Tender For Repair And Maintenance Of Mes Installation In Sector C, E, F Under Ge (A) No 1 In Army Area Jodhpur
Tender Value
45 Lakhs
Estimated cost
Bid Submission
07 Jul 2026
0 days left
EMD
90000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jodhpur → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair And Maintenance Of Mes Installation In Sector C, E, F Under Ge (A) No 1 In Army Area Jodhpur
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance out side MD land complete all as specified and as directed. |
| 2 | Dismantling, stone slab, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises,complete all as specified and as directed. |
| 3 | Taking down chowkhats or frame with shutters (without taking of shutters from the frames) area not exc 1.5 Sqm each, complete all as specified and as directed. |
| 4 | Taking down chowkhats or frame with shutters (without taking of shutters from the frames) area exc 1.5 Sqm but not exceeding 4 Sqm each,complete all as specified and as directed. |
| 5 | Taking down Shutters of any description exceeding 1.00 Sq.m but not exceeding 2.00 Sq.m each complete all as directed. |
| 6 | Taking down Shutters of any description and refixing the shutters in the same opening of any description exceeding 1.00 Sq.m and not exceeding 2.00 Sq.m each after easing and adjusting complete all as specified and as directed. |
| 7 | Taking down steel windows/ ventilator with frame of any description and any size complete & remove from site complete all as specified and as directed. |
| 8 | Demoltion of cement cocrete padding of water proofing treatment from roof pading taking down bituminous polythene sheets plaster etc , cleaning of concete surfaces by wire brushres scrubbing down water and removing the dust debris etc. to a distance 50 mtre but n.exc 250 mtr from the site, complete all as specified and directed. |
| 9 | M&L for Plain cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as over roof for making good depression/ undulation to make the existing as filling in depression of roof slab,complete all as specified and as directed. |
| 10 | M&L for carrying out water proffing treatment for roofs in the following stages:- (i) Rendering 10mm thick in cement mortar (1:4), mixed with integral water proofing liquid allas per manufacturer's insturctions over concrete surfaces finished even and smooth with out using extra cement. (ii) Material and labour for UV stable single component fibre reinforced elastomeric liquid applied water proofing membrane having solid content of 55% formulated with PU hybrid polymers and reinforcing acrylic fibers and having sun reflectivity Index (SRI) of 106. The application of the material should be done in three coat 6 hr gap after each coat) on the substrate, applying first self priming coat at ratio of damp proof ultra and water 3:1 then 2 undiluted coat of damp proof ultra obtaining coverage @1 ltr/ 10 sqft in two coats (10-12) hrs gap between each coat. The vital physical and chemical parameters shall be as under. Min elongational break of 350% crack bridging ability of 2.5mm @650 microns thickness resists positive hydrostatic pressure of up to 10 bars. The material shall be applied with bursh or roller, Also proper surface preparation along with covingat corners is must etc, complete all specified and directed. Note : 1The work shall be executed by the authorized applicator of the manufacturere only.2 The authorized applicator of manufacturere shall be approved by GE. 3. The color of final finish shall be decided by the GE. 4. WPC rate is included in quated rate. |
| 11 | Supply and laying of coarse aggregate of nominal size 40mm (aggregate shall be measured net, in compact stacks, prepared on level ground. Where directed, the materials shall be measured in 'pharmas' (bottomless gauge boxes). While no special compaction is necessary by ramming, jerking or hammering. No attempt at loose staking shall be permitted) etc, complete all as specified and directed. |
| 12 | Taking down existing steel rolling shutter of any size, complete all as directed. |
| 13 | S&F of 1mm thick lath steel rolling shutterts, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, complete with gear operated type with bevel gear box and crank handle etc, complete all as specified and directed. |
| 14 | S&F ball bearing for rolling shutters etc, complete all as specified and directed. |
| 15 | S&F safety lever locks mild steel with 4 levers for rolling shutters etc, complete all as specified and directed. |
| 16 | S&F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tubes suppyling & fixing in opening as per specification & drawing complete all as spcefied and directed. |
| 17 | S&F of factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as spcefied and directed. |
| 18 | S&F of framed work as in door or gates of angle or other section with gusset plates, rails, braces, etc, complete drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing etc and similar work fixed with angle cleates, confirming to Fe 410 Grade E - 250 Quality A, complete all as specified and as directed. |
