Communications and Information Technology  Government Departments Closing in 0 days TDR #56007846

Tender For Construction Of Sub Fire Station Building Including Site Development Works At Kandaghat, Distt. Solan (Hp). (Civil And Electrical Work)

Issued by Government Departments · Kandaghat, Himachal Pradesh
Tender Value
2.80 Crore
Estimated cost
Bid Submission
01 Jul 2026
0 days left
EMD
5.61 Lakhs
Bank guarantee accepted
Document Fee
1770
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Kandaghat → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender for Construction Of Sub Fire Station Building Including Site Development Works At Kandaghat, Distt. Solan (Hp). (Civil And Electrical Work)

BOQ

Name of Work:- Construction of Sub Fire Station Building including site development works at Kandaghat, Distt. Solan (HP). (Civil and Electrical work)
Sl. No. Item Description
1Sub -Head : Earth Work
2Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge.
3All kinds of soil
4Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50 m and lift up to 1.5m, as directed by Engineer-in-Charge.
5Ordinary rock
6Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.
7All kinds of soil.
8Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50m.
9Ordinary rock
10Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :
11All kinds of soil
12Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia
13Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
14Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials.
15All kinds of soil.
16Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.
17Sub-Head - Concrete Work
18Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
191:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
201:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)
21Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc., up to floor five level, excluding the cost of centering, shuttering and finishing :
221:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
231:5:10 (1 cement : 5 coarse sand(zone-III) : 10 graded brick aggregate 40 mm nominal size).
24Providing and laying in position plum concrete with hard stone boulders in retaining walls etc up to all height and level, in required size and shape etc. with cement concrete of mix 1:3:6 (1 Cement : 3 Coarse sand : 6 Graded stone aggregate 40 mm nominal size) using 40 % hard stone boulders of size 100 mm to 150 mm, excluding cost centring and shuttering all complete as per the direction of Engineer-in-charge.
25Centering and shuttering including strutting, propping etc. and removal of form work for :
26Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc..
27Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation leveling & dressing & finishing the top smooth.
28Supplying & back filling with well graded stone boulders of size 150 mm to 300 mm behind retaining wall complete as per the directions of the Engineer-in-charge. (Note :- 30% deductions in measurements shall be made for voids).
29Providing and fixing 110 mm dia Rigid PVC pipe (working pressure 4 kg / sqcm) conforming to IS : 13592 type A in retaining walls for use as weep holes, laid to required slope complete as per the directions of the Engineer-in-charge.
30Sub-Head - Reinforced Cement Concrete
31Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :
321:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
33Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :
341:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
35Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources).
36Centering and shuttering including strutting, propping etc. and removal of form for :
37Foundations, footings, bases of columns, etc. for mass concrete
38Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
39Suspended floors, roofs, landings, balconies and access platform
40Shelves (Cast in situ)
41Lintels, beams, plinth beams, girders, bressumers and cantilevers
42Columns, Pillars, Piers, Abutments, Posts and Struts
43Stairs, (excluding landings) except spiral-staircases
44Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like
45Edges of slabs and breaks in floors and walls
46Under 20 cm wide
47Weather shade, Chajjas, corbels etc., including edges
48Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured).
49Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)
50Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto all levels
51Thermo-Mechanically Treated bars of grade Fe-500D or more.
52Smooth finishing of the exposed surface of R.C.C. work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand).
53Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections
54Making holes of 150mm dia and 100 to 200 mm depth in RCC slab by core cutting method or other suitable method for fixing SCI/ CI/ PVC pippes and sealing the joints with silicone adhesive and water sealant grout / white cement ro make water tight joint after fixing of pipes including scaffolding whereever requires all complete as per the direction of the Engineer-in-charge.
55Sub-Head : Masonry Work
56Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:
57Cement mortar 1:6 (1 cement : 6 coarse sand)
58Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :
59Cement mortar 1:6 (1 cement : 6 coarse sand)
60Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.
61Cement mortar 1:4 (1 cement :4 coarse sand)
62Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.ird course of half brick masonry.
63Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).
64Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).
