|
| 1 | Pumping out of siltation by sand blowing pump as per specification and direction of the Engineer in Chage. Siltation clearing from intake well of H.P.L.I. Scheme. |
| 2 | Providing structural steel work in single section fixed with or without connecting plate including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as required |
| 3 | Providing structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as required. |
| 4 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 5 | Providing and fixing MS bolts including nuts and washers complete as per standard design:Upto 300mm length |
| 6 | To open out existing old rubber seal and covering plate from steel gate by cutting nut and bolts where necessary as per direction of the engineer in charge. |
| 7 | Supplying and fitting fixing at site rubber seal for steel gate and fixing them with new bolts and nuts and washer and pouching necessary tubes in rubber seal with new covering plate. The new rubber seal are to be proper shape and size, hard were staging and scaffolding where necessary as per diredtion of the Engg-in-Charge. |
| 8 | Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63mm thick with zinc coating not less than 275gm/m2 |
| 9 | Painting on G.S. sheet with synthetic enamel paint ( one or more coats ) of approved brand and manufacture of required colour to give an even shade on old work including preparation of surface as required complete as per direction of the Engineer in charge:- |
| 10 | Providing and fixing G.I. pipes medium class as per IS : 1239 with latest amendment complete with G.I. fittings including trenching and refilling, cutting and making good the walls etc. complete as per chapter 20 of CPWD specification and direction of the Engineer- in - charge. |
| 11 | Providing and fixing 10 mm thick MS sheet flap shutter gate with frame of 50x50x5mm MS angles & vertical brace 25x6mm MS flat and all necessary coat of approved steel primer complete as directed by Engineer-in-charge (Cost of MS angles, MS flat will be paid separately ) |
| 12 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering -All work upto plinth level: a) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size) |
| 13 | Centering shuttering including struttings, propping etc. and removal of form work for: |
| 14 | a) Retaining walls, return walls, walls (any thickness) including attached pilasters, but-tresses plinth and string courses fillets etc. |
| 15 | b) Columns, piers, abutments, pillaras, posts and struts |
| 16 | First class brick work in foundation and plinth including cost of all materials as required complete. In cement mortar 1:4 ( 1 cement : 4 fine sand) |
| 17 | 12 mm cement plaster of mixIn cement mortar 1 : 4 ( 1 cement : 4 fine sand ) |
| 18 | 6 mm cement plaster of mix : Cement mortar 1:4 (1 cement : 4 fine sand) |
| 19 | Neat cement Punning |
| 20 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. |
| 21 | Supplying and stacking mixed class brick bats (50% first class & un-class)including carriage loading & unloading at the site of work complete as per direction of the engineer- in-charge. |
| 22 | Dismentaling of pump for over hauiling including greasing, gland packing, necessary repairs & reinstallation of the same including trial run for 10 hrs. in two spell complete as per direction of the Engineerin- Charge. For HPLI |
| 23 | Providing & fitting fixing C.I coupling complete with nuts & bolts of approved quality. 225 mm dia |
| 24 | Providing & fitting fixing coupling rubber bush (All Size) of approved quality. For HPLI |
| 25 | Providing & fitting fixing coupling star bush (All Size) of approved quality. 225 mm dia |
| 26 | Providing & fitting fixing Shaft sleeve of approved quality. For HPLI |
| 27 | Providing & fitting fixing Shaft sleeve nut of approved quality. |
| 28 | Providing & fitting fixing C.I. gland of approved quality |
| 29 | Providing & fitting fixing Gland nut / Stag nut 100 mm long for gland of approved quality. |
| 30 | Supply & fitting fixing ball bearing of approved quality for pump required during overhauling. 6312 Ball bearing (TATA /SKF) |
| 31 | Hiring charge of welding set of single phase with operating staff and carrying upto the site of work including loading and unloading (both way) complete as per direction of Engineer-incharge. |
| 32 | Providing and fitting fixing of brass fullway valve with handle in the GI pipe line including cutting, threading etc. complete as per CPWD specification and direction of the Engineer - in -charge. |
| 33 | charges for fitting fixing of brass fullway valve with handle (issued from department free of cost) in the GI pipe line including cutting, threading etc. complete as per CPWD specification and direction of the Engineer - in - charge. |
| 34 | Providing and fitting fixing of Fully Automatic Star Delta type Motor starter ( 3 ph. 50 Hz, 415V, in Steel Sheet Enclosures with Contractors and Timer etc. complete suitable for submersible Pump L & T, BCH, ABB make as per specification and direction of the Engineer-in-charge. |
| 35 | Supplying and greasing/applying of grease in wheel bearing complete as per direction of Engineer-in-charge. |
| 36 | Supplying and fitting fixing of asbestos rope of best quality as per direciton of Engineer-in-charge. |
| 37 | Labour charge for reinstallation of all electrical equipments (dismentalled serviceable materials, if any additional/ replacement of electrical eqiupments required will be paid separtely) on the pannel board including trial run for 10 hrs in two spell complete as per direction of the Engineer-in Charge. |
| 38 | Rewinding of Harizontal Motor suitable for centrifugal pumps by complete dismantling in/c providing & rewinding with super enamelled copper conductor (as per IS : 13730 Part-3) conductor & all necessary spare parts and reassembling the same including servicing of rotor & necessary trail run as per specification and direction of the Engineer-in-Charge. |
| 39 | Providing & fitting fixing foot valve leather washer (6 mm thick) of heavy duty at site of work of approved quality. |
| 40 | Providing and fitting fixing MS Foot valve as per relevant IS specification and the direction of the Engineer-in-charge.200 mm dia Please Enable Macros to View BoQ information |