| 19 | S&F 35 mm thick second class hard wood factory made plain, framed, panelled shutters, with lock rail and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and Style as per IS:1003 (Part-1), kiln seasoned and chemically pressure treated complete all as specified and as directed. |
| 20 | S&F in repairs galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18 mm complete all as specified and directed. |
| 21 | S&F 100 mm long medium weight, cold rolled Stainless steel Butt hinges complete all as specified and directed. |
| 22 | S&F 100 mm long medium weight, cold rolled mild steel (ISI Marked) Butt hinges complete all as specified and directed. |
| 23 | S&F in repairs single action spring hinges, mild steel with steel wire spring, stove enamelled, black , 100mm size spring hinge, complete all as specified and directed. |
| 24 | S&F 300 mm long aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 25 | S&F 100 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed. |
| 26 | S&F 150 mm long Aluminium handles, fabricated type, anodised complete all as specified and directed. |
| 27 | S&F in repairs of aluminium (die-cast)body door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as specified and as directed. |
| 28 | Taking down carefully cement conc /spalled out concrete from RCC roof projections, cilinigs ,sunsheds, beams, etc upto cover depth by chipping out lightly including necessary scafolding etc ,complete all as specified and as directed. |
| 29 | M&L for Cleaning the existing reinf of slabs , chajjas etc & applying a coat of SIKA RUSTOFF 11 to remove the loose rust particles etc & throughly cleaning the surface,complete all as specified and as directed. |
| 30 | M&L for Applying a coat of bond coat made with cement slurry (1 part cement to 1.5 -2 parts water) mixed with admixture LATEX POWER mixed @5 Kg per 50 kg of cement & applying to the conc surfaces @ 200 gm/sqm to obtain tack,complete all as specified and as directed. |
| 31 | M&L for 15 -20 mm thick rendering in CM 1:1:2 using1 part of cement 1 part 2-3 mm screenings of stone agg & 2 parts coarse sand over the bond coat applied surfaces with cement mixed with SIKA PLASTOCRETE SUPER admixture @ 100 gm /50kg of cement & finishing the surface even & rough to receive final rendering coat,complete all as specified and as directed. |
| 32 | M&L for 5 mm thick rendering in CM 1:3 & finishing the surface even & smooth w/o using extra cement,complete all as specified and as directed. |
| 33 | Hacking out old broken glass (any thickness, size, quality or description) from metal frame incld punching or drilling out old glazing pins/ spring clips and provding and fixing new ones, complete all as specified and as directed. |
| 34 | S&F Sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq.m in each pane complete all as specified and directed. |
| 35 | S&F for powder coated (minimum thinkness of powder coating is 50 micron) anodized Aluminium Frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. |
| 36 | S&F for powder coated anodized aluminium door shutters, aluminium section weighing 0.55Kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door hinges, anodised aluminium snap beading screws etc. complete all as specified and directed. |
| 37 | S&F for powder coated anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluninium fittings such as peg stays 150mm long (1 No) hinges type B-21 100 mm long (2 No) suitable handle (1 No) in each shutter complete all as specified and directed. |
| 38 | S&F Sheet glass 4.80mm thick, ordinary quality and glazing with oil putty in squares exceeding 0.5 Sq.m in each pane complete all as specified and directed. |
| 39 | S&F for 4 mm thick figurred, pin headed glass ordinary quality & glazing with oil putty in square n exc 0.50sqm in each pane, complete all as specified and as directed. |
| 40 | S&F in replacement of Double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminum alloy sheet foundation box, main body with stainless steel cover governing pivot made of brass, other parts made of mild steel heavy duty & fixed complete all as specified and as directed. |
| 41 | S&F in replacement mortice latch with two loovers (Vertical type) mild steel body 100mm long and fixed complete all as specified and as directed. |
| 42 | M&L for 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in sub base of flooring, incld. finishing the surface even & rough to receive tiling etc., complete all as specified and as directed. |
| 43 | M&L 75 mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base as in floor etc., complete all as specified and as directed. |
| 44 | S&F 28-30 mm thick precast chequered tiles any shape rubberised finish Lacquer coated with top 4-5 mm with anti abrasive material all as per sample laid over cement sand screed (measured seprately) jointing & pointing in neat cement mixed with pigment over 15 mm screed bed in cm 1:4 etc., complete all as specified and as directed. |
| 45 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand etc., complete all as specified and as directed. |
| 46 | S&F machine made precast cement concrete curb stone blocks using Cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) set in CM 1:6 etc., complete all as specified and as directed. |
| 47 | M&L 50 mm thick PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) laid in alternative bays as in plinth protection including finishing the surface even & fair & filling the joints with mastic filling i.e one part of bitumen 85/25 and 3 parts of sand by weight in 2 mtr interval, complete all as specified and directed. |
| 48 | M&L PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundation , filling, sub base and mass concerete complete all as specified and as directed. |
| 49 | M&L for glazed colour ceramic tiles (premium quality) of size 300X450X6-7 mm, as in vertical surface such as i.e. dado/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over & including M&L 10mm thick backing coat in CM (1:4), (including Highlighter pattern), complete all as specified and directed. |
| 50 | M&L for joint free non skid ceramic coloured tiles (premium quality) of size 7 to 8 mm thick (square/rectangular) area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm, as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including M&L 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed. |
| 51 | All as per item No. 50.00 here-in-above, but size of tile exceeding 0.11 Sqm but n.exc. 0.18 sqm . |
| 52 | All as per item No. 50.00 here-in-above, but as in skirting over & including M&L 10 mm thick rendering in CM 1:4 complete all as directed. |
| 53 | M&L for light shade vitrified ceramic tiles, 10 mm thick (square/ rectagular) polished, area of each tiles not exceeding 0.72 sqm, (size & shape, shade and pattern as approved by GE), as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles, over & including M&L 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed. |
| 54 | All as per item No. 53.00 here-in-above, but as in skirting over & including M&L 10 mm thick rendering in CM 1:4 complete all as directed. |
| 55 | M&L Machine cut kota stone slab 20 to 25mm thick as in floor laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including M&L 15mm thick screed bed in CM 1:6, complete all as specified and as directed. |
| 56 | All as per item No. 55.00 here-in-above, but as in skirting over & including M&L 10 mm thick rendering in CM 1:4 complete all as directed. |
| 57 | Taking down cement plaster in any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified and as directed. |
| 58 | M&L for 15 mm thick rendering in CM 1:4 on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing finished surface fair and even without using extra cement, complete all as specified and as directed. |
| 59 | M&L for 15 mm thick rendering in CM 1:6 on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing finished surface even and smooth without using extra cement, complete all as specified and as directed. |
| 60 | M&L for 10 mm thick Rendering in CM 1:4 on fair faces of brick work or concrete surfaces as in ceilings/chajja/facia & finished even & smooth w/o using extra cement, complete all as specified and as directed. |
| 61 | M&L for Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash on ceiling surfaces complete all as specified and as directed. |
| 62 | All as per item No. 61.00 here-in-above, but as on wall surfaces |
| 63 | Complete removal of existing treatment of any description on walls and applying with 2 mm thick wall care putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper over & including M&L single coat of primer on walls complete all as specified and as directed. |
| 64 | M&L for preparation of new plastered wall surfaces and applying two coats of oil bound distemper white or tinted over & including applied of 1.5 to 2 mm thick wall care putty over & including a coat of alkali primer etc,complete all as specified and as directed. |
| 65 | M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over & including a coat of primer complete all as specified and as directed. |
| 66 | Taking up or down 15mm bore steel tubing medium grade and connections, as in walls, ceiling, floor etc including cleaning for re-fixing or credit to the work complete all as specified and as directed. |
| 67 | All as per item No. 66.00 here-in-above, but 20 mm bore |
| 68 | Supplying and laying of CPVC pipes, 20 mm ouetr dia of pipe, SDR 11 & Plain CPVC SDR 11 including all brass fittings, laid in trenches or ceiling or fixed to wall complete all as specified and as directed. |
| 69 | All as per item No. 68.00 here-in-above, but 25 mm outer dia |
| 70 | S&F in replacement vitreous ware wash down water closet [Pedestal Pattern], white [ETWC] including plastic water closet seat back soft closed pattern with flat bottom and cover & jet and mild steel chromium plated or aluminium hinging device and 'P' or 'S' trap connecting to drain pipe and flushing pipe etc., complete all as specified and directed. |
| 71 | S&F in replacement white vitreous china squatting pan \\"Orissa pattern\\" of size 580 mm X 440 mm with integral foot rests and PVC 'P' or 'S' trap, including M&L brackets, flush HDPE pipe of 32 mm dia and PVC connection 15mm size, 450 mm long with PTMT nuts , including provision of cement concrete bedding 1:5:10 type E-2 complete all as specified and as directed. |
| 72 | S&F in repairs PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed. |
| 73 | S&F in replacement fancy type 600mmx450mm plain edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed. |
| 74 | S&F in replacement Wash basins, Vitreous China white, flat back, size 630x450mm excluding tap, waste chain and plugs but including brackets(flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand and including waste pipe 32mm bore, PVC connection 450mm long etc, complete all as specified and as directed. |
| 75 | S&F in replacement vitreous china bowl urinal flat back, size of 465 x 355 x265 mm white (minimum ),with grating and union for discharge pipe including waste pipe ) etc, complete all as specified and as directed. |
| 76 | S&F in replacement rotational moulded polyethylene water storage tank ISI Marked (cylindrical vertical with closed top) white, hoisted and fixed in position all as directed of capacity 500 ltrs a Including 20mm bore brass ball valve high pressure with polythene float complete including taking down existing damage water tank all as directed. |
| 77 | All as per item No. 76.00 here-in-above, but 1000 ltrs tank capacity |
| 78 | S&F in replacement CP mild steel grating 100mm dia complete all as specified and as directed. |
| 79 | Dismantling of cast iron of CI / PVC soil, waste & vent pipe jointed in cement mortor of size 110/100mm bore, incld. All fittings, complete all as specified and as directed. |
| 80 | All as per item No. 79.00 here-in-above, but 75mm bore pipe. |
| 81 | Supply & laying 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in wall/ceiling/floor of suitable size complete all as specified and as directed . |
| 82 | All as per item No. 81.00 here-in-above, but 110mm bore pipe. |
| 83 | S&F in replacement decorative type curtain rod stainless steel finish of pipe 22 to 25 mm dia with best quality knob metal with double fitting type including stainless steel brackets fixed to walls complete with two nos decorative stainless steel knobs at each end (as approved by GE), complete all as specified and as directed. |
| 84 | Dismantling of plain or corrugated asbestos sheeting, any gauge, thickness including nainital or similar pattern in roof coverings complete all as specified and as directed . |
| 85 | M&L Prepainted Galvalume Aluminium Zinc Coating GI based corrugated Steel Sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws, complete all as specified and directed. |
| 86 | M&L for preparing new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over & including M&L single coat of pink primer complete all as specified and as directed. |
| 87 | M&L preparation of new or previously untreated steel surface of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over & including M&L single coat of red- oxide, zinc chrome primer complete all as specified and as directed. |
| 88 | Dismantling of stone / boulder masonry walling, built in cement mortar including all quoins, arches, pillars etc and removal unserviceable materials, debris, rubbish to out side MD land complete all as specified and directed. |
| 89 | M&L for squared rubble walling, Jodhpur type, regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6, complete all as specified and directed. |
| 90 | All as per item No. 89.00 here-in-above, but except stoneNote:- Stone retrived from item no 88.00 of BOQ here-in -before. |
| 91 | Extra over stone walling for hammer dressing to face stone & dressing of face beds & joints as specified of squared rubble walling Jodhpur type brought upto courses with maximum depression of face from straight edge held against the dressed surface n exc 20mm and dressing face beds and joints, complete all as specified and directed. |
| 92 | M&L precast cement concrete block masonry using PCC 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) solid blocks, 10 cm in width and setting in cement mortar 1:4, straight or curved on plan exceeding 6 m mean radius, including demolition of existing block masonary, complete all as specified and directed. |
| 93 | Racking out joints/ pointing to squared rubble or polygonal rubble un-coursed or brought up to courses masonry built in cement mortar or cement lime mortar, coursed or un-coursed in walls not less than 12mm deep, washing the joints, removing rubbish off the premises and keeping the surface to pointed or plastered wet for two days prior to re-pointing or plastering complete all as specified & directed. |
| 94 | M&L keyed pointing in cement mortar (1:3) to squared rubble masonry regular coursed or un coursed complete all as specified & directed. |
| 95 | M&L for preparation of old painted surfaces of walls or roofs by brooming down or steel wire brushing, scraping down smoke spot, moulds, moss and efflorescent salt and greasy spots and applying two coats of cement base paint, complete all as specified and directed |
