Tender For Special Repair To Aps Building At Mic&S Ahilyanagar
Tender Value
58.27 Lakhs
Estimated cost
Bid Submission
14 Jul 2026
7 days left
EMD
1.13 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
GE SOUTH AHILYANAGAR → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Aps Building At Mic&S Ahilyanagar
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling kota, granite, cudappah stone slabs and interlocking tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortor complete all as specified and as directed. |
| 2 | M&L for machine cut Kota stone flooring 18 to 22 mm thick (size of kota stone slab 22\\"x22\\") laid over and including 20 mm thick bedding layer of cement mortar 1:6, jointed with grey cement slurry mixed with pigments to match the shade of slab including cutting, rubbing and mirror polishing including removing dust complete all as specified and as directed. |
| 3 | All as per item No 2 here in before but 15-18 mm thick as in risers to steps and skirting laid over and including backing coat of 10mm thick in cement mortar 1:3 all as specified and as directed. Note : Risers provided to steps shall be in one piece. |
| 4 | M&L for machine cut Kota stone slabs 18 to 22 mm thick as in treads of steps of stair case in single piece with 2 nos V groove cutting laid over and including 10 mm thick cement screed bed in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including, rounding and moulding edges, rubbing and mirror polishing complete all as specified and as directed. |
| 5 | M&L for machine cut cudappah stone slab 20-25mm thick for cooking platform, verticals of wash basins and sinks etc including cutting chases in wall and fixing the slab in cement mortar including rubbing and polishing complete all as specified and as directed. |
| 6 | M&L 18 to 20mm thick pre-polished granite stone slab of approved shade and colour as in table top, top of WHB, kitchen slab/platform, gate pillars, cills etc or on vertical surfaces including vertical projection, urinal partition, including full round moulding the edge, laid over and including screed bed 20mm thick in cement mortar 1:4 jointing, pointing in white cement 1:2 using marble dust with admixture or pigment to match the shade of granite and rubbing, polishing to achieve mirror finish complete all as specified and as directed.Note : Colour and shade shall be as approved by GE. |
| 7 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing rubbish off the premises complete all as specified and directed. |
| 8 | M&L for glazed white ceramic tiles in vertical surfaces as dado of size 450x300x6-7mm/300mmx600mmx6-7mm, thick set and jointed in neat cement and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:3 on other than fair faces of brick work etc complete all as specified & directed.Note: Size and shade shall be as approved by Engineer-in-charge |
| 9 | M&L for non skid coloured ceramic tiles 7-8mm thick (square or rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 etc complete all as specified & directed.Note: Color and shade shall be as approved by Engineer-in-charge |
| 10 | M&L for non skid coloured ceramic matt finished tiles 7-8mm thick (square or rectangular) area of each tile exceeding 0.42 sqm but not exceeding 1 sqm (600X1200 mm) in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified & directed.Note: Color and shade shall be as approved by Engineer-in-charge |
| 11 | Excavation over areas n. exc 1.50m in depth in any type of soil for foundation etc all as specified and as directed |
| 12 | Excavation in trenches not exc 1.50m wide and not exc 1.50m deep for foundation etc . or for shafts, wells, cesspits, manholes, pier holes, etc. n. exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and as directed |
| 13 | Removing excavated soil to distance not exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and as directed |
| 14 | M&L for moorum filling in floors or paving, laid in layers n.exc. 15cm thick, spread, levelled and rammed including watering complete all as specified and as directed. |
| 15 | M&L for hard core of gauge exc. 63 mm but n. exc. 100 mm, deposited spread and levelled in layers n. exc. 15cm thick, including watering and rammed etc. complete all as specified and as directed. |
| 16 | Demoltion of cement concrete (un-reinforced) in ground floors and paving not exc 15cm thickness (below or above ground level) complete all as specified & directed. |
| 17 | M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed. |
| 18 | M&L for 100 mm thick Type D2 1:4:8 (20mm graded aggregate) in floor slabs complete all as specified and as directed |
| 19 | M&L for Providing cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate in roof kerbs in lintels upto 1.5 m clear span, cills, steps ; seismic and other similar bands , plinth courses , string courses lacing courses, parapets and railings coping ,kneelers , apex stones , bed plates ,water throughs and the like including weathering , slightly rounded or chemfered angles and throating complete all as specified and as directed . |
| 20 | Demolition of brick/ block/ stone masonry built in cement mortar or cement lime mortar of any description. |
| 21 | M&L for Walling of random rubble, uncoursed masonary, built in cement mortar 1:4 complete all as specified and as directed. |
| 22 | M&L for brickwork with old size fly ash bricks straight or curved on plan with mean radius exc 6m built in CM 1:6 complete all as specified and directed. |
| 23 | M&L for raised pointing to random rubble masonry, uncoursed or brought to course in cement mortar 1:3, including racking out joints etc. complete all as specified and as directed. |
| 24 | Taking down cement or cement lime plaster of any description on brick, block or stone walls etc (at any height) including racking out joints, hacking for key scrubbing down with water etc complete & removing debris outside MD land as directed. |
| 25 | S&F GI wire netting 0.90mm dia and 12mm size of mesh and fixed to wall, ceilings, beams etc including all laps and waste including making V groove in crack portion n exc 10mm deep and n exc 10mm face and filled with 10mm thick cement mortar 1:3 etc complete all as specified and directed. |
| 26 | M&L for 15 mm thick rendering in cement mortar 1:4 (using water proofing liquid as per manufacturers instruction) on other than fair faces of brick masonry surfaces or concrete surfaces, finished even and fair without using extra cement complete all as specified and as directed. |
| 27 | M&L for rendering 10 mm thick in CM 1:6 on fair faces of brick/concrete surfaces finished even & smooth without using extra cement etc complete. |
| 28 | M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces as in ceiling finished the surface even & smooth without using extra cement including sagol finish complete all as specified & directed. |
| 29 | M&L for preparation of new plastered internal surfaces of ceiling and applying three coats of white wash of required shade and colour complete including one coat of alakli resistant primer as per manufacturer's specifications in any colour complete all as specified and directed. |
| 30 | M&L for preparation of new plastered internal surfaces of wall and applying two coat of acrylic distemper of required shade and colour complete including one coat of alakli resistant primer as per manufacturer's specifications in any colour complete all as specified and directed. |
| 31 | M&L for preparation of surface old or newly plastered surfaces of walls and applying minimum 1.5 to 2 mm thick wall care putty complete all as specified and directed. |
| 32 | M&L for Newly plastered wall surfaces, preparation of surface and applying two or more coats of 100% premium exterior acrylic emulsion paint, Alkali & fungal resistance, dirt resistance, of required shade over and including priming coat of exterior alkali resistant primer applied @ 0.90 litre/ 10 sqm on prepared surface of brick (plastered or un-plastered) or concrete surface complete all as specified and directed by Engr-in-charge. |
| 33 | M&L for preparation of old plastered or unplastered decorated ceiling surfaces including filling of cracks/holes by acrylic crack filler and applying two coats of white wash complete all as specified and as directed by Engineer-in-Charge. |
| 34 | M&L for applying two coats of acrylic distemper on prepared old decorated surfaces of walls (plastered or unplastered) using roller all as specified and as directed by Engineer-in-Charge. |
| 35 | M&L for preparation of old concrete & brick surfaces of any description over 10cm girth or width, not otherwise described and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and as directed. |
| 36 | M&L for complete removal of existing treatment on wall/roof projections including facia, cornices, etc by scrapping with mechanical sander (having mechnical vaccum mechanism ) with sanding pad of appropriate grit to make surface clean, free from dust, loose paint etc by skilled labour including filling of cracks/holes by crack filler and applying one coats of exterior acrylic emulsion paint, Alkali & fungal resistance, dirt resistance, of required shade over and including priming coat of exterior alkali resistant primer applied @ 0.90 litre/ 10 sqm on prepared surface of brick (plastered or un-plastered) or concrete surface complete all as specified and directed by Engr-in-charge. |
| 37 | M&L for preparation of new steel surface of any description over 10cm in width or girth and applying two coats of synthetic enamel paint of any shade over a coat of red oxide primer complete all as specified and directed. |
| 38 | M&L for preparation of old painted surfaces of steel of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 39 | M&L for preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats of Creosote complete all as specified and as directed. |
| 40 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n. exc 1.5 sqm each and making good the disturbed surface in CM 1:3 complete all as specified and directed. |
| 41 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm but n exc 4 sqm each and making good the disturbed surface in CM 1:3 complete all as specified and directed. |
| 42 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative flush/panel door shutter of 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. |
| 43 | M&L for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ ceosetory windows & other frames/ chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension grade), Calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), minimum compressive strength of 58 N/Sqmm, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per specified and as directed. Note: (i) Minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable for WPC solid door/window frames. Variation in profile dimensions on plus side shall be acceptable without any extra cost to the department.(ii) M.S. hold fast/ lugs or SS dash fasteners shall be paid separately. |
| 44 | S&F powder coated aluminium door with frame and shutter in two panels (top and bottom) made out of aluminium sections (make Jindal or equivalent) including 5 mm thick sheet glass, aluminium cleats, rubber/ neoprene beading, all necessary fittings and locking arrangements etcall as specified and as directed and comprises of following sections :- (a) Vertical style- 47 x 44.5 x 2.25 mm thick @ 1.15 Kg/m (Min)(b) Lock rail- 114.6 x 44.45 x 2.3mm thick @ 2.06 Kg/m (Min)(c) Bottom rail-114.6 x 44.45 x 2.3mm thick @ 2.06 Kg/m (Min)(d) Frame-47.5 x 44.45 x 2.25 mm thick @ 1.12 Kg/m (Min) |
| 45 | S & F powder coated aluminum windows, three track, made out of aluminium sections including all necessary fittings, 5mm thick sheet glass, rubber/ neoprene beading, locking arrangements all as specified and as directed and comprising of following sections :- (a) Window frame: (i) Bottom-Section 20671 (Wt not less than 0.699 Kg/m) (ii) Top & Side - 20672 (Wt not less than 0.594 Kg/m)(b) Shutter: (i) Vertical (end)- 20669 (Wt not less than 0.548 Kg/m) (ii) Vertical (lock) - 20689 (Wt not less than 0.481 Kg/m) (iii) Bottom - 20718 (Wt not less than 0.263 Kg/m) (iv) Top - 20668 (Wt not less than 0.377 Kg/m)Note : Shade shall be as approved by Engineer-in-Charge. |
| 46 | S&F in repairs powder coated Anodised aluminium ventilator having aluminium section weighing 0.55 kg/m, sliding louver type of size 300mm x 600mm having powder coated 6 aluminium louvers including necessary joining cleats, glazing clips, screws, glass etc. complete all as specified and as directed. |
| 47 | S&F aluminum anodized barrel tower bolt of extruded section size of bolt 150mm as specified and directed. |
| 48 | S & F 300 mm long aluminum alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of steel, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy complete all as specified and as directed. |
| 49 | S&F 100 mm long SS butt hinges, medium weight, cold rolled and fixed with screws/welded complete all as specified and directed. |
| 50 | S&F 150mm size aluminium alloy handles, fabricated type extruded section, ISI marked complete all as specified and as directed. |
| 51 | S&F continous (Paino) hinges, brass finish of when open 30mm width of flaps complete all as specified and as directed. |
| 52 | S&F in repairs, 18 mm thick WPC Board (Wood Polymer Composite), termite proof, waterproof & screwable & nailable as in fabrication of storage System, cupboards in rooms/kitchen i/c Drawers, shelves, etc. laminated one side with decorative choice lamination and other side balancing white lamination, with teak wood lipping on the edges of the shutters and the box etc. including necessary fixing arrangement on walls with fasteners, complete all as specified and as directed by Engineer-in-charge. |
| 53 | S&F magnetic catcher, Double strip (horizontal type), in cupboard/ward robe shutters including fixing wit necessary Stainless Steel screws etc. complete all as specified and as directed. |
| 54 | S&F in repairs aluminium extruded section door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 55 | S&F in repairs aluminium extruded section door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysJul 21, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender