|
| 1 | Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer-in-charge Extruded section profile size 48x40 mm |
| 2 | Providing and fixing to existing door frames. 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of ‘H’ section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. ‘U’ cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). |
| 3 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc.,., complete. |
| 4 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. (i)Single socketed pipes. 110 mm diameter |
| 5 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) |
| 6 | Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 7 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap |
| 8 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work ;20 mm nominal outer dia. Pipes. |
| 9 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work ;25 mm nominal outer dia. Pipes. |
| 10 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore. |
| 11 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 : 15 mm nominal bore. |
| 12 | Providing and fixing PTMT grating of approved quality and colour. Circular type. 125 mm nominal dia with 25 mm waste hole. |
| 13 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 20 mm nominal bore, 120 mm long. Weighing not less than 198 gms. |
| 14 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length. |
| 15 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings& accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia |
| 16 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia |
| 17 | Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer- in-charge. |
| 18 | Development of tube well in accordance with IS : 2800 (part I) and IS:11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. |
| 19 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for bore well of: 100 mm dia |
| 20 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 100 mm clamp |
| 21 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 100 mm dia |
| 22 | Providing and fixing CPVC ball valve of approved quality ; 32 mm nominal bore |
| 23 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level.All types of soil: 100 mm dia |
| 24 | Add correction factor @ .973 on DSR 23 from iem no 01 to 21 |
| 25 | Add Cost Index @ 61% on DSR 2023 (from S.N. 01 to 22 |
| 26 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 27 | Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required |
| 28 | SITC 2HP 14 stage 1 phase , suubmersible motor pump set(suitable for 4\\" borewell) outlinvet size 40 mm, head in metres 90M-30M,discharge in 10LPM -95 LPM 130 in the existing borewell including lowering the pump set in to borewell with 40 mm dia medium class HDPE pipe 1ft long coloumn jointed with nut bolts,flange and 02 Nos MS holding clamps heavy duty etc as required Havels/ Crompton/L&T/Kirlosker/Lubi etc |
| 29 | Supply and fixing of 1 phase,230 V,50 HZ digital Submersible pump controller,start capacitor 200/250 mfd,275V and run capacitor 2x36 mfd 440V with digital display for 2 HP 1 phase motor, including fixing on wall/feeder pillar by using suitable size fastner/nuts, bolts and making connection etc as required make- Havels/ Crompton/L&T/Kirlosker etc |
| 30 | Providing & fixing of submersible protection GI rope wire size 6 mm PVC insulate for 2HP submersible pump etc. as required. |
| 31 | Providing & fixing of 40mm dia HDPE PPR column Pipe UV stabilized PN16 pipe including suitable size of couplers,fitting with 2hp submersible pump etc as required. |
| 32 | S/ITC of outdoor type feeder piller, double door made out of 2 mm CRCA sheet duly primed & painted with synthetic enamel gray paint of required size 300 mm deep including SITC of 100 amps, 04 nos insulated aluminium bus bars,P & F of internal connection with suitable size copper wires lugs, following accessories & angle iron frame of suitable size made out of 45 mm x 45 mm x 5 mm thick angle & grouting the same in suitable cement concrete foundation, arrangement for incoming & outgoing cables, cable termination, earthing, locking, interconnection etc. as required. (Face area should be measured.) |
| 33 | Supplying and Laying of one number XLPE insulated and PVC sheathed aluminium unarmoured power cable of 1.1 KV grade of size 2x25 sqmm sq mm direct in the existing open duct /RCC/ HUME/ METAL pipe as required. |
| 34 | Supplying and laying of 40 mm dia (OD-40 mm & ID-34 mm nominal) size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the trench, complete as required. |
| 35 | Supplying and laying of 3x2.5 sq mm flat water proof, PVC insulated and PVC sheathed with electrolytic grade annealed copper conductor cable for submersibla pump motor voltage upto 1100 volt conforms to IS:694 etc in the existing RCC/HUME/Metalpipe/MAsonary open duct as required. |
| 36 | Supplying & fixing of 6 mtr long 65 mm dia G I pipe (medium duty) with suitable size of base plate , baracket and making of suitable collar As per Engineer-In-Charge etc as required at site.. Make Jindal/ TATA/ Bansal/ Hindustan |
| 37 | Supplying & fixing of 100 watt LED street light with aluminium body and toughened glass and secondary optical lens, with IP-66 protection 6500K on existing bracket including wiring with 3 x 1.5 Sqmm (from point to LED fitting), PVC insulated & PVC sheathed, multi core, copper condoctor cable & making connection of LED street light luminaire etc. as required of make Crompton / Bajaj / Havells / Philips. |
| 38 | Supplying & fixing of loop box with lid (195 x 135 x 90) with 6 amp SP MCB(2 Nos), terminals, plastic gland, lugs and accessories etc. as required. Make sintax GSJB product code-2014 or equivalent to Hansel |
| 39 | Total Cost (BoQ1+BoQ2) |
| 40 | Civil work |
| 41 | Elect work Please Enable Macros to View BoQ information |
