|
| 1 | Demolition of brick/Stone masnory work built in cement mortar including all quions, arches, pillars, etc complete all as specified and directed. |
| 2 | Demolition of cement concrete in ground floors and paving (un reinforced) n exc. 15 cm. thicknesses, below or above ground level complete all as specified and directed. |
| 3 | Demolition of reinforced cement concrete in roof or any descsription complete all as specified and directed. |
| 4 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 5 | Boring holes 3.5m deep in soil for single under reamed piles and getting out and disposal of soil to a distance n.exc 50m (dia of pile 300mm) complete all as specified and directed. |
| 6 | Excavation in trenches in soft/ loose soil not exc 1.5m wide and not exc 1.5m deep for foundation, pier holes etc n. exc 10 sqm on plan and getting out complete all as specified and directed. |
| 7 | M&L plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate in foundation, filling and mass concrete complete all as specified and directed. |
| 8 | M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips |
| 9 | All as per item above but 5mm dia and over in stirrups, spacers and binders complete. |
| 10 | M&L reinforced cement concrete M-25 design mix using 20mm graded stone aggregate as in foundations, footing, foundation beams, plinth beams, bases for columns, pedestal, under reamed piles, mass concrete, etc complete all as specified and directed. |
| 11 | M&L reinforcwed cement concrete M-25 design mix using 20mm graded stone aggregate as in columns, pillars, posts, struts etc complete all as specified and directed. |
| 12 | M&L reinforcwed cement concrete M-25 design mix using 20mm graded stone aggregate as in coping, beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and directed. |
| 13 | Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished surface of concrete complete all as specified and directed. |
| 14 | Formwork to sides of pillars, posts, struts, piers, columns and stanchions flat with rough finished surface of concrete complete all as specified and directed. |
| 15 | Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc on flat with rough finished surfaces of concrete complete all as specified and directed. |
| 16 | M&L for old size brick work with sub class 'B' Bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed. |
| 17 | Same as item No 16 above but except bricks.Note- Bricks retrived from demoltion shall be used in this item. |
| 18 | Taking down cement plaster on wall/ceiling including raking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed. |
| 19 | M&L 15mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth (without using extra cement) complete all as specified and directed. |
| 20 | M&L 15mm thick cement plaster on other than fair faces of brick work or concrete surfaces with cement mortar 1:4 finished even and smooth (without using extra cement) complete all as specified and directed. |
| 21 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. |
| 22 | M&L for applying two coats of cement based paint on plastered wall surfaces over a coat of primer incl preparation of surfaces complete all as specified and directed. |
| 23 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed. |
| 24 | Removing excavated material exc 1.50 Km but n.exc 5 Km and depositing where directed at a level n.exc 1.5m above the staring point complete all as specified and directed. |
| 25 | S&F in repair for ornamental and intrinsic design gate or red iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work like for portions framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc and for ornamental and intricate design conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 26 | Preparation of new steel surfaces of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed. |
| 27 | S&F Mild steel work for fencing post and similar work including cutting tops to shape as directed, drilling holes, notching for wire, etc conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 28 | Removing building materials debris (other than excavated material) to a distance of 1 km including loading and dumping and leveling at the destination complete all as directed. |
| 29 | Excavation in post hole (or similar hole) each n exc 0.50 cum, getting out returning filling in and ramming earth or broken rubble mixed with earth around in layer n. exc 25 cm etc and getting out in soft/ loose soil complete all as specified and directed. |
| 30 | M&L for Mild steel round bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips conforming to Gd I, IS-432 (Part-I) Complete all as specified and directed. |
| 31 | Supply only Chain Link MS galvanized fencing of 4.00 mm dia of wire and mesh size 75 mmx 75 mm complete all as specified and directed. |
| 32 | Fixing Only Chain Link fencing including line wires, any mess, size and type to any type of standards, rails, straining bolts, etc including provision of binding wires, complete all as specified and directed. |
| 33 | Supply and fixing stretch and fix concertina coil 600mm dia in stress position hot deep galvanised steel wire coated with CLR anti corrosive paints making diamond shape with the help of dove tail clips (18 SWG), the concertina coil is to be fixed with barbed wire at points where coil touched the bottom barbed wire with the help of lug rings (24 SWG) including all fittings like fastener clips, steel lug rings etc complete all as shown in drg all as specified and directed. Note: (i)Stretch length of each coil shall be 6 mtr. (ii)weight of each coil shall not be less than 9kg. |
| 34 | S&F Galvanised 2 strand steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts including securing or typing at crossing with and provision of galvanised MS wire stapples or steel pins etc as directed (each line wire to be measured). Please Enable Macros to View BoQ information |
