Tender For Smart Comprehensive Repairs To Ge Office, Bso Office, Mes Qts, Bso Yard, Storage Accn And Ancillaries Along With Certain Repairs In The Area Of Age B/R-Ii Under Ge (N) Ahilyanagar.
Tender Value
49 Lakhs
Estimated cost
Bid Submission
08 Jul 2026
0 days left
EMD
98000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Garrison Engineer (North) Ahilyanagar → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Smart Comprehensive Repairs To Ge Office, Bso Office, Mes Qts, Bso Yard, Storage Accn And Ancillaries Along With Certain Repairs In The Area Of Age B/R-Ii Under Ge (N) Ahilyanagar.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling, floor, hearth or wall tiling including cement mortar bedding/ backing and removing all rubbish/ dismantled material outside MD Land. |
| 2 | Demolition of plain cement concrete (unreinforced) in ground floor not exceeding 15 cm thick all as directed. |
| 3 | M&L Excavation over areas,n exc 1.5 m deep and getting out soft/ loose soil complete all as specified and directed by Engg-in-cgarge. |
| 4 | Returning, filling in excavated material (soil) including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft / loose soil etc complete all as specified and directed by Engineer-in-Charge |
| 5 | Removing excavated material exc.250m but n exc. 500m and deposited where directed. |
| 6 | M&L for 75 mm thick plain cement concrete 1:4:8 type D2, using 40 mm graded stone aggregate as in sub base all as directed. |
| 7 | M & L for plain Cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete etc complete all as specified and directed by Engineer-in-Charge |
| 8 | M&L for Glazed colour ceramic tiles 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match coloured as approved by GE as in dado / skirting or on vertical surfaces, over and including 10 mm thick backing coat in CM (1:4) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile etc complete all as specified and directed. |
| 9 | M&L for joint free / rectified anti skid ceramic coloured tiles 7-8mm thick matching to dado tiles area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,(400x400)mm as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed. |
| 10 | M&L for joint free / rectified vitrified/ ceramic light shade coloured tiles 8-10 mm thick as approved by GE (square /rectangular) area of each tile not exceeding 0.36 sqm,(600 x600)mm as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6 ) set and jointed with white or coloured cement to match the shade of tile etc complete all as specified and as directed |
| 11 | .-Ditto- all as per ser item No 10 above but on skirting and backing coat of 10 mm thick in CM 1:4 |
| 12 | Dismantling of stone slabs and tiles of any description or thickness in floors, approns etc laid and bedded in any mortor and removing all rubbish/dismantled material outside MD Land. all as directed. |
| 13 | M & L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed by Engineer-in-Charge. |
| 14 | S&F 15-18 mm thick pre-polished granite stone slab of approved shade and colour Jet Black / Telephone Black as in top table, top of WHB, kitchen slab/platform, steps, gate pillars, cills, jambs, lintel etc or on vertical surfaces including vertical projection, full round moulding the edge laid over screed bed 15mm thick in CM 1:4 jointing , pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite and rubbing polish to achieve mirror finish complete all as specified and directed. |
| 15 | S&F machine cut cudappah stone slab 20-25 mm thick over cement screed base, laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing all as directed. |
| 16 | M&L for 20 mm thick Rough dressed(shahabad) lime stone slab flooring, laid dry, jointed and pointed in cement mortar 1:3 as in floor/plinth etc over bedded and jointed in cement mortar 1:6 and pointed in cement mortar 1:3 in floor/plinth etc over and incl 15 mm thick screed bed in CM 1:6 complete all as specified and directed |
| 17 | Fixing only 20 mm thick rough dressed Shahabad stone as in floor/plinth etc over and incl 15mm thick screed bed in CM 1:6 including dismantling complete all as specified and directed |
| 18 | M&L for heavy duty vitrified paver tiles 30cm x 30cm x 10mm thick,approved by GE withnset,jointed and pointed in neat cement slurry with grey cement and pigment to match in floors,over and including screed bed or bedding a layer of 15 mm in cement mortar 1:6 complete all as specified and directed by Engg-in-charge. |
| 19 | Demolition of plain cement concrete solid block masonary built in cement mortar & removing all rubbish/dismantled material outside MD Land.all as directed. |
| 20 | M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge. |
| 21 | Taking down cement plaster on brick / stone walls including raking out joints, hacking for key, scrubbing down with water all as directed |
| 22 | M&L for rendering, 12 mm thick on stone surfaces in cement mortar 1:6 surfaces finished even and fair finish all as specified and directed. |
| 23 | M&L for rendering, 10 mm thick on brick/concrete surfaces in cement mortar 1:6 surfaces finished even and fair finish all as specified and directed. |
| 24 | M&L for rendering, 15 mm thick on stone/brick/ concrete surfaces in cement mortar 1:4 surfaces finished even and fair finish all as specified and directed. |
| 25 | M&L for 2 mm wall care putty on walls complete all as specified and directed by Engg-in-charge. |
| 26 | Dismantling of single layer manglore pattern in roofing & removing all rubbish/dismantled material outside MD Land.all as directed. |
| 27 | .-ditto- all as ser item no 26 above but bedded in cement morter |
| 28 | M&L for roofing tile, manglore pattern interlocking at sides joints laid dry |
| 29 | .-ditto- all as ser item no 28 above but except manlore pattern tiles |
| 30 | M&L Ridge or hip tiles to suit mangalore pattern of roofing tiles, bedded and jointed in cement morter 1:6 |
| 31 | Dismantling in fillets,rails, posts, rafters purlins etc under 40 sqcm in section framed work & removing all rubbish/ dismantled material outside MD Land. |
| 32 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including ridge & removing all rubbish/ dismantled material outside MD Land.all as directed. |
| 33 | S&F Pre-painted Galvalume sheet shall be 0.50mm thick (total coated thickness), 550 Mpa minimum, yield strength. It shall be coated with hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having overall width and laid width as specified and shall be fixed using hot dip galvanized, self drilling and self tapping screws neoprene and EPDM washers. Penetrations and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc.complete all as specified and directed by Engg-In-charge. |
| 34 | Supply and fix 0.50 mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with, 550 Mpa minimum, yield strength. It shall be coated with hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having overall width and laid width as specified and shall be fixed using hot dip galvanized, self drilling and self tapping screws neoprene and EPDM washers. Penetrations and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc.complete all as specified and directed by Engg-In-charge. |
| 35 | S&F Steel work in tubular trusses Roof trusses (framed) of section Rectangular/ square/ circular, post, trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161- 2014 and IS 4923- 2017 grade St.-240. |
| 36 | Supply and fix in repairs vitreous china wash down water closet (Pedestal pattern) white including fixing bolts with and including plastic water closet seat cover closed pattern with flat bottom and cover and MSCP almn hinges device complete connecting to 'P' or 'S' trap all as directed. |
| 37 | Supply and fix in repairs vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistren complete all as specified and directed. |
| 38 | Supply and fix in repairs wash hand basin vitreous China, flat back of size 550 X 400 mm including a pair of brackets, PTMT waste coupling, 32 mm dia PVC flexible waste pipe and connecting to stop valve and nahani trap all as directed. |
| 39 | M&L for preparation of new unplastered or plastered surfaces and applying two coats of oil bound distemper including chalk whitening on wall including smooth roller finish complete all as directed. |
| 40 | M & L for preparation of newly plastered surface of wall and apply two coats of cement based paint over a coat of alkali primer any height including scaffholding etc complete all as directed. |
| 41 | Taking down chowkats or frames exc 1.5 Sq m but nexc 4.00 sqm with shutters (without taking off shutters from the frames) all as directed. |
| 42 | Taking down chowkats or frames n exc 1.5 Sq m with shutters (without taking off shutters from the frames) all as directed. |
| 43 | Taking down shutters of any description exc 1 sqm and n exc 2 sqm each all as specified directed by Engineer-in-charge. |
| 44 | Taking down shutters of any description n exc 1 sqm each all as specified directed by Engineer-in-charge. |
| 45 | S & F Pressed steel door frame of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hings, lock strike plate, etc, complete all as specified, |
| 46 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction ofEngineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 47 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 48 | Supply and fix 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides |
| 49 | Supply and fix 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) all as directed. |
| 50 | Supply and fix solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, all as directed. |
| 51 | Supply and fix Factory Made Solid PVC Moulded Door Shutter, with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC Sheet on back face |
| 52 | Supply and fix galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples all as directed. |
| 53 | Supply and fix mild steel butt hinges medium weight cold rolled of size 100mm |
| 54 | Supply and fix aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section of cast aluminium alloy and fixed 300mm long. |
| 55 | Supply and fix aluminium anodised barrel tower bolt of extruded section 200mm long. |
| 56 | Supply and fix aluminium anodised handles of extruded section 150mm long. Please Enable Macros to View BoQ information |
| 57 | Supply and fix aluminium anodised handles of extruded section 150mm long. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 17, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
TodayJul 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender