Tender For Proposed Construction Of Poumai Naga Cultural Heritage Centre At Senapati District Headquarter.
Tender Value
2.94 Crore
Estimated cost
Bid Submission
06 Jul 2026
4 days left
EMD
5.88 Lakhs
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
As Per Tender Document → Manipur
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Proposed Construction Of Poumai Naga Cultural Heritage Centre At Senapati District Headquarter.
BOQ
| Sl. No. | Item Description |
| 1 | A:CIVIL WORK |
| 2 | Sub-Head 1 :-Surface Dressing |
| 3 | Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15cm deep and disposal of rubbish, lead upto 50m and lift upto 1.5m.All kinds of soil. |
| 4 | Sub-Head 2:-Earth Work |
| 5 | Earth work in excavation in foundation trenches or drains including dressing of sides ramming of bottoms lift up to 1.5 metres including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 metres |
| 6 | Extra for additional lift of 1.5m or part thereof in.All kinds of soil |
| 7 | Filling available excavated earth (excluding rock) in trenches , plinth side of the foundation etc. in layers not exceeding 20 cm in depth ,consolidating each deposited layer by ramming and watering lead up to 50 metres and lift upto 1.5 metres |
| 8 | Supply and filling in plinth with sandy soil under floors including watering, ramming consolidating and dressing complete |
| 9 | Sub-Head 3:-Concrete & RCC Work |
| 10 | Providing and Laying in position cement concrete of specified grade excluding the cost of centering & shuttering ,1:4:8(1cement:4coarse sand : 8 graded stone aggregate 40 mm nominal size). |
| 11 | Providing and laying in position ready mixed plain concrete or site batched design mix cement concrete for reinforced cement concrete work,using coarse aggregate and fine aggregate derived from naturalsources,Portland Pozzolana/Ordinary Portland /Portland slag cement,admixture in recommended proportions as per IS:9103 to accelerate / retard setting of concrete , to improve ductility and workability without imparting strength;including pumping of concrete to site laying, curing, carriage for all leads, but excluding the cost of centering, shuttering, finishing and reinforcement as per directionofEngineer-in-charge;for the following grades of concrete:All works upto plinth Level: Concrete of M25 grade with minimum cement content of 330kg/cum |
| 12 | Providing and laying in position ready mixed plain concrete or site batched design mix cement concrete for reinforced cement concrete work,using coarse aggregate and fine aggregate derived from naturalsources,Portland Pozzolana/Ordinary Portland /Portland slag cement,admixture in recommended proportions as per IS:9103 to accelerate / retard setting of concrete , to improve ductility and workability without imparting strength;including pumping of concrete to site laying, curing, carriage for all leads, but excluding the cost of centering, shuttering, finishing and reinforcement as per directionofEngineer-in-charge;for the following grades of concrete:All works above plinth Level up to Floor V level: Concrete of M25 grade with minimum cement content of 330kg/cum |
| 13 | Reinforced cement concrete work in beams,suspended floors, roofs having slope upto 15 deg landings, balconies, shelves,chajas, lintels, bands,plain window sills, staircase and spiral staircases above plinth level upto floor five level, excluding the cost of centering, shuttering, finishing, and reinforcement with 1:5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregates 20 mm nominal size). |
| 14 | Providing and laying damp proof course 50 mm thick with concrete cement 1:2:4(1 cement : 2 course sand : 4 graded stone aggregate 20 mm nominal size) |
| 15 | Applying a coat of residua lpetroleum bitumen of penetration 80/100 of approved qualit yusing 1.7kg per sqm on damp-proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in Kerosene oil. |
| 16 | Sub-Head 4:-Reinforcement Steel/ Rebar work |
| 17 | Steel reinforcement for RCC work i/c straightening , cutting , bending , placing in position and binding all complete upto plinth Level.Thermo Mechanically Treated Bars |
| 18 | Steel reinforcement for RCC work i/c straightening , cutting , bending , placing in position and binding all complete above plinth Level.Thermo Mechanically Treated Bars |
| 19 | Sub-Head 5:-Form work |
| 20 | Foundation, footings, bases of columns etc. for mass concrete. |
| 21 | Columns, pillars, Piers, Abutments, Posts and Struts. |
| 22 | Stairs except spiral staircases. |
| 23 | Suspended floors, roofs, landings, balconies and access platform, with water proof 12mm ply |
| 24 | Lintels, beams, plinth beams, girders, bressumers and cantilevers, with water proof 12mm ply |
| 25 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc |
| 26 | Sub-Head 6:-Brick work |
| 27 | Brick work with 1st class common burnt clay F.P.S (non modular) bricks in foundation and plinth in: |
| 28 | Full brick upto Plinth Level: |
| 29 | Half brick masonry with first class common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level upto floor V level in Cement mortar 1:4 (1 cement: 4 coarse sand) |
| 30 | Sub-Head 7:-Wood work / alluminium work |
| 31 | Providing woodwork in frames of doors, windows, celestory windows and other frames wrought, framed and fixed in position with hold fast lugs or with dash fastner of required dia and length (hold fast lugs or with dash fastner shall be pais separately) with Local best quality Teak |
| 32 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked MS pressed butt hinges bright finished of required sizes with necessary screws with Local best quality Teak wood 35mm thick |
| 33 | Providing and fixing aluminium sliding bolts ISI marked anodised (anodic coating not less than garde AC 10 as per IS 1868) transparent or dyed to required colour or shade with nuts nad screws etc complete with 300x16mm |
| 34 | Providing and fixing aluminium Tower bolts ISI marked anodised (anodic coating not less than garde AC 10 as per IS 1868) transparent or dyed to required colour or shade with nuts nad screws etc complete with 300x10mm |
| 35 | Providing and fixing chromium plated Brass handles with necessary screws etc.complete.125mm |
| 36 | Providing 40x5mm flat iron hold fast 40cm long I/c fixing to framed with 10 mm dia .bolt nuts and windows plugs and wooden plugs and embedding in cement concrete block 30x10x15mm 1:3:6(1cement:3 coarse sand:6 graded stone aggrt.20mm nominal size) |
| 37 | Providing and fixing aluminium work for doors, windows & ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sectioons of approved make conforming to IS:733 and IS:1285, fixed with rawl plugs and screws or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required EPDM rubber/ Neoprone gasket etc. Aliminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ panelling, CP brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer in charge.(Glazing and panelling to be paid seperately). Anodised aluminium (anodised transparent or dyed to required shade according to IS:1868, Minimum anodic coating of grade AC 15) |
| 38 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/ neprone gasket etc. as per the architectural drawings and the directions of Engineer in charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness. |
| 39 | Filling the gap in between aluminium frame & adjacent RCC/Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer in Charge complete. Upto 5 mm depth and 5 mm width |
| 40 | Sub-Head 8:-Finishing work |
| 41 | 15 mm thick plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix 1:3 ( 1 cement : 3 fine sand ) |
| 42 | 20mm cement plaster of mix 1:4(1 cement:4 fine sand ) . |
| 43 | Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacture over the plastered wall surface to prepare the surface even and smooth complete. |
| 44 | Finishing walls with water proofing cement paint of of required shade: New work (two or more coats applied @ 3.84Kg/10sqm) |
| 45 | Painting with oil type wood preservatives of approved brand and manufacture: New work (two or more coats) |
| 46 | Polishing on wood work with ready made wax polish of approved brand and manufacture: New work |
| 47 | Varnishing with varnish of approved brand and manufacturer:Two or more coats of glue sizing with copal varnish over an under coat of flatting varnish. |
| 48 | Applying one coat of water thinnable cement primer of approved brand and manufacture: Water thinnable cement primer |
| 49 | Finishing walls with textured exterior paint of required shade:New work(two or more coats [email protected]/1sqm)overandincluding base coat of water proofing cement paint applied @2.2kg/10sqm. |
| 50 | Wall painting with premium acrylic emulsion pain to interior grade,having VOC(Volatile Organic Compound )conten tless than 50grams/ litre of approved brand and manufacture,including applying additional coats wherever required to achieve even shade and colour. Two coats |
| 51 | Sub-Head 9:-Flooring work |
| 52 | 62 mm thick concrete flooring with concrete hardener toping under layer 40mm thick cement concrete 1:2:4 (1 cement:2 coarse sand :4 graded stone aggregates of nominal size 20 mm) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix :2 graded stone aggregates 6 mm nominal size ) by volume hardeneing compound is mixed @ 2lit per 50 kg of cement or as per manufacturers specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 53 | Providing and laying Vitrified tiles in floor in different sizes(thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622,of approved brand and manufacturer,in all colour sandshade,laid on 20mm thick cement mortar1:4(1cement:4coarsesand)joining with grey cement [email protected]/sqm including grouting the joints with white cement and matching pigmentsetc.: Size of tiles 600x600mm |
| 54 | Marble stone flooring with 18mm thick marble stone(sample of marble shall be approved by Engineer-in-charge)over 20mm(average)thick base of cement mortar1:4(1Cement:4coarsesand)laid and jointed with grey cement slurry including rubbing and polishing complete with: Udaipur green marble |
| 55 | Extra for prefinished nosing to treads of steps of marble stone |
| 56 | Tile work in skirting,riser of steps and dado(upto2mheight)over 12mm thick bed of cement mortar1:3(1cement:3coarsesand)andjointed with grey cement [email protected]/sqm including pointing in white cement mixed with pigment of matching shade complete: 8mm thick |
| 57 | Sub Head 10: Steel work & Accessories |
| 58 | Providing and fixing stainless steel (Grade304) railing made of Hollow tubes,channels,plates etc,including welding,grinding,buffing,polishing and making curvature (whereever required) and fitting the same with necessary stainless steel nuts and bolt complete,i/c fixing the railing with necessary accessories & stainless steel dash fastners,stainless steel bolts etc,of required size,on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge,(for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolt, fastners etc) |
| 59 | Providing and fixing M.S. grills of required pattern to wooden frames of windows etc. with M.S. flats , square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings/ wooden frames with rawl plugs screws etc. |
| 60 | P/F M.S. fan clamps type-I or II of 16mm dia. and M.S.bar bent to shape with hooked ends in RCC slabs, beams during laying including painting the exposed portion of loop, all as per standard design complete. |
| 61 | B:WATER SUPPLY AND SANITARY INSTALLATION |
| 62 | P/F white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape i/c providing and fixing white vitreous china cistern with dual flush fiiting of flushing capacity 3 lit/6 lit (adjustable to 4 lit/ 8 lit) i/c seat cover and cistern fittings, nuts, bolts and gasket etc. complete |
| 63 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm size respectively with automatic flushing cistern with standard flush pipe and CP brass spreaders with brass unions and GI clamps complete, including painting of ittings and brackets, cutting and making good the walls and floors wherever required: Range of four urinal basin with 10 litre white PVC automatic flushing cistern |
| 64 | Providing and fixing wash basin with CI brackets, 15mm dia CP brass pillar taps, 32 mm C.P brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: White vitreous china wash basin size 630x450mm with a pair of 15mm CP brass pillar tap. |
| 65 | Providing and fixing PTMT Waste Coupling for wash basin and sink of approved quality and colour |
| 66 | Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete.24.37.1 Flexible pipe: 40mm diameter |
| 67 | Providing and fixing PTMT towel rail complete with bracket fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms |
| 68 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings arrangement of approved quality and colour, weighing not less than 105gms |
| 69 | Providing and fixing CPVC. pipes having thermal stability for hot o& cold water supply ,including all CPVC plain & brass threaded fotting, including fixing the pipe with clamps at 1.00 m spacng.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. |
| 70 | 15 mm diameter |
| 71 | 20 mm diameter |
| 72 | 25 mm diameter |
| 73 | 32 mm diameter |
| 74 | Providing and fixing CP brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms .15mm nominal bore. |
| 75 | Providing and fixing of C.P brass stop cock (concealed) of approved quality . 15 mm diameter |
| 76 | Providing and fixing PTMT pillar cock of approved qualityand colour . 15 mm nominal bore ,98 mm long,weighing not less than 75 gms |
| 77 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS:12701 marked,with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but withou fittings and the base support for tank. |
| 78 | Providing and fixing PTMT extension nipple fro water tank pipe, fittings of approved quality and colour.25 mm nominal bore weighing not less than 62 gms |
| 79 | Providing and fixing superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing.Rectangular shape 1500x450 mm |
| 80 | Provoding and fixing PTMT urinal cock of approved quality and colour.15 mm nominal bore, 80 mm long, 42 mm high and 30 mm wide with BSP female threads weighung not less than 48 gms. |
| 81 | Providing and fixing CPVC. pipes having thermal stability for hot o& cold water supply ,including all CPVC plain & brass threaded fotting, including fixing the pipe with clamps at 1.00 m spacng.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. |
| 82 | 100 mm diameter |
| 83 | 150 mm diameter |
| 84 | P/F white vitreous china squatting plate urinal with integral rim longitudinal flush pipe |
| 85 | Providing and fixing PTMT swivelling shower, 15 mm nominal bore weighing not less than 40 gms |
| 86 | Constructing masonry chamber 90x90x100 cm inside ,in brick work in cement mortar 1:4 ( 1 cement : 4 coarse sand ) for sluice valve , with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c neccessary excavation , foundation concrete 1:5:10 ( 1 cement : 5 find sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 ( 1 cement : 3 coarse sand ) 12 mm thick, finished with a floating coat of neat cement complete as per standard design.With 1st class common burnt clay F.P.S ( non modular ) bricks |
| 87 | P/F unplasticised PVC connection pipe with PTMT nuts, collar and bush of approved quality and colour |
| 88 | 15 mm nominal bore, weighing not less than 32 gms |
| 89 | 20 mm nominal bore, weighing not less than 40 gms |
| 90 | 25 mm nominal bore, weighing not less than 62 gms |
| 91 | Elevated Water tank Stand |
| 92 | Structural steel work in single section fixed with or without connecting plate including cutting,hoisting, fixing in position and applying coat of approved steel primer all complete: |
| 93 | C: INTERNAL ELECTRICAL INSTALLATION |
| 94 | Wiring: |
| 95 | Wiring for light point / fan point / exhaust fan point / call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in PVC casing & capping with modular type switch, modular plate, suitable size G.I. box and earthing the point with 1.5mm2 FR PVC insulated copper conductor single core cable etc. as reqd. |
| 96 | Group A |
| 97 | Group B |
| 98 | Group C |
| 99 | Wiring for light point / power plug with 2x4mm2 FR PVC insulated copper conductor single core cable in PVC casing & capping along with 1 no. 4mm2 FR PVC insualted copper conductor single core cable for loop earthing etc. as reqd. |
| 100 | a) Light plug point. |
| 101 | b) Power plug point. |
| 102 | S/F suitable size GI box with modular plate and cover in front on surface /recess i/c P/F 3 pin 5/6 amp socket outlet and 5/6 amp modular switch, connection painting etc. as reqd. (for light plugs to use in non-residential building). |
| 103 | S/F suitable size GI box with modular plate and cover in front on surface /recess i/c P/F 6 pin 15/16 and 5/6 amp modular socket outlet 15/16 amp modular switch, connection painting etc. as reqd. |
| 104 | Wiring for circuit / sub-main wiring along with earth wire with (the following sizes of) FR PVC insulated copper conductor single core cable in PVC casing & capping etc. as reqd. |
| 105 | 1. 2x2.5mm2 +1x2.5mm2 earth wire. |
| 106 | 2. 2 x 4mm2 + 1 x 4mm2 earth wire. |
| 107 | 3. 2 x 6mm2 + 1 x 6mm2 earth wire. |
| 108 | S/D (following size) of FR PVC insulated copper conductor single core cable in existing surface /recessed steel/PVC conduit as reqd. |
| 109 | a) 2x4mm2 |
| 110 | b) 2x6mm2 |
| 111 | c) 4x6mm2 |
| 112 | Supply for 50mm2 4core PVC/XLPE insulated heavy duty armoured cable 1.1KV grade. |
| 113 | Laying of 1 no.PVC insulated PVC sheathed power cable of 1.1KV grade of size not less than 25mm2 but not exceeding 120mm2 direct in ground i/c excavation,Sand cushinoning,protective covering and re-filling the trench etc.as reqd. |
| 114 | Accessories: |
| 115 | S/F 15W Surface mounting LED down light with white powder coated aluminum housing with integrated electronic driver i/c connection as reqd.(HAVELLS) |
| 116 | S/F 110 W Greenbay Highbay. |
| 117 | S/F 450 mm dia wall mounting fan complete with all accessories i/c connection etc. as reqd. regulator etc. as reqd. (Make Bajaj/Usha or Similar). |
| 118 | S/F 305mm sweep exhaust fan complete with all accessories i/c connection etc. As reqd. |
| 119 | S/F 450mm sweep fan complete with all accessories i/c connection etc. As reqd. |
| 120 | Switch Gear: |
| 121 | S/F (2+8 way) single pole and neutral, prewired, sheet steel, MCB distributon board, 240 V on surface/recessd complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, hinged front acrylic cover for MCB knobs, detachable gland plate, interconnection, phosphatized and powder painted including earthing etc. as reqd. (but without MCB/RCCB/Isolator). |
| 122 | S/F 63 amp,double pole, 240 volts, isolator in the existing MCB DB comlete with connections, testing and commissiong etc. as required. |
| 123 | S/F of metal boxes with phenolic laminated sheet cover in front 250mmx300mmx100mm deep. |
| 124 | S/F 5amp to 32amp rating 230V 'B' series MCB for lighting and other load of single pole in the existing MCB DB complete with connection testing and commissioning etc. as reqd. |
| 125 | Earthing Items: |
| 126 | Earthing with copper earth plate 600mm x 600mm x 6mm thick i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe ec. (but without charcoal or coke and salt). |
| 127 | Extra for using salt & charcoal for copper plate earth electrode as reqd. |
| 128 | P/L earth connection from earth electrode with 8 SWG dia G.I. wire in 15mm dia G.I. pipe as reqd. |
| 129 | P/F 8SWG dia GI copper wire on surface or in recessed for loop earthing along with existing surface/ recessed conduit /sub-main wiring /cable as reqd. |
| 130 | D: LAND DEVELOPMENT |
| 131 | Excavation in hilly areas in ordinary rock by mechanical means not requiring blasting.(Excavation in ordinary rock in hilly area by manual means including cutting and trimming of side slopes and disposing of excavated earth with all lifts and lead upto 1000 metres.) |
| 132 | Supply and filling in plinth with sandy soil under floors including watering, ramming consolidating and dressing complete |
| 133 | Felling trees of girth including cutting of trunks and branches removing the roots and stacking of serviceable material and disposal of unserviceable materials. |
| 134 | Beyond 30 cm girth upto and including 60 cm girth |
| 135 | Beyond 60 cm girth upto and including 120 cm girth |
| 136 | E:FIRE FIGHTING |
| 137 | Supplying and fixing of firefighting equiment and material Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 16, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 06, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysJul 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 days