65Sub-Head - Stone Work :
66Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level with :
67Cement mortar 1:6 (1 cement : 6 coarse sand).
68Sub-Head : Cladding Work
69Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.
70Granite stone slab colour black, Cherry/Ruby red
71Area of slab upto 0.50 sqm
72Area of slab over 0.50 sqm
73Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete
74Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinalpartitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finishedsmooth.
75Granite Stone of approved shade
76Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
77Sub-Head : Wood and P.V.C. Work
78Extra for providing frosted toughened glass panes 6 mm thick instead of plain float glass panes 6 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).
79Deduct for not providing hinges in doors, windows or clerestory window shutters with :
80ISI marked Stainless steel butt hinges with stainless steel screws :
81For 2nd class teak wood and other class of wood shutters
82Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:
8335 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
84Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws:
8535 mm thick shutters
86Second class teak wood
87Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25 mm with two chromium plated brass brackets fixed withC.P. brass screws and PVC sleeves etc., wherever necessary complete :
8825 mm dia
89Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessaryaccessories and screws etc. complete.
90Providing and fixing bright finished brass hasp and staple (safety type) with necessary screws etc. complete :
9190 mm
92Providing and fixing Stainless steel sliding door bolts transparent or dyed to required colour or shade with nuts and screws etc. complete :
93300x16 mm
94250x16 mm
95Providing and fixing SS tower bolts transparent or dyed to required colour or shade with necessary screws etc. complete :
96250x10 mm
97200x10mm
98Providing and fixing stainless steel handles transparent or dyed to required colour or shade with necessary screws etc. complete :
99125 mm
100Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.
101Twin rubber stopper
102Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of size 18X5 mm fixed with wooden adhesive of approved quality and screws/ nails on the edges of the Pre-laminated particle board as per direction of Engineer-in-charge.
103Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete.
104Double strip (horizontal type)
105Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.
106Providing and fixing to existing door frames.
10730 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames.
108Providing M.S. Piano hinges ISI marked IS : 3818 finished with nickel chromium plating grade 1 as per IS: 1068 and fixing with necessaryscrews etc., complete.
109Overall width 35 mm
110Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.
1111.0 mm thick.
112Providing & Fixing laminated sheet of in white / ivory shade of Century/Greenply/Merino make , inside of cupboard etc. with adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.
1130.8 mm thick.
114Providing and fixing powder coated telescopic drawer channels 300 mm long with necessary screws etc. complete as per directions of Engineer-in-charge.
115Providing and fixing MS powder coated set of five pegs (Hooks) of approved quality with MS screws all complete as per direction of the Engineer-in-charge .
116P/F PVC rubber Silencer on the rear side of door shutter to avoid collision between wall and door shutter as per directions of Engineer in Charge.
117Providing and fixing BWP Ply board conforming to IS: 710 of of Merino/ Greenply/ Century/Archid/Kitply , bonded with phenolformaldehyde synthetic resin in cupboards, shelves, shutters with necessary screws, nails and adhesive etc. all complete as per the direction of Engineer-in-charge
11818mm thick
119Providing and fixing 6mm thick BWP grade commercial ply of Merino/ Greenply/ Century/ Archid / Kitply , bonded with phenolformaldehyde synthetic resin in backing of cupboards, shelves, shutters with necessary screws, nails and adhesive etc. all complete as per the direction of Engineer-in-charge
1206mm thick
121Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc.
122After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod pf approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge.
123Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS:16231 shall be paid separately.
124Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for:
125(i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3
126(ii) Sites with structure height more than 20m for all wind speeds.
127Three track three panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.
128Using R3 series with frame (98mm & above) x (40mm & above) & sash (30mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on two end panels along with multi-point locking system (Height upto 1.8 meter).
129Fixed window / ventilator without mullion / transom
130Using R3 series with frame (55mm & above ) x (45mm & above) & mullion (55mm & above) x (65mm & above). (Height upto 2.5 meter)
131Providing and fixing fly proof stainless steel grade 304 wire gauge with average width of aperture 1.40 mm in both directions with wire of dia 0.50 mm to uPVC windows, doors & ventilators all complete with uPVC beading as per manufacturer's specification and direction of Engineer-in-charge. (Note :- uPVC beading to be paid in basic frame item).
132Providing and fixing glazing in uPVC windows, all complete with uPVC beading as per manufacturer's specification and direction of of Engineer-in-charge. ( Note :- uPVC beading to be paid in basic frame item). (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured).
1336mm thick toughened glass .
134Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC sliding window with necessary screws etc. complete.
135Sub-Head : Steel Work
136Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
137Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:
138Profile B - With Single Rebate of size 105 x 60 mm
139Fixing with adjustable lugs with split end tail to each jamb.
140Profile D - With Douible Rebate of size 125 x 60 mm
141Fixing with adjustable lugs with split end tail to each jamb.
142Modified Profile D - of size 125 x 60 mm with double/triple/four rebate to suit the shutters or fixed glass panes
143Fixing with adjustable lugs with split end tail to each jamb.
144Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.
145In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.
146Providing and fixing stainless steel ( Grade 304) railing & Grills for Windows made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
147Sub-Head : Flooring
148Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.
14940 mm thick with 20 mm nominal size stone aggregate
15052 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.
151Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete.
152Providing and laying full body & unglazed vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 , of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete.
153Size of Tile 600x 600 mm
154Providing and laying Full body and unglazed Vitrified tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make in all colours & shade in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.
155Size of Tile 600x600 mm
156Providing and laying GVT Vitrified tiles of approved make and design (thickness to be specified by manufacturer) in all colours & shade in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.
157Size of Tile 600x1200 mm
158Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade(0.10 kg of hardener and 0.20 kg of resin per kg), including filling/grouting and finishing complete as per direction of Engineer-in-charge.
159Size of Tile 600 x 600mm
160Size of Tile 600x1200 mm
161Deduct for not grouting the joints with white cement and matching pigment in the items of fixing of vitrified tiles
162Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.
163Polished Granite stone slab of all colour and texture except Black, Cherry/Ruby Red
164Sub-Head - Roofing
165Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately).
1666 mm thick Cement fiber board, Type-B, Category-III as per IS: 14862 : 2000
167Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.
168(i)Single socketed pipes.
169110 mm diameter
170Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.
171Coupler
172110mm
173Bend 87.5°
174110 mm bend
175Shoe (Plain)
176110 mm Shoe
177Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.
178110 mm
179Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /seIf tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
180Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :
181Ridges plain (500 - 600mm)
182Gutter (600 mm over all girth)
183Barge board (Upto 300 mm)
184Sub-Head : Finishing
18512 mm cement plaster of mix :
1861:6 (1 cement: 6 fine sand)
18715 mm cement plaster on the rough side of single or half brick wall of mix :
1881:6 (1 cement: 6 fine sand)
189Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.
19012 mm cement plaster
191Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :
192Two or more coats on new work.
193Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:
194Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.
195Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer, of required shade and colour all complete :
196New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre
197Finishing walls with Acrylic Smooth exterior paint of required shade :
198New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)
199Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.
200Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
201Providing and fixing 22 gauge chiken wire mesh in required size and shape 150 mm wide and fixed with Bombay nails on vertical and horizontal junctions of RCC and AAC block masonary i/c scaffholding, all leads and lifts etc. Before plastering of surface all complete as per direction of E-In-Charge.
202Sub-Head : Road Work
203Providing and laying BIS approved make 80mm thick factory made cement concrete interlocking paver block of M -40 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.
204Sub-Head : Sanitary Installations
205Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:
206White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests
207Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required :
208W.C. pan with ISI marked white solid plastic seat and lid
209Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :
210Single half stall urinal with 5 litre P.V.C. automatic flushing cistern
211Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern
212Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-
213White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer.
214Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.
215Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :
216Kitchen sink without drain board
217610x510 mm bowl depth 200 mm.
218Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.
219Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.
220Flexible pipe
22132 mm dia
22240 mm dia
223Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
224Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.
225Providing and fixing toilet paper holder :
226C.P. brass
227Providing and laying UPVC SWR pipes 110mm dia. [Type-B category] conforming to IS:13592-2013 of Supreme/ Diplast /Phenolex make, including jointing with suitable PVC adhesive complete as per the direection of Engineer in Charge.
228Providing and laying UPVC SWR [Type-B category] pipes fittings of Supreme/ Diplast /Phenolex make including jointing with suitable PVC adhesive complete as per the direection of engineer in Charge.
229Coupler
230110mm
231Single tee with door
232110x110x110 mm
233Single tee without door
234110x110x110 mm
235Bend 87.5°
236110 mm bend
237Floor Trap 110 mm with CP Grating
238Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and includingcement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. :
239For 100 mm dia. Pipe
240Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.
241450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms.
242Sub-Head : Water Supply
243Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall.
24425 mm dia. nominal bore
24532 mm dia. nominal bore
24640 mm dia. nominal bore
247Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anticorrosive bitumastic paint, cutting chases and making good the wall:
24815 mm dia. nominal bore
24920 mm dia. nominal bore
250Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : External work
25120 mm dia. nominal bore
25225 mm dia. nominal bore
253Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :
25425 to 40 mm nominal bore
255Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :
25625 mm nominal bore
25720 mm nominal bore
25832 mm nominal bore.
259Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :
26020 mm nominal bore
261Providing and fixing uplasticised PVC connection pipe with brass unions :
26245 cm length
26315 mm nominal bore
264Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :
265100 mm diameter
266Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work :
26725 mm diameter pipe.
26832 mm diameter pipe.
26940 mm diameter pipe.
270Providing and filling sand of grading zone V or coarser grade all- round the G.I. pipes in external work.
27132 mm diameter pipe
272Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work)
27315 mm nominal bore
27420 mm nominal bore
27525 mm nominal bore
27632 mm nominal
277Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
278Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931:
27915 mm nominal bore.
280Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 :
28115mm nominal bore
282Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.
283Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements. Weighing not less than 106 gms.
284Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :
285150 mm diameter
286Providing & fixing 15 mm dia CP Brass wall mixer with CP bend for shower arrangement for bathrooms of Victor make of Cera / Jaquar / Ess-Ess or equivalent all complete as per the direction of the Engineer-in-charge
287Providing & fixing 15 mm dia CP Brass kitchen sink wall mixer of Victor make of Cera / Jaquar / Ess-Ess or equivalent all complete as per the direction of the Engineer-in-charge
288Sub Head: Drainage
289Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :
290150 mm diameter
291Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :
292150 mm diameter S.W. pipe
293Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:
294100x100 mm size P type
295With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
296Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :
297Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :
298With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
299Extra for depth for manholes
300Size 90x80 cm
301With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
302Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality
303L D - 2.5
304Rectangular shape 600x450 mm internal dimensions
305Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) with pre-cast R.C.C. vertical grating complete as per standard design :
306With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
307Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.
308With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
309Sub-Head : Aluminium Work
310Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :
311For fixed portion
312Powder coated aluminium (minimum thickness of powder coating 50 micron)
313For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately).
314Powder coated aluminium (minimum thickness of powder coating 50 micron)
315Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):
316With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)
317Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.
318Pre-laminated particle board with decorative lamination on both sides.
319Providing and fixing aluminium round shape handle of outer dia 100mm with SS screws etc. complete as per direction of Engineer-in-charge
320Powder coated minimum thickness 50 micron aluminium
321Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.
322Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg., for doors, including cost of cutting floors ,embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.
323With stainless steel cover plate minimum 1.25 mm thickness.
324Sub-Head : Water Proofing
325Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of:
326(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.
327(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.
328(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.
329(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).
330Providing and fixing GI Spouts in depressed portions, 40mm dia and 60Cm long in Cement Mortar 1:4 (1 Cement: 4 Fine Sand) i/c making arrangement for smooth & efficient functioning of the spout as per the direction of the Engineer-in-charge.
331ELECTRICAL WORK SUB HEAD-I (Wiring)
332Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required
333Group C
334Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required
335Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required
336Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required
337Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required
3382 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
3394 X 1.5 sq. mm + 2 X 1.5 sq. mm earth wire
3404 X 10 sq. mm + 2 X 6 sq. mm earth wire
341Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
34220 mm
34325 mm
344Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/PVC conduit as required.
3452x1.5 sq. mm
3463x1.5 sq. mm
3474x1.5 sq. mm
348Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required.
349Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.
350Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos. of 3 pin 5/6 A modular socket outlet and 2 nos. of 5/6 A modular switch, connections etc. as required.
351Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
3525/6 amps switch
35315/16 amps switch
3543 pin 5/6 amp socket outlet
3556 pin 15/16 amp socket outlet
356TV antenna socket outlet
357RJ-45 Jack with Cat 6 One Module
358Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.
3591 or 2 Module (75mmX75mm)
3604 Module (125mmX75mm)
3618 Module (125mmX125mm)
36212 Module (200mmX150mm)
363Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.
3641 run of cable
365Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.
3661 run of cable
367S/Fixing hexagonal fan box of size 150 mm dia made outof 16 SWG MS sheet including 12mm dia MS rod in the U shape with its vertical legs bent horizontally at the top at least 19 cm on either side and bound to the top reinforcement of the roof at the time of casting i/c S/F 3 mm thick phenolic laminated sheet at the bottom complete as reqd.
368Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
369SUB HEAD-II (Distribution System)
370Supplying and fixing following way, vertical type TPN, sheet steel, MCB distribution board, 415 volts having provision for MCCB as incomer, on surface/ recess, complete with metal door, tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCCB/ RCCB/ Isolator)
3714WAY (4+4+4) Double Door ( Model:-DTVTL004DD of Lauritz & Knudsen
372Supplying and Fixing Four pole, 100A rating MCCB with Fixed Thermal-Fixed Magnetic Release, breaking capacity 10KA at 415V with With Spreader Links for interconnection in the existing vertical DB i/c making interconnection etc as required. (M/s Lauritz & Knudsen , Model-DY125U 100A 10kA FTFM -EM90984OOKO or equivalent similar superior make)
373Supplying and fixing following way, horizontal type SPN / TPN, sheet steel, MCB distribution board, 240/ 415 volts, on surface/ recess, complete with metal door, tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)
3744 Way TPN (8+12) Double Door Glazed ( Make& Model- Lauritz & Knudsen Model-DTTPN004GD-Tripbox NXT)
375Supplying and fixing following rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
3765 amps to 32 amps, 240 volts Single pole.
37763 amps, 415 volts Four pole.
37863 amps, TP MCB
379S/F Following rating MCB power protected unit suitable for operation on 230V single phase AC supply complete with all accessories i/c making interconnection etc as required.
380Supplying and fixing 63 Amps., four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.
381Supplying and fixing Adaptor Box(s) fabricated out of 16 SWG M.S. sheet complete with cutting, welding, painting, sign writing etc. all as required.
382Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.
383SUB HEAD-III (Earthing)
384Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories,and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
385Supplying and laying 25 mm X 5 mm G.I strip on surface or in recess etc as required.
386Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc.as reqd
387Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 56007846
AUTHORITY Government Departments
TENDER VALUE 2.80 Crore
LAST DATE 01-07-2026
Authority
Authority Name Bharat Sanchar Nigam Limited
Work Description Tender for Construction Of Sub Fire Station Building Including Site Development Works At Kandaghat, Distt. Solan (Hp). (Civil And Electrical Work)
Basic Detail
Tender No 15/EE/BSNL/CD/SOL/2026-27
Bidding Type Tender
Location
City Kandaghat
State Himachal Pradesh
Key Dates
Publish Date 16 Jun 2026
Submission Date 01 Jul 2026
Open Date 06 Jul 2026
Finance
Tender Value 2.80 Crore
Tender Fee 1770
EMD 5.61 Lakhs
Exemption Not Available
Document List
7758c2f5-0246-46b0-b5e8-60feaa6a1ce3.html
BOQ_327953.xls
TD15.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Jun 16, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Jul 01, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Completed
Jul 06, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Completed

Tender Documents

Download All (ZIP) ↓
html

7758c2f5-0246-46b0-b5e8-60feaa6a1ce3.html

xls

BOQ_327953.xls

pdf

TD15.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender