|
| 1 | Excavation in Soil (any type) using Hydraulic Excavator CK 90 with hydraulic excavator of 0.9 cum bucket capacity including cutting, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, including all lifts and combined lead upto 30m. |
| 2 | Cement concrete 1:5:10 with 40 mm stone ballast using concrete mixing volumetric type |
| 3 | Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering)PCC |
| 4 | Centering and shuttering for sides and soffits of beam, beams, launching girders, bressumers, lintels. |
| 5 | Centring and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc.Slabs |
| 6 | First class burnt brick work laid in cement sand mortar 1:6 in foundation and plinth. |
| 7 | First class burnt brick work laid in cement sand mortar 1:5 in first storey upto 4 metres above plinth level. |
| 8 | 115 mm thick brick wall with every fourth course laid in 1:4 cement mortar in superstructure |
| 9 | Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth. |
| 10 | Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in superstructure. |
| 11 | 12.50 mm Cement Plaster 1:5 on walls |
| 12 | 12.50 mm Cement Plaster 1:4 on walls |
| 13 | Providing and laying 60 mm thick factory made cement concrete interlocking Paving blocks of M- 35 grade manufactured by block making machine equipped with steel mould clamped to a strong vibratory table with hydraulic pressure for compaction of concrete as per IRC SP 63 -2014 and of approved size and design / shape laid in Ordinary Grey Colour and pattern over and including 40 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer-in- Charge. |
| 14 | Supplying and fixing rolling shutters, of approved make, made of 80mmx1.25mm, M.S. Laths, interlocked together through their entire length and jointed together, at the end, by end locks, mounted on specially designed pipe shaft, with brackets, side guides, 27.5cm long wire spring grade No. 2 and arrangement for inside and outside locking with push and pull operation complete, including top cover 0.80mm thick (payment is to be made for the exact size of opening where rolling shutter is to be fixed) |
| 15 | Providing and fixing 14 gauge MS sheet garage doors with 40mmx40mmx6mm angle iron frame with diagonal braces 3.15mm gusset plates including locking arrangement with handles etc.complete in respects |
| 16 | Toilet Door |
| 17 | Providing and fixing M.S. angle iron 40x40x6mm chowkhat including iron hold fasts butt hinges fixed in position, finished with red lead non setting primer complete in all respect.Single rebate (40 x40 x 6 mm) @ 3.50 kg/mt |
| 18 | Providing & Fixing of 10 gauge welded mesh of 25mm x 25mm size fixed on steel glazing with MS flat 20mm x 6mm beading complete in all respect including painting two coats with Synthetic Enamel Paint and Priming Coat |
| 19 | Providing fixing, welding 45mm x 6mm @ 2.08 kg /mt Flat section on windows to support weldmesh in grid pattern of 600 x 600 mm . Complete job |
| 20 | Cold twisted detormed (Ribbed/ Tor steel) Bars (Fe 500 grade as per IS 1786-2008) , for R.C.C works, where not including in the complete rate of RCC including bending and binding placing in position complete |
| 21 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5- 7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.60 mm (+ 0.05 %) thick |
| 22 | Earth filling with good quality earth obtained from outside the plinth including compensation of earth, loading, unloading, carriage from outside the premises to site of work, spreading, laying watering compacting with rammer complete as per specifications. (filling considered above road level as per site conditions)(Ramp area ) |
| 23 | Earth filling under floors with surplus ordinary soil or soil containing gravel or kankar up to 40% excavated from foundation and taken only from outside the building plinth in 15 cm layers including ramming, watering and consolidating lead up to 30 metres.Area of 40% earth excavation |
| 24 | Base coarse of floor consisting of 100 mm thick cement concrete 1:8:16 with stone aggreate and 100 mm sand filling.(using mechanical mixer for mixing of material) |
| 25 | white wash ( 3 coats) |
| 26 | Outer Area Preparation of plastered surfaces for distempering including surface, applying filling with approved quality filler consisting of plaster of paris and chalk mitti including finishing the surface to the required finishcomplete |
| 27 | Finishing walls with water suitable exterior cement based paints as snowcem, Robbicem etc. on new work two coats to give an even shade. |
| 28 | Applying priming coat with metal primer on new steel or iron work including preparation of surface.(door , windows, weldmesh , angle frames, trusses , purlins, rolling shutters etc.) |
| 29 | Painting two or more coats excluding priming coat with ready mixed paint for metallic surfaces in all shades on steel or iron work |
| 30 | Structural steel work in angles, tees, flats, riveted, including cutting, fixing all gusset plates, bolts, nuts, rivets etc. with hoisting and erecting in position.For roof truss, well curbs, plate girders etc.of any span for building for bridges upto 15M span |
| 31 | Public health works |
| 32 | Providing, lowering, cutting & jointing salt Glazed Stone ware Pipes and Specials ISI marked as per IS 651-2007 class Sp-1 into Trenches for all depths and Laying out the same to correct alignment, Gradients, levels etc., cutting of concrete beds and joints holes, supporting the pipes and specials, in correct position in a suitable rigid manner while the same are being jointed and until the surrounding benching, haunching and envelopes are completed. including jointing of pipes and specials in trenches, using cement sand mortar 1:1 and best spun jute yarn,as per IS :1887 finishing and trowelling of each joint at an angle of 45degree with the longitudinal axes of pipe, watering, keeping the joint covered and wetted till the same are cured, testing the sewerage line for leakage and making all leakages and defects good as laid in the contract specification, hipping and finishing the cut surface to uniform finish to the entire satisfaction of engineer-in-charge Including all cartage etc.complete in all respect.100 mm internal diameter of sewer. |
| 33 | Excavation of trenches in a Streets, Lanes or in Open Area for Storm Sewers and Manholes to Full Depths as Shown in Drawings, Including Shoring, Timbering of polling Board Frame System Type, dressing to correct sections and dimensions according to template and dewatering, provision for diversion for traffic, protection of exiting services i.e. telephone cables , electric lines, water supply lines and Gas lines etc,Providing and fixing night signals, profiles, Pegs, Sight rails, boning rods, crossing over trenches for access to the houses, watching, fencing etc.,Providing and fixing and maintenance of caution boards, refilling trenches, watering of refill in 15 cm layers, ramming and restoration of surface to original conditions and removal of Surplus Spoil from the Site of Works, for all Works other than connections to Ventilating Shafts upto a Lead of one Kilometre. for depth not exceeding 3 mtr. BGL In all classes is soil except rocky.100 mm SWP (2x0.60x1) |
| 34 | Cement concrete 1:6:12 with brick ballast 40mm gauge 2 X 0.085 |
| 35 | Construction of brick masonry inspection chambers size as given below upto 0.60 metre average depth in 1:5 cement sand mortar, C.C.1:4:8 ( 150mm thick) in foundation, cement concrete 1:2:4 benching 12.50mm thick cement plaster 1:2 with a floating coat of 1mm thick of neat cement, R.C.C. 1:2:4 slabs 100mm thick cement concrete topping 50mm thick with 455mm x 455mm, 455mm x 610mm inside R.C.C. inspection chamber cover and frame (Weight as per I.S.I specifications) painted with 3 coats of black bitumastic paint conforming to I.S.I complete as per standard design.-Size 450mm x 450mm inside with RCC 455mm x 455mm cover and frame light duty double seal |
| 36 | Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with Grating 150mm x 150mm, cover and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm and chamber including cost of all bricks work in cement morter 1:5 cement concrete 1:2:4 in coping around cover and frame etc. as per standard design minimum depth of water should be 150 mm with a minimum seal 50mm.100mm internal Dia mtr SW gully trap with HCI grating and cast iron covered waieighing approximately 7.26 KG and frame clear opening 300X300mm and our of site size 330mmX330mm |
| 37 | Construction of SEPTIC TANK mearuing 1.25 x 1.0 x 1.30 mt depth including RCC in bed , RCC roof slab, Providing anf fixing RCC mnhole cover 450 mm 450 mm & frame light duty , cement plaster inside , vent pipe with cowl etc.Complete in all respect. |
| 38 | Construction of SOAK PIT mearuing 2.85 MT ( internal dia), 3.00 mt depth, excavation, brick walls, boulders , filling, percolation, boring (3.00) mt etc.owl etc.Complete in all respect. (As per standard drawing and design) |
| 39 | Providing, laying , jointing , fixing and testing GI pipes ( as per IS 1239) B- CLASS premium such as including cost of specials ( such as tees, elbows , bends , socktes elbows etc) painting with anti corrosive bitumatic paint,cutting , threading and testing in trenches in the ground complete including excavation with 1 mt depth .Complete in all respect.20 mm i/d |
| 40 | Making connection with existing GI branch main upto 40 mm size pipe including cutting of existing pipe line, threading of pipe line from bioth ends and fixing of GI tee etc. in the pipe line ( including cost of GI TEE). Complete in all respect |
| 41 | Providing, laying , jointing , fixing and testing GI pipes ( as per IS 1239) B- CLASS premium such as (Jindal hisar) including cost of specials ( such as tees, elbows , bends , cocktes elbows etc) painting with anti corrosive bitumatic paint,testing ,cutting , threading inside building complete15 mm i/d |
| 42 | Providing & Fixing and jointing GI union couplings of approved maked with the approval of EIC as per IS 1889 in GI pipe lines complete in all respects.20 mm i/d |
| 43 | 15 mm i/d |
| 44 | Providing, fixing and jointing Brass Ball valves screwed with SS/BRASS ball & spindle & Teflon seats, on G.I. Pipe lines including all carriages complete.20 mm i/d |
| 45 | 15 mm i/d |
| 46 | Cutting holes up to 23 cm square through B.B. in cement walls or stone masonary walls in cement for pipes and making goods the same and finishing accoridng to existing finish where required.11.43 cm thickness of walls |
| 47 | 22.86 cm thick ness of walls |
| 48 | Cutting chase in brick walls in cement or in floor for embedding G.I. or C.I pipes lines and making good the same to its original condition.Size 75 mm x 75 mm |
| 49 | Size 150 mm x 150 mm |
| 50 | Cutting holes upto 23 cm square for pipes in flooring and roofs of bricks , tiles with lime concrete or cement concrete and making good the same and finishing according to existing finish where required.115mm thick ness of floor or roof. |
| 51 | Providing and Fixing Iron Holder Bats 20mm/15mm o/d Pipe line |
| 52 | Providing and fixing in position Chinaware indian orisa water closet 350-400 mm of approved make ( to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern inlcuding cost of PVC long bend 32 mm dia complete in all respect and to the entire satisfaction of engineer in Charge.( baby friendly water closet) |
| 53 | Providing and fixing in position vitreouschinaware white lavatory suites of approvedmake (to the approval of Engineer-in-charge) consisting of C.P. brass waste 32mm dia with one C.P. brass pillar tap including Rack Bolt Screw Pair 115mm long complete in all respect. |
| 54 | Providing and fixing in position stainless steel sinks of approved make (to the approval of Engineer-in-charge) 1mm thick,grade-304 (18/8) with waste coupling complete in all respect.Rectangular Sink with Deluxe Border Single Bowl Overall Size 555 mm x 475mm x 200 mm |
| 55 | Providing and fixing P.V.C Waste Pipe Collapsiable 32mm complete in all respect |
| 56 | Providing & placing in position on terrace (at all floor levels) HDPE water storage tanks of approved make (to the approval of Engineer -in-charge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fittings and base support for tank - Double Layer Tanks |
| 57 | Providing and fixing in position automatic brass Ball Cock in tanks. Brass Ball Cock with rod and Plastic Ball.20mm i/d |
| 58 | Providing and fixing in position G.I. Tank Nipple of approved make (to the approval of Engineer-in-charge) in PVC Water storage tanks complete in all respect. G.I. tank nipple 20 mm i/d |
| 59 | Providing & Fixing in position C.P. Brass flange Dome of approved make (to the approval of Engineer-in-charge ) under various fixtures complete in all respect. |
| 60 | Providing & Fixing in postion CP brass extension piece 25mm long to 50mm long of approved make (to the approval of engineer in charge) with various fixture complete in all respect |
| 61 | Providing & Fixing in postion C.I.bib cock as per IS:210 with stainless steel spindle of approved make (to the approval of Engineer-incharge) complete in all respect.15mm i/d |
| 62 | Providing & Fixing in postion stop cock /Angle valve of approved make (as approved by the Engineer-in-charge). Complete in all repectCP brass 15mm Stop cock male & female end |
| 63 | Providing & fixing in position PVC Flexible tube connection of approved make (as approved by the Engineer-in-charge). Complete in all repect size PVC tube connection of size 15 mm x375 mm with PTMT nut |
| 64 | Providing and fixing in position SWR UPVC soil waste vent or antisyphonage pipes as per IS -13592 of approved make (to the approval of Engineer-in-charge)including cutting, jointing, wastage, but excluding cost of lead jointing. Type B 110 mm o/d SWR UPVC pipe line laid complete |
| 65 | 90 mm o/d SWR UPVC pipe line laid complete |
| 66 | Providing and fixing in position SWR UPVC specials for soil waste vent or anti syphonage pipes as per as per IS - 14735 of approved make (to the approval of Engineer-in-charge) including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining.For 110 mm o/d pipes Single Tee |
| 67 | Elbow 90 Degree (All side socketed) |
| 68 | Coupler |
| 69 | Vent Cowls |
| 70 | P Trap/Floor Trap 110mm x 110mm |
| 71 | Nahani trap without jali 110mmx90mm |
| 72 | For 90 mm o/d pipes Single Tee |
| 73 | Coupler |
| 74 | Elbow 90 degree (all side socket) |
| 75 | Providing and fixing in position SS Grating with frame of approved make (to the approval of engineer in charge) complete in all respects |
| 76 | Electrical works |
| 77 | Electrical wiring and Connections with switches and sockets |
| 78 | Exhaust fans.Complete job including wiring,regulators, and fixing arrangments etc |
| 79 | Ceiling fans.Complete job including wiring,regulators, and fixing arrangments etc |
| 80 | Electrical LED Lamps of 12 watt . Complete job inlcuding wiring , fixing, switches, labour charges etc. |
| 81 | Folding MS Table measuring 1.80 x 1.20 x 0.80 made out of 40 x 40 ms pipe section duly fixed with good quality wooden panels as per standard design. Complete job including paint polish, footrest, table top made out of wood members |
| 82 | Bailed Machine. Complete job including carrige, fixing and installation, electrical power plug, connections as per manufacturer requirements. Complete job (specification for Bailing Machine the bailing capacity should be at least 25 tonne, bale size 700 x 500, bale weight 40 to 60 kg having hydrolic system gear pump/ double piston pump/vane pump system with hydrolic vertical clamping force to operarte confermng to latest reavent BIS specification/ISO certification). Complete in all respect. |
| 83 | Twin Shaft Shredder Hopper Input dimenssion 500 mm x 300 mm, shredder chamber size 300 x 230 mm blade thickness 8 mm with cabon steel including fixing and instalation, electrical power plug, connection as per manufacturer requirement. Complete job (Specification for shredder machine the machineyc powered with motor heavy structure with C-Channel power 415-v AC, 5.00 BHP motor, Three phase plus nutral earthing) conferming to letest relavent BIS specification/ISO certification) Complete in all respect. |
| 84 | Dusting Machine.Complete job including fixing and installation, electrical power plug, connections as per manufacturer requirements. Complete Job Please Enable Macros to View BoQ information |
