) material comprising of virgin PVC polymer of K value 57-60 (suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat hust) and non toxic additives fabricated with meter joint after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm, having good crew holding capacity (screw withdrawl stregth of (Min. 990 N), minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite / borer proof, water / moisture proof & fire retardant & fixed in position with SS dash fasteners/ hold fast of required dia and length, all as per specification drawings as directed by the Engineer-in-Charge. |
| 32 | S&F for aluminium powder coated (minimum thickness of powder coating 50micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified and as directed. |
| 33 | S&F for aluminium powder coated anodised aluminium window, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including galvanised mild steel wire cloth, 0.46 mm nominal dia of wire and average width of aperture 1.18mm , including anodised aluminium grill of mesh size 70mm x70 mm and thickness 3-4 mm (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21 100mm long (2 No.)suitable handle (1 No.) (thickness of powder coating should not less than 50 micron) each measured seperately, complete all as specified and as directed by Engineer-in-Charge. |
| 34 | S&F for 5.0 mm frosted sheet glass, ordinary quality fixed in windows in square n exc 0.5 Sqm in each pane fixed in aluminium partion, complete all as specified and as directed . |
| 35 | S&F for 40 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with both faces covered with decorative face veneer with lipping/frame to match complete all as specifed and directed. |
| 36 | S&F for 25mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with both faces covered with decorative face veneer with lipping/frame to match complete all as specifed and directed. |
| 37 | S&F for 40 mm thick flush shutter prepared to receive glass/ wire cloth, etc. (in 2 panels n. exc 0.4 sqm each) with sash bars, solid core construction, with block board core and plywood face panels, commercial type on both sides with both faces covered with decorative face veneer with lipping/frame , including stainless steel wire cloth, 0.46mm nominal dia of wire and average width of aperture 1.18mm etc.; supplied and fitted to chowkhats, complete all as specified and as directed . |
| 38 | S&F for solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rein forced with M.S. square tube supplying and fixing in opening as per specification and drawing, complete all as specified and directed by Engineer-In-Charge. |
| 39 | S&F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in the mild steel frame welded etc. with suitable PVC sheet beading and jointing etc, complete all as specified and directed by Engineer-In-Charge. |
| 40 | S&F for factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2,4, or 6 raised panel design with 2mm thick Moulded PVC sheet on front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification, complete all as specified and as directed by Engineer-in-Charge. |
| 41 | M&L for 5-6 mm thick ACP (Aluminium Composite Panel) sheet as in kitchen cupboard partition, complete all as specified and as directed by Engineer-In-Charge. |
| 42 | M&L for 16-18mm thick pre laminated both sides MDF(Medium Density Fibreboard) as in kitchen shelf including fittings like auto hinge, continious hinge, handle complete all as specified and as directed. |
| 43 | M&L for mild steel framed work such as in grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; staging for of water tanks, cooler stand and similar work conforming to Fe-290, Gde-E-165, including cutting and welding and taking down existing steel, complete all as specified and as directed. |
| 44 | S&F for TMT bars of 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders and binding with and including mild steel wire (annealed) not less than 0.9 mm dia., complete all as specified and as directed. |
| 45 | S&F for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips, complete all as specified and as directed. |
| 46 | M&L for formwork to flat finished surface of concrete to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, chajja, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed. |
| 47 | M&L for reinforcement cement concrete (nominal mix) type B-1 ,1:2:4 (20 mm graded crushed stone aggregatge) for Chajjas/Balcony/Landing work/kitchen slab etc, complete all as specified and as directed. |
| 48 | S&F in repair for curtain rod, 20 mm dia chromium plated mild steel fixed with brakets, stops, rollers etc., complete all as specified and as directed. |
| 49 | M&L for applying two coats of synthetic enamel paint over a coat of zinc chrome/red oxide primer including preparation of new or previously untreated steel surfaces over 10 cm in width or girth, complete all as specified and as directed. |
| 50 | M&L for preparation of old painted steel surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat (finishing coat) of synthetic enamel paint, complete all as specified and as directed. |
| 51 | S&F for 100 mm long extruded aluminium alloy handle, cast type, anodised ISI marked, complete all as specified and as directed. |
| 52 | S&F for aluminium anodised barrel tower bolt ISI marked of extruded section and fixed, length of bolt 200mm, complete all as specified and directed by Engineer-In-Charge. |
| 53 | S&F for 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed (ISI marked), complete all as specified and as directed. |
| 54 | S&F for floor door stopper 140mm overall length of cover plate of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in bottom body of door, complete all as specified and directed by Engineer-In-Charge. |
| 55 | M&L for 75mm thick cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in sub base, finished even and fair without using extra cement, complete all as specified and directed by Engineer-In-Charge. |
| 56 | M&L for machine pressed precast concrete interlocking paver block of any size and shape (Red and & Yellow coulour only) confirming to IS 15658-2006 of 60mm thickness M-35 grade with grey cement and no pigment including 25mm thick sand cushioning, complete all as specified and directed by Engineer-In-Charge. |
| 57 | M&L for plain cement concrete 1:3:6 type C-0 (using 12.5 mm graded crushed stone aggregate) as in filling of pressed steel frame, complete all as specified and directed |
| 58 | S&F for sinks made of stainless steel 0.80mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm fixing in repairs, complete all as specified and as directed by Engineer-In-Charge. |
| 59 | S&F in repair for vitreous china wash basin, white, flat back, size 305x310x135mm excludings taps, waste, chain and plug and porcelain stopper including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32mm dia, waste coupling of PTMT (half or full threaded) and pedestal, complete all as specified and as directed. |
| 60 | S&F in repair for basin mixer (Swan Neck) for mixing hot and cold water 2 in 1 brass chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fixed 15mm bore fixed, complete all as specified and directed. |
| 61 | S&F in repair for wall mixer (Telephonic) as in sink mixer 2 in 1, brass chromium plated screwed down high pressure with or without lathered hot or cold with long screwed shanks and fly nuts screwed for iron pipe 15mm bore, complete all as specified and directed. |
| 62 | S&F in repair for sink mixer (Non-Telephonic) 2 in 1, brass chromium plated screwed down high pressure with or without lathered hot or cold with long screwed shanks and fly nuts screwed for iron pipe 15mm bore, complete all as specified and directed. |
| 63 | S&F in repair for vitreous China squatting pattern Orissa pattern WC size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) but including lime concrete bedding, complete all as specified and as directed. |
| 64 | S&F in repair for 600x450mm bevelled edge mirror of selected quality glass mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup waste washer, complete all as specified and directed by Engineer-In-Charge. |
| 65 | S&F in repair for PVC valveless symphonic action type flushing cistern, low level, white with inlet ball valve, float and handle including brackets 10 ltr capacity, complete all as specified and directed by Engineer-In-Charge. |
| 66 | S&F in repair for angle valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore pipe, complete all as specified and as directed. |
| 67 | S&F in repair for PVC connection 15mm bore size with PTMT nuts of length 45cm length, complete all as specified and directed by Engineer-In-Charge. |
| 68 | S&F in repair for 100 mm PVC (SWR) floor/Nahani trap, plain with grating including jointing with solvent cement, complete all as specified and as directed. |
| 69 | S&F in repair for stainlees steel grating, chromium plated, size 125mm, with or without hole heavy duty, complete all as specified and as directed. |
| 70 | S&F in repair for 15mm bore CP bib tap (long body), fancy type chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and, complete all as specified and as directed. |
| 71 | S&F in repair for chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union, complete all as specified and as directed. |
| 72 | S&F for stainless steel soap dish, chromium plated, any type, fixed to plugs with screws, complete all as specified and as directed. |
| 73 | S&F in repair for stainless steel towel rail chromium plated 20mm dia 'D' type 60 cm long between flanges, ISI marked, complete all as specified and as directed. |
| 74 | S&F in repair for 15mm bore angle valve brass chromium plated screwed down, high pressure with crutch or butterfly handle concealed type with long shank cup, complete all as specified and as directed. |
| 75 | S&F in repair brass health faucet (ABS body) suitable for 15mm bore pipe with 1.25 metre long flexible tube and (ABS) wall hook including making connections and fixed in position, complete all as specified and as directed. |
| 76 | S&F in repair for rotational moulded polyethylene water storage tanks of 1000 litres capacity, (cylindrical vertical tanks with closed top) (White in colour and three layered) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc. including float valve 20/25mm, complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 77 | S&F in repair for rotational moulded polyethylene water storage tanks of 1000 litres capacity, (cylindrical vertical tanks with closed top) (White in colour and three layered) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc. including float valve 20/25mm, complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysJul 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender