|
| 1 | Chair CB Steel W/ArmDrawing No FD-75(M)Overall size shall be 535mm wide,560mm deep and 900mm high. Seat shall be 455mm high from floor. Frame of chair shall be made out of mild steel conduit of 25mm dia (Outer) with 1.60mm wall thickness. Timber for seat, back rest and arm shall be Ist class teak wood. Canning shall be done with 2mm wide and 0.4 mm thick plastic cane half round of superior quality, white colour. Pattern of weaving shall be Godrej pattern. Width of cane for border and strengthening band shall be 3.5mm. The wooden seat frame shall be further supported by steel strips measuring 19mm x 3mm at the front and the rear and each strip shall be welded to ERW frame.The seat and back shall be fixed by providing suitable nut bolts and washers..Bottom of legs shall have hard rubber shoes. All iron surfaces exposed to direct view shall be painted with two coats of paint over a coat of primer after preparation of steel surfaces. Painting shall be done with spray machine to achieve smooth surfaces. |
| 2 | Mazagine Rack mediumDrawing No FD-365Overall size shall be 1200mm long, 800mm high and 100mm wide or deep.Back shall be of 12mm thick MDF board.The vertical partitions(05 in nos) shall also be of 12mm thick MDF board.The horizontal rails of teak wood 10mm thick and 50mm wide (04 in nos) shall be fixed on back as shown on drg .The 16 equal partitions made so far shall be provided with acrylic transparent persepex sheet 3mm thick in slanting in 5mm groove made in vertical paritions.The top left and right back shall be provided with a key plate for hanging purpose.The all edges of MDF board shall be covered with 4mm thick teak wood beading.All wood and teak veneer surfaces shall be french polished with high gloss finish. |
| 3 | Stool dressingDrawing No FD-252Stool dressing shall be manufactured to the shape, size and design as shown on drawing. Timber species shall of super group as per IS 13622:1993 with permissible moisture content. Caning shall be done without any joint in the cane. The cane shall be 2mm wide 0.4mm thick for seat and 3.5mm wide cane shall be used for border. Caning shall be done in Godgrej pattern. All exposed wooden surfaces shall be french polished to glossy finish. Rest all as per drawing. |
| 4 | Table office clk steelDrawing No FD-1004Overall size shall be 1200mm long, 610mm wide and 760mm high.Steel frame shall be of size 1160x570x742mm .four legs of 25mm mild steel tube of 1.6mm wall thickness shall be provided. Top of legs shall be joined together with 25mm square mild steel tube of wall thickness 1.6mm in long and short sides. Two short stiffeners of same size shall be provided at 130mm from bottom of legs. One long stiffener shall also be provided to the middle of short stiffeners. Three drawers of equal size shall be provided on the right hand side above the stiffener at 130mm high with overall size of 350mm wide and 430mm high and 410mm deep..The top of table shall be provided with pre-laminated MDF board of 18/19mm thick with teak veener shade and 4mm thick teak wood edging alround the table .Hard rubber/PVC toes shall be provided to the legs.Locking device shall be provided to drawers. All steel surfaces exposed to view when placed in position shall be painted with two coats of silver grey hammer paint internally and extrenally with spray machine after preparation of surfaces.A mark of MES shall also be provided on top left corner of front shutter with visible colour. Painting shall be done with spray machine.Rest all as per drg. |
| 5 | Table Card for 4 personDrawing No FD-352Over all size shall be 900mm long, 900mm wide and 760mm high. All wood shall be of teak wood of first class quality (MP teak). Four legs shall be 55mmx35mm in section and 741mm high joined together with teak wood plank of 20mmx100mm in section except 345mm width of drawer. where teak wood plank shall be of 20mmx40mm. Four stiffeners of 20mmx100mm in section 441mm long shall be provided with the sides of drawers making four equal spaces to have four drawers of 300mm x300mm (internal width). On one side of the drawers 20mmx60mm in section 349mm long fillets shall be provided to fill the gap wher ewooden leg is 55mm wide. 25mmx25mm in section 349mm long teak wood fillet shall be provided at the bottom side of 20mmx100mm fornt plank flushing the bottom edge with bottom of fillet on bots sides of drawers. Track rails flushing with top edge of drawer shall be provided on both sides of the drawers which shall be of 25mmx25mm in section and 349mm long having a rebate of of 12mmx12mm in section for the guide rails. Sides, back of drawer shall be of 19mm thick teak wood plank 60mm high. Sides shall be 349mm long and back shall be 324mm long. The bottom of drawer shall be of 6mm thick ply wood commercial and provided to have the drawer spaces as 300mmx300mmx40mm. Front teakwood plank of drawer shall be of 20mmx60mm in section and 399mm long. 5mmx5mm in section groove shall be provided on visible portion of top of legs when placed in position. Top shall be of 19mm thick particle bd commercial over which best quality green Baize cloth shall be fixed turned downwards to cover the top edges and again turned inside up to 15mm. Teak wood edging, 4mm thick and 19mm wide, shall be provided al-round the top of the table. All wood surfaces exposed to view when placed in position shall be French polished with high gloss finish preferably lacquer finish Eight corners of flat iron 25mmx3mm and 200mm long bent to right angle shall be screwed to the joints of legs and front panels. Where drawers are provided, the flat iron angles shall be housed in top and in legs by making rebate so that no hindrance shall be caused to smooth running of drawers. |
| 6 | Side boardDrawing No FD-241Side Board shall be manufactured to the shape, size and design as shown on drawing. Overall size shall be 1220mm long, 455mm wide and 760mm high. Four drawers shall be provided equally in this space. All wood surfaces exposed to view when placed in position shall be given high gloss French polish with lacquer fininsh. Rest all as per drawing. |
| 7 | Book case steelDrawing no FD-69Overall size shall be 1905mm high,915mm wide and 305mm deep. Mild steel sheet shall be 1mm thick. Skeleton type of shelving with enclosed back and sides fitted with seven shelves (including top and bottom) adjustable making six compartments. All joints and welding and fixing shall be done in accordance with the standard workmanship.All steel surfaces exposed to view when placed in position shall be painted with two coats of paint internally and extrenally with spray machine after preparation of surfaces.Rest all as per drg. |
| 8 | Sofa set double seaterDrawing No FD-281Overall size of one Seat shall be 670mm long and 745 mm wide and 530mm high up to arm rest level.The sofa set 2 seater shall consist of two single seats. All wood shall be of first class teak wood (MP).Legs of sofa set shall be 70mm x35mm in section teak wood . Front legs shall be jointed by 100mm x 35mm in section wooden rail in front . Front and rear legs shall be joined with 100mm x 35mm in section wooden rails in sides. 100mm thick seat cushion and back cushions shall be of size 530mm x 560mm (one numbers in seat and one numbers in the back). The cushion shall be of cool foam or any other superior quality foam of 40 density as approved by Engineer-in-charge. Cushion shall be covered with approved color tapestry cloth (approved by GE , not less than Rs:300/meter)or as directed byEngineer-in-charge.All wood surface exposed to view when placed in position shall be French polished with lacquer finish rest.Rest all as per drg. |
| 9 | Table office officers steelDrawing No FD-1003Over all size shall be of 1680x870 x760mm.25 mm MS square tube 1.6 mm thick shall be provide to frame 1 mm thick MS sheet nominal all around for drawer.Top shall be of 18mm thick pre-laminated MDF board ISI mark (exterior gde) one side decorative finish approved by GE and 4 mm thick teak wood edging all around shall be provided for top.Three drawers shall be provided on right hand sides of table.A cupboard with front openable door shall be provided on the left side of the table.A shelf shall aslo be provided at the middle of cupbaord.All sheet for drawers shelf and cupboard and back covering shall be 1mm thick.Hard rubber shoes shall also be provided to the bottom of legs.Rest all as per drgsAll steel surfaces exposed to view when placed in position shall be painted with two coats of silver grey hammer paint internally and extrenally with spray machine after preparation of surfaces.A mark of MES shall also be provided on top left corner of front shutter with visible colour. Painting shall be done with spray machine.Rest all as per drg. |
| 10 | Table centre 2-tierDrawing No FD-274Overall size shall be 900mm long, 450mm wide and 400mm high. All wood shall be of teak wood. Top of the table shall be of 18mm thick prelaminated MDF board of approved shade with 4mm thick teak wood beading all-round the edges of top.Bottom rail of teak wood of 20mmx50mm in section shall be provided between legs, widthwise at 100mm above the bottom of legs.The bottom tier shall be fixed on the top of bottom side rails with 50mm long screwss.The bottom tier shall be of 18mm thick prelaminated particle board exterior grade of approved shade with 4mm thick teak wood beading all-round the edges of both the tops.25mm dia hard rubber /PVC rings shall be fixed to the bottom of all legs fixed with 30mm long screws. All wood surfaces shall be French polished with high gloss finish. Rest all as per drawing. |
| 11 | Peg Set of 6 (wooden)Drawing No FD-80(M)Peg set of 6 shall be manufactured to the shape, size and design as shown on drawing. Overall size shall be 910 mm long, 75mm wide and 19mm deep. Timber species shall of super group as per IS 13622:1993 with permissible moisture content. Six brass pegs 80mm long shall be fixed over the wooden membrane with brass screws as shown in drg. Mild steel key plate shall be provided at both top corners of the peg set.All wooden surfaces shall be given high gloss French polish with lacquer finish. Rest all as per drg |
| 12 | Side Rack with tray steelDrawing No FD-1023Overall size shall be 840mm long, 355mm wide and 810mm high.Four mild steel angle iron 40mmx40mmx3mm shall be provided as legs and shall be 810mm high.The middle shelf shall be equally spaced between top and bottom shelves.The thickness of sheet shall be 1mm.Top shelf shall have three compartments or spaces equally spaced with 50mm high partition and back covering with mild steel sheet 1mm thick.All steel surfaces exposed to view when placedin position shall be given two coast of enamel paint over a coat pf primer after preparation of surfaces. Painting shall be done with spray machine. |
| 13 | Almirah medium steel with shelvesDrawing No FD-1032Overall size shall be 1270mm high,765mm wide and 440mm deep.The base shall be made of two numbers mild steel sheet channel base welded to bottom of almirah and shall be 100mm high. Mild steel sheet shall be 1mm thick for channel base. The base channel shall be welded at 50mm from each end of 765mm length and shall be up to full width of 440mm of almirah. Top, sides, back, bottom and front of almirah shall be of 1mm thick mild steel sheet. Three shelves equally spaced making four compartments shall be provided and shall be of 1mm thick mild steel sheet.Front shutters shall have two leaves.All joints and welding, fixing shall be done according standard workmanshipA steel chromium plated handle 100mm long shall be provided to the shutter.The locking device shall be three way locking device and shall also be provided with decorative key plate Make of Lock-Harrison/Godrej.All steel surfaces exposed to view when placed in position shall be painted with two coats of green hammerpaint over a coat of primer with spray machine after preparation of surfaces. A mark of MES shall also be provided on left top corner of front shutter of visisble colour as directed by Engr-In -Charge.Rest all as per drgs |
| 14 | Chair DraftsmanDrawing No FD-3(M)Chair Draftsman shall be manufactured to the shape, size and design as shown on drawing. Timber species shall of super group as per IS 13622:1993 with permissible moisture content. Caning shall be done without any joint in the cane. The cane shall be 2mm wide 0.4mm thick for seat and 3.5mm wide cane shall be used for border.Caning shall be done in Godgrej pattern All exposed wooden surfaces shall be french polished to glossy finish. Rest all as per drawing. |
| 15 | Table DraftsmanDrawing No FD-74(M)Table Draftsman shall be manufactured to the shape, size and design as shown on drawing. Timber species shall of super group as per IS 13622:1993 with permissible moisture content.All exposed wooden surfaces shall be french polished to glossy finish. Rest all as per drawing. |
| 16 | Almiarh large steel with shelvesDrawing No FD-1031Overall size shall be 1985mm high,920mm wide and 485mm deep. The base shall be made of two numbers mild steel sheet channel bases made in U shaped with ends covered . Mild steel sheet shall be 1mm thick. The base channel shall be welded at 50mm from each end of the length of 920mm and shall be up to full width of 485mm and shall be 100mm high Top, sides bottom and back of almirah shall be of 1mm thick mild steel sheet . Four shelves equally spaced of 1mm thick mild steel sheet shall be provided to make five compartments.Front shutter shall two leaves of equal size .Front shutter leaves shall have three butt hinges of 75mm fixed to each shutter and shall be side hung. All joints and welding and fixing shall be done in accordance with the standard workmanship.One chromium plated steel handle with a locking device shall be provided as shown on drawing .The locking device shall be three way locking device and shall also be provided with decorative key plate .Make of Lock-Harrison/Godrej.All steel surfaces exposed to view when placed in position shall be painted with two coats of silver grey hammer paint internally and extrenally with spray machine after preparation of surfaces.A mark of MES shall also be provided on top left corner of front shutter with visible colour. Painting shall be done with spray machine.Rest all as per drg. |
| 17 | Chair CB Steel w/o armsDrawing No FD-75Overall size shall be 535mm wide,560mm deep and 900mm high. Seat shall be 455mm high from floor. Frame of chair shall be made out of mild steel conduit of 25mm dia (Outer) with 1.60mm wall thickness. Timber for seat and back rest shall be Ist class teak wood. Canning shall be done with 2mm wide and 0.4 mm thick plastic cane half round of superior quality, white colour. Pattern of weaving shall be Godrej pattern. Width of cane for border and strengthening band shall be 3.5mm. The wooden seat frame shall be further supported by steel strips measuring 19mm x 3mm at the front and the rear and each strip shall be welded to ERW frame.The seat and back shall be fixed by providing suitable nut bolts and washers..Bottom of legs shall have hard rubber shoes. All iron surfaces exposed to direct view shall be painted with two coats of paint over a coat of primer after preparation of steel surfaces. Painting shall be done with spray machine to achieve smooth surfaces. |
| 18 | Table ConfrenceDrawing No FD-08Overall size shall be 2135mm long, 1065mm wide and 760mm high. Top shall be 25mm thick particle board with teak veneer finish on one side with 4mm thick teak wood beading alround the edges of the top fixed with headless nails and adhesive.All wooden surface shall be french polished with two coats after preparation of surfaces with high gloss finish. |
| 19 | Chair EasyDrawing No FD-229Chair Easy shall be manufactured to the shape, size and design as shown on drawing. Timber species shall of super group as per IS 13622:1993 with permissible moisture content. Caning shall be done without any joint in the cane. The cane shall be 2mm wide 0.4mm thick for seat and 3.5mm wide cane shall be used for border. Caning shall be done in Godgrej pattern. All exposed wooden surfaces shall be french polished to glossy finish. Rest all as per drawing. |
| 20 | Book shelf open large steelDrawing No FD-69Overall size shall be 1905mm high,915mm wide and 305mm deep. Mild steel sheet shall be 1mm thick. Skeleton type of shelving with enclosed back and sides fitted with seven shelves (including top and bottom) adjustable making six compartments. All joints and welding and fixing shall be done in accordance with the standard workmanship.All steel surfaces exposed to view when placed in position shall be painted with two coats of paint internally and extrenally with spray machine after preparation of surfaces.Rest all as per drg. |
| 21 | Chair easy steelDrawing No FD-121Chair easy steel shall be manufactured to the shape, size and design as shown on drawing. Timber species shall of super group as per IS 13622:1993 with permissible moisture content. Cushion shall be covered with approved upholstery (leatherite) of approved shade/colour (approved by GE)or as directed by Engineer-in-charge. All steel work shall b epainted with stove enamelled finishes to the required shade.All exposed wooden surfaces shall be french polished to glossy finish. Rest all as per drawing. |
| 22 | Chair writing with past and hand restDrawing No FD-120Chair shall be manufactured to the shape, size and design as shown on drawing. Timber species shall of super group as per IS 13622:1993 with permissible moisture content. Caning shall be done without any joint in the cane. The cane shall be 2mm wide 0.4mm thick for seat and 3.5mm wide cane shall be used for border.Caning shall be done in Godgrej pattern.All steel work shall b epainted with stove enamelled finishes to the required shade. All exposed wooden surfaces shall be french polished to glossy finish. Rest all as per drawing. |
| 23 | Receptacle PVCDrawing No FD/E6/MAP/13Plastic container with lid shall be of thick polymer plastic of best quality. Colour of container shall be bright i.e red /green/ blue as approved by GE. Handles of container shall be of best quality. Capacity of the receptacle shall be 20 Litrs. All other details shall be as shown on drawing. Make- Blowplast/ Supreme/ Cello/ Polyset/ Bright. |
| 24 | Desk stand LectureDrawing No FD-125(M)Desk Stand lecture shall be manufactured to the shape, size and design as shown on drawing. Timber species shall of super group as per IS 13622:1993 with permissible moisture content. All exposed wooden surfaces shall be french polished to glossy finish. Rest all as per drawing. |
| 25 | Charpoy IP hard topDrawing No FD/MAP-II/01Overall size shall be 1980mm long, 900mm wide and 440mm high. Two long rails and two short rails shall be of 25mmx65mmx16 gauge MS rectangular pipe .The legs shall be of size 32mmx32mmx16 gauge welded to long and short rails as shown on drg.Two stiffeners of size 25mmx25mmx16 gauge shall be provided in equidistant between two opposite long rails. Six number cleat of size 25mmx60mmx6mm shall be welded with frame to support ply. Two stiffeners joining legs of size 25mmx25mmx16 gauge shall be provided at 150mm from ground level .12mm thick commercial plywood shall be provided for top as shown on drg with proper nut and bolt .one nut and bolt shall also be provided at centre of each stiffeners for fixing the plywood irrespective of what is shown on drg..PVC hard rubber shoes shall be fixed at bottom of each leg. All steel surfaces shall be painted with synthetic enamel black in color before applying a coat of primer. Rest all as per drg |
| 26 | Chair WB w/o armsDrawing No FD-285Overall size shall be 445mm long,440mm wide and 835mm highTimber species shall of super group as per IS 13622:1993 with permissible moisture content. Front legs shall be of size 30mmx55mm in section and 435mm highand rear legs shall be of section30x55mm and 815mm high.The legs shall be joined by front ,sides, rear rails made to shape out of 30mmx65mm in section.Two side stiffeners in short rails shall be provided of 20mmx25mm in section.One stiffener of 20mmx25mm shall also be provided at centre of both sise stiffeners joining the sides stiffenres.12MM thick decorative plywood with perforated holes 5MM dia at centre in a radius of 5 inch shall be fixed over the frame of the chair irrespective of what is shown on drg. . All Dimensions, shape and size shall be followed as per drg. All joints, fixing shall be done in accordance with standard specifications. Rest all as shown on drg.All wooden expose surfaces shall be french polished two coats after preparation of surfaces |
| 27 | Table (900x900x760)mmDrawing No FD-291Table (900x900x760)mm shall be manufactured to the shape, size and design as shown on drawing. Timber species shall of super group as per IS 13622:1993 with permissible moisture content. All exposed wooden surfaces shall be french polished to glossy finish. Rest all as per drawing. |
| 28 | Chair VerandahDrawing No FD-359Chair Verandah shall be manufactured to the shape, size and design as shown on drawing. Canning shall be done with 2mm wide and 0.4 mm thick plastic cane half round of superior quality, white colour. Pattern of weaving shall be mat pattern. All steel surfaces shall be painted with two coats of white synthetic enamel paint over a coat of red oxide primerRest all as per drawing. |
| 29 | Almirah Steel mediumDrawing No FD-1032Overall size shall be 1270mm high, 765mm wide and 440mm deep. It shall be made of 1mm thick mild steel sheet/CRCA sheet . All joints shall be riveted and welded thoroughly. The almirah shall have three shelves. The almirah shall have one spring action recessed handle 150mm long with built in locking arrangement fitted to cut out space in one shutter with proper workmanship/normal handle 120mm with three way locking system. Rest all specifications and dimensions are as per drg FINISH:- The almirah shall be dry powder coated in double shade (shutter in off white and outer frame in steel grey after after preparation of surface . |
| 30 | Chair School with hand boardDrawing No FD/E6/MAP/05Over all size shall be of 585 mmWx300 mm Dx738 mm H. 25mm dia 16 Gauge MS tube shall be provided for steel frame. Paint synthetic enamel colour black 1st class shall be used two coats over a coat of primer. One piece PVC Seat and Back shall be provided. All Diamensions, shape and size shall be followed as per drg. All joints, fixing shall be done in accordance with standard specifications. Rest all as shown on drg. |
| 31 | Rack shoe steelDrawing No FD/E6/MAP/02(R)Overall size shall be 700mm long,300mm wide and 880mm high. The legs of the shoe rack shall be of 25mm dia MS pipe of 18 gauge. The five shelves of the rack shall be of 20mm dia MS pipe of 18 gauge welded to legs. The shelves shall have 3mm dia MS rod 9 Nos in widthwise and 3 nos in lengthwise welded to 20mm dia shelf frame. Pre treated with epoxy powder coated oven baked with ivory white colour/white/warm grey |
| 32 | Table bed sideDrawing No FD/E6/MAP/15(R)The overall size of the table bed side shall be 450mm x 450mm x 600mm from rear and 450mm x 450mm x 500mm from front as shown in drg.The entire frame of table bed side shall be made up of 18mm MS square pipe (18 Gauge) duly black powder coated. The two sides and top shall be made up of 18mm thick prelamainted particle board exterior grade. The Back of the table except the top portion as shown in drg shall be provided with 6mm commercial plywood BWR grade duly screwed to frame. The two sides, back and bottom of drawers of the table shall be made up of 12mm thick commercial plywood irrespective of what is shown on drg, except the front side which shall be of 18mm thick prelaminated particle board exterior grade. The drawers shall be made functional on teak wood runners fixed inside the tables shown on drg.The drawers of the tables shall be provided with 100mm long CP handles .Rest all as per drg. |
| 33 | Table pegDrawing No FD-384Overall size shall be 450mm long,300mm wide and 380mm high. Timber species shall of super group as per IS 13622:1993 with permissible moisture content. Irrespective of what is shown on drg,the top of table shall be 18mm thick BWR plywood of Grade-A with 1 mm thick laminated sheet pasted over the ply with marine grade adhesive and all edges of top shall be covered with 6mm thick teak wood beading. Irrespective of what is shown on drg a center stiffener of size 20x40mm shall be provided at center of side bottom rails for extra support. PVC hard rubber shoes of 25mm dia shall also be provided to bottom of each leg with 20mm long screws. Rest all specifications and dimensions are as per drg. All wooden surface shall be polished with high gloss Melamine polish in walnut shade after preparation of surfaces. Please Enable Macros to View BoQ information |