| 96 | M&L for precast cement concrete Type B-0 1:2:4 (by using 12.5mm graded crushed stone aggregate) as in louvres and jallies, cement grill any type model of Zafri , 35mm thick (measured solid), set in cement mortar 1:4 fixed with PCC post, incld. all mouldings & MS wire etc, complete all as specified and directed. |
| 97 | Supply & laying of precast cement concrete1:3:6, type C-0 (by using 12.5mm graded crushed stone aggregate) as in pillars (size 100 x 100 mm and 750mm height) to provide support of RCC jallies, jointed with neat cement slurry, in CM 1:6, and including MS wire & demolition of existing jallies and removed from MOD land, complete all as specified and as directed. |
| 98 | Dismantling of RCC/MS Angle fencing post or struts of any description/section including taking out embeded ,barbed wire in concrete and making good disturbed, complete all as specified and as directed. |
| 99 | Dismantling of fencing wire mesh, any type and any size complete all as specified and as directed. |
| 100 | Excavating in post holes (of similar holes) each n. Exc. 0.50 cum getting out in any type of soil, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering and removing surplus soil to a distance n. Exc. 50m and making good surface complete all as specified and directed. |
| 101 | S&F mild steel sections like angle, flat etc in post and struts in fencing including cutting top to shape as directed,drilling holes,notching for wire etc;flat iron fillets (for securing wire mesh etc including all necessary drilling,bolting or riviting etc confirming to Fe-290Gde E-165 complete all as specified and as directed. |
| 102 | S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and scrfewed the other, each screwed end to be fitted with washeres and one haxagonal or square nut not exceeding 5cm long with dai of neck 5 to 11 mm complete all as specified and directed. |
| 103 | Supply only chain link MS galvanised fencing of any description, complete all as specified and as directed. Note:- BOO will consitute by GE to determinate the weight of chainlink. |
| 104 | Fixing only Chain link fencing including line wires,any mesh, size and type to any standards,rails straining bolts, etc. including provision of binding wire complete all as specified and as directed. |
| 105 | Supply only Mild steel round or square bars 10mm dia.,in available length Fe-290 (Gde-165) for fixing of chain link fencing complete all as specified and as directed. |
| 106 | S&F galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins, etc complete all as specified and as directed.Note : - Each line wire to be measured. |
| 107 | S&F in repair Fibre glass reinforced translucent 2 mm thick corrugated sheeting with two corrugation side lap fixed with coach screw and washer in roof ,wall etc complete all as specified and as directed. |
| 108 | Complete removal of existing treatment of any description on walls and applying two coats of exterior acrylic emulsion (one or more tints) over & including M&L single coat of primer on walls complete all as specified and as directed. |
| 109 | M&L for 18 to 20 mm thick (telephone black shade) granite stone, as in WHB counter top, machine cut, (table rubbed and polished) best quality as per sample, over & including 15 mm thick screeding in CM1:4 including rounding & double mouldlng with jointless finish of the edges, including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.providing suitable dia hole in the slab for the gas pipe, complete all as specified and as directed. |
| 110 | M&L for TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns hooking ends cutting bending and binding with mild steel wire (annealed) not less than 0.90mm dia or securing with clips, complete all as specified and as directed. |
| 111 | S&F mild steel TMT bar 8 mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed. |
| 112 | M&L for formwork to Edges of concrete flats, treads, breaks in floors.concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC band in walls, sloping and similar work for fair finished surfaces. Rough finished surfaces of concrete flat, complete all as specified and as directed. |
| 113 | M&L RCC nominal mix type B-1 (1:2:4) (using 20 mm graded crushed stone aggregate) as in slab supported on wall, beam and column in floors, roofs, landing, balconies, canopies, ramp roof slab, chajja and in shelve etc complete all as specified and directed. |
| 114 | M&L for sand filling under floors or in foundations including watering and consolidation, spreading and levelling in layers n.exc. 25cm thick and well ramming including watering as rerquired etc, complete all as specified and directed. |
| 115 | M&L for 50mm thick Sand stone slabs in sunshades, chajjas, shelves, cills, landings, drain cover stones, templates, etc, n exc. 2m in length, machine cut on all faces and along exposed edges, self faced on both side and set and pointed in lime mortar 1:3 or cement mortar 1:4, complete all as specified and as directed |
| 116 | S&F in replacement identification sign/cautionary mandatory and information sign board (As per sample)area exceeding 1.00 sqm but not exceeding 1.50 sqm with 2-3 mm thick aluminium composite panel covered by encapsulated lens type retro reflecctive sheet (grade 3 m type II diamond grade) on both side with any colour base fixed on and including stainless teel frame of size 25mmx25mm and hand on 50 mm dia stainless pipe (fabricationwork from SS 304 material) of height upto 2.5m from the natural gound level to top and pot ebedded in ground with PCC 1 : 2 : 4 type B-2 (using 40 mm graded crushed stone aggregate) of size 45 cmx45cmx60 cm including necessary excavation and earh work complete all as specified and directed. Note :- shape/design of sign board as approval of GE. (ii) The letters and symbols etc on both side shall be as per site requirement and as approved the size and font of wording as per direction of GE. |
| 117 | Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed. |
| 118 | Taking down carefully copper/aluminium point wiring for light, fan, bell socket power slocket etc complete with boards, outlet boxes fittings and fixtures such as switchs, sockets, lamp holders bracket, ceiling rose etc complete all as specified and as directed |
| 119 | M&L for Surface conduit Point wiring complete with 1.5 sq mm single core multi stranded copper conductor PVC (FRLS) insulated unsheathed cable confirming to IS-694,1100 Volts grade ISI Marked , class V in PVC conduit (ISI Marked) not less than 20 mm dia heavy duty with accessories etc and including sunken pressed steel terminal boxes in wall, including 1.50 sq mm PVC insulated unsheathed stranded copper conductor (FRLS) cable for common earth and connecting to earth dolly, suitable for One light/fan/bell point controlled by one, one way switch, complete all as specified and directed by Engr-in-Charge. |
| 120 | All as per Sr. item No. 119.00 here-in-above, but suitable for One socket outlet 3 pin 5/6 Amps on same board |
| 121 | All as per Sr. item No. 119.00 here-in-above, but suitable for One socket outlet 3 pin 5/6 Amp on independent board |
| 122 | All as per Sr. item No. 119.00 here-in-above, but with using 2.5 Sq mm single core multistanded copper conductor cable (FRLS) and 2.5 sq mm PVC insulated unsheathed stranded copper conductor(FRLS) for common earth wire for 6 pin 16 Amp socket outlet on independent board . |
| 123 | M&L for Point wiring complete with 1.5 sq mm single core multi stranded copper conductor PVC (FRLSH) insulated unsheathed cable confirming to IS-694,1100 Volts grade ( ISI Marked) passing in PVC cassing-N-capping 25/32 mm width fixed on surface of wall/roof/ceiling withexisting/new sunken pressed steel terminal boxes including 3.00 mm thick plastic laminated sheet top cover and 1.50 sq mm PVC insulated unsheathed stranded copper conductor(FRLSH) cable for common earth and connecting to earth dolly, suitable for One light/fan/bell point controlled by one, one way switch complete all as specified and directed. |
| 124 | All as per Sr. item No.123.00 here-in-above, but suitable for One socket outlet 3 pin 5/6 Amps on same board |
| 125 | All as per Sr. item No. 123.00 here-in-above, but suitable for One socket outlet 3 pin 5/6 Amp on independent board |
| 126 | All as per Sr. item No. 123.00 here-in-above, but with using 2.5 Sq mm single core multistanded copper conductor cable(FRLSH) including 2.5 sq mm PVC insulated unsheathed stranded copper conductor(FRLSH) for common earth wire for 6 pin 16 Amp socket outlet on independent board . |
| 127 | M&L for (concealed) point wiring complete with multistranded copper conductor 1.5 Sqmm PVC insulated unsheathed single core (FRLSH) cable 1100 volt grade, confirming IS 694 & colour code in conduit system of wiring, drawn through in and including non-metalic PVC concealed (including Cutting Chases and make good the distrubed surfaces as per existing finishes) conduit of size 20 mm or med grade as required as site, totally concealed in walls / and surface on floors / ceiling or fixed on surface of walls / columns / beam / tie beam etc by means of saddles and clips etc incl all conduit accessories / fittings / junction boxes / inspection covers etc of heavy grade, ISI marked and sunk terminal boxes of CI or 16 SWG pressed steel housing, totally concealed in walls with 3mm thick industrial laminated sheet top cover, fixed flush with wall surface by means of brass screws and sunk / cup washers, for mounting of switches, sockets fan regulators etc incl 1.5 Sqmm (FRLSH) PVC insulated, unsheathed flexible multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, suitable for One light/fan/bell point controlled by one, one way switch, complete all as specified and directed.Note:- The rates of chase cutting on wall done concealed conduit & making good good the distrubed surfaces as per existing finishes and steel terminal boxes are included in the unit rates |
| 128 | All as per Sr. item No. 127.00 here-in-above, but suitable for One socket outlet 3 pin 5 amps on the same board controlled by one no 5 Amp switch.2 |
| 129 | All as per Sr. item No. 127.00 here-in-above, but suitable for One socket outlet 3 pin, 5 Amps on independent board, controlled by one no 5 Amp switch. |
| 130 | All as per Sr. item No. 127.00 here-in-above, but with using 2.5 Sq mm single core multistanded copper conductor cable (FRLSH)including 2.5 sq mm PVC insulated unsheathed stranded copper conductor(FRLSH) for common earth wire for 3 pin 16 Amp socket outlet on independent board . |
| 131 | S&F switch piano, flush type, single pole, one way, 6 Amps, 230 Volts complete all as specified and as directed. |
| 132 | S&Fswitch piano, flush type, single pole, one way, 16 Amps, 230 Volts complete all as specified and as directed. |
| 133 | Supply and fix socket out let 2 in 1, 3 pin, 6 amp suitable for 6 Amp plug top 230 V complete all as specified & directed. |
| 134 | Supply and fix socket out let socket out let 2 in 1, 3 pin, 6 and 16 amp flush type suitable for 16 Amp plug top multipurpose 230 V, complete all as specified & directed. |
| 135 | Supply and fixing ceiling rose 3 terminals/PVC/Polycarbonate, isolated body complete all as specified and directed. |
| 136 | S&F lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed. |
| 137 | S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd. complete all as specified and directed. |
| 138 | Taking down and refixing of ceiling fan after servicing (cleaning, oiling and greasing) and connecting up including provision of cable from ceiling rose,complete all as specified and as directed . |
| 139 | Taking down and refixing of exhaust fan after servicing (cleaning, oiling and greasing) and connecting up including provision of cable from ceiling rose,complete all as specified and as directed . |
| 140 | S&F in replacement sheet metal enclosures 240 volt with suitable rated bus bar for double door IP-43 DB's of approved geauge suitable for one MCB SPN as incoming and 6 MCB SP as out going SPN 8 way complete all as specified and directed. |
| 141 | S&F in replacement sheet metal enclosures 240 volt with suitable rated bus bar for double door IP-43 DB's suitable for one MCB SPN as incoming and 10 MCB SP as out going SPN 12 way complete all as specified and directed. |
| 142 | S&F in replacement sheet metal enclosures 415 volt TPN 4 way double door IP-43 DB's suitable for one TPN/ isolator 4 pole MCB as incoming and three TPN MCB as outgoing complete all as specified and directed . |
| 143 | Supply and Fix MCB Single pole\\"B\\" series 5-32 Amps (ISI marked) breaking capacity 10KA etc, incl dismantaling old unserviceable MCB SP complete all as specified and directed by Engr-in-charge. |
| 144 | Supply and Fix MCB Single pole & neutral \\"B\\" series upto 40 Amps (ISI marked) breaking capacity 10KA etc, incl dismantaling old unserviceable MCB SPN complete all as specified and directed by Engr-in-charge |
| 145 | Supply and Fix MCB Single pole & neutral \\"B\\" series upto 63. Amps (ISI marked) breaking capacity 10KA etc, incl dismantaling old unserviceable MCB SPN complete all as specified and directed. |
| 146 | Supply and fixing MCB TPN B Curve 63 to 100 Amps (ISI marked) breaking capacity 10KA etc,incl disntaling of old unserviceable TPN MCB complete all as specified and directed. |
| 147 | Supply and fixing in replacement LED lights fitting 1x 20W, 220V, Cool White, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 148 | S&F in replacement LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed. |
| 149 | Supply and fixing in replacement LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including 1.60 mtr long 40mm bore light grade GI pipe mounting bracket made to shape with and including MS clamp of F1 40 mmx6mm with bolts , nuts & washers and conductor to fitting with 3 core 1.5 sqmm pvc insulated cable, complete all as specified & directed. |
| 150 | Material and labour for (in existing location and position) taking out and refixing after repairs, including rewinding of Desert Cooler fan motor of any make, 3 speed,1400 RPM of capacity 1/5 HP with super enameled copper winding wire of appropriate size ( as per existing ) inclusive of Bush/Shaft/Ball bearing as per existing make/model, complete all as specified & directed. |
| 151 | S&F in replacement of oil filled capacitor 4.00 MFD for desert cooler fan motor , complete all as specified & directed. |
| 152 | Material and labour for replacement of bottom tank and top ( in existing location and position) of approx size - 750 X 750 X 200 mm ( as per existing ) for Desert Cooler made out of 18 gauge PGI sheet with and including two coats of synthetic enamel painting over one coat of red oxide primer on the new surfaces to match with existing surface outside and inside surface with approved quality paint including leakage testing , complete all as specified & directed. |
| 153 | Material and labour for ( in existing location and position ) replacement of front grill ( as per existing )( horizontal and vertical members moveable) of the Desert Cooler made out of 20 gauge PGI sheet with Name plate , complete all as specified & directed. |
| 154 | S&F in relacement ( in existing location and position) three speed selector switch, complete all as specified & directed. |
| 155 | Material and labour for replacement of side supporting columns to be fabricated out of 18 gauge PGI sheet of size 80x80x800 mm with and including necessary nut, bolts etc, complete all as specified & directed. |
| 156 | Material and labour for replacement of side/rear panel made out of 20 gauge PGI Sheet with suitable handles with and including two coats of synthetic enamel paint over one coat of red oxide primer to match with the existing desert cooler , complete all as specified & directed. |
| 157 | Material and labour for painting to old steel surfaces of Desert cooler capacity up to 5000 Cft with one coat of synthetic enamel spray paint hammer tone paint of approved colour over one coat of red oxide primer on external surface and one coat of anti corrosive black paint inside the Body tank and side grills over a coat of red oxide primer complete including complete removal on old surface of Desert cooler and writing of MES No etc complete at site or at E/M store yard, complete all as specified & directed. |
| 158 | Material and labour for replacement of Desert Cooler fan motor with super enameled copper winding wire capacity 1/5 HP three speed, Copper Winding not less than 1200 RPM single phase with aluminium fan blade, bracket supporting stand , complete all as specified & directed. |
| 159 | Material and labour for replacement of submersible pump of discharge head 2.5 Mtr 220-240 Volts AC Supply single phase 20 watt , complete all as specified & directed. |
| 160 | Material and labour for replacement of Wood wool pad for Desert Cooler of size 500 x 550 x30 mm (set of three pads) superior quality including binding properly with GI wire of 16 SWG , complete all as specified & directed. |
| 161 | Material and labour for replacement of MS weld wire mesh having apparture size 25 mm and fitted in side grills/rear, complete all as specified & directed. |
| 162 | Material and labour for replacement of PVC insulated and PVC sheathed cable copper conductor 3 core 1.0 Sqmm cross sectional area superior quality , complete all as specified & directed. |
| 163 | Material and labour for replacement of PVC water distribution cup of one inlet and 3 outlets fixed with MS nuts and bolts (as per sample by approved by GE), complete all as specified & directed. |
| 164 | Material and labour for replacement of PVC elbow suitable for desert cooler (as per sample) , complete all as specified & directed. |
| 165 | Material and labour for replacement of PVC pipe 15 mm dia heavy duty for Desert Cooler Pump , complete all as specified & directed. |
| 166 | Material and labour for painting to desert cooler stand with two coats of synthetic enameled paint of approved colour over one coat of red-oxide primer ,including complete removal of old surfaces of desert cooler stands , complete all as specified & directed. |
| 167 | Material and labour for replacement of motor fixing ring (not less than 25 mm width ) for desert cooler eight screw / clip type(asper sample) , complete all as specified & directed. |
| 168 | Taking down desert cooler installed at ground floor safely , including cleaning inside , outside , motor oilng sevicing and pump servicing including putting up in same location and position complete all as directed. |
| 169 | Supply and fix in existing location and position PTMT stop cock 15 mm dia high pressure screwed for iron pipe, complete all as specified & directed. |
| 170 | Supply and fix in existing location and position PTMT Ball valves 15 mm dia high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe , complete all as specified & directed. |
| 171 | M&L for wiring for circuit / sub main wiring alongwith earth wire with the following sizes of FR LSH PVC insulated , multistranded copper conductor cable ,( 2 X 1.5 Sq mm + 1X 1.5 Sqmm ), single core drawn in and including PVC casing capping 25 mm width , to be fixed on surface/ ceiling , complete all as specified & directed.Note :- Two runs of cable 1.5 Sqmm and One run of 1.5 Sqmm along with conduit shall be measured as one unit length. |
| 172 | Supply and replacement of 3 Pin Plug Top 06Amps ISI Marked 230 Volts , complete all as specified & directed. |
| 173 | Material and labour for replacement of PVC Connection pipe ISI Marked 300mm long heavy duty, complete all as specified & directed. |
| 174 | Material and labour for replacement of PVC stop cock 15mm dia ISI Marked heavy duty, complete all as specified & directed. |
| 175 | S&F in replacement PVC moulded box of switch socket combination of cap - 6 Amp, complete all as specified & directed. Please Enable Macros to View BoQ information |
| 176 | S&F in replacement PVC moulded box of switch socket combination of cap - 6 Amp, complete all as specified & directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
TodayJul 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